Patients prefer a bicruciate-retaining or the medial pivot total knee prosthesis

Tibial post loading increases the risk of aseptic loosening of posterior-stabilized tibial prosthesis

Aseptic loosening is the primary cause of failure following posterior-stabilized total knee arthroplasty. It is unclear whether tibial post loading of posterior-stabilized prosthesis increases the risk of aseptic loosening of the tibial prosthesis. The purpose of this study is to investigate the biomechanical effects of tibial post loading on the tibial prosthesis fixation interface during level walking, squatting, stair descent, and standing up-sitting down activities. In this paper, finite element models with and without post were established to compare the effects of tibial post loading on the von Mises stress of the proximal tibia, shear stress of the cement, and the bone-prosthesis interface micromotion during four physiological activities. The tibial post loading had an insignificant influence on tibial biomechanics and bone-prosthesis interface micromotion during leveling walking activity. However, compared to the insert without post condition, tibial post loading significantly increased the maximum tibial von Mises stress, the maximum shear stress in the medial of cement, and the bone-prosthesis interface peak micromotion by 912.84%, 612.77%, and 921.09%, respectively, at the moment of the maximum flexion angle for the stair descent activity, and 637.92%, 351.43%, and 519.13%, respectively, at the moment of the maximum flexion angle for the standing up-sitting down activity. Tibial post loading increased the risk of postoperative aseptic loosening of tibial prosthesis in patients with posterior-stabilized total knee arthroplasty, and it was recommended that the post-cam contact mechanism of posterior-stabilized prosthesis should be optimized to reduce the biomechanical impact of tibial post loading on tibial prosthesis fixation.

Achieving Specified Laxity in a Noncruciate Total Knee: A Laboratory Design Study

BACKGROUND

Noncruciate total knee arthroplasty designs, including ultracongruent, medially congruent, and medial pivot, are gaining increasing attention in total knee arthroplasty surgery. However, there is no consensus for the bearing surface design, whether there should be different medial, lateral, anterior, and posterior laxities, or whether the medial side should be a medial pivot. This study proposes the criterion of reproducing the laxity of the anatomic knee, defined as the displacements and rotations of the femur on the tibia in the loaded knee when shear and torque are applied. The purpose of this study was to determine the ideal tibial radii to achieve that goal.

METHODS

The femoral component was based on the average knee from 100 mild arthritic knee scans. There were 8 tibial components that were designed with different sagittal radii: antero-medial, antero-lateral, postero-medial, and postero-lateral. Radii were defined as the percent height reduction from full conformity with the femoral profile. Components were 3-dimensional-printed. A test rig was constructed where the tibial component was fixed and shear and torque were applied to the femoral component. Displacements and rotations of the femoral component were measured at 0 and 45° of flexion, the latter representing any flexion angle due to the constant femoral sagittal radius.

RESULTS

Displacements ranged from 0 to 11 mm, and rotations ranged from 1 to 11°. Anterior femoral displacements were higher than posterior due to the shallow distal-anterior femoral profile. The final femoral and tibial components with the most closely matched anatomic laxity values were designed and tested.

CONCLUSIONS

A steeper distal-anterior femoral radius was an advantage. High medial-anterior tibial conformity was important. However, on the lateral side, the posterior sagittal tibial radius had to be shallower than ideal to allow femoral rollback in high flexion. This meant that the posterior laxity displacements on the lateral side were higher than anatomic, and there was no guidance for lateral femoral rollback.

Kinematic Performance of Medial Pivot Total Knee Arthroplasty

BACKGROUND

Total knee arthroplasty (TKA) implants have continued to evolve to accommodate new understandings of knee mechanics. The medial-pivot implant is a newer design, which is intended to limit anterior-posterior translation in the medial compartment while allowing lateral compartment translation. However, evidence for a generalized medial-pivot characteristic across all activities is limited. The purpose of the study was to quantify and compare in vivo knee joint kinematics using high-speed stereo radiography during activities of daily living in patients who have undergone a TKA with a cruciate sacrificing medial-pivot implant to age-matched and sex-matched native controls.

