Adsorption of bentazon on activated carbon prepared from Lawsonia inermis wood: Equilibrium, kinetic and thermodynamic studies

Low-cost materials as vehicles for pesticides in aquatic media: a review of the current status of different biosorbents employed, optimization by RSM approach

Water contamination by pesticides is increasing dramatically due to population growth and the extensive use of pesticides in agriculture, leading to grave environmental and health concerns. Thus, efficient processes and the design and development of effective treatment technologies are required due to the enormous demand for fresh water. The adsorption approach has been widely used to remove organic contaminants such as pesticides because of its performance, less expense, high selectivity, and simplicity of operation compared to other treatment technologies. Among alternative adsorbents, biomaterials abundantly available for pesticide sorption from water resources have attracted the attention of researchers worldwide. The main objective of this review article is to (i) present studies on a wide range of raw or chemically modified biomaterials potentially effective in removing pesticides from aqueous media; (ii) indicating the effectiveness of biosorbents as green and low-cost materials for removing pesticides from wastewater; and (iii) furthermore, report the application of response surface methodology (RSM) for modeling and optimizing adsorption.

Paracetamol and Ibuprofen Removal from Aqueous Phase Using a Ceramic-Derived Activated Carbon

Emerging pollutants, including pharmaceuticals and personal care products, have been detected in surface and groundwaters. The adsorption of paracetamol and ibuprofen, two widespread drugs, has been studied in aqueous medium, using a ceramic-derived carbon (CeDC) and a commercial activated carbon (CoAC). CeDC yielded a BET surface area of 895 m² g^-1, a bimodal pore size distribution (13.2 and 35 nm) and a total pore volume of 1.99 cm³ g^-1. CoAC had an approximate surface area of 1000 m² g^-1, a homogeneous pore size distribution and a total pore volume of 0.42 cm³ g^-1. Kinetic and equilibrium tests were carried out in batch systems to study the materials' sorption performances. The intraparticle diffusion model best fitted the experimental kinetic data. The maximum ibuprofen sorption capacities were 120 mg g^-1 and 133 mg g^-1 for CoAC and CeDC, respectively, whereas no major differences on the maximum paracetamol sorption capacities (qm) were observed among the sorbents (150-159 mg g^-1). Therefore, CeDC, synthesized easily from a ceramic composite, improved time and sorption capacity of paracetamol and ibuprofen compared to the commercial activated carbon, indicating the potential of the developed carbon as an emerging pollutant sorbent material.

Investigation into Biosorption of Pharmaceuticals from Aqueous Solutions by Biocomposite Material Based on Microbial Biomass and Natural Polymer: Process Variables Optimization and Kinetic Studies

Biosorbtive removal of the antibacterial drug, ethacridine lactate (EL), from aqueous solutions was investigated using as biosorbent Saccharomyces pastorianus residual biomass immobilized in calcium alginate. The aim of this work was to optimize the biosorption process and to evaluate the biosorption capacity in the batch system. Response surface methodology, based on a Box–Behnken design, was used to optimize the EL biosorption parameters. Two response functions (removal efficiency and biosorption capacity) were maximized dependent on three factors: initial concentration of EL solution, contact time, and agitation speed. The highest values for the studied functions (89.49%, 26.04 mg/g) were obtained in the following operational conditions: EL initial concentration: 59.73 mg/L; contact time: 94.26 min; agitation speed: 297.57 rpm. A number of nonlinear kinetic models, including pseudo-first-order, pseudo-second-order, Elovich, and Avrami, were utilized to validate the biosorption kinetic behavior of EL in the optimized conditions. The kinetic data fitted the pseudo-first-order and Avrami models. The experimental results demonstrated that the optimized parameters (especially the agitation speed) significantly affect biosorption and should be considered important in such studies.

