Sensitive optical thin film sensor based on incorporation of 2-(2′-hydroxynaphthylazo)-benzothiazole in a sol–gel matrix for detection of manganese(II) in environmental samples

The highly selective green colorimetric detection of yttrium ions in biological and environmental samples using the synergistic effect in an optical sensor

A new eco-friendly method for creating an optical sensor membrane specifically designed to detect yttrium ions (Y3+) has been developed. The proposed sensor membrane is fabricated by integrating 4-(2-arsonophenylazo) salicylic acid (APASA), sodium tetraphenylborate (Na-TPB), and tri-n-octyl phosphine oxide (TOPO) into a plasticized poly(vinyl chloride) matrix with dimethyl sebacate (DMS) as the plasticizer. In this sensor membrane, APASA functions dually as an ionophore and a chromoionophore, while TOPO enhances the complexation of Y3+ ions with APASA. The composition of the sensor membrane has been meticulously optimized to achieve peak performance. The current membrane exhibits a linear dynamic range for Y3+ ions from 8.0 × 10-9 to 2.3 × 10-5 M, with detection and quantification limits of 2.3 × 10-9 and 7.7 × 10-9 M, respectively. No interference from other potentially interfering cations and anions was observed in the determination of Y3+. The membrane showed strong stability and a swift response time of about 3.0 minutes, with no signs of APASA leaching. This sensor is highly selective for Y3+ ions and can be renewed by treating it with 0.15 M HNO3. It has been effectively applied to measure Y3+ in nickel-based alloys, as well as in biological and environmental samples.

Utilization of a novel PVC- optical sensor for high sensitive and selective determination of zinc ion in real samples

A novel and highly specific bulk membrane optode was developed for the ultra-sensitive detection of zinc(II) in biological, pharmaceutical, and water samples. The polymer inclusion membrane (PIM) utilized in this study consists of 50% polyvinyl chloride (PVC) as a base polymer, 9.00% DOP (dioctylphthalate) as the plasticizer, and 40.0% D2EHPA (di(2-ethlyhexyl)phosphoric acid) as the carrier. To facilitate the spectrophotometric determination of zinc(II), a colorimetric reagent, namely 4-(2-arsonophenylazo) salicylic acid (APASA) {1.00%, m/v}, was employed. When Zn(II) was extracted into the PIM, it led to the creation of the zinc-D2EHPA complex. This complex then underwent a reaction with APASA, resulting in the formation of a red Zn - APASA complex with a maximum absorption wavelength (λmax) of 558 nm. To optimize the response of the optode, a central composite design was employed, considering variables such as the amount of additive and reagent, response time, and pH. When operated under the specific optimal conditions, the sensor demonstrated a limit of quantification (LOQ) of 0.74 ng/mL (equivalent to 1.17 × 10-8 M) and a limit of detection (LOD) of 0.22 ng/mL (equivalent to 3.44 × 10-9 M). The optode membrane demonstrated excellent reproducibility, stability, and a relatively long lifespan, making it suitable for precise and accurate monitoring of Zn(II) ion content. Regeneration of the optode was achieved effectively using 0.25 nitric acid solution, and its response exhibited reversibility and reproducibility, showed a relative standard deviation of less than 1.33%. Moreover, the PIM-APASA optode exhibited a high level of effectiveness in accurately determining the presence of Zn(II) ions in real environmental samples.

An innovative approach in titanium determination based on incorporating 2-amino-4-((4-nitrophenyl)diazenyl)pyridine-3-ol in a PVC membrane

