Porous monoliths for on-line sample preparation: A review

Effect of crosslinker/porogen ratio on sponge-nested polymer monoliths for solid-phase extraction

Polymer monoliths can be polymerised within different molds, but limited options are available for the preparation of free-standing polymer monoliths for analytical sample preparation, and in particular, solid-phase extraction (SPE). Commercial melamine-formaldehyde sponges can be used as supports for the preparation of polymer monoliths, due its flexibility, giving various shapes to monoliths. Herein, the crosslinker/porogen ratio of highly porous sponge-nested divinylbenzene (DVB) polymer monoliths has been evaluated. Monoliths prepared using different crosslinker/porogen ratios were applied to the extraction of bisphenol F, bisphenol A, bisphenol AF, and bisphenol B. Monoliths containing 50 wt % DVB and 50 wt % porogens presented the highest recovery of bisphenols. Under the optimised conditions, the developed method showed a linear range between 2.5 µg L-1 and 150 µg L-1 for BPA and BPAF, and between 5 µg L-1 and 150 µg L-1 for BPB and BPF. The limits of detection (LOD, S/N = 3) and limits of quantification (LOQ, S/N = 10) ranged from 0.36 µg L-1 to 1.09 µg L-1, and from 1.20 µg L-1 to 3.65 µg L-1, respectively. The recoveries for spiked bisphenols (10 µg L-1) in tap water and water contained in a polycarbonate containers were between 82 % and 114 %.

Aptamer based hybrid monolithic pipette tips supported by melamine sponge for enrichment of proteins

BACKGROUND

The convenient preparation and application of functionalized organic-inorganic hybrid monolithic materials have obtained substantial interest in the pretreatment of complex samples by solid-phase extraction (SPE). Compared to the in-tube solid-phase microextraction in fused-silica capillaries, micro SPE in plastic pipette tips have fascinating merits for the easily operated enrichment of trace target analytes from biological samples. However, the poor compatibility of organic-inorganic hybrid monoliths with plastics leads to the rare appearance of commercial hybrid monolithic pipette tips (HMPTs). Therefore, how to synthesize the organic-inorganic hybrid monolithic materials with better extraction performance in plastic pipette tips becomes a challenge.

RESULTS

We develop a facile and cheap strategy to immobilize organic-inorganic hybrid monoliths in pipette tips. Melamine sponge was employed as the supporting skeleton to in situ assemble amine- and thiol-bifunctionalized hybrid monolithic material via "one pot" in a pipette tip, and gold nanoparticles (GNPs) and thiol-modified aptamer against human α-thrombin were sequentially attached to the hybrid monolith within the HMPTs. The average coverage density of the aptamer with GNPs as an intermediary reached as high as 818.5 pmol μL-1. The enriched thrombin concentration was determined by a sensitive enzymatic chromogenic assay with the limit of detection of 2 nM. The extraction recovery of thrombin at 10 nM in human serum was 86.1 % with a relative standard deviation of 6.1 %. This proposed protocol has been applied to the enrichment and determination of thrombin in real serum sample with strong anti-interference ability, low limit of detection and high recovery.

SIGNIFICANCE

The amine- and thiol-bifunctionalized HMPTs prepared with sponge as the skeleton frame provided a novel substrate material to decorate aptamers for efficient enrichment of proteins. This enlightens us that we can take advantage of the tunability of sponge assisted HMPTs to produce and tailor a variety of micro SPE pipette tips for broader applications on the analysis of trace targets in complex biological, clinic and environmental samples.

Construction of a highly efficient adsorbent for one-step purification of recombinant proteins: Functionalized cellulose-based monolith fabricated via phase separation method

Currently, purification step in the recombinant protein manufacture is still a great challenge and its cost far outweighs those of the upstream process. In this study, a functionalized cellulose-based monolith was constructed as an efficient affinity adsorbent for one-step purification of recombinant proteins. Firstly, the fundamental cellulose monolith (CE monolith) was fabricated based on thermally induced phase separation, followed by being modified with nitrilotriacetic acid anhydride through esterification to give NCE monolith. After chelating with Ni2+, the affinity adsorbent NCE-Ni2+ monolith was obtained, which was demonstrated to possess a hierarchically porous morphology with a relatively high surface area, porosity and compressive strength. The adsorption behavior of NCE-Ni2+ monolith towards β2-microglobulin with 6 N-terminus His-tag (His-β2M) was evaluated through batch and fixed-bed column experiments. The results revealed that NCE-Ni2+ monolith exhibited a relatively fast His-β2M adsorption rate with a maximum adsorption capacity of 329.2 mg/g. The fixed-bed column adsorption implied that NCE-Ni2+ monolith showed high efficiency for His-β2M adsorption. Finally, NCE-Ni2+ monolith was demonstrated to have an excellent His-β2M purification ability from E. coli lysate with exceptional reusability. Therefore, the resultant NCE-Ni2+ monolith had large potential to be used as an efficient adsorbent for recombinant protein purification in practical applications.

