Alternative sorptive extraction method for gas chromatography determination of halogenated anisoles in water and wine samples

Assessment of commercial porous polyethylene frit for extraction of polycyclic aromatic hydrocarbons from water

Exploring commercial and inexpensive sorbents for extraction of organic pollutants is still an active area of research. Ultrahigh molecular weight polyethylene sieve plate (UMPESP) is a commercially available, low-cost, and porous frit, which has been widely used in solid-phase extraction cartridges to fix the filling materials. In this work, UMPESP was investigated for the extraction of polycyclic aromatic hydrocarbons (PAHs) from water samples. The desorption and sorption efficiencies of UMPESP were first evaluated and compared with two previously reported sorbents, low-density polyethylene plastic pellet (LDPEP) and silicone rod (SR). The comparative results showed that quantitative desorption of analytes from UMPESP, which could be easily achieved with 2 × 1.5 mL n-hexane, was more effective than that of LDPEP (>6 × 1.5 mL n-hexane) and comparable to that of SR. Additionally, shorter equilibrium time was rendered by UMPESP (shaking for 120 min) compared with SR (>480 min), due to the porous structure and larger surface area of the former. Different parameters that affect the extraction efficiency, including organic modifier, ionic strength, and pH value, were then studied. The optimized method coupled with gas chromatography-mass spectrometry afforded good linearity in a concentration range of 10-5000 ng L^-1 (except acenaphthene in the range of 25-5000 ng L^-1) with coefficients of determination ranging from 0.9957 to 0.9995 and relative standard deviations below 13.8%. The limits of detection and quantification were 0.04-3.35 ng L^-1 and 0.13-11.16 ng L^-1, respectively. Finally, the method was successfully applied to determine PAHs in real water samples, and the results showed no statistically significant difference with the concentrations derived from liquid-liquid extraction.

Polyaniline-nylon-6 electrospun nanofibers for headspace adsorptive microextraction

A headspace adsorptive microextraction technique was developed using a novel polyaniline-nylon-6 (PANI-N6) nanofiber sheet, fabricated by electrospinning. The homogeneity and the porosity of the prepared PANI-N6 sheet were studied using the scanning electron microscopy (SEM) and nanofibers diameters were found to be around 200 nm. The novel nanofiber sheet was examined as an extracting medium to isolate some selected chlorobenzenes (CBs), as model compounds, from aquatic media. The extracted analytes were desorbed using μL-amounts of solvent and eventually an aliquot of extractant was injected into gas chromatography-mass spectrometry (GC-MS). Various parameters affecting the extraction and desorption processes were optimized. The developed method proved to be convenient and offers sufficient sensitivity and a good reproducibility. Limits of detection achieved for CBs with the developed analytical procedure ranged from 19 to 33 ng L(-1), while limits of quantification were from 50 to 60 ng L(-1). The relative standard deviations (RSD) at a concentration level of 0.1 ng mL(-1) and 1 ng mL(-1) were in the range of 8-14% and 5-11% (n=3), respectively. The calibration curves of analytes were investigated in the range of 50-1000 ng L(-1) and R(2) between 0.9739 and 0.9932 were obtained. The developed method was successfully applied to the extraction of selected CBs from tap and river water samples. The relative recovery (RR) percentage obtained for the spiked real water samples at 0.1 ng mL(-1) and 1 ng mL(-1) level were 93-103% and 95-104%, respectively. The whole procedure showed to be conveniently applicable and quite easy to handle.