A theoretical approach to calibrate radiation portal monitor (RPM) systems

A novel analytical method to calibrate cylindrical side-hole type sodium iodide scintillation detectors

Geometrical and absolute efficiencies play a significant role in the calibration of radioactivity measuring systems, which are regularly complicated. A novel analytical method of efficiency calibration is proposed for cylindrical side-hole type sodium iodide scintillation detectors. Cylindrical side-hole type sodium iodide scintillation detectors have a cylindrical side-hole passing perpendicularly on the sodium iodide crystal axis, which is gathered in the aluminum cover. This detector is a setup for low-level gamma radiation measurement, because of the close 4π solid angle correlated with it, this setup is convenient when low-energy radiation requires efficient detection. Also, the 4π gamma-ray counting is an established way for direct activity measurements and is remarkably well suited for radionuclides with complex gamma-ray spectra. This novel approach depends on the calculation of two primary factors, the photon path length inside the detector active material, and the solid angle, delimited by the radiation source-detector system. In addition, the attenuation of photons by the sodium iodide crystal covering substance is also included by determining the photon path length through this substance. The novel analytical approach calculates the total and geometrical efficiencies of this kind of detector. In comparison, the differences with the published data in the literature indicate that the current approach is favorable in the efficiency measurement of the cylindrical side-hole type sodium iodide scintillation detectors.

Gamma-Ray Attenuation and Exposure Buildup Factor of Novel Polymers in Shielding Using Geant4 Simulation

Polymers are often used in medical applications, therefore, some novel polymers and their interactions with photons have been studied. The gamma-ray shielding parameters for Polymethylpentene (PMP), Polybutylene terephthalate (PBT), Polyoxymethylene (POM), Polyvinylidenefluoride (PVDF), and Polychlorotrifluoroethylene (PCTFE) polymers were determined using the Geant4 simulation and discussed in the current work. The mass attenuation coefficients (μ/ρ) were simulated at low and high energies between 0.059 and 1.408 MeV using different radionuclides. The accuracy of the Geant4 simulated results were checked with the XCOM software. The two different methods had good agreement with each other. Exposure buildup factor (EBF) was calculated and discussed in terms of polymers under study and photon energy. Effective atomic number (Z_eff) and electron density (N_eff) were calculated and analyzed at different energies. Additionally, the half-value layer (HVL) of the polymers was evaluated, and the results of this parameter showed that PCTFE had the highest probability of interaction with gamma photons compared to those of the other tested polymers.

Photopeak Efficiency and Coincidence Summing Factors for HPGe Detectors Using Bulk Sources

In the field of gamma-ray spectroscopy with high-purity germanium detectors, used to measure the activity when the sample to be measured has low radioactivity, volumetric sources are widely used. To determine the sample activity, the full-energy peak efficiency is needed. Bulk sources are very common for low-level radioactivity measurements in activation analysis and environmental samples. The main problem with these measurements is that coincidence effects are large for close source-detector geometries. Ignoring these effects can lead to an error typically of a factor of 2 in the determination of Co and Y activity, which was used in this work in the calibration process. Extensive experimental readings have been carried out, and bulk gamma aqueous sources containing several radionuclides covering the energy range from 60 to 1,840 keV were used. By comparison, the experimental (present work) and theoretical (published) full-energy peak efficiency values are in good agreement; the overall percentage error is less than 6%.

Calibration of the Absolute Efficiency of Well-Type NaI(Tl) Scintillation Detector in 0.121–1.408 MeV Energy Range

Well-type NaI(Tl) detectors are beneficial for low-level photon activity measurements because of the near 4π solid angle that can be gained with them. The detection efficiency can differ with the source-to-detector system geometries, the absorption of the photon in the detector material, and attenuation layers in front of the detector face. For these purposes, the absolute efficiency and the coincidence corrections of the well-type sodium iodide detector have been measured at 0.121–1.408 MeV energy range (obtained from 152Eu, 137Cs, and 60Co radioactive isotopes). The covenant between the experimental (present work) and the published theoretical values is good, with the high discrepancies being less than 1%.

Geometrical and total efficiencies of CdZnTe rectangular parallelepiped detector using arbitrary positioned point, plane, and volumetric sources

Gamma-ray detectors are widely used in many fields like environmental measurements, medicine, space science, and industry, where the detector geometrical, total, photopeak efficiencies and peak-to-total ratio could be required. The calculation of the detector efficiency depends mainly on the value of the geometrical efficiency, which depends on the solid angle subtended by the source-detector system. The present work introduces a direct analytical method to calculate the geometrical and total efficiencies of CdZnTe gamma-ray detector using off-axis isotropic radiating γ-ray [point, disk, and cylindrical] sources. To test the validity of the present work, the results are compared with some published data and also to prove how much it is important to determine the efficiency of difficult gamma-ray detection arrangement.