4D-Printed Elution-Peak-Guided Dual-Responsive Monolithic Packing for the Solid-Phase Extraction of Metal Ions

Four-dimensional printing (4DP) technologies are revolutionizing the fabrication of stimuli-responsive devices. To advance the analytical performance of conventional solid-phase extraction (SPE) devices using 4DP technology, in this study, we employed N-isopropylacrylamide (NIPAM)-incorporated photocurable resins and digital light processing three-dimensional printing to fabricate an SPE column with a [H+]/temperature dual-responsive monolithic packing stacked as interlacing cuboids to extract Mn, Co, Ni, Cu, Zn, Cd, and Pb ions. When these metal ions were eluted using 0.5% HNO3 solution as the eluent at a temperature below the lower critical solution temperature of polyNIPAM, the monolithic packing swelled owing to its hydrophilic/hydrophobic transition and electrostatic repulsion among the protonated units of polyNIPAM. These effects resulted in smaller interstitial volumes among these interlacing cuboids and improvements in the elution peak profiles of the metal ions, which, in turn, demonstrated the reduced method detection limits (MDLs; range, 0.2-7.2 ng L-1) during analysis using inductively coupled plasma mass spectrometry. We studied the effects of optimizing the elution peak profiles of the metal ions on the analytical performance of this method and validated its reliability and applicability by analyzing the metal ions in reference materials (CASS-4, SLRS-5, 1643f, and Seronorm Trace Elements Urine L-2) and performing spike analyses of seawater, groundwater, river water, and human urine samples. Our results suggest that this 4D-printed elution-peak-guided dual-responsive monolithic packing enables lower MDLs when packed in an SPE column to facilitate the analyses of the metal ions in complex real samples.

Organic-silica hybrid monolithic sorbents for sample preparation techniques: A review on advances in synthesis, characterization, and applications

Organic-silica hybrid monolithic materials have attracted considerable attention as potential stationary phases in separation science. These materials combine the advantages of organic polymer and silica-based monoliths, including easy preparation, lower back pressure, high permeability, excellent mechanical strength, thermal stability, and tunable surface chemistry with high surface area and selectivity. The outstanding chromatographic efficiency as stationary phase of hybrid monolithic capillary columns for capillary liquid chromatography and capillary electrochromatography has been reported in many papers. Organic-silica hybrid monolithic materials have also been extensively used in the field of sample preparation. Owing to their surface functionalities, these porous sorbents offer unique selectivity for pre-concentration of different analytes in the most complex matrixes by fast dynamic transport. These sorbents not only improve the analytical method sensitivity, but also introduce novelties in terms of extraction devices and instrument coupling strategies. The current review covers the period spanning from 2017 to 2023 and describes the properties of organic-inorganic hybrid monolithic materials, the present status of this technology and summarizes recent developments in their use as innovative sorbents for microextraction sample preparation techniques (solid phase microextraction with pipette tip, offline in-tube SPME, in-tube SPME online with LC, and in-tube SPME directly coupled with mass spectrometry). Aspects such as the synthesis methods (sol-gel process, one-pot approach, and polyhedral oligomeric silsesquioxanes-based procedure), characterization techniques, and strategies to improve extraction efficiency in various applications in different areas (environmental, food, bioanalysis, and proteomics) are also discussed.

Review of recent advances in development and applications of organic-silica hybrid monoliths

Organic-silica hybrid monoliths attracted attention as an alternative to extensively researched organic polymer-based and silica-based counterparts. The development and applications of these materials as extraction and separation media in capillary liquid chromatography and capillary electrochromatography were previously reviewed in several manuscripts. In this review, we will concentrate on work published since mid-2016 focusing on advances in their development using sol-gel chemistry of tetra- and trialkoxysilanes and subsequent surface modification with organic monomers, and "one-pot" strategy incorporating sol-gel chemistry of alkoxysilanes and free-radical polymerization, ring-opening polymerization, or thiol-based click polymerization with organic monomers. Approaches adapted to the preparation of hybrid monoliths made with polyhedral oligomeric silsesquioxanes will be covered as well.

Sponge-nested polymer monoliths: Versatile materials for the solid-phase extraction of bisphenols

Polymer monoliths are promising materials for sample preparation due to their high porosity, pH stability, and simple preparation. The use of melamine formaldehyde foams has been reported as an effective support to prepare highly robust silica and polymer monoliths. Herein, divinylbenzene monoliths based on a 50:50 (%, w/w) crosslinker/porogen ratio have been nested within a melamine-formaldehyde sponge, resulting in monoliths with a surface area higher than 400 m2 /g. The extraction performance of these monoliths was evaluated for the extraction of endocrine-disrupting bisphenols from aqueous solutions. We evaluated for the first time the versatility of sponge-nested polymer monoliths by comparing three different extraction modes (vortex mixing, magnetic stirring, and orbital shaking). Vortex mixing showed a comparable recovery of bisphenols (39%-81%) in a shorter extraction time (30 min, instead of 2 h). In addition, the robustness of the sponge-nested polymer monoliths was demonstrated for the first time by reshaping a larger monolithic cube (0.125 cm3 ) into four smaller pieces (4 × 0.03125 cm3 ) leading to a 16%-21% increase in extraction efficiency. This effect was attributed to an increase in the effective contact area with the sample, obtaining a higher analyte extraction capacity.