Biodegradation of Endosulfan-a Chlorinated Cyclodiene Pesticide by Indigenous Pseudomonas sp. MSCAS BT01

Endosulfan remains as a lipophilic insecticide that causes serious medical problems because of biological stability and toxicity also found in air, water, soil sediments, and foodstuffs. Henceforward, the present study reveals a novel bacterial species isolated from pesticide-contaminated soil for enhanced endosulfan degradation. Next, isolated bacterial species was characterized with biochemical assays and 16S rRNA sequencing technique. Subsequently, the optimal conditions for endosulfan biodegradation such as pH, concentration of endosulfan, and bacterial growth were estimated with non-sulfur medium (NSM). Sequentially, the amount of endosulfan and compound degradation were analyzed through thin-layer chromatography and gas chromatography/mass spectrometry. Overall, the obtained results revealed the endosulfan acting as primary carbon source for bacterial growth. From the GC-MS analysis, the metabolic products released during endosulfan degradation by Pseudomonas sp. MSCAS BT01 were compared with standard GC-MS spectra. The highest (98%) endosulfan degradation was obtained at pH 7.0. The complete endosulfan degradation was achieved at 14th day of incubation and the less toxic endosulfan diol produced was observed via GC-MS. To conclude, the pesticide-contaminated isolate Pseudomonas sp. MSCAS BT01 emerged as a promising bioremediation tool and effectively employed to degrade endosulfan from contaminated soils, sediments, and wastewaters in the days yet to come.

Glyphosate adsorption onto porous clay heterostructure (PCH): kinetic and thermodynamic studies

The synthesis of PCH from natural bentonite produces a porous heterostructure material effective for the adsorption of glyphosate from water. The adsorption process takes place through an interaction between the silanol group of montmorillonite and/or the PCH adsorbent with the functional groups of glyphosate. The glyphosate adsorption isotherms, recorded for all the studied samples, have been established to be of Langmuir type. The kinetic of the herbicide adsorption on the PCH was best described by the pseudo-second-order model. With the increase in temperature from 25 to 50 °C, the sorption capacities of the materials studied towards glyphosate increased. The process of glyphosate adsorption was found to be endothermic and spontaneous in nature, as indicated by positive values of ΔH and negative values of ΔG. According to the results obtained, the herbicide sorption was more effective in a basic environment. The maximum amount of adsorbed glyphosate is almost doubled with PCH from 13.5 mg/g of natural clay to 27.5 mg/g of PCH.

Graphic abstract

Biosorption of oxybenzene using biosorbent prepared by raw wastes of Zea mays and comparative study by using commercially available activated carbon

Organic pollutants present in waste water have undesirable effect on the environment. Industry activities are the key sources of organic pollutants. Prime pollutants released from various sources react instantly with the environment and become derived (secondary) pollutants, which stay for an elongated time. The present research work has been carried out using biosorbent prepared from various Zea mays wastes for elimination of oxybenzene. Different parameters viz contact time, initial concentration; adsorbent dose, temperature and pH were optimized for the biosorption of oxybenzene on to the biosorbent samples. BCS (Baby corn silk) showed higher percentage of biosorption at optimum contact time of 3 h, pH between 5 and 6 and temperature at 25 °C. Analysis of equilibrium biosorption data in terms of several isotherm models revealed that Langmuir isotherm and Freundlich isotherm indicates better agreement with the experimental data. The kinetics of oxybenzene biosorption on to the biosorbents was described with the pseudo-first-order model. Thermodynamic parameters indicated that biosorption onto biosorbent was feasible in nature, spontaneous, and endothermic for some biosorbents, but on contrary not feasible, exothermic and non spontaneous for other biosorbents. The result of this study showed that the biosorbent derived from Zea mays can be used as a prospective biosorbent for oxybenzene in wastewater and also can be an alternative for the commercially activated carbon.

Removal of Fluorescein Dye from Aqueous Solutions Using Natural and Chemically Treated Pine Sawdust

The various factors affecting the removal of fluorescein dye using sawdust from aqueous solutions such as time, initial concentration, pH, and temperature were studied. The optimal conditions for removing the FD are 1 g of sawdust at pH 3 and 120 min time of contact. Dye removal dropped from 93.42% to 80.04% with natural pine sawdust (NPS) and from 96.83% to 81.51% with synthetic pine sawdust (SPS) by increasing their concentration from 2 to 10 mg/L. Isotherm, kinetic, and thermodynamic models were applied for determining their constants. The results indicated that the FD removal equilibrium was effectively defined by the Langmuir, Freundlich, and Temkin models. Kinetic studies showed that the pseudo-second order was well suited for dye removal, and the internal diffusion process was by two steps. The thermodynamic parameter values suggested that FD removal were physical adsorption, exothermic, lower randomness, and spontaneous.

