Enhancement anti-interference ability of photoelectrochemical sensor via differential molecularly imprinting technique demonstrated by dopamine determination

Molecularly imprinted polymer photoelectrochemical sensor for the detection of triazophos in water based on carbon quantum dot-modified titanium dioxide

Widely used organophosphorus pesticide triazophos (TAP) can easily cumulate in aquatic system due to its high stability chemically and photochemically and thus posing significant threat to aquatic creatures and humans' health. Urging demand for rapid determining TAP in water has risen. Photoelectrochemical (PEC) sensing turns out to be a good candidate for its simplicity in fabrication and swiftness in detection. Nevertheless, traditional PEC sensors often lack selectivity as their signal generation primarily relies on the oxidation of organic compounds in the electrolyte by photo-induced holes. To address this limitation, molecularly imprinted polymers (MIPs) can be in combined with PEC sensors to significantly enhance the selectivity. Here, we present a novel approach utilizing a PEC sensor enhanced by carbon-modified titanium dioxide molecularly imprinted polymers (MIP/C/TiO2 NTs). Carbon quantum dot (CQD) modification of titanium dioxide nanotube arrays (C/TiO2 NTs) was achieved through a one-step anodization process, effectively enhancing visible light absorption by narrowing the band gap of TiO2, and CQDs also function as sensitizer accelerating charge transfer for improved and stable photocurrent signals during detection. Our method further incorporates MIPs to heighten the selectivity of the PEC sensor. Electro-polymerization using cyclic voltammetry was employed to polymerize MIPs with pyrrole as the functional monomer and triazophos as the target molecule. The resultant MIP/C/TiO2 NT sensor exhibited remarkable sensitivity, with a detection limit of 0.03 nM (S/N = 3), alongside exceptional selectivity and stability for triazophos detection in water. This offers a promising avenue for efficient, cost-effective, and rapid monitoring of pesticide contaminants in aquatic environments, contributing to the broader goals of environmental preservation and public health.

Wavelength-dependent photoelectrochemical response demonstrated by the determination of acetaminophen and rutin in differential molecularly imprinted polymers strategy

Herein, the excitation wavelength-dependent responses of the molecularly imprinted polymer (MIP) photoelectrochemical (PEC) sensors were investigated, using acetaminophen (AP), rutin (RT) and perfluorooctanoate (PFOA) as the model templates, pyrrole as functional monomer, CuInS2@ZnS/TiO2 NTs as the basic photoelectrode. With wavelength λ > 240 nm, the photocurrent of MIPPFOA enhanced at higher concentrations of PFOA. With increasing AP concentration, the photocurrents of MIPAP could decline with λ < 271 nm, not change at λ = 270 nm, or increase with λ > 270 nm. As RT concentration increased, the photocurrents of MIPRT could decrease (λ < 431 nm), not change (λ = 431 nm) or increase (λ > 431 nm). The PEC responses depend on the comprehensive interaction of two contrary mechanisms from the template molecules within the MIP membrane. The photocurrent is enhanced by the role of the electron donor for photo-generated holes but attenuated due to the steric hindrance effect and the excitation light intensity loss via absorption or scattering. The apparent molar absorption coefficient of AP and RT within MIP membranes are 9.1-19.4 folds of those measured from dilute solutions. By using a routine UV lamp as the light source, the photocurrents of MIPRT at 254 nm and MIPAP at 365 nm were used to determine RT and AP, with the detection limits of 5.3 and 16 nM, respectively. The interference from the non-specific adsorption of interferents on the surfaces of MIPAP and MIPRT was reduced by one order of magnitude via a differential strategy.