METHODS

Fifteen participants (7 patients, 4 women, mean age 70 years and 8 nonsymptomatic controls, 4 women, mean age 64 years) performed 6 functional tasks in high-speed stereo radiography: deep-knee lunge, chair rise, step down, gait, gait with 90° turn, and seated knee extension. Translational differences between groups (surgical versus control) were assessed for the medial and lateral condyle, while pivot location was normalized to subject-specific tibial plateau geometry.

RESULTS

The surgical cohort displayed a more constrained medial condyle that provided greater stability of the medial compartment and did not result in the paradoxical anterior translation at mid-flexion angles during weight-bearing activities, but was associated with less condylar translation than native knees. Additionally, the transverse tibial pivot location occurs most commonly in the middle third of the tibial plateau and secondarily on the medial third.

CONCLUSIONS

Some variability in pivot location occurs between activities and is more in nonsymptomatic, native knee controls.

Predicting anterior cruciate ligament degeneration using magnetic resonance imaging: Insights from histological evaluation

BACKGROUND

Mucoid degeneration of the anterior cruciate ligament is a pathological condition that may impair knee mechanics and contribute to the symptomatology of osteoarthritis. This study aimed to evaluate whether preoperative magnetic resonance imaging can predict anterior cruciate ligament degeneration, specifically mucoid degeneration, and to elucidate the histopathological characteristics of mucoid degeneration in knee osteoarthritis patients.

METHODS

We evaluated a total of 95 knees of osteoarthritis patients (23 males, 72 females; mean age: 72.7 ± 7.5) scheduled for total knee arthroplasty. The relationship between preoperative magnetic resonance imaging findings and the histopathological evidence of anterior cruciate ligament mucoid degeneration was examined. Immunohistochemical analysis was employed for collagen types (COL-I, COL-II), chondrogenesis (SOX9), and vascularity (CD31).

RESULTS

High signal intensity on magnetic resonance imaging showed a positive correlation with Alcian Blue staining areas (rs = 0.59, p < 0.01) and the swelling index (rs = 0.62, p < 0.01), indicating advanced mucoid degeneration. The absence of synovial lining around the anterior cruciate ligament was associated with more severe degeneration. In the histological evaluations, advanced degeneration was characterized by an increase in chondroid metaplasia and collagen disorientation. The Alcian Blue and SOX9 correlation was positive (rs = 0.69, p < 0.01), but negative with COL-I (rs = -0.38, p = 0.03) and vascularity (CD31) (rs = -0.60, p < 0.01).

CONCLUSIONS

Preoperative magnetic resonance imaging is an effective tool in assessing the severity of anterior cruciate ligament degeneration; it influences surgical decisions. High signal intensity on magnetic resonance images denotes advanced mucoid degeneration. The absence of synovial lining around the anterior cruciate ligament is associated with more severe degeneration and may accelerate degenerative changes. Chondroid metaplasia and collagen disorientation mark advanced degeneration. Magnetic resonance imaging can be used to gauge the degree of anterior cruciate ligament degeneration in osteoarthritis.

Bi-cruciate retaining total knee arthroplasty is here to stay: A consecutive series transitioning from manual instrumentation to enabling technologies

BACKGROUND

Bicruciate-retaining (BCR) total knee arthroplasty (TKA) has seen renewed interest due to the potential for more natural knee kinematics with anterior cruciate ligament (ACL) retention.

OBJECTIVE

The present study attempts to determine differences in the 2-year survivorship and patient-reported outcomes between two surgical strategies (traditional instrumentation versus robotics) applied to the extensive use of a modern, 2nd generation BCR TKA design.

METHODS

We performed a retrospective study with prospectively collected data of 113 patients who underwent primary TKA between 2018 and 2020 using a 2nd generation BCR TKA implant. Patient demographics, PROMS, and intra/post-operative complications were collected. Patients were also evaluated according to the use or not of robotics. A Kaplan-Meier analysis was used to evaluate revision-free survival at follow up.