Solid-phase microextraction with MIL-53(Al)-polymer monolithic column coupled to pressurized capillary electrochromatography for determination of chlorogenic acid and ferulic acid in sugarcane samples

In this paper, a polymer monolithic column based on poly (Butyl methacrylate-co-ethylene glycol dimethacrylate) (poly (BMA-co-EDGMA)) doped with MIL-53(Al) metal-organic framework (MOF) was prepared using an in situ polymerization method. The characteristics of MIL-53(Al)-polymer monolithic column were studied through scanning electron microscopy (SEM), Fourier transform infrared spectrometry (FT-IR), energy-dispersive spectroscopy (EDS), X-ray powder diffractometry (XRD), and nitrogen adsorption experiment. Due to its large surface area, the prepared MIL-53(Al)-polymer monolithic column has good permeability and high extraction efficiency. Using MIL-53(Al)-polymer monolithic column for solid-phase microextraction (SPME), coupled to pressurized capillary electrochromatography (pCEC), a method for the determination of trace chlorogenic acid and ferulic acid in sugarcane was established. Under optimized conditions, chlorogenic acid and ferulic acid have a good linear relationship (r ≥ 0.9965) within the concentration range of 50.0-500 µg/mL, the detection limit is 0.017 µg/mL, and the relative standard deviation (RSD) is less than 3.2%. The spike recoveries of chlorogenic acid and ferulic acid were 96.5% and 96.7%, respectively. The results indicate that the method is sensitive, practical, and convenient. It has been successfully applied to the separation and detection of trace organic phenolic compounds in sugarcane samples.

Preparation of miniaturized hydrophilic affinity monoliths: Towards a reduction of non-specific interactions and an increased target protein density

In affinity chromatography, non-specific interactions between the ligands and the affinity column may affect the results, leading to misinterpretations during the investigation of protein-ligand interactions (detection of false positives in ligand screening, lack of specificity in purification). Such non-specific interactions may arise both from the underlying support or from the target protein itself. If the second ones are protein-dependent (and cannot be studied in a general framework), the first ones occur in the same way regardless of the immobilized target. We propose a methodology to identify the origin of such non-specific interactions with the underlying material of the affinity column. This methodology relies on the systematic investigation of the retention behavior of a set of 41 low-molecular weight compounds covering a wide chemical space (net charge, log D, functionality). We first demonstrate that the main source of non-specific interactions on the most commonly used GMA-co-EDMA monolith comes from hydrophobic effects. To reduce such non-specific interactions, we developed a new hydrophilic glycidyl methacrylate-based monolith by replacing the EDMA crosslinker by the more hydrophilic NN' Methylenebisacrylamide (MBA). Optimization of the synthesis parameters (monomer content, initiation type, temperature) has focused on the reduction of non-specific interaction with the monolithic support while maximizing the amount of protein that can be grafted onto the monolith at the issue of its synthesis. The retention data of the 41 test solutes on the new poly(GMA-co-MBA) monolith shows a drastic reduction of non-specific interactions except for cationic compounds. The particular behavior of cationic compounds is due to their electrostatic interactions with carboxylic groups resulting from the partial acidic hydrolysis of amide groups of MBA during the epoxide ring opening step. So, the ring opening step in acidic media was replaced by a hot water treatment to avoid side reaction on MBA. The new monolith poly(GMA-co-MBA) not only has improved hydrophilic surface properties but also a higher protein density (16 ± 0.8 pmol cm^-1 instead of 8 ± 0.3 pmol cm^-1). To highlight the benefits of this new hydrophilic monolith for affinity chromatographic studies, frontal affinity chromatography experiments were conducted on these monoliths grafted with con A.

Sponge-nested polymer monolith sorptive extraction

Polymer monoliths are an alternative to traditional particle-packed supports used in solid-phase extraction because of their ease of preparation, high porosity, and pH stability. They often required the attachment of monoliths to a support, such as the internal walls of a column to enable their use for sample preparation. Applications of free-standing polymer monoliths are rarely found because of their limited mechanical stability. Herein, divinylbenzene monoliths were polymerised within a commercial melamine-formaldehyde sponge using different polymerisation times. The sponge-nested polymer monoliths are highly robust, and their size and shape can be easily adjusted for desired applications. The prepared sponge-nested polymer monoliths had surface areas in the range of 237 m² g^-1 to 369 m² g^-1. A melamine-formaldehyde sponge cut into 1 cm³ cubes were used to template the polymer monoliths. Miniaturized monoliths with a size of 0.125 cm³ were directly cut from the larger cubes without compromising the integrity of the porous monolith structure. The resulting nested monolith sorptive extraction (NMSE) supports were applied for the extraction of the endocrine disruptors bisphenol A, 4-tert-butylphenol, and 4-tert-octylphenol. The prepared sponge-nested monoliths are low-cost (40 monoliths/AU$). NMSE was carried out by the direct immersion of the monoliths in the aqueous standards/samples, requiring only an orbital shaker for the extraction procedure. Best performance was obtained for polymer monoliths polymerized for 6 h, enabling limits of detection of 5.6 to 6.5 µg L^-1 for the selected analysis using HPLC-UV.