A pioneering optical sensor has been effectively developed to achieve precise and reliable detection of titanium ions. The sensor employs an optode membrane composed of 2-amino-4-((4-nitrophenyl)diazenyl)pyridine-3-ol (ANPDP) and sodium tetraphenylborate (NaTPB) incorporated into a plasticized PVC matrix, with dioctyl sebacate (DOS) acting as the plasticizer. When exposed to Ti4+ ions at pH 8.25, the color of the sensing membrane undergoes a distinctive transformation from yellow-orange to violet. Extensive investigations were carried out to assess and optimize various factors influencing the efficiency of ion uptake. Through careful experimentation, the optimum conditions were determined to be 60.0% DOS, 6.0% ANPDP, 30% PVC, and 4.0% NaTPB, with a rapid response time of 5.0 min. Within these conditions, the developed optode demonstrates an impressive linear range of 3.0-225 ng mL-1, boasting detection (LOD) and quantification (LOQ) limits of 0.91 and 2.95 ng mL-1, respectively. Moreover, the precision of the sensor, as indicated by the relative standard deviation (RSD%), remained consistently below 1.55% in six replicate determinations of 100 ng mL-1 Ti4+ across diverse membranes. The selectivity of the sensor was rigorously examined for a range of cations and anions, successfully establishing the tolerance limits for interfering species. Notably, the presence of EDTA as a masking agent did not compromise the high selectivity of the sensor. Consequently, the innovative probe holds significant potential as a reliable analytical tool for quantifying titanium content in various samples, including water, geological materials, soil, plants, paints, cosmetics, and plastics.

A modified selective optical sensor for selenium determination based on incorporating xylenol orange in a poly(vinyl chloride) membrane

A novel optical sensor has been developed to measure selenium ions. The sensor membrane was created by mixing xylenol orange (XO) and sodium tetraphenylborate (NaTPB) with a plasticized poly(vinyl chloride) membrane that contained o-nitrophenyl octyl ether (o-NPOE) as a plasticizer. XO was previously established for use in a colorimeter to measure selenium in water and other media. At pH 6.6, the color of the detecting membrane changed from orange to pink when in contact with Se4+ ions. Various variables affecting the uptake efficiency were evaluated and optimized. Under optimum conditions (i.e., 30% PVC, 60% o-NPOE, and 5.0% of both XO and NaTPB for 5.0 min as the response time), the proposed sensor displayed a linear range 10-175 ng mL-1 with the detection and quantification limits of 3.0 and 10 ng mL-1, respectively. Also, the precision (RSD%) was better than 2.2% for six replicate determinations of 100 ng mL-1 Se4+ in various membranes. For the detection of Se4+, the selectivity of the sensor membrane was investigated for a number of possible interfering inorganic cations, but no appreciable interference was found. With the use of a 0.3 M HCl solution, the sensor was successfully restored, and the response that may have been reversible and reproducible exhibited an RSD% of less than 2.0%. The sensor has been successfully used to analyze Se4+ ions in environmental and biological materials.

Utilization of a plasticized PVC optical sensor for the selective and efficient detection of cobalt(ii) in environmental samples

A novel sensitive, selective, and reversible cobalt(ii) ion optical sensor was prepared by the incorporation of 5-[o-carboxyphenylazo]2,4-dihydroxybenzoic acid [CPDB] and sodium tetraphenylborate (NaTPB) in a plasticized polyvinyl chloride (PVC) membrane containing dioctyl adipate (DOA) as a plasticizer. The influence of several parameters such as pH, base matrix, solvent mediator and reagent concentration was optimized. A comparison of the obtained results with those of previously reported sensors revealed that the proposed method, in addition to being fast and simple, provided a good linear range (0.05–45.20 μM) and low detection limit (0.015 μM). Low detection and quantification limits and excellent selectivity in the presence of interfering ions such as Fe³⁺, Cu²⁺, Ni²⁺, Ag⁺, Au³⁺, Cr³⁺, Cd²⁺, Zn²⁺, Hg²⁺, and SO₄²⁻ make it feasible to monitor Co²⁺ ion content accurately and repeatedly in environmental samples with complicated matrices. The optode was regenerated successfully using 0.3 M nitric acid (HNO₃) solution while its response was reversible with a relative standard deviation (RSD) lower than 1.9% for seven replicate determinations of 20 μM Co²⁺ in various membranes. The optode was stable and was stored for at least 15 days without observing any change in its sensitivity.

A novel sensitive, selective, and reversible cobalt(ii) ion optical sensor was prepared by the incorporation of [CPDB] and (NaTPB) in a (PVC) membrane containing (DOA) as a plasticizer.