RESULTS

102 patients were enrolled: 90 received traditional surgery and 12 robotic-assisted surgery. The mean age was 68 years (SD 7.76) with an average BMI of 29.6 kg/m2 (SD 3.56). The mean follow up (FU) was 32.4 ± 6.2 months (range 24-45 months). Survivorship at 2 years was 98% (95% CI: 92.4-99.5). Revisions/reoperations were performed for anterior cruciate ligament (ACL) tear (1/4), pain (1/4), arthrofibrosis (1/4) and acute periprosthetic joint infection (PJI) (1/4). At final FU, 92 patients (90.2%) considered themselves satisfied, showing a mean OKS of 40.6 (SD 5.1) and a mean FKS of 76.7 (SD 11.8). No differences in the outcome were found between traditional and robotic-assisted procedures.

CONCLUSION

The modern BCR design evaluated in this study achieved excellent results in terms of implant survivorship, low rate of reoperation and clinical results, independently from the use of enabling technologies.

The wear and kinematics of two medially stabilised total knee replacement systems

BACKGROUND

Medially stabilised total knee replacement systems aim to provide a more natural feeling knee replacement by providing increased stability through flexion. The aim of this study was to compare the kinematics and wear of two different medially stabilised total knee replacement systems in an experimental simulation study. The Medial Rotation Knee™ system (MRK) is an early medially stabilised knee (>20 years clinical success); the SAIPH® knee system being a more modern and refined, bone conserving evolution of the original design with a larger size range.

METHODS

Three SAIPH and three MRK total knee replacements (MatOrtho Ltd, UK) were investigated. The study was performed on a knee simulator with load controlled input kinematic conditions (ISO 14243-1). 6 million cycles of simulation were carried out with the wear of the UHMWPE tibial components assessed gravimetrically. The resulting anterior-posterior translation and tibial rotation position was measured throughout the study.

RESULTS

The mean UHMWPE wear rate was 0.57 ± 0.71 and 1.24 ± 2.0 mm3/million cycles for SAIPH and MRK total knee replacement systems respectively with no significant difference in wear (p = 0.24). Analysis of simulator output kinematics showed a larger range of anterior-posterior motion for SAIPH total knee replacements compared to MRK. The magnitude of tibial rotation was low for both knee replacement systems.

CONCLUSION

The small magnitude of anterior-posterior displacement and tibial rotation motion demonstrates the inherent stability of this knee system design offered by the constrained medial compartment. This study shows the potential for medially stabilised knee systems as a low polyethylene surface wear solution.

Complications of Bicruciate-Retaining Total Knee Arthroplasty: The Importance of Alignment and Balance

Bicruciate-retaining total knee arthroplasty (BCR TKA) results in kinematics closer to the native knee and in greater patient satisfaction but information concerning its outcome and complications is lacking.The goal of this study is to report the clinical and radiological outcomes of BCR prosthesis implanted using a spacer-based gap balancing technique and to assess if some preoperative factors are associated with a worse prognosis.A cohort of 207 knees in 194 patients who underwent BCR TKA, with a minimum 1-year follow-up, was retrospectively analyzed.Patients were followed at 6 weeks, 6 months, 1 year, and then every following year postoperatively, and filled questionnaires (Knee Society and Knee injury and Osteoarthritis Outcome Score) at every visit. Clinical and radiological assessments included range of motion, knee alignment, pain, and complications as defined by the Knee Society's Standardized list and definition of Complication of Total Knee Arthroplasty.Forty-three knees (20.8%) suffered major complications. Twenty-one knees (10.1%) underwent revision at an average of 32.1 months after the index procedure. Revision-free survival at 100 months was 85.7%. Revision was performed for aseptic tibial loosening in eight knees (3.9%) and stiffness in five knees (2.4%). There were 29 reoperations other than revision (14.0%), the most frequent procedure being manipulation under anesthesia in 14 knees (6.8%). Minor complications included tendonitis (20.8%), persistent synovitis (6.8%), and superficial wound infections (6.3%).All outcomes scores were greatly improved at the 1-year follow-up compared with preoperatively (p < 0.001). However, maximum flexion at the last follow-up was significantly reduced compared with preoperatively (mean maximum flexion ± standard deviation: 119.9 ± 15.6 vs. 129.9 ± 14.4, p < 0.001). Aseptic tibial loosening was associated with a hypercorrection in varus of preoperative valgus knees (p = 0.012).BCR TKA can give functional results similar to other types of prostheses but involves a substantial risk of complications. Important factors that can explain failed BCR TKA and guide its use were identified, more particularly knee alignment and its role in aseptic tibial loosening.

