Spatio-temporal evolution of hydroxyapatite crystal thickness at the bone-implant interface

Sheep Bone Ultrastructure Analyses Reveal Differences in Bone Maturation around Mg-Based and Ti Implants

Magnesium alloys are some of the most convenient biodegradable materials for bone fracture treatment due to their tailorable degradation rate, biocompatibility, and mechanical properties resembling those of bone. Despite the fact that magnesium-based implants and ZX00 (Mg-0.45Zn-0.45Ca in wt.%), in particular, have been shown to have suitable degradation rates and good osseointegration, knowledge gaps remain in our understanding of the impact of their degradation properties on the bone's ultrastructure. Bone is a hierarchically structured material, where not only the microstructure but also the ultrastructure are important as properties like the local mechanical response are determined by it. This study presents the first comparative analysis of bone ultrastructure parameters with high spatial resolution around ZX00 and Ti implants after 6, 12, and 24 weeks of healing. The mineralization was investigated, revealing a significant decrease in the lattice spacing of the (002) Bragg's peak closer to the ZX00 implant in comparison to Ti, while no significant difference in the crystallite size was observed. The hydroxyapatite platelet thickness and osteon density demonstrated a decrease closer to the ZX00 implant interface. Correlative indentation and strain maps obtained by scanning X-ray diffraction measurements revealed a higher stiffness and faster mechanical adaptation of the bone surrounding Ti implants as compared to the ZX00 ones. Thus, the results suggest the incorporation of Mg2+ ions into the bone ultrastructure, as well as a lower degree of remodeling and stiffness of the bone in the presence of ZX00 implants than Ti.

Effect of collagen fibril orientation on the anisotropic properties of peri-implant bone

In orthopedic and dental surgery, the implantation of biomaterials within the bone to restore the integrity of the treated organ has become a standard procedure. Their long-term stability relies on the osseointegration phenomena, where bone grows onto and around metallic implants, creating a bone-implant interface. Bone is a highly hierarchical material that evolves spatially and temporally during this healing phase. A deeper understanding of its biomechanical characteristics is needed, as they are determinants for surgical success. In this context, we propose a multiscale homogenization model to evaluate the effective elastic properties of bone as a function of the distance from the implant, based on the tissue's structure and composition at lower scales. The model considers three scales: hydroxyapatite foam (nanoscale), ultrastructure (microscale), and tissue (mesoscale). The elastic properties and the volume fraction of the elementary constituents of bone matrix (mineral, collagen, and water), the orientation of the collagen fibril relative to the implant surface, and the mesoscale porosity constitute the input data of the model. The effect of a spatiotemporal variation in the collagen fibrils' orientation on the bone anisotropic properties in the proximity of the implant was investigated. The findings revealed a strong variation of the components of the effective elasticity tensor of the bone as a function of the distance from the implant. The effective elasticity appears to be primarily sensitive to the porosity (mesoscale) rather than to the collagen fibrils' orientation (sub-micro scale). However, the orientation of the fibrils has a significant influence on the isotropy of the bone. When analyzing the symmetry properties of the effective elasticity tensor, the ratio between the isotropic and hexagonal components is determined by a combination of the porosity and the fibrils' orientation. A decrease in porosity leads to a decrease in bone isotropy and, in turn, an increase in the impact of the fibrils' orientation. These results demonstrate that the collagen fibril orientation should be taken into account to properly describe the effective elastic anisotropy of bone at the organ scale.

Towards Polycaprolactone-Based Scaffolds for Alveolar Bone Tissue Engineering: A Biomimetic Approach in a 3D Printing Technique

The alveolar bone is a unique type of bone, and the goal of bone tissue engineering (BTE) is to develop methods to facilitate its regeneration. Currently, an emerging trend involves the fabrication of polycaprolactone (PCL)-based scaffolds using a three-dimensional (3D) printing technique to enhance an osteoconductive architecture. These scaffolds are further modified with hydroxyapatite (HA), type I collagen (CGI), or chitosan (CS) to impart high osteoinductive potential. In conjunction with cell therapy, these scaffolds may serve as an appealing alternative to bone autografts. This review discusses research gaps in the designing of 3D-printed PCL-based scaffolds from a biomimetic perspective. The article begins with a systematic analysis of biological mineralisation (biomineralisation) and ossification to optimise the scaffold's structural, mechanical, degradation, and surface properties. This scaffold-designing strategy lays the groundwork for developing a research pathway that spans fundamental principles such as molecular dynamics (MD) simulations and fabrication techniques. Ultimately, this paves the way for systematic in vitro and in vivo studies, leading to potential clinical applications.

Efficiency of Nanohydroxyapatite on Repairing Type II Diabetes Dental Implant-Bone Defect

