Influence of morphology and topography on potentiometric response of magnesium and calcium sensitive PEDOT films doped with adenosine triphosphate (ATP)

PEDOT doped with algal, mammalian and synthetic dopants: polymer properties, protein and cell interactions, and influence of electrical stimulation on neuronal cell differentiation

PEDOT films were electrochemically polymerised with synthetic and biological dopants, characterised, and their interactions with proteins and neuronal cells investigated.

Developments in the Field of Conducting and Non-conducting Polymer Based Potentiometric Membrane Sensors for Ions Over the Past Decade

Many research studies have been conducted on the use of conjugated polymers in the construction of chemical sensors including potentiometric, conductometric and amperometric sensors or biosensors over the last decade. The induction of conductivity on conjugated polymers by treating them with suitable oxidizing agents won Heeger, MacDiarmid and Shirakawa the 2000 Nobel Prize in Chemistry. Common conjugated polymers are poly(acetylene)s, poly(pyrrole)s, poly(thiophene)s, poly(terthiophene)s, poly(aniline)s, poly(fluorine)s, poly(3-alkylthiophene)s, polytetrathiafulvalenes, polynapthalenes, poly(p-phenylene sulfide), poly(p-phenylenevinylene)s, poly(3,4-ethylenedioxythiophene), polyparaphenylene, polyazulene, polyparaphenylene sulfide, polycarbazole and polydiaminonaphthalene. More than 60 sensors for inorganic cations and anions with different characteristics based on conducting polymers have been reported. There have also been reports on the application of non-conducting polymers (nCPs), i.e. PVC, in the construction of potentiometric membrane sensors for determination of more than 60 inorganic cations and anions. However, the leakage of ionophores from the membranes based on these polymers leads to relatively lower life times. In this article, we try to give an overview of Solid-Contact ISE (SCISE), Single-Piece ISE (SPISE), Conducting Polymer (CP)-Based, and also non-conducting polymer PVC-based ISEs for various ions which their difference is in the way of the polymer used with selective membrane. In SCISEs and SPISEs, the plasticized PVC containing the ionophore and ionic additives govern the selectivity behavior of the electrode and the conducting polymer is responsible of ion-to-electron transducer. However, in CPISEs, the conducting polymer layer is doped with a suitable ionophore which enhances the ion selectivity of the CP while its redox response has to be suppressed.

Conducting polymers in modelling transient potential of biological membranes

The possibility of using conducting polymer (CP) films doped with biological ligands as artificial biological membranes to study potential formation mechanisms is presented. Calcium and magnesium ion-binding anionic sites--asparagine, glutamine, adenosinotriphosphate and heparin are incorporated into the poly(pyrrole) film during electrochemical polymerization. This approach allows the competitive calcium-magnesium ion-exchange to be inspected by open circuit measurements. After a close-to-Nernstian sensitivity of the CP membranes was induced by soaking in alkaline solutions of calcium or magnesium, dynamic experiments were performed by a change in the bulk concentration of magnesium or calcium ions. A characteristic transitory potential response, though distinctively different for the calcium and magnesium ions, was observed and explained using the diffusion layer model (DML).

Influence of electrode rotation on the growth and impedance of a low band gap conducting polymer

Rotation of the electrode during the electrochemical polymerization of delta4,4'-di-cyclopenta[2,1-b;3',4'-b']-dithiophene results in enhanced rates of film growth on the electrode and changes in morphology from dominantly fibrilar to globular structures. The impedance of the resulting films shows their ionic conductivities to be higher than their electronic conductivities. Rotating the electrode during growth enhances electronic conductivities by as much as 2 orders of magnitude, and this is attributed to the dominance of growth of the polymer on the electrode surface (grafting) over the precipitation of material from the diffusion layer.