Short-term clinical results of bicruciate-retaining total knee arthroplasty using personalized alignment

BACKGROUND

Bicruciate-retaining (BCR) prosthesis has been introduced to recreate normal knee movement by preserving both the anterior and posterior cruciate ligaments. However, the use of BCR total knee arthroplasty (TKA) is still debatable because of several disappointing reports. We have been performing BCR TKAs with personalized alignment (PA). This study aimed to reveal the limb alignment and soft tissue balance of FA-BCR TKAs and compare the clinical outcomes of FA-BCR TKAs with those of unicompartmental knee arthroplasty (UKA).

METHODS

Fifty BCR TKAs and 58 UKAs were included in this study. The joint component gaps of BCR TKA were evaluated intraoperatively and the postoperative hip-knee-ankle (HKA) angle, medial proximal tibial angle (MPTA), and lateral distal femoral angle (LDFA) were measured using full-length standing radiography. The short-term clinical outcomes of BCR TKAs were compared with those of UKA using the scoring system of 2011 Knee Society Scoring (KSS) and the knee injury and osteoarthritis outcome score (KOOS) at an average of 2 years postoperatively (1-4yeras).

RESULTS

The coronal alignment values of PA-BCR TKA were as follows: HKA angle, 177.9° ± 2.3°; MPTA, 85.4° ± 1.9°; and LDFA, 87.5° ± 1.9°. The joint component gaps at flexion angles of 10°, 30°, 60°, and 90° were 11.1 ± 1.2, 10.9 ± 1.4, 10.7 ± 1.3, and 11.2 ± 1.4 mm for the medial compartment and 12.9 ± 1.5, 12.6 ± 1.8, 12.5 ± 1.8 and 12.5 ± 1.7 mm for the lateral compartment, respectively. The patient expectation score and maximum extension angle of PA-BCR TKA were significantly better than those of UKAs.

CONCLUSIONS

The short-term clinical outcomes of PA-BCR TKA were comparable or a slightly superior to those of UKAs.

The Effect of Congruent Tibial Inserts in Total Knee Arthroplasty: A Network Meta-Analysis of Randomized Controlled Trials

Objective: The aim of this study was to determine whether modern congruent tibial inserts are associated with superior outcomes in total knee arthroplasty (TKA). Background: Ultracongruent fixed-bearing (UCFB) and medial congruent fixed-bearing (MCFB) inserts have been known to be effective in total knee arthroplasty with patient satisfaction. Nonetheless, no supporting evidence to date exists to rank the clinical outcomes of these various congruent inserts in TKA compared with other important considerations in TKA including cruciate-retaining fixed-bearing (CRFB) and posterior-stabilized fixed-bearing (PSFB) inserts. Methods: We searched PubMed, Embase, the Cochrane Central Register of Controlled Trials, Web of Science, and Scopus up to 15 May 2022. We selected studies involving an active comparison of UCFB or MCFB in TKAs. We performed a network meta-analysis (NMA) of randomized controlled trials (RCTs) and compared different congruent inserts. We ranked the clinical outcomes by SUCRA score with the estimate of the best treatment probability. Our primary outcomes were revision rates and radiolucent lines. Secondary outcomes were functional scores, including the range of motion (ROM), the Knee Society Score (KSS), the Oxford Knee Score (OKS), and WOMAC. Results: Eighteen RCTs with 1793 participants were analyzed. Our NMA ranked MCFB, CRFB, and UCFB with the lowest revision rates. CRFB and UCFB had the fewest radiolucent lines. UCFB had overall the best ROM. UCFB and MCFB had the best OKS score overall. Conclusions: The ranking probability for better clinical outcomes in congruent inserts demonstrated the superiority of congruent tibial inserts, including UCFB and MCFB. UCFB may be associated with better ROM and postoperative functional outcomes. However, integrating future RCTs for high-level evidence is necessary to confirm these findings.