Analysis of carbohydrates and glycoconjugates by matrix-assisted laser desorption/ionization mass spectrometry: An update for 2017-2018

This review is the tenth update of the original article published in 1999 on the application of matrix-assisted laser desorption/ionization mass spectrometry (MALDI) mass spectrometry to the analysis of carbohydrates and glycoconjugates and brings coverage of the literature to the end of 2018. Also included are papers that describe methods appropriate to glycan and glycoprotein analysis by MALDI, such as sample preparation techniques, even though the ionization method is not MALDI. Topics covered in the first part of the review include general aspects such as theory of the MALDI process, new methods, matrices, derivatization, MALDI imaging, fragmentation and the use of arrays. The second part of the review is devoted to applications to various structural types such as oligo- and poly-saccharides, glycoproteins, glycolipids, glycosides, and biopharmaceuticals. Most of the applications are presented in tabular form. The third part of the review covers medical and industrial applications of the technique, studies of enzyme reactions, and applications to chemical synthesis. The reported work shows increasing use of combined new techniques such as ion mobility and highlights the impact that MALDI imaging is having across a range of diciplines. MALDI is still an ideal technique for carbohydrate analysis and advancements in the technique and the range of applications continue steady progress.

Determination of polycyclic aromatic hydrocarbons in surface waters by high performance liquid chromatography previous to preconcentration through solid-phase extraction by using polymeric monoliths

A simple, sensitive and reproducible solid-phase extraction method using plastic cartridges containing a monolithic sorbent (m-SPE), coupled to reverse phase liquid chromatography analysis, aiming to determine fifteen polycyclic aromatic hydrocarbons in surface water samples, was developed. The sorbent was easily prepared through a thermal polymerization reaction by using a mixture of n-butyl methacrylate as non-polar monomer and ethylene glycol dimethacrylate as crosslinker contained in a typical Polypropylene syringe cartridge. The effect of different parameters (type of hydrophobic monomer, elution solvent, sample volume, sorbent amount and sorbent load capacity) on the extraction efficiency was optimized. The optimal conditions were achieved by using n-butyl methacrylate as monomer, tetrahydrofurane (THF) as solvent for sorbent cleaning, THF:acetone (1:1) as elution solvent, 25.00 mL of sample volume, 600 µL of the polymerization mixture and 60 µg L^-1 as sample loading capacity. Finally, the sorbent charge capacity, the reusability of the cartridges and the extraction efficiency of the m-SPE monolith, as compared with a typical C8 cartridge, were evaluated. Under the optimized experimental conditions, enrichment factors were between 76 and 103, relative recovery factors from 78 to 103%, accuracy values in the range of 58 to 98%, and inter-batch reproducibility values from between 2 and 10%, were obtained. The limits of detection and quantification were obtained by two different procedures: the signal to noise (S/N) ratios (3 and 10, respectively) and the IUPAC convention. The lowest LOD and LOQ values, obtained with the S/N ratios, were between 0.02 and 1.00 µg L^-1, respectively whereas with the IUPAC convention the values were between 0.07 and 5 µg L^-1. Using this procedure, several PAHs could be detected in the surface water sample taken from a river stream located in La Plata city (Buenos Aires Province, Argentina).

Novel chemically cross-linked self-molding particulate sorbents as solid-phase extraction media

Here, we describe novel, chemically cross-linked, self-molding particulate polymer sorbents that are utilized as a molding-type solid-phase extraction medium (M-SPEM), which exhibits high permeability and rigidness. To fabricate such M-SPEM, first, polyethyleneimine (PEI)-modified reversed-phase (RP)-type particulate sorbents were synthesized, thereafter, they were chemically cross-linked by a polymer having many epoxy groups together with additional PEI. By optimizing the binding conditions of the particulate sorbents, the resultant M-SPEM has almost the same adsorption properties as the corresponding unmolded particulate sorbent for some polar (e.g., uracil and adenine) compounds. The binding technique proposed here is expected to facilitate the fabrication of molding-type sorbents and improve the performance of the SPE procedure.

Recent Advances in Solid-Phase Extraction as a Platform for Sample Preparation in Biomarker Assay

Low levels of biomarkers and the complexity of bio sample make the analytical assay of several biomarkers a challenging issue. Suitable sample preparation run remain a vital part of the puzzle of diagnostic level. Enhancing the detection limit of bioanalytical methods start during the sample preparation procedure. A robust sample preparation method is needed to evaluate the number of biomarkers. As worldwide environmental issues attract expanding consideration, all the more harmless to the ecosystem investigations are liked. Solid-phase extraction (SPE) is an appealing strategy among the sample treatment methods due to the versatility of sorbent materials, less solvent consumption, and compatibility with analytical devices. Miniaturization of the SPE gives the chance to integrate the other analytical steps in a single run, known as an easy-to-use and effective method. SPE utilizes various SPE sorbent beds such as packed beads, porous polymer monoliths, molecularly imprinted polymers, membranes, or other magnetic form microstructures to achieve high surface-to-volume ratio and appropriate chemical properties effective extraction. Also, SPE is the methodology of interest to fulfill high recovery and efficiency demands. In this review, we intend to explain more recent methods for the rational design of SPE and miniaturized SPE to determine biomarkers from biological media. The headlines are subdivided into (1) packing materials in SPE, (2) setups for sample preparation by magnetic SPE, and (3) and future perspective for the application of SPE in sample preparation for analysis of biomarkers.