A novel differential ratiometric molecularly imprinted electrochemical sensor for determination of sulfadiazine in food samples

Herein, we report a novel differential ratiometric molecularly imprinted polymer (MIP) electrochemical sensor for sulfadiazine (SDZ). An MIP membrane with double templates, SDZ and propyl gallate (PG), was fabricated on glassy carbon electrode (GCE) modified by CuInS2/ZnS nanocomposites. After adding PG in the samples as the reference, the current differences between MIP@CuInS2/ZnS/GCE and non-imprinted polymer@CuInS2/ZnS/GCE at the potentials of 0.18 V (ΔIPG) and 0.92 V (ΔISDZ) were measured. The ratio of ΔISDZ/ΔIPG was used for SDZ determination in the differential and ratiometric dual-mode. The influence of the variations in electrode modification and sample enrichment conditions on the determination of SDZ can be suppressed by 2.8 ∼ 13.2-fold, enhancing the reproducibility and stability of the MIP sensor. The interference level was reduced by one order of magnitude compared with the normal MIP mode. The proposed sensors were used to determine SDZ in food samples, with the detection limit of 2.1 nM.

A differential strategy to enhance the anti-interference ability of molecularly imprinted electrochemiluminescence sensor with a semi-logarithmic calibration curve

The non-specific adsorption behaviors of various interferents on the surface of a molecularly imprinted polymer (MIP) are adverse for the selectivity of an MIP-based sensor, which can be overcome via a differential strategy by using the differential signal between MIP- and non-imprinted polymer (NIP)-based sensors. However, the normal differential mode is not suitable for the MIP-based sensors with non-linear calibration curves. Herein, an improved differential strategy is reported for an MIP-based sensor with a semi-logarithmic calibration curve, demonstrated by an electrochemiluminescence (ECL) sensor for dopamine (DA). Glassy carbon electrode (GCE) was modified by the mixture of g-C3N4, TiO2 nanoparticles (NPs) and carbon nanotubes (CNTs). MIP membrane for DA was fabricated on the surface of g-C3N4/TiO2NPs/CNTs/GCE using chitosan for film-forming, obtained MIP@GCE. To enhance the anti-interference ability of the MIP-based DA sensor, the difference between exponential functions ECL intensities of MIP@GCE and NIP@GCE is used as the analytical signal in the improved differential strategy. The differential signal was increased linearly with increasing DA concentration ranging from 10 pM to 0.10 μM, with the detection limit of 5.6 pM. The interference level of Cu2+ on DA determination in the improved differential mode is only 9.7% of that in the normal MIP mode. The improved differential strategy can be used in other MIP-based sensors with semi-logarithmic calibration curves.

Molecularly imprinted ultrasensitive cholesterol photoelectrochemical sensor based on perfluorinated organics functionalization and hollow carbon spheres anchored organic-inorganic perovskite

In spite of organic-inorganic perovskite emerging as a novel efficient light-harvesting material owing to their superior optical properties, excitonic properties, and electrical conductivity, the related applications are severely limited for their poor stability and selectivity. Herein, we introduced hollow carbon spheres (HCSs) and 2-(perfluorohexyl) ethyl methacrylate (PFEM) based molecularly imprinted polymers (MIPs) to dual-functionalize CH3NH3PbI3. HCSs can provide perovskite load conditions, passivate perovskite defects, increase carrier transport and effectively improve its hydrophobicity. The perfluorinated organic compound based MIPs film can not only enhance the water and oxygen stability of perovskite, but also endow it specific selectivity. Moreover, it can reduce the photoexcited electron-hole pair recombination and prolong the electron lifetime. Benefiting from the synergistic sensitization of HCSs and MIPs, an ultrasensitive photoelectrochemical platform (MIPs@CH3NH3PbI3@HCSs/ITO) for cholesterol sensing was acquired with a very wide linear range of 5.0 × 10-14-5.0 × 10-8 mol/L and an extremely low detection limit of 2.39 × 10-15 mol/L. The designed PEC sensor exhibited good selectivity and stability, as well as practicality for real sample analysis. The present work extended the development of the high-performance perovskite and showed its broad application prospect for advanced PEC construction.

