Paper-based solid-state electrochemiluminescence sensor using poly(sodium 4-styrenesulfonate) functionalized graphene/nafion composite film

Optimization and miniaturization of SE-ECL for potential-resolved, multi-color, multi-analyte detection

Electrochemiluminescence (ECL) is a bioanalytical technique with numerous advantages, including the potential for high temporal and spatial resolution, a high signal-to-noise ratio, a broad dynamic range, and rapid measurement capabilities. To reduce the complexity of a multi-electrode approach, we use a single-electrode electrochemiluminescence (SE-ECL) configuration to achieve the simultaneous emission and detection of multiple colors for applications that require multiplexed detection of several analytes. This method exploits intrinsic differences in the electric potential applied along single electrodes built into electrochemical cells, enabling the achievement of distinct colors through selective excitation of ECL luminophores. We present results on the optimization of SE-ECL intensity for different channel lengths and widths, with sum intensities being 5 times larger for 6 cm vs. 2 cm channels and linearly increasing with the width of the channels. Furthermore, we demonstrated for the first time that applying Alternating Current (AC) voltage within the single electrode setup for driving the ECL reactions has a dramatic effect on the emitted light intensity, with square waveforms resulting in higher intensities vs sine waveforms. Additionally, multiplexed multicolor SE-ECL on a 6.5 mm × 3.6 mm CMOS semiconductor image sensor was demonstrated for the first time, with the ability to simultaneously distinguish four different colors, leading to the ability to measure multiple analytes.

Accuracy improvement via novel ratiometry design in distance-based microfluidic paper based analytical device: instrument-free point of care testing

Developing accurate, precise, instrument-free, and point-of-need microfluidic paper-based devices is highly significant in clinical diagnosis and biomedical analysis. In the present work, a ratiometric distance-based microfluidic paper-based analytical device (R-DB-μPAD), along with a three-dimensional (3D) multifunctional connector (spacer), was designed to improve the accuracy and detection resolution analyses. Specifically, the novel R-DB-μPAD was used for the accurate and precise detection of ascorbic acid (AA) as a model analyte. In this design, two channels were fabricated as detection zones, with a 3D spacer located between the sampling and detection zones to improve the detection resolution by preventing the reagents mixing from overspreading between these zones. Two probes for AA were used: Fe³⁺ and 1,10-phenanthroline were deposited in the first channel, and oxidized 3,3',5,5'-tetramethylbenzidine (oxTMB) was added to the second channel. Accuracy improvement of this ratiometry-based design was achieved by enhancing the linearity range and reducing the volume dependency of the output signal. Moreover, the 3D connector improved the detection resolution by eliminating the systematic errors. Under the optimal conditions, the ratio of the distances of the color bands in the two channels was used to construct an analytical calibration curve in the range from 0.05 to 1.2 mM, with a limit of detection of 16 μM. The proposed R-DB-μPAD combined with the connector was successfully used for the detection of AA in orange juice and vitamin C tablets with satisfactory accuracy and precision. This work opens the door for multiplex analysis of various analytes in different matrices.

One-Step Fabrication of Highly Sensitive Tris(2,2'-bipyridyl)ruthenium(II) Electrogenerated Chemiluminescence Sensor Based on Graphene-Titania-Nafion Composite Film