A novel polyhedral oligomeric silsesquioxane-based hybrid monolith as a sorbent for on-line in-tube solid phase microextraction of bisphenols in milk prior to high performance liquid chromatography-ultraviolet detection analysis

An on-line in-tube solid-phase microextraction (in-tube SPME) coupled with high-performance liquid chromatography (HPLC) method was proposed based on a novel polyhedral oligomeric silsesquioxane (POSS)-hybrid monolith for the determination of four bisphenols (BPs) in milk. The monolith was synthesized using acrylamide (AM) and monomethacrylate-functionalized POSS (mono-MA-POSS) as functional monomers to copolymerize with ethylene dimethacrylate (EDMA). Due to the abundant hydrogen bonding, π-π and hydrophobic interaction sites, the synthetic monolith displayed satisfying extraction performance for target BPs. Under the optimized conditions, the developed on-line in-tube SPME-HPLC method exhibited low limits of detection (LODs) (0.030-0.055 ng mL^-1). The spiked recoveries were between 85.4 % and 111.8 %, and the relative standard deviations (RSDs) were less than 3.5 % for all the analytes. The results showed that the proposed method provided alternative for the analysis of BPs in complex samples.

3D printing for the integration of porous materials into miniaturised fluidic devices: A review

Porous materials facilitate the efficient separation of chemicals and particulate matter by providing selectivity through structural and surface properties and are attractive as sorbent owing to their large surface area. This broad applicability of porous materials makes the integration of porous materials and microfluidic devices important in the development of more efficient, advanced separation platforms. Additive manufacturing approaches are fundamentally different to traditional manufacturing methods, providing unique opportunities in the fabrication of fluidic devices. The complementary 3D printing (3DP) methods are each accompanied by unique opportunities and limitations in terms of minimum channel size, scalability, functional integration and automation. This review focuses on the developments in the fabrication of 3DP miniaturised fluidic devices with integrated porous materials, focusing polymer-based methods including fused filament fabrication (FFF), inkjet 3D printing and digital light projection (DLP). The 3DP methods are compared based on resolution, scope for multimaterial printing and scalability for manufacturing. As opportunities for printing pores are limited by resolution, the focus is on approaches to incorporate materials with sub-micron pores to be used as membrane, sorbent or stationary phase in separation science using Post-Print, Print-Pause-Print and In-Print processes. Technical aspects analysing the efficiency of the fabrication process towards scalable manufacturing are combined with application aspects evaluating the separation and/or extraction performance. The review is concluded with an overview on achievements and opportunities for manufacturable 3D printed membrane/sorbent integrated fluidic devices.

Monolith/aminated graphene oxide composite-based electric field-assisted solid phase microextraction for efficient capture of phenoxycarboxylic acids herbicides in environmental waters

Efficient capture of strongly polar, ionizable and trace phenoxycarboxylic acids herbicides (PCAHs) from aqueous samples is essential and challenging for environmental monitoring. In the present work, electric field-assisted solid-phase microextraction (EFA-SPME) based on monolith/aminated graphene oxide composite was developed for the first time to efficiently extract trace PCAHs prior to HPLC-tandem mass spectrometry (HPLC-MS/MS) quantification. First, poly (1-allyl-3-methylimidazole difluoromethanesulfonylamide salt-co-divinylbenzene/ethylene dimethacrylate) monolith/aminated graphene oxide composite (MAC) was prepared on the surface of stainless steel wire and employed as the extraction phase of SPME. After that, the MAC-based fiber and a stainless steel wire were connected to a DC power supply that allowed the implement of variable electric fields during adsorption and desorption processes. Various key factors influencing the extraction performance were inspected in detailed. Results well evidenced that the exertion of electric fields improved the enrichment performance, accelerated the trap and release procedures. The proposed MAC/EFA-SPME-HPLC-MS/MS method achieved wide linear ranges (0.005-50.0 μg/L), low limits of detection (0.54-1.3 ng/L) and good precision (2.7-7.0%) for the quantification of PCAHs. The related extraction mechanism was deduced. Additional, the current approach was successfully applied to monitor studied PCAHs at trace contents in environment waters, and the accuracy was confirmed by confirmatory experiments.

Graphene oxide-octadecylsilane incorporated monolithic nano-columns with 50 μm id and 100 μm id for small molecule and protein separation by nano-liquid chromatography

In this study, graphene oxide-octadecylsilane incorporated monolithic nano-columns were developed for protein analysis by nano liquid chromatography (nano LC). The monolithic column with 100 μm id was first prepared by an in situ polymerization using ethylene dimethacrylate (EDMA), 3-chloro-2-hydroxypropylmethacrylate (HPMA-Cl), and methacryloyl graphene oxide nanoparticles (MGONPs). MGONPs were synthesized by the treatment of 3-(trimethoxysilyl)propylmethacrylate (TMSPM) and GO. Tetrahydrofuran (THF) and dodecanol were used as the porogenic solvent. The resulting column was functionalized by dimethyloctadecylch lorosilane (DODCS) for the enhancement of hydrophobicity. The functionalization greatly improved the baseline separation of hydrophobic compounds such as polyaromatic hydrocarbons (PAHs). The optimized monolith with respect to total polymerization mixture was characterized by using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) X-ray diffraction (XRD) and chromatographic analyses. The blank monoliths without functionalization exhibited poor separation while a good separation performance of MGONPs functionalized monoliths was achieved. The monolith with 100 μm id was evaluated in protein separation in nano LC using RNase A, Cytochrome C, Lysozyme, Trypsin, and Ca isozyme II as the test proteins. It was shown that protein separation mechanism was based on large π-system of GO and hydrophobicity of the monolithic structure. Theoretical plates number up to 57 600 plates were achieved. The nano-column with 50 μm id was also prepared using the same polymerization mixture under the same chemical conditions. These nano-columns were employed for protein separation by nano LC, and the dependence of both nano-column performance on the internal diameter was also discussed.

