Cellulose/microalgae composite films prepared in ionic liquids

Sustainable Cross-Linkers for the Synthesis of Cellulose-Based Aerogels: Research and Application

Cellulose aerogels with polyester resin as cross-linkers have attracted much attention. This study describes the route to produce a fully bio-based aerogel with high added value from waste paper and starch, cellulose acetate and starch–cellulose acetate mixture as cross-linkers for oil adsorption, instead of the environmentally harmful polyester resin. The manufacturing process is simple, sustainable and cost-efficient, without releasing harmful by-products into the environment. The effects of different cross-linkers on the oil adsorption, dynamic oil retention, reusability and morphology of the aerogels were studied in detail. Experimental results show that these environmentally friendly recycled aerogels have a very low density, i.e., —0.0110–0.0209 g cm−3, and highly porous structures, with a porosity of 96.74–99.18%. The synthesized hydrophobic aerogels showed contact angles of ∼124–129°. The compression moduli are lower than that of an aerogel with polyester as a cross-linker, but the compression modulus of the mixture of starch and cellulose acetate especially shows a higher value than expected. The sorption capacity of the aerogels with bio-based cross-linkers was significantly increased compared to the aerogels with polyester; it is now up to 56 times their own weight. The aerogels also have good oil-retention properties.

Algal biopolymers as sustainable resources for a net-zero carbon bioeconomy

The era for eco-friendly polymers was ushered by the marine plastic menace and with the discovery of emerging pollutants such as micro-, nano-plastics, and plastic leachates from fossil fuel-based polymers. This review investigates algae-derived natural, carbon neutral polysaccharides and polyesters, their structure, biosynthetic mechanisms, biopolymers and biocomposites production process, followed by biodegradability of the polymers. The review proposes acceleration of research in this promising area to address the need for eco-friendly polymers and to increase the cost-effectiveness of algal biorefineries by coupling biofuel, high-value products, and biopolymer production using waste and wastewater-grown algal biomass. Such a strategy improves overall sustainability by lowering costs and carbon emissions in algal biorefineries, eventually contributing towards the much touted circular, net-zero carbon future economies. Finally, this review analyses the evolution of citation networks, which in turn highlight the emergence of a new frontier of sustainable polymers from algae.

Comparison of the anticancer effect of microalgal oils and microalgal oil-loaded electrosprayed nanoparticles against PC-3, SHSY-5Y and AGS cell lines

Many of the bioactive substances used in pharmaceutical industry are easily affected by temperature, light and oxygen, and are easily degraded during storage and processing, and exhibit poor adsorption properties during digestion, which limits their direct use. Microalgae are rich in oils which have antimicrobial properties and antioxidants that attract attention in both food and pharmaceutical sectors in recent years. Studies to encapsulate bioactive compound-rich microalgae oils with nanotechnological approaches to improve the physical and chemical stability are relatively new, and it is promising to apply these approaches for pharmaceutical purposes. In this study, cytotoxic effects of oil extracts of Botryococcus braunii and Microcystis aeruginosa and their oil-loaded nanoparticles on L929 cell line, PC-3 prostate cell line, SHSY-5Y neuroblastoma cell line and AGS gastric adenocarcinoma cell line were investigated. The obtained extracts were found to have no cytotoxic effect on L929 cells. However, they showed cytotoxic effect on cancer cells. As for the nanoparticles; a gradual release was determined and the stability of the nanoparticle structure was shown. In the light of obtained findings, it was considered that nanoparticles produced with oil extracts of microalgae which have bioactive substances, have potential to be evaluated especially in pharmaceutical and cosmetic fields.

Cellulose aerogel composites as oil sorbents and their regeneration

Background

With every oil tanker comes the risk of an accident and oil spill. Sorbents are the most suitable means to remove oil spills. Aerogels as sorbents have high porosity and can be made from cellulose from paper waste. The literature does not distinguish between paper and cardboard as sources of cellulose aerogels and little is known about composites of cellulose aerogels consisting of cellulose fibres and chemically untreated, unprocessed fibres or particles of straw, wool, macroalgae or cellulose acetate from cigarette butts. In this study, the sorption properties for marine diesel oil and biodiesel of such aerogels and their regenerative capacity with bioethanol were investigated.

Methods

Cellulose aerogels were prepared from office paper and cardboard waste without and with chemically untreated algae, straw, wool and cellulose acetate as a composite by freeze drying. All samples were hydrophobised with methylsilane. The density to calculate the porosity and the contact angle were determined. Then the sorption capacity was determined over five cycles of sorption of oil and regeneration with bioethanol.