A highly sensitive tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) electrogenerated chemiluminescence (ECL) sensor based on a graphene-titania-Nafion composite film has been prepared in a simple one-step manner. In the present work, a highly concentrated 0.1 M Ru(bpy)₃²⁺ solution was mixed with an as-prepared graphene-titania-Nafion composite solution (1:20, v/v), and then a small aliquot (2 µL) of the resulting mixture solution was cast on a glassy carbon electrode surface. This one-step process for the construction of an ECL sensor shortens the fabrication time and leads to reproducible ECL signals. Due to the synergistic effect of conductive graphene and mesoporous sol-gel derived titania-Nafion composite, the present ECL sensor leads to a highly sensitive detection of tripropylamine from 1.0 × 10⁻⁸ M to 2.0 × 10⁻³ M with a detection limit of 0.8 nM (S/N = 3), which is lower in comparison to that of the ECL sensor based on the corresponding ECL sensor based on the titania-Nafion composite containing carbon nanotube. The present ECL sensor also shows a good response for nicotinamide adenine dinucleotide hydrogen (NADH) from 1.0 × 10⁻⁶ M to 1.0 × 10⁻³ M with a detection limit of 0.4 µM (S/N = 3). Thus, the present ECL sensor can offer potential benefits in the development of dehydrogenase-based biosensors.

Functional Polymers Structures for (Bio)Sensing Application-A Review

In this review we present polymeric materials for (bio)sensor technology development. We focused on conductive polymers (conjugated microporous polymer, polymer gels), composites, molecularly imprinted polymers and their influence on the design and fabrication of bio(sensors), which in the future could act as lab-on-a-chip (LOC) devices. LOC instruments enable us to perform a wide range of analysis away from the stationary laboratory. Characterized polymeric species represent promising candidates in biosensor or sensor technology for LOC development, not only for manufacturing these devices, but also as a surface for biologically active materials' immobilization. The presence of biological compounds can improve the sensitivity and selectivity of analytical tools, which in the case of medical diagnostics is extremely important. The described materials are biocompatible, cost-effective, flexible and are an excellent platform for the anchoring of specific compounds.

Nanomaterial-Modified Conducting Paper: Fabrication, Properties, and Emerging Biomedical Applications

The emerging demand for wearable, lightweight portable devices has led to the development of new materials for flexible electronics using non-rigid substrates. In this context, nanomaterial-modified conducting paper (CP) represents a new concept that utilizes paper as a functional part in various devices. Paper has drawn significant interest among the research community because it is ubiquitous, cheap, and environmentally friendly. This review provides information on the basic characteristics of paper and its functionalization with nanomaterials, methodology for device fabrication, and their various applications. It also highlights some of the exciting applications of CP in point-of-care diagnostics for biomedical applications. Furthermore, recent challenges and opportunities in paper-based devices are summarized.

Fabrication, Flow Control, and Applications of Microfluidic Paper-Based Analytical Devices

Paper-based microfluidic devices have advanced significantly in recent years as they are affordable, automated with capillary action, portable, and biodegradable diagnostic platforms for a variety of health, environmental, and food quality applications. In terms of commercialization, however, paper-based microfluidics still have to overcome significant challenges to become an authentic point-of-care testing format with the advanced capabilities of analyte purification, multiplex analysis, quantification, and detection with high sensitivity and selectivity. Moreover, fluid flow manipulation for multistep integration, which involves valving and flow velocity control, is also a critical parameter to achieve high-performance devices. Considering these limitations, the aim of this review is to (i) comprehensively analyze the fabrication techniques of microfluidic paper-based analytical devices, (ii) provide a theoretical background and various methods for fluid flow manipulation, and iii) highlight the recent detection techniques developed for various applications, including their advantages and disadvantages.

Multifunctional solid-state electrochemiluminescent chemosensors and aptasensor with free-standing active sites based on task-specific pyrene-terminated polymers via RAFT polymerization

Based on the flexible molecular engineering technique of reversible addition-fragmentation chain transfer (RAFT) polymerization, various polymers carrying positive or negative charges and different terminal groups such as pyrene or tertiary amine were synthesized for fabricating multifunctional solid-state electrochemiluminescent (ECL) sensors. Accordingly, the chemosensors immobilizing the ECL probe or co-immobilizing the ECL probe and the coreactant were realized for the quantification of small molecules (e.g., tripropylamine, tetracycline), and an aptasensor was developed for the specific and sensitive lysozyme assay (limit of detection: 0.1 ng/mL). All of the sensors were realized via a simple design exploiting the π-π stacking and electrostatic interactions. It was confirmed that the proposed strategy is simple but universal for the fabrication of versatile ECL sensors that showed simplicity, cost-effectiveness, high sensitivity, long-term stability, and excellent reproducibility.