Au/TiO2-based molecularly imprinted photoelectrochemical sensor for dibutyl phthalate detection

A photoelectrochemical molecular imprinting sensor based on Au/TiO₂ nanocomposite was constructed for the detection of dibutyl phthalate. Firstly, TiO₂ nanorods were grown on fluorine-doped tin oxide substrate by hydrothermal method. Then, gold nanoparticles were electrodeposited on TiO₂ to fabricate Au/TiO₂. Finally, molecular imprinted polymer was electropolymerized on the Au/TiO₂ surface to construct MIP/Au/TiO₂ PEC sensor for DBP. The conjugation effect of MIP accelerates the electron transfer between TiO₂ and MIP, which can greatly improve the photoelectric conversion efficiency and sensitivity of the sensor. In addition, MIP can also provide sites for highly selective recognition of dibutyl phthalate molecules. Under optimal experimental conditions, the prepared photoelectrochemical sensor was used for the quantitative determination of DBP and the results showed a wide linear range (50 to 500 nM), a low limit of detection (0.698 nM), and good selectivity. The sensor was used in a study of real water samples to show that it has promising applications in environmental analysis.

Electrochemically Deposited Molecularly Imprinted Polymer-Based Sensors

This review is dedicated to the development of molecularly imprinted polymers (MIPs) and the application of MIPs in sensor design. MIP-based biological recognition parts can replace receptors or antibodies, which are rather expensive. Conducting polymers show unique properties that are applicable in sensor design. Therefore, MIP-based conducting polymers, including polypyrrole, polythiophene, poly(3,4-ethylenedioxythiophene), polyaniline and ortho-phenylenediamine are frequently applied in sensor design. Some other materials that can be molecularly imprinted are also overviewed in this review. Among many imprintable materials conducting polymer, polypyrrole is one of the most suitable for molecular imprinting of various targets ranging from small organics up to rather large proteins. Some attention in this review is dedicated to overview methods applied to design MIP-based sensing structures. Some attention is dedicated to the physicochemical methods applied for the transduction of analytical signals. Expected new trends and horizons in the application of MIP-based structures are also discussed.

A Novel Photoelectrochemical Aptamer Sensor Based on CdTe Quantum Dots Enhancement and Exonuclease I-Assisted Signal Amplification for Listeria monocytogenes Detection

To achieve the rapid detection of Listeria monocytogenes, this study used aptamers for the original identification and built a photoelectrochemical aptamer sensor using exonuclease-assisted amplification. Tungsten trioxide (WO3) was used as a photosensitive material, was modified with gold nanoparticles to immobilize complementary DNA, and amplified the signal by means of the sensitization effect of CdTe quantum dots and the shearing effect of Exonuclease I (Exo I) to achieve high-sensitivity detection. This strategy had a detection limit of 45 CFU/mL in the concentration range of 1.3 × 101-1.3 × 107 CFU/mL. The construction strategy provides a new way to detect Listeria monocytogenes.

Molecularly imprinted polymer-enhanced biomimetic paper-based analytical devices: A review

The popularization of paper-based analytical devices (PADs) in analytical science has fostered research on enhancing their analytical performance for accurate and sensitive assays. With their superb recognition capability and structural stability, molecularly imprinted polymers (MIPs) have been extensively employed as biomimetic receptors for capturing target analytes in various complex matrices. The integration of MIPs as recognition elements with PADs (MIP-PADs) has opened new opportunities for advanced analytical devices with elevated selectivity and sensitivity, as well as a shorter assay time and a lower cost. This review covers recent advances in MIP-PAD fabrication and engineering based on multifarious signal transduction systems such as colorimetry, fluorescence, electrochemistry, photoelectrochemistry, and chemiluminescence. The application of MIP-PADs in the fields of biomedical diagnostics, environmental analysis, and food safety monitoring is also reviewed. Further, the advantages, challenges, and perspectives of MIP-PADs are discussed.