Results

The average contact angle of all samples was 125°, indicating hydrophobicity. Paper-based aerogels were found to consistently have higher sorption capacities for biodiesel, marine diesel oil and bioethanol than cardboard-based aerogels. In particular, the wool/cellulose aerogel composite was found to have better sorption capacity for biodiesel, marine diesel oil and bioethanol than all other samples. The cellulose acetate/cellulose aerogel composite showed significantly higher sorption capacities than the paper and cardboard control samples (highest value is 32.25 g g⁻¹) only when first used as a sorbent for biodiesel, but with a rapid decrease in the following cycles.

A sustainable solution to plastics pollution: An eco-friendly bioplastic film production from high-salt contained Spirulina sp. residues

Plastic products have become a major contaminant in environmental ecology due to their recalcitrant biodegradation, poor management and risky disposal. Therefore, much research attention has been paid to developing the biodegradable bio-based plastics. However, many of the substitute bioplastics derived from agricultural materials may present a potential threat to food security and eco-systems. Herein, we propose a sustainable, eco-friendly and simple procedure to convert the hazardous high-salt contained microalgal residues into bioplastic film. With 35 % poly (vinyl alcohol) (PVA) assistance, the composite bioplastic films achieved 22 MPa tensile strength under alkali condition and 77 % elongation at break under acidic condition. The average maximum contact angle of 94.4° confirmed a desirable water resistance potential. The synthesis mechanism demonstrated that the inorganic salts existed in microalgal residues could act as the filler in shape of sheets under alkali condition or as the cross linker under acidic condition, significantly enhancing the practical feasibility. This work demonstrates a promising biodegradable bioplastics formed from sustainable eco-friendly waste reutilization process, providing a new insight for fundamentally reducing the plastics pollution.

Chlamydomonas angulosa (Green Alga) and Nostoc commune (Blue-Green Alga) Microalgae-Cellulose Composite Aerogel Beads: Manufacture, Physicochemical Characterization, and Cd (II) Adsorption

This study presents composite aerogel beads prepared by mixing dissolved cellulose with Chlamydomonas angulosa and Nostoc commune cells, respectively, at 0.1, 0.3, and 0.5% (w/w). The manufactured composites (termed regenerated cellulose (RC)), with C. angulosa (RCCA-(1, 3, and 5)), and with N. commune (RCNC-(1, 3, and 5)) were analyzed. Both RCCA-5 and RCNC-5 showed the high specific surface area to be about 261.3 and 332.8 m²·g⁻¹. In the microstructure analysis, network structures were observed in the cross-sections of RC, RCCA-5, and RCNC-5. The pyrolysis temperature of the RCCA-5 and RCNC-5 composite aerogel beads was rapidly increased about 250 °C during the mixing of cellulose with C. angulosa and N. commune. The chemical analysis of RC, RCCA-5, and RCNC-5 showed peaks corresponding to various functional groups, such as amide, carboxyl, and hydroxyl groups from protein, lipid, and carbohydrate. RCNC-5 at pH 6 demonstrated highest Cd²⁺ removal rate about 90.3%, 82.1%, and 63.1% at 10, 25, and 50 ppm Cd²⁺, respectively. At pH 6, Cd²⁺ adsorption rates per unit weight of the RCNC-5 were about 0.9025, 2.0514, and 3.1547 mg/g at 10, 25, and 50 ppm, respectively. The peaks assigned to the amide, carboxyl, and hydroxyl groups in RCCA-5, RCNC-5, and RC were shifted or disappeared immediately after adsorption of Cd²⁺. The specific surface area, total pore volume, and mean pore diameter of composites was decreased due to adsorption of Cd²⁺ on the developed materials. As can be seen in the X-ray powder diffraction (XRD) spectrum, significant changes in the molecular structure of the composite aerogel beads were not observed even after adsorption of Cd²⁺.

Structure-property relationships of Thai silk-microcrystalline cellulose biocomposite materials fabricated from ionic liquid

Biomaterials made from natural proteins and polysaccharides have become increasingly popular in the biomedical field due to their good biocompatibility and tunable biodegradability. However, the low miscibility of polysaccharides with proteins presents challenges in the creation of protein-polysaccharide composite materials. In this study, neat 1-allyl-3-methylimidazolium chloride (AMIMCl) ionic liquid was used to regenerate Thailand gold Bombyx mori silk and microcrystalline cellulose blended films. This solvent was found to not only effectively dissolve both natural polymers, but also preserve the structure and integrity of the polymers. A single glass transition temperature for each blend was found in DSC curves, indicating good miscibility between the Thai silk and cellulose molecules. The structural composition as well as the morphology and thermal stability of blend films were then determined using FTIR, SEM and TGA. It was found that by varying the ratio of Thai silk to cellulose, the thermal and physical properties of the material could be tuned. Blended films tended to be more thermally stable which could be due to the presence of hydrophobic-hydrophobic or electrostatic interactions between the silk and cellulose. These studies offered a new pathway to understand the tunable properties of protein-polysaccharide composite biomaterials with controllable physical and biological properties.