Paper-Based Sensor Chip for Heavy Metal Ion Detection by SWSV

Heavy metal ion pollution problems have had a terrible influence on human health and the environment. Therefore, the monitoring of heavy metal ions is of great practical significance. In this paper, an electrochemical three-electrode system was fabricated and integrated on nitrocellulose membrane (NC) by the use of magnetron sputtering technology, which exhibited a uniform arrangement of porous structure without further film modification. This paper-based sensor chip was used for Cu²⁺ detection by square-wave stripping voltammetry (SWSV). Within the ranges of 5–200 μg·L⁻¹ and 200–1000 μg·L⁻¹, it showed good linearity of 99.58% and 98.87%, respectively. The limit of detection was 2 μg·L⁻¹. On the basis of satisfying the detection requirements (10 μg·L⁻¹), the integrated sensor was small in size and inexpensive in cost. Zn²⁺, Cd²⁺, Pb²⁺ and Bi³⁺ were also detected by this paper-based sensor chip with good linearity.

Fluorescence Sensing with Cellulose-Based Materials

Cellulose-based materials functionalized with fluorescence sensors are highly topical and are employed in many areas of functional materials, including the sensing of heavy-metal ions and anions as well as being widely used as chemical sensors and tools for environmental applications. In this Review, we cover recent progress in the development of cellulose-based fluorescence sensors as parts of membranes and nanoscale materials for the detection of biological analytes. We believe that this Review will be of interest to chemists, chemical engineers, and biochemists in the sensor community as well as researchers working with biological material systems.

Graphene as Transparent Electrodes: Fabrication and New Emerging Applications

Graphene has been regarded as a promising candidate for a new generation of transparent electrodes (TEs) due to its prominent characteristics including high optical transmittance, exceptional electronic transport, outstanding mechanical strength, and environmental stability. Comprehensive and critical insights into the latest advances in graphene-based TEs (GTEs) since, but not limited to 2013, are provided, with an emphasis on fabrication, modification, and versatile applications. Several emerging application areas not previously summarized, including electrochromic devices, supercapacitors, electrochemical and electrochemiluminescent sensors, are discussed in detail. The challenges and prospects in these fields are also addressed.

Simultaneous utilization of a bifunctional ruthenium complex as an efficient catalyst for RAFT controlled photopolymerization and a sensing probe for the facile fabrication of an ECL platform

The ruthenium complex played simultaneous bifunctional roles as an efficient catalyst for RAFT-controlled photopolymerization and a sensing probe for the facile fabrication of an ECL platform.

Biomarker detection for disease diagnosis using cost-effective microfluidic platforms

Early and timely detection of disease biomarkers can prevent the spread of infectious diseases, and drastically decrease the death rate of people suffering from different diseases such as cancer and infectious diseases. Because conventional diagnostic methods have limited application in low-resource settings due to the use of bulky and expensive instrumentation, simple and low-cost point-of-care diagnostic devices for timely and early biomarker diagnosis is the need of the hour, especially in rural areas and developing nations. The microfluidics technology possesses remarkable features for simple, low-cost, and rapid disease diagnosis. There have been significant advances in the development of microfluidic platforms for biomarker detection of diseases. This article reviews recent advances in biomarker detection using cost-effective microfluidic devices for disease diagnosis, with the emphasis on infectious disease and cancer diagnosis in low-resource settings. This review first introduces different microfluidic platforms (e.g. polymer and paper-based microfluidics) used for disease diagnosis, with a brief description of their common fabrication techniques. Then, it highlights various detection strategies for disease biomarker detection using microfluidic platforms, including colorimetric, fluorescence, chemiluminescence, electrochemiluminescence (ECL), and electrochemical detection. Finally, it discusses the current limitations of microfluidic devices for disease biomarker detection and future prospects.