Towards highly specific aptamer-affinity monolithic column by efficient UV light-initiated polymerization in "one-pot"

Time-consuming or tedious operation in multiple-step process might is the obstacle for efficiently preparing aptamer-affinity monolithic column. Here, a new and facile strategy to prepare aptamer-based hybrid affinity monolith in "one-pot" at room temperature was exploited, in which UV light-initiated free-radical polymerization and "thiol-ene" click reaction were implemented simultaneously. Only 7 min was cost for finishing the polymerization reaction, which was only 1/100 of that for the traditional thermal polymerization. Using ochratoxin A (OTA) as the model analyte, the recipe for photo-initiated polymerization was optimized, and SEM morphology, FTIR, EDS, pore size distribution and specific recognition performance were also studied. Compared with traditional thermal polymerization, the resultant monolith was achieved more facilely and displayed better results such as more homogeneous skeleton structure, higher reaction efficiency of aptamer (>88.2%) and better specific selectivity to OTA. Besides, an extremely low nonspecific adsorption of analogues was obtained and showed a level at only 1/25 of that in the similar aptamer-affinity monolith prepared by thermal polymerization. Applied to beer and red wine samples, good recovery yields about 99.7 ± 4.0% -101.2 ± 2.3% (n = 3)was achieved with the acceptable RSDs. It would open up a rapid and promising access to efficiently preparing high-performance aptamer-based affinity monolithic columns for online specific recognition.

Macroporous Polymer Monoliths in Thin Layer Format

Nowadays, macroporous polymer monoliths represent widely used stationary phases for a number of dynamic interphase mass exchange processes such as high-performance liquid chromatography, gas chromatography, electrochromatography, solid-phase extraction, and flow-through solid-state biocatalysis. This review represents the first summary in the field of current achievements on the preparation of macroporous polymer monolithic layers, as well as their application as solid phases for thin-layer chromatography and different kinds of microarray.

Macroporous Polymer Monoliths for Affinity Chromatography and Solid-Phase Enzyme Processing

Nowadays, monolithic stationary phases, because of their special morphology and enormous permeability, are widely used for the development and realization of fast dynamic and static processes based on the mass transition between liquid and solid phases. These are liquid chromatography, solid-phase synthesis, microarrays, flow-through enzyme reactors, etc. High-performance liquid chromatography on monoliths, including the bioaffinity mode, represents unique technique appropriate for fast and efficient separation of biological (macro)molecules of different sizes and shapes (proteins, nucleic acids, peptides), as well as such supramolecular systems as viruses.In the edited chapter, the examples of the application of commercially available macroporous monoliths for modern affinity processing are presented. In particular, the original methods developed for efficient isolation and fractionation of monospecific antibodies from rabbit blood sera, the possibility of simultaneous affinity separation of protein G and serum albumin from human serum, the isolation of recombinant products, such as protein G and tissue plasminogen activator, respectively, are described in detail. The suggested and realized multifunctional fractionation of polyclonal pools of antibodies by the combination of several short monolithic columns (disks) with different affinity functionalities stacked in the same cartridge represents the original and practically valuable method that can be used in biotechnology. In addition, macroporous monoliths were adapted to the immobilization of such different enzymes as polynucleotide phosphorylase, ribonuclease A, α-chymotrypsin, chitinolytic biocatalysts, β-xylosidase, and β-xylanase. The possibility of use of immobilized enzyme reactors based on monoliths for different purposes is demonstrated.

Flow-through enzymatic reactors using polymer monoliths: From motivation to application

The application of monolithic materials as carriers for enzymes has rapidly expanded to the realization of flow-through analysis and bioconversion processes. This expansion is partly attributed to the absence from diffusion limitation in many monoliths-based enzyme reactors. Particularly, the relatively ease of introducing functional groups renders polymer monoliths attractive as enzyme carriers. After summarizing the motivation to develop enzymatic reactors using polymer monoliths, this review reports the most recent applications of such reactors. Besides, the present review focuses on the crucial characteristics of polymer monoliths affecting the immobilization of enzymes and the processing parameters dictating the performance of the resulting enzymatic reactors. This review is intended to provide a guideline for designing and applying flow-through enzymatic reactors using polymer monoliths.

Molding-type Solid-phase Extraction Media Glued with Commercially Available Adhesives

The handling of a particulate sorbent for solid-phase extraction is often troublesome because it causes static clinging and scattering. To overcome this problem, a production method for a simple molding-type solid-phase extraction medium (M-SPEM) was developed in this study by using commercially available adhesives. The content of a particulate sorbent can increase to as much as 85 wt% in the M-SPEM. Because of the high content, the proposed M-SPEMs have a higher specific surface area than previous monolithic media.