The purpose of this study was to see how a nanohydroxyapatite (n-HA) composite polyamide 66 (PA66) affected the repair of bone defects in diabetics with titanium implants, as well as to develop experimental materials for the creation of the interface between bone tissue and titanium implants. Rabbit bone marrow mesenchymal stem cells (MSCs) were isolated using n-HA/PA66 composite material, and the effect of coculture with the material on cell proliferation was analyzed after induction of mineralization. Bone defect models of diabetic experimental rabbits and titanium implants were prepared. Normal rabbits with bone defects were used as control (NC group, N = 8). After the diabetic bone defect (DM group, N = 8) and the implantation of n-HA/PA66 composite material (n-HA/PA66 group, N = 8), the differences in body weight, blood glucose, scanning electron microscopy of the implant-bone interface, bone mineral density, new bone trabecular parameters, histomorphology, and biomechanical properties of the implant-bone interface were compared and analyzed. In vitro test results showed that MSC cell growth could be promoted by mineralization induction, the cell growth condition was good after coculture with n-HA/PA66, and the proliferation activity of MSCs was not affected by the material. In vivo test results showed that the body weight of the DM group and n-HA/PA66 group was considerably inferior to that of the NC group, and the blood glucose was dramatically superior to that of the NC group (P < 0.05). However, the body weight of the n-HA/PA66 group was dramatically superior to that of the DM group (P < 0.05). The bone mineral density, bone volume fraction (BV/TV), bone surface area fraction (BS/BV), bone trabecular thickness (Tb.Th), bone trabecular number (Tb.N), bone trabecular area, and biomechanical properties in the DM group were considerably inferior to those in the NC group and n-HA/PA66 group (P < 0.05). The trabecular space (Tb.Sp) in the NC group and n-HA/PA66 group was dramatically superior to that in the NC group (P < 0.05). The bone mineral density, BV/TV, BS/BV, Tb.Th, Tb.N, trabecular area, and biomechanical properties of the n-HA/PA66 group were dramatically superior to those of the NC group (P < 0.05), while Tb.Sp was considerably inferior to that of the NC group (P < 0.05). These findings showed that the n-HA/PA66 material had good biocompatibility and minimal cytotoxicity, and that filling the space between the surrounding bone and the titanium implant can enhance bone repair. This research paved the way for future research into the tissue-engineered bone in the field of oral surgery.

A stochastic micro to macro mechanical model for the evolution of bone-implant interface stiffness

Upon placement of an implant into living bone, an interface is formed through which various biochemical, biological, physical, and mechanical interactions take place. This interface evolves over time as the mechanical properties of peri-implant bone increase. Owing to the multifactorial nature of interfacial processes, it is challenging to devise a comprehensive model for predicting the mechanical behavior of the bone-implant interface. We propose a simple spatio-temporally evolving mechanical model - from an elementary unit cell comprising randomly oriented mineralized collagen fibrils having randomly assigned stiffness all the way up to a macroscopic bone-implant interface in a gap healing scenario. Each unit cell has an assigned Young's modulus value between 1.62 GPa and 25.73 GPa corresponding to minimum (i.e., 0) and maximum (i.e., 0.4) limits of mineral volume fraction, respectively, in the overlap region of the mineralized collagen fibril. Gap closure and subsequent stiffening are modeled to reflect the two main directions of peri-implant bone formation, i.e., contact osteogenesis and distance osteogenesis. The linear elastic stochastic finite element model reveals highly nonlinear temporal evolution of bone-implant interface stiffness, strongly dictated by the specific kinetics of contact osteogenesis and distance osteogenesis. The bone-implant interface possesses a small stiffness until gap closure, which subsequently evolves into a much higher stiffness, and this transition is reminiscent of a percolation transition whose threshold corresponds to gap closure. The model presented here, albeit preliminary, can be incorporated into future calculations of the bone-implant system where the interface is well-defined mechanically. STATEMENT OF SIGNIFICANCE: A simple, physically informed model for the mechanical characteristics of the bone-implant interface is still missing. Here, we start by extending the reported mechanical characteristics of a one cubic micrometre unit cell to a 250 µm long interface made of 1 µm thick layers. The stiffness of each cell (based on mineral content) is assigned randomly to mimic bone micro-heterogeneity. The numerical study of this interface representative structure allows for the simultaneous determination of the spatio-temporal evolution of the mechanical response at local (discrete element) and global (overall model) scales. The proposed model is the first of this kind that can easily be incorporated into realistic future models of bone-implant interaction with emphasis on implant stability and different loading conditions.

Neutron microtomography to investigate the bone-implant interface-comparison with histological analysis

Bone properties and especially its microstructure around implants are crucial to evaluate the osseointegration of prostheses in orthopaedic, maxillofacial and dental surgeries. Given the intrinsic heterogeneous nature of the bone microstructure, an ideal probing tool to understand and quantify bone formation must be spatially resolved. X-ray imaging has often been employed, but is limited in the presence of metallic implants, where severe artifacts generally arise from the high attenuation of metals to x-rays. Neutron tomography has recently been proposed as a promising technique to study bone-implant interfaces, thanks to its lower interaction with metals. The aim of this study is to assess the potential of neutron tomography for the characterisation of bone tissue in the vicinity of a metallic implant. A standardised implant with a bone chamber was implanted in rabbit bone. Four specimens were imaged with neutron tomography and subsequently compared to non-decalcified histology to stain soft and mineralised bone tissues, used here as a ground-truth reference. An intensity-based image registration procedure was performed to place the 12 histological slices within the corresponding 3D neutron volume. Significant correlations (p < 0.01) were obtained between the two modalities for the bone-implant contact (BIC) ratio (R = 0.77) and the bone content inside the chamber (R = 0.89). The results indicate that mineralised bone tissue can be reliably detected by neutron tomography. However, theBICratio and bone content were found to be overestimated with neutron imaging, which may be explained by its sensitivity to non-mineralised soft tissues, as revealed by histological staining. This study highlights the suitability of neutron tomography for the analysis of the bone-implant interface. Future work will focus on further distinguishing soft tissues from bone tissue, which could be aided by the adoption of contrast agents.