Time-dependent behavior of porcine periodontal ligament: A combined experimental, numeric in-vitro study

Three-dimensional positions of the center of resistance of the maxillary canine distal movement under orthodontic force loading

Using finite-element analysis, we aimed to determine the center of resistance (CRes) of the maxillary canine for setting orthodontic forces. The inclination of the canine was measured by first loading from the mesial to the distal side of the mesial root surface, then the position and direction of the load that minimized the inclination were investigated. The CRes was defined as the set of midpoints of the minimum distances between two inclination lines. Twenty-one CRes values were calculated from a set of seven lines. These CRes data were then aggregated as a 95% confidence ellipsoid of width 0.170×0.016×0.009 mm with center points 4.269, 0.224, and 4.315 mm in the apical, mesial, and lingual directions from the origin, respectively. Further studies are required to effectively apply the CRes identified in this study to clinical applications.

Construction of Human Periodontal Ligament Constitutive Model Based on Collagen Fiber Content

Periodontal ligament (PDL) is mainly composed of collagen fiber bundles, and the content of collagen fiber is an important factor affecting the mechanical properties of PDL. Based on this, the purpose of this study is to explore the effect of the PDL collagen fiber content on its viscoelastic mechanical behavior. Transverse and longitudinal samples of different regions of PDL were obtained from the human maxilla. The fiber content at different regions of human PDL was quantitatively measured using image processing software, and a new viscoelastic constitutive model was constructed based on the fiber content. The nano-indentation experiment was carried out with a loading rate of 0.5 mN·s-1, a peak load of 3 mN, and a holding time of 200 s, and the model parameters were obtained through the experiment data. The results showed that with the increase of fiber content, the deformation resistance of PDL also increased, and compared with the neck and middle region, the compressive strain in the apical region of PDL was the largest. The range of reduced elastic modulus of human PDL was calculated to be 0.39~5.08 MPa. The results of the experimental data and the viscoelastic constitutive model fit well, indicating that the model can well describe the viscoelastic behavior of human PDL.

In-fiber Bragg sensor measurements assess fluid effects on strain in the periodontal space of an ex-vivo swine incisor complex under mechanical loading

The purpose of this study is to determine whether in-fiber Bragg grating (FBG) sensors detect changes within the periodontal ligament (PDL) of ex-vivo swine tooth-PDL-bone complex (TPBC) when manipulating fluid content. Recording strain will allow for a better understanding of the biomechanics of viscoelastic load transfer from the tooth to the PDL during chewing and/or orthodontic tooth movement, as well as replication of these dynamics in regenerated PDL tissues. FBG sensors placed within the PDL of swine incisor teeth were used to measure strain resulting from an intrusive load. Specimens were mounted in a custom platform within an MTS machine and a compressive load was applied at 0.3 mm/s to a depth of 0.5 mm and held for 10 s. Median peak strain and load and median absolute deviation (MAD) were compared: dry vs. saline (n = 19) with bias-corrected bootstrap 95% CI. Dry vs. saline conditions did not statistically differ (median peaks of 5με, 103-105 N) and recorded strains showed high repeatability (MAD of 0.82με, 0.72με, respectively). FBG sensors did not detect the fluid changes in this study, suggesting that the deformation of tissues in the PDL space collectively determine FBG strain in response to tooth loading. The repeatability of measurements demonstrates the potential for FBG sensors to assess the strain in the PDL space of an in vivo swine model.

Three-dimensional location and distribution of the center of resistance in the maxillary first molar applied to occlusal force

We aimed to investigate the center of resistance (CRes) of the maxillary first molar to set the occlusal force through finite element analysis. The inclination of the molar was measured, with loading to the root on the crown, and the position and direction of the load that minimized the inclination were investigated. The CRes was defined as the set of midpoints of the minimum distances between the two lines. Nine hundred and ninety CRes points were estimated from forty-five lines. The CRes was estimated as the point 1.22 mm (Z), -0.74 mm (X), and 0.23 mm (Y) from the origin in the apical, distal, and buccal side directions, respectively, with an ellipsoid area of 1.578 (Z) mm×0.097 (X) mm×0.100 (Y) mm. Further research is required to make effective use of the CRes identified in this study for clinical applications.