Tailor-made functional surfaces based on cellulose-derived materials

As one of the most abundant natural materials in nature, cellulose has revealed enormous potential for the construction of functional materials thanks to its sustainability, non-toxicity, biocompatibility, and biodegradability. Among many fascinating applications, functional surfaces based on cellulose-derived materials have attracted increasing interest recently, as platforms for diagnostics, sensoring, robust catalysis, water treatment, ultrafiltration, and anti-microbial surfaces. This mini-review attempts to cover the general methodology for the fabrication of functional cellulose surface and a few popular applications including bioactive and non-adhesive (i.e., anti-fouling and anti-microbial) surfaces.

Chip-based generation of carbon nanodots via electrochemical oxidation of screen printed carbon electrodes and the applications for efficient cell imaging and electrochemiluminescence enhancement

A portable lab-on-a-chip methodology to generate ionic liquid-functionalized carbon nanodots (CNDs) was developed via electrochemical oxidation of screen printed carbon electrodes. The CNDs can be successfully applied for efficient cell imaging and solid-state electrochemiluminescence sensor fabrication on the paper-based chips.

Low-cost, high-throughput fabrication of cloth-based microfluidic devices using a photolithographical patterning technique

In this work, we first report a facile, low-cost and high-throughput method for photolithographical fabrication of microfluidic cloth-based analytical devices (μCADs) by simply using a cotton cloth as a substrate material and employing an inexpensive hydrophobic photoresist laboratory-formulated from commercially available reagents, which allows patterning of reproducible hydrophilic-hydrophobic features in the cloth with well-defined and uniform boundaries. Firstly, we evaluated the wicking properties of cotton cloths by testing the wicking rate in the cloth channel, in combination with scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analyses. It is demonstrated that the wicking properties of the cloth microfluidic channel can be improved by soaking the cloth substrate in 20 wt% NaOH solution and by washing the cloth-based microfluidic patterns with 3 wt% SDS solution. Next, we studied the minimum dimensions achievable for the width of the hydrophobic barriers and hydrophilic channels. The results indicate that the smallest width for a desired hydrophobic barrier is designed to be 100 μm and that for a desired hydrophilic channel is designed to be 500 μm. Finally, the high-throughput μCADs prepared using the developed fabrication technique were demonstrated for colorimetric assays of glucose and protein in artificial urine samples. It has been shown that the photolithographically patterned μCADs have potential for a simple, quantitative colorimetric urine test. The combination of cheap cloth and inexpensive high-throughput photolithography enables the development of new types of low-cost cloth-based microfluidic devices, such as "microzone plates" and "gate arrays", which provide new methods to perform biochemical assays or control fluid flow.

PSS-GN nanocomposites as highly-efficient peroxidase mimics and their applications in colorimetric detection of glucose in serum

PSS-GN nanocomposites were firstly proposed as a peroxidase-like mimic successfully and utilized in the determination of glucose in serum samples.

Microfluidic paper-based devices for bioanalytical applications

Paper has become increasingly recognized as a very interesting substrate for the construction of microfluidic devices, with potential application in a variety of areas, including health diagnosis, environmental monitoring, immunoassays and food safety. The aim of this review is to present a short history of analytical systems constructed from paper, summarize the main advantages and disadvantages of fabrication techniques, exploit alternative methods of detection such as colorimetric, electrochemical, photoelectrochemical, chemiluminescence and electrochemiluminescence, as well as to take a closer look at the novel achievements in the field of bioanalysis published during the last 2 years. Finally, the future trends for production of such devices are discussed.

An ionogel composite including copolymer nanowires for disposable electrochemiluminescent sensor configurations

Aniline derivatives such as luminol and benzidines can be electropolymerized for the preparation of electrochemiluminescent sensors.