Dose evaluation and measurement of the 188Re liquid-filled balloon in intravascular brachytherapy

Dosimetry study for beta-radiation treatment of in-stent restenosis

Intravascular brachytherapy (IVBT) has been recognised as a treatment modality for reducing coronary restenosis after angioplasty and stent-implantation procedures. For the treatment of in-stent restenosis using beta-emitter (188)Re, delivering adequate doses to the entire vessel wall is not possible without the potential of overdosing tissues. A method to measure the dose distribution, perturbation and percentage depth dose using plane-parallel and cylindrical tissue-equivalent phantoms has been developed. Good agreement was found between experimental results and Monte Carlo simulation performed using MCNP4C code. The dose given to the affected area in the vascular region for intravascular radiation treatment was 15-30 Gy. Dose inhomogeneity beyond the stent surface decreased significantly with increasing radial distance. In the region close to the stent outer surface (>0.5-mm radial distance), a dose reduction of 11-17% due to the stent was observed. However, the dose perturbations due to the physical properties of metallic stents were found to be significant in IVBT for in-stent restenosis by using measured dose profiles in phantoms. The method can provide accuracy in beta isotope in vivo dosimetry results for treatments involving short-range dose distributions and provide a relatively high-level spatial resolution for detection.

Monte Carlo dose calculations using MCNP4C and EGSnrc/BEAMnrc codes to study the energy dependence of the radiochromic film response to beta-emitting sources

The energy dependence of the radiochromic film (RCF) response to beta-emitting sources was studied by dose theoretical calculations, employing the MCNP4C and EGSnrc/BEAMnrc Monte Carlo codes. Irradiations with virtual monochromatic electron sources, electron and photon clinical beams, a (32)P intravascular brachytherapy (IVB) source and other beta-emitting radioisotopes ((188)Re, (90)Y, (90)Sr/(90)Y,(32)P) were simulated. The MD-55-2 and HS radiochromic films (RCFs) were considered, in a planar or cylindrical irradiation geometry, with water or polystyrene as the surrounding medium. For virtual monochromatic sources, a monotonic decrease with energy of the dose absorbed to the film, with respect to that absorbed to the surrounding medium, was evidenced. Considering the IVB (32)P source and the MD-55-2 in a cylindrical geometry, the calibration with a 6 MeV electron beam would yield dose underestimations from 14 to 23%, increasing the source-to-film radial distance from 1 to 6 mm. For the planar beta-emitting sources in water, calibrations with photon or electron clinical beams would yield dose underestimations between 5 and 12%. Calibrating the RCF with (90)Sr/(90)Y, the MD-55-2 would yield dose underestimations between 3 and 5% for (32)P and discrepancies within +/-2% for (188)Re and (90)Y, whereas for the HS the dose underestimation would reach 4% with (188)Re and 6% with (32)P.

Absolute counting of 188Re radiopharmaceuticals

The Institute of Nuclear Energy Research (INER) has provided 188Re radiopharmaceuticals for hospitals in Taiwan. To enhance the accuracy of commercial radionuclide calibrators used by radiopharmacies and hospitals, and to ensure that patients receive proper doses of these radiopharmaceuticals, it is very important to standardize this nuclide. The 4pibeta-gamma coincidence counting method was used to standardize the mass activities of 188Re in this study. At the same time, three well type ionization chambers, Centronic IG11-N20, Centronic IG11-A20, and ISOCAL-IV, were calibrated by the standardized solutions of the nuclide. In this research, the calibration figures of ISOCAL-IV for the nuclide were consistent with the results of National Physical Laboratory (NPL, UK). The outcome implied that the results of coincidence counting did mutually agree. On the other hand, the radionuclide calibrator in the radiopharmacy was producing measurement errors of about 20% when using the manufacturers recommended calibration setting: an accurate correction factor has now been determined in this study.