Strain Measurement within an Intact Swine Periodontal Ligament

The periodontal ligament (PDL) provides support, proprioception, nutrition, and protection within the tooth–PDL–bone complex (TPBC). While understanding the mechanical behavior of the PDL is critical, current research has inferred PDL mechanics from finite element models, from experimental measures on complete TPBCs, or through direct measurement of isolated PDL sections. Here, transducers are used in an attempt to quantify ex vivo PDL strain. In-fiber Bragg grating (FBG) sensors are small flexible sensors that can be placed within an intact TPBC and yield repeatable strain measurements from within the PDL space. The objective of this study was to determine: 1) if the FBG strain measured from the PDL space of intact swine premolars ex vivo was equivalent to physical PDL strains estimated through finite element analysis and 2) if a change in FBG strain could be linearly related to a change in finite element strain under variable tooth displacement, applied to an intact swine TPBC. Experimentally, individual TPBCs were subjected to 2 displacements (n = 14). The location of the FBG was determined from representative micro–computed tomography images. From a linear elastic finite element model of a TPBC, the strain magnitudes at the sensor locations were recorded. An experimental ratio (i.e., FBG strain at the first displacement divided by the FBG strain at the second displacement) and a finite element ratio (i.e., finite element strain at the first displacement divided by the finite element strain at the second displacement) were calculated. A linear regression model indicated a statistically significant relationship between the experimental and finite element ratio (P = 0.017) with a correlation coefficient (R²) of 0.448. It was concluded that the FBG sensor could be used as a measure for a change in strain and thus could be implemented in applications where the mechanical properties of an intact PDL are monitored over time.

Three-dimensional finite element analysis of the effect of alveolar cleft bone graft on the maxillofacial biomechanical stabilities of unilateral complete cleft lip and palate

BACKGROUND

The objective is to clarify the effect of alveolar cleft bone graft on maxillofacial biomechanical stabilities, the key areas when bone grafting and in which should be supplemented with bone graft once bone resorption occurred in UCCLP (unilateral complete cleft lip and palate).

METHODS

Maxillofacial CAD (computer aided design) models of non-bone graft and full maxilla cleft, full alveolar cleft bone graft, bone graft in other sites of the alveolar cleft were acquired by processing the UCCLP maxillofacial CT data in three-dimensional modeling software. The maxillofacial bone EQV (equivalent) stresses and bone suture EQV strains under occlusal states were obtained in the finite element analysis software.

RESULTS

Under corresponding occlusal states, the EQV stresses of maxilla, pterygoid process of sphenoid bone on the corresponding side and anterior alveolar arch on the non-cleft side were higher than other maxillofacial bones, the EQV strains of nasomaxillary, zygomaticomaxillary and pterygomaxillary suture on the corresponding side were higher than other maxillofacial bone sutures. The mean EQV strains of nasal raphe, the maximum EQV stresses of posterior alveolar arch on the non-cleft side, the mean and maximum EQV strains of nasomaxillary suture on the non-cleft side in full alveolar cleft bone graft model were all significantly lower than those in non-bone graft model. The mean EQV stresses of bilateral anterior alveolar arches, the maximum EQV stresses of maxilla and its alveolar arch on the cleft side in the model with bone graft in lower 1/3 of the alveolar cleft were significantly higher than those in full alveolar cleft bone graft model.

CONCLUSIONS

For UCCLP, bilateral maxillae, pterygoid processes of sphenoid bones and bilateral nasomaxillary, zygomaticomaxillary, pterygomaxillary sutures, anterior alveolar arch on the non-cleft side are the main occlusal load-bearing structures before and after alveolar cleft bone graft. Alveolar cleft bone graft mainly affects biomechanical stabilities of nasal raphe and posterior alveolar arch, nasomaxillary suture on the non-cleft side. The areas near nasal floor and in the middle of the alveolar cleft are the key sites when bone grafting, and should be supplemented with bone graft when the bone resorbed in these areas.

A hierarchical bilayer architecture for complex tissue regeneration

Engineering a complete, physiologically functional, periodontal complex structure remains a great clinical challenge due to the highly hierarchical architecture of the periodontium and coordinated regulation of multiple growth factors required to induce stem cell multilineage differentiation. Using biomimetic self-assembly and microstamping techniques, we construct a hierarchical bilayer architecture consisting of intrafibrillarly mineralized collagen resembling bone and cementum, and unmineralized parallel-aligned fibrils mimicking periodontal ligament. The prepared biphasic scaffold possesses unique micro/nano structure, differential mechanical properties, and growth factor-rich microenvironment between the two phases, realizing a perfect simulation of natural periodontal hard/soft tissue interface. The interconnected porous hard compartment with a Young's modulus of 1409.00 ± 160.83 MPa could induce cross-arrangement and osteogenic differentiation of stem cells in vitro, whereas the micropatterned soft compartment with a Young's modulus of 42.62 ± 4.58 MPa containing abundant endogenous growth factors, could guide parallel arrangement and fibrogenic differentiation of stem cells in vitro. After implantation in critical-sized complete periodontal tissue defect, the biomimetic bilayer architecture potently reconstructs native periodontium with the insertion of periodontal ligament fibers into newly formed cementum and alveolar bone by recruiting host mesenchymal stem cells and activating the transforming growth factor beta 1/Smad3 signaling pathway. Taken together, integration of self-assembly and microstamping strategies could successfully fabricate a hierarchical bilayer architecture, which exhibits great potential for recruiting and regulating host stem cells to promote synergistic regeneration of hard/soft tissues.