Preparation of restricted access monolithic tip via unidirectional freezing and atom transfer radical polymerization for directly extracting magnolol and honokiol from rat plasma followed by liquid chromatography analysis

In the present study, a novel strategy based on unidirectional freezing and atom transfer radical polymerization combined with activator regenerated by electron transfer (ARGET-ATRP) was applied to synthesizing orderly macroporous monolithic column with restricted-access (RA) property in a 1000μL pipette tip. The RA column was composed of hydrophobic inner column (poly(styrene-co-ethylene glycol dimethacrylate) and hydrophilic outer layer (poly-hydroxyethyl methacrylate chain) which was grafted on the hydrophobic surface by means of the second ARGET-ATRP reaction. The as-prepared RA monolithic tip was connected to a 2mL syringe for directly extracting magnolol and honokiol from rat plasma just by manually pushing operation. The surface morphology and chemical composition of the column were characterized by scanning electronic microscope, infrared spectroscopy and X-ray photoelectron spectroscopy respectively. The determined results of evaluation experiments based on the optimized solid phase extraction conditions showed that the RA column possessed good protein exclusion power, extraction recovery and reusability. The constructed RA-SPE-HPLC/UV method for simultaneously analyzing magnolol and honokiol in rat plasma was validated with quality control (QC) samples at four concentration levels. Good precision (RSDs, 3.39~11.16%) and acceptable accuracy (relative recoveries, 89.52%~108.42%) were obtained for intra- and inter-day assays. The determined results of real rat plasma as well as the standard-addition samples demonstrated the developed method with good accuracy and precision. It can be extrapolated from the experimental results that this simple and cost-efficient RA-SPE method is also suitable for directly extracting other hydrophobic constituents in biological body fluid for therapeutic drug monitoring or pharmacokinetic study.

Tunable Polymeric Scaffolds for Enzyme Immobilization

The number of methodologies for the immobilization of enzymes using polymeric supports is continuously growing due to the developments in the fields of biotechnology, polymer chemistry, and nanotechnology in the last years. Despite being excellent catalysts, enzymes are very sensitive molecules and can undergo denaturation beyond their natural environment. For overcoming this issue, polymer chemistry offers a wealth of opportunities for the successful combination of enzymes with versatile natural or synthetic polymers. The fabrication of functional, stable, and robust biocatalytic hybrid materials (nanoparticles, capsules, hydrogels, or films) has been proven advantageous for several applications such as biomedicine, organic synthesis, biosensing, and bioremediation. In this review, supported with recent examples of enzyme-protein hybrids, we provide an overview of the methods used to combine both macromolecules, as well as the future directions and the main challenges that are currently being tackled in this field.

3D-Printed Column with Porous Monolithic Packing for Online Solid-Phase Extraction of Multiple Trace Metals in Environmental Water Samples

In this study, we used a multimaterial three-dimensional printing (3DP) technology and porous composite filaments (Lay-Fomm, Gel-Lay, and Lay-Felt) to fabricate solid phase extraction (SPE) columns for the enhanced extraction of multiple metal ions. When employed as sample pretreatment devices in an automatic flow injection analysis/inductively coupled plasma mass spectrometry (ICP-MS) system, these 3D-printed SPE columns performed the near-complete extractions of Mn, Co, Ni, Cu, Zn, Cd, and Pb ions from natural water samples prior to ICP-MS determination. After optimizing the column fabrication, the extraction conditions, and the automatic analysis system, the column packed with the porous composite Lay-Fomm 40 was found to provide the highest extraction performance-the extraction efficiencies of the listed metal ions were all greater than 99.2%, and the detection limits of the method ranged from 0.3 to 6.7 ng L^-1. The detection of these metal ions in several reference materials (CASS-4, SLEW-3, 1640a, and 1643f) validated the reliability of this method; spike analyses of collected water samples (groundwater, river water, and seawater) demonstrated the applicability of the method. The nature of the printing materials enhanced the analytical performance of 3D-printed sample pretreatment devices. Such approaches will be useful to diversify the range of sample preparation schemes and analytical methods enabled by 3DP technologies.

Extraction of β-blockers from urine with a polymeric monolith modified with 1-allyl-3-methylimidazolium chloride in spin column format

A glycidyl methacrylate-based monolith was modified with imidazolium-based ionic liquid (IL) to be used as stationary phase for solid-phase extraction (SPE). The host monolithic support was prepared by in-situ UV polymerization in spin column format. Two approaches were developed to incorporate the IL into the polymeric monolithic matrix: generation of IL onto the surface monolith, and copolymerization by addition of the IL to the polymerization mixture, which gave the best results. The resulting sorbent materials were morphologically characterized and used for the isolation of five β-blockers from human urine samples. All SPE steps were accomplished by centrifugation, which reduces significantly costs and time in sample treatment. Under optimal conditions, β-blockers were quantitatively retained in the modified monolith at pH 12, and desorbed with a water-methanol mixture, to be subsequently determined via HPLC with UV detection. The limits of detection ranged between 1.4 and 40 μg L^-1, and the reproducibility among extraction units (expressed as relative standard deviation) was below 8.2%. The novel phase was successfully applied to the extraction of propranolol in urine samples with recoveries above 90%.