Production of activated carbon from Elaeagnus angustifolia seeds using H3PO4 activator and methylene blue and malachite green adsorption

In this study, activated carbon was obtained from Elaeagnus angustifolia seeds and its usability in the adsorption of methylene blue (MB) and malachite green (MG) from aqueous solution was investigated. Activated carbon was synthesized by chemical activation method using H₃PO₄ as an activator. In the synthesis of the activated carbon, the effects of various parameters such as the rate of impregnation, duration of activation, temperature of activation and duration of activation were investigated. The characterization of the synthesized activated carbons was carried out by FTIR, SEM and BET analyses and the surface area of the produced activated carbon was determined to be 1,194 m² g^-1. The effects of solution initial pH, solution initial concentration and amount of activated carbon on MB and MG adsorption were investigated. The adsorption capacity was found to be higher when the pH of the solution was 8 for MB and 4 for MG. The adsorption kinetics of MB and MG were found to fit the Elovich kinetic model and pseudo-first-order kinetic model, respectively. Adsorption equilibrium data were found to be compatible with Langmuir isotherm for both dyes. According to the Langmuir isotherm, q_max adsorption capacity was found to be 72 mg/g and 115 mg/g for MB and MG, respectively. Novelty Activated carbon was obtained from Elaeagnus angustifolia seeds and its usability in the adsorption of methylene blue (MB) and malachite green (MG) from aqueous solution was investigated. A high surface area activated carbon was synthesized. The surface area of the produced activated carbon was determined to be 1,194 m² g^-1. According to the Langmuir isotherm, q_max adsorption capacity was found to be 72 mg/g and 115 mg/g for MB and MG, respectively. It has been determined that the adsorption capacity of synthesized activated carbon is high.

Pesticides in aquatic environments and their removal by adsorption methods

Although pesticides are widely used in agriculture, industry and households, they pose a risk to human health and ecosystems. Based on target organisms, the main types of pesticides are herbicides, insecticides and fungicides, of which herbicides accounted for 46% of the total pesticide usage worldwide. The movement of pesticides into water bodies occurs through run-off, spray drift, leaching, and sub-surface drainage, all of which have negative impacts on aquatic environments and humans. We sought to define the critical factors affecting the fluxes of contaminants into receiving waters. We also aimed to specify the feasibility of using sorbents to remove pesticides from waterways. In Karun River in Iran (1.21 × 10⁵ ng/L), pesticide concentrations are above regulatory limits. The concentration of pesticides in fish can reach 26.1 × 10³ μg/kg, specifically methoxychlor herbicide in Perca fluviatilis in Lithuania. During the last years, research has focused on elimination of organic pollutants, such as pesticides, from aqueous solution. Pesticide adsorption onto low-cost materials can effectively remediate contaminated waters. In particular, nanoparticle adsorbents and carbon-based adsorbents exhibit high performance (nearly 100%) in removing pesticides from water bodies.

Porous Activated Carbon from Lignocellulosic Agricultural Waste for the Removal of Acetampirid Pesticide from Aqueous Solutions

A facile eco-friendly approach for acetampirid pesticide removal is presented. The method is based on the use of micro- and mesoporous activated carbon (TPAC) as a natural adsorbent. TPAC was synthesized via chemical treatment of tangerine peels with phosphoric acid. The prepared activated carbon was characterized before and after the adsorption process using Fourier- transform infrared (FTIR), X-ray diffraction (XRD), particle size and surface area. The effects of various parameters on the adsorption of acetampirid including adsorbent dose (0.02–0.2 g), pH 2–8, initial adsorbate concentration (10–100 mg/L), contact time (10–300 min) and temperature (25–50 °C) were studied. Batch adsorption features were evaluated using Langmuir and Freundlich isotherms. The adsorption process followed the Langmuir isotherm model with a maximum adsorption capacity of 35.7 mg/g and an equilibration time within 240 min. The adsorption kinetics of acetamiprid was fitted to the pseudo-second-order kinetics model. From the thermodynamics perspective, the adsorption was found to be exothermic and spontaneous in nature. TPAC was successfully regenerated and reused for three consecutive cycles. The results of the presented study show that TPAC may be used as an effective eco-friendly, low cost and highly efficient adsorbent for the removal of acetamiprid pesticides from aqueous solutions.