Development and verification of a constitutive model for human periodontal ligament based on finite element analysis

This study aimed to develop a constitutive model for human periodontal ligament (PDL) by combining the hyperelastic and viscosity models. We performed the finite element analysis (FEA) to simulate the experimental processes of the PDL in vitro and in vivo tests to verify the developed model. The FEA results indicated that the simulative curves were consistent with the experimental curves in the PDL in vitro tests. Moreover, for the in vivo measurements, the simulative result of 0.6258 N was similar to the experimental value of 0.65 N. The study results can help orthodontists better understand the biomechanical characteristics of PDL.

Modelling and evaluating periodontal ligament mechanical behaviour and properties: A scoping review of current approaches and limitations

This scoping review is intended to synthesize the techniques proposed to model the tooth-periodontal ligament-bone complex (TPBC), while also evaluating the suggested periodontal ligament (PDL) material properties. It is concentrated on the recent advancements on the PDL and TPBC models, while identifying the advantages and limitations of the proposed approaches. Systematic searches were conducted up to December 2020 for articles that proposed PDL models to assess orthodontic tooth movement in Compendex, Web of Science, EMBASE, MEDLINE, PubMed, ScienceDirect, Google Scholar and Scopus databases. Although there have been many studies focused on the evaluation of PDL material properties through numerous modelling approaches, only a handful of approaches have been identified to investigate the interface properties of the PDL as a complete dynamical system (TPBC models). Past reviews on the analytical and experimental determination of the PDL properties already show a concerning range in reported output values-some nearly six orders of magnitude in difference-that strongly suggested the need for further investigation. Surprisingly, it has not yet been possible to determine a narrower range of values for the PDL material properties. Moreover, very few scientific approaches address the TPBC as an integrated complex system model. In consequence, current methods for capturing the PDL material behaviour in a clinical setting are limited and inconclusive. This synthesis encourages more systematic, pragmatic and phenomenological research in this area.

Tensile creep mechanical behavior of periodontal ligament: A hyper-viscoelastic constitutive model

OBJECTIVE

In orthodontic treatment, the biomechanical response of periodontal ligament (PDL) induces tooth movement. Coupling modeling of PDL can effectively reflect its biomechanical response. The nonlinear creep mechanical behavior of PDL was studied by uniaxial tensile creep test and a new hyper-viscoelastic constitutive model. Two coupling modeling methods with limitations were excluded.

METHODS

PDL specimens were prepared from the central incisors of pig mandible. The theoretical step function was replaced by static loading with a total loading time of 1 s. The creep loading with the constant stresses of 0.05, 0.1, and 0.15 MPa was selected and kept unchanged for 1000 s. The instantaneous hyperelastic mechanical behavior and time-dependent nonlinear viscoelastic mechanical behavior of PDL were characterized by coupled instantaneous third-order Ogden hyperelastic and time-dependent nonlinear creep models.

RESULTS

The results showed that the instantaneous elastic curve of PDL increases in the form of hyperelastic index. The creep strain and creep compliance curves increase rapidly before 200s, and then increase slowly in steady state. The creep strain increased with an increase in the constant stress; conversely, the creep compliance decreased with an increase in the constant stress. The results showed that the experimental data were highly consistent with the hyper-viscoelastic constitutive model (R²>0.97).

SIGNIFICANCE

We normalize the framework of hyper-viscoelastic coupling modeling (Instantaneous hyperelastic model + time-dependent nonlinear viscoelastic model). Which can be extended to other nonlinear viscoelastic biomaterials.

Experimental repeatability, sensitivity, and reproducibility of force and strain measurements from within the periodontal ligament space during ex vivo swine tooth loading

The Periodontal Ligament (PDL) is a complex connective tissue that anchors a tooth to the surrounding alveolar bone. The small size and complex geometry of the PDL space within an intact tooth-PDL-bone complex (TPBC) limits strain measurements. An in-fiber Bragg grating (FBG) sensor offers potential for such measurements due to its small size. This work defines an experimental procedure where strain and force were measured during quasi-static, apically directed, displacement-controlled tests on swine premolar crowns. Specifically, the: inter-TPBC, intra-TPBC, and long-term repeatability after a preconditioned state was objectively identified; sensitivity to preload magnitude, TPBC alignment, and sensor depth; and reproducibility within a TPBC was determined. Data clustering was used to determine the appropriate number of preconditioning trials, ranging from one to seven. Strain and force measurements showed intra-TPBC repeatability with average adjusted root mean square from the median of 28.9% of the peak strain and 4.5% of the peak force measurement. A Mann-Whitney U test generally found statistically significant differences in peak strain and force measurements between the left and right sides, suggesting a lack of inter-TPBC repeatability. Using a Friedman test, it was shown that peak strain measures were sensitive to the TPBC alignment and sensor depth, while peak force measures were sensitive to the preload and TPBC alignment. A Friedman test suggested reproducible strain and force measurements when the FBG was replaced within the same TPBC and the preload, alignment, and sensor depth were controlled.