Determination of plastic constitutive properties of microparticles through single particle compression

Characterization of mechanical behaviour of aluminum powders under fast dynamic conditions

Cold spray is a process belonging to the thermal spray family, characterized by relatively low temperatures and high particle velocities. Upon impact, particles undergo large plastic deformation at solid state in dynamic regime up to 109 s-1. The knowledge of powder behaviour in such conditions is essential to catch key phenomena in cold spray and a necessary step for a correct process modelling. However, little is known on mechanical behaviour of feed-stock powders when submitted to cold spray conditions. In this study, an approach focused on single particles combining laser shock induced impact, namely LASHPOL (LAser SHock POwder Launcher), and quasi-static compression was therefore developed. This method was applied in this study on spherical Aluminium powders but can work with any other powder material. The mechanical behaviour of powders was characterized and used to fit the parameters of Johnson-Cook constitutive model, by means of finite element inverse method. The combination of static and dynamic tests resulted in an original characterization of powder, which revealed having a different mechanical behaviour than the corresponding bulk material.

Rapidly Solidified Gas-Atomized Aluminum Alloys Compared with Conventionally Cast Counterparts: Implications for Cold Spray Materials Consolidation

In this work, three commercially available aluminum alloy systems (Al 2024, Al 6061, and Al 7075) were considered to explicitly capture the differences in material properties associated with a rapidly solidified, gas-atomized particulate feedstock as compared with their conventionally cast counterparts. Differences between the microstructural, thermodynamic, mechanical, and kinetic behaviors associated with gas-atomized and conventionally bulk counterparts have been tacitly assumed by the cold spray community. However, many researchers continue to utilize legacy properties from bulk materials when simulating particle impact phenomena in silico, for example. By way of recognizing the fact that bulk material properties may not serve as substitutes for gas-atomized powder property input parameters for cold spray process simulation and computation in silico, enhanced cold spray research and development will be more easily achieved. Therefore, understanding the feedstock powder characteristics for use in cold spray can lead to fine-tuning the properties of cold spray consolidations. Optical microscopy, scanning electron microscopy, nanoindentation, microhardness, differential scanning calorimetry, elemental analysis, and cooling rate calculations were utilized. This work confirms preliminary findings that powder alloys may not be treated the same way as their bulk counterparts in so far as the enactment of heat treatment processing parameters are concerned. Specifically, vast discrepancies were found in the grain size, secondary phases, and mechanical behavior between the powder and cast versions of each alloy.

Nanomechanical Characterization for Cold Spray: From Feedstock to Consolidated Material Properties

Cold gas-dynamic spray is a solid-state materials consolidation technology that has experienced successful adoption within the coatings, remanufacturing and repair sectors of the advanced manufacturing community. As of late, cold spray has also emerged as a high deposition rate metal additive manufacturing method for structural and nonstructural applications. As cold spray enjoys wider recognition and adoption, the demand for versatile, high-throughput and significant methods of particulate feedstock as well consolidated materials characterization has also become more notable. In order to address the interest for such an instrument, nanoindentation is presented herein as a viable means of achieving the desired mechanical characterization abilities. In this work, conventionally static nanoindentation testing using both Berkovich and spherical indenter tips, as well as nanoindentation using the continuous stiffness measurement mode of testing, will be applied to a range of powder-based feedstocks and cold sprayed materials.

Particle Compression Test: A Key Step towards Tailoring of Feedstock Powder for Cold Spraying

Cold spray is on the way to becoming a mainstream technology for coating and additive manufacturing processes. While there have been many advances in various aspects of this technology, the question of tailoring the ‘ideal’ feedstock powder for cold spraying has remained open. In particular, the mechanical strength and its dependence on the particle size, which are amongst the most relevant properties of the feedstock powder for cold spraying, are rarely covered when reporting powder specifications. This is mainly because of the lack of standardised methods of characterisation for these specific properties. In the present case study, we demonstrate how compression tests of single Inconel 718 particles by using a modified nanoindenter can address this central question. Data analyses are supported by finite element modelling of particle compression for a range of plastic behaviours. The results of simulation are then stored in the form of a surrogate model for subsequent comparison with the experimental data. Thus, the ultimate tensile strength and the size of the examined particles are calculated directly from the measured force-displacement data. The paper will also discuss how this information can be used to optimise cold spraying, and so, unveils a key step towards the design and manufacturing of cold-spray-specific feedstock powder.