Amyloid Fibrils Aerogel for Sustainable Removal of Organic Contaminants from Water

Water contamination by organic pollutants is ubiquitous and hence a global concern due to detrimental effects on the environment and human health. Here, it is demonstrated that amyloid fibrils aerogels are ideal adsorbers for removing organic pollutants from water. To this end, amyloid fibrils prepared from β-lactoglobulin, the major constituent of milk whey protein, are used as building blocks for the fabrication of the aerogels. The adsorption of Bentazone, Bisphenol A, and Ibuprofen, as model pollutants, is evaluated under quasi-static conditions, without use of energy or pressure. Through adsorption by amyloid fibrils aerogel, excellent removal efficiencies of 92%, 78%, and 98% are demonstrated for Bentazone, Bisphenol A, and Ibuprofen, respectively. Furthermore, the maximum adsorption capacity of amyloid fibrils aerogel for Bentazone, Bisphenol A, and Ibuprofen is 54.2, 50.6, and 69.6 mg g^-1 , respectively. To shed light on the adsorption equilibrium process, adsorption isotherms, binding constants, saturation limits, and the effect of pH are evaluated. Finally, the regeneration of the aerogel over three consecutive cycles is studied, exhibiting high reusability with no significant changes in its removal performance. These results point at amyloid fibrils aerogels as a sustainable, efficient, and inexpensive technology for alleviating the ubiquitous water contamination by organic pollutants.

Adsorptive behaviour of palm oil mill sludge biochar pyrolyzed at low temperature for copper and cadmium removal

In this work, the influence of pyrolysis temperature on the physicochemical properties of palm oil mill sludge biochar (POSB) and its adsorption properties towards cadmium (Cd) and copper (Cu) was investigated. Characterization experiments suggested that POSBs' surface functional groups play the major role in the adsorption process. POSB pyrolyzed at 400 °C showed the best characteristics for Cu and Cd removal. Adsorption study indicated that contact time and shaking speed enhances the adsorption capacity of POSB. It was affirmed that pH adjustment is not necessary for POSB to adsorb Cu and Cd. Mechanism studies fitted well with Langmuir and Pseudo-Second Order model. Thermodynamic parameters indicated that the adsorption was spontaneous, endothermic and correspond to chemical adsorption. The highest uptakes of Cu and Cd were recorded at 48.8 mg/g and 46.2 mg/g respectively. This work verifies that the temperature used for palm oil mill sludge (POS) pyrolysis and adsorption condition played the most prominent role in Cu and Cd removal from aqueous solutions.

Removal of emerging contaminants from the environment by adsorption

Emerging contaminants (EC's) are pollutants of growing concern. They are mainly organic compounds such as: pesticides, pharmaceuticals and personal care products, hormones, plasticizers, food additives, wood preservatives, laundry detergents, surfactants, disinfectants, flame retardants, and other organic compounds that were found recently in natural wastewater stream generated by human and industrial activities. A majority of ECs does not have standard regulations and could lead to lethal effects on human and aquatic life even at small concentrations. The conventional primary and secondary water treatment plants do not remove or degrade these toxic pollutants efficiently and hence need cost effective tertiary treatment method. Adsorption is a promising method worldwide for EC removal since it is low initial cost for implementation, highly-efficient and has simple operating design. Research has shown that the application of different adsorbents such as, activated carbons(ACs), modified biochars (BCs), nanoadsorbents (carbon nanotubes and graphene), composite adsorbents, and other are being used for EC's removal from water and wastewater. The current review intends to investigate adsorption process as an efficient method for the treatment of ECs. The mechanism of adsorption has also been discussed.