Simulative Minimization of Mass Transfer Limitations Within Hydrogel-Based 3D-Printed Enzyme Carriers

In biotechnology, immobilization of functional reactants is often done as a surface immobilization on small particles. Examples are chromatography columns and fixed-bed reactors. However, the available surface for immobilization is directly linked to particle diameter and bed porosity for these systems, leading to high backpressure for small particle sizes. When larger molecules, such as enzymes are immobilized, physical entrapment within porous materials like hydrogels is an alternative. An emerging technique for the production of geometrically structured, three-dimensional and scalable hollow bodies is 3D-printing. Different bioprinting methods are available to produce structures of the desired size, resolution and solids content. However, in case of entrapped enzymes mass transfer limitations often determine the achievable reactivities. With increasing complexity of the system, for example a fixed-bed reactor, 3D-simulation is indispensable to understand the local reaction conditions to be able to highlight the optimization potential. Based on experimental data, this manuscript shows the application of the dimensionless numbers effectiveness factor and Thiele modulus for the design of a 3D-printed flow-through reactor. Within the reactor, enzymes are physically entrapped in 3D-printed hydrogel lattices. The local reaction rate of the enzymes is directly dependent on the provided substrate amount at the site of reaction which is limited by the diffusion properties of the hydrogel matrix and the diffusion distance. All three parameters can be summed up by one key figure, the Thiele modulus, which, in short, quantifies mass transfer limitations of a catalytic system. Depending on the rate of the enzymatic reaction in correlation to the diffusional transport, mass transfer limitations will shift the optimum of the system, favoring slow enzyme kinetics and small diffusion distances. Comparison with the enzymatic reaction rate in solution yields the effectiveness factor of the system. As a result, the optimization potential of varying the 3D-printed geometries or the reaction rate within the experimentally available design space can be estimated.

Multiple Zones Modification of Open Off-Stoichiometry Thiol-Ene Microchannel by Aptamers: A Methodological Study & A Proof of Concept

Off-stoichiometry thiol-ene polymer (OSTE) is an emerging thermoset with interesting properties for the development of lab-on-a-chip (LOAC), such as easy microfabrication process, suitable surface chemistry for modification and UV-transparency. One of the challenges for LOAC development is the integration of all the analytical steps in one microchannel, and particularly, trace level analytes extraction/preconcentration steps. In this study, two strategies for the immobilization of efficient tools for this purpose, thiol-modified (C3-SH) aptamers, on OSTE polymer surfaces were developed and compared. The first approach relies on a direct UV-initiated click chemistry reaction to graft thiol-terminated aptamers on ene-terminated OSTE surfaces. The second strategy consists of the immobilization of thiol-terminated aptamers onto OSTE substrates covered by gold nanoparticles. The presence of an intermediate gold nanoparticle layer on OSTE has shown great interest in the efficient immobilization of aptamers, preserving their interaction with the target, and preventing non-specific adsorption. With this second innovative strategy, we proved, for the first time the concept of creating multiple functional zones for sample treatment in an open OSTE-microchannel thanks to the immobilization of aptamers in consecutive areas by the simple droplet deposition methodology. This methodological development allows further consideration of OSTE material for lab-on-a-chip designs, integrating multiple zones for sample pretreatment, based on molecular recognition by ligands, such as aptamers, in a specific zone of the microchannel and is adaptable to a large range of analytical applications for LOAC industrialization.

Eco-friendly production of metal nanoparticles immobilised on organic monolith for pepsin extraction

Polymer monoliths modified by using nanoparticles (NPs) integrate high NP specific surface area with different monolith surface chemistry and high porosity. As a result, they have extensive applications within different fields, whereas nanomaterial-functionalised porous polymer monoliths have elicited considerable interest from investigators. This study is aimed at fabricating organic polymer-based monoliths from polybutyl methacrylate-co-ethylenedimethacrylate (BuMA-co-EDMA) monoliths prior to immobilization of gold or silver metal on the pore surface of the monoliths using reducing reagent (extracts of lemon peels). This was intended to denote a sustainable technique of immobilizing nanoparticles that are advantageous over physical and chemical techniques because it is safe in terms of handling, readily available, environmentally friendly, and cheap. Two different methods were used in the study to effectively immobilize nanoparticles on monolithic components. The outcomes showed that soaking the monolith rod in the prepared nano solution directly and placing it within ovens at temperatures of 80°C constituted the most effective method. Characterisation of the fabricated monolith was undertaken using SEM/EDX analysis, UV-vis. spectra analysis, and visual observation. The SEM analysis showed that nanoparticles were extensively immobilised on the surface polymers. Another peak was attained through EDX analysis, thus confirming the Au atom existence at 2.83% alongside another peak that proved the Ag atom existence at 1.92%. The fabricated components were used as sorbents for purifying protein. The ideal performance was achieved using gold nanoparticles (GNPs) immobilised organic monolith that attained a greater pepsin extraction recovery compared to silver nanoparticles (SNPs) immobilised organic monoliths alongside bare organic-based monolith.