Medial pivot design does not yield superior results compared to posterior-stabilised total knee arthroplasty: a systematic review and meta-analysis of randomised control trials

PURPOSE

The aim of this meta-analysis was a comparison between medial pivot (MP) and posterior-stabilised (PS) knee designs regarding functional and radiological outcomes as well as gait parameters.

METHODS

A systematic literature search was conducted in PubMed, Cochrane Library, Science Direct and Clinical Trials.gov from conception up to April 2022, to identify eligible randomised control trials (RCTs). The extracted data were analysed according to the Preferred Reporting Items for Systematic reviews and Meta-Analysis (PRISMA) statement.

RESULTS

Fifteen studies met inclusion criteria, enrolling 1101 patients who underwent 1242 total knee arthroplasties (TKAs). A total of 1158 TKAs (581 MP/577 PS) were included in the quantitative analysis. Mean follow-up ranged from 6 months up to 6.6 years. MP knees showed comparable range of motion (ROM) with PS design 1, 2 and 4 years postoperatively (p = 0.2, p = 0.25, p = 0.34, respectively). No statistical difference was found in patient-related outcome measures (PROMs) (p > 0.05). Mean walking speed (MWS), length of stay (LOS), radiographic alignment and complications rates were also similar between the two groups (p > 0.05).

DISCUSSION

The present meta-analysis demonstrated that the theoretical biomechanical advantage of MP implants does not have a better impact on patient satisfaction compared to the traditional PS knees.

LEVEL OF EVIDENCE

I.

Bicruciate-retaining total knee arthroplasty procedure reduced tensile force in the middle and posterior components of lateral collateral ligament during deep knee flexion activities with no effect on tensile force of the medial collateral ligament

PURPOSE

To analyse the effects of bicruciate-retaining total knee arthroplasty (BCR-TKA) on the tensile force of the collateral ligaments during two deep knee flexion activities, cross-leg sitting and squatting.

METHODS

Thirteen patients (15 knees) treated using bicruciate-retaining total knee arthroplasty (BCR-TKA) for knee joint osteoarthritis were analysed. Knee joint kinematics during cross-leg sitting (open-chain flexion) and squatting (closed-chain flexion) were evaluated through fluoroscopy. The tensile force was calculated in vivo based on the change in the distance between the femoral and tibial attachment areas for the anterior, middle, and posterior components of the superficial (sMCL) and deep (dMCL) medial collateral ligament and the lateral collateral ligament (LCL). Differences in the calculated tensile forces of the collateral ligaments were evaluated using repeated measures of analysis of variance, with post hoc pairwise comparison (Bonferroni test). Statistical significance was set at P ≤ 0.05.

RESULTS

The correction of the coronal alignment was related to the surgical technique, not to the implant design. No significant change in the tensile force in all three components of the sMCL from pre- to post-TKA (n.s.) was observed. For dMCL, a pre- to post-TKA change in the tensile force was observed only for the anterior dMCL component (p = 0.03). No change was observed in the tensile force of the anterior LCL with increasing flexion, with no difference in pre- to post-TKA and between activities (n.s.). In contrast, tensile force in the middle LCL slightly decreased with increasing flexion during squatting, pre- and post-TKA. After surgery, lower forces were generated at 40° of flexion (p = 0.04). Tensile force in the posterior LCL was higher in extension than flexion, which remained high in the extension post-TKA. However, after surgery, lower tensile forces were generated at 10° (p = 0.04) and 40° (p = 0.04) of flexion.

CONCLUSIONS

The in vivo change in tensile forces of the collateral ligaments of the knee before and after BCR-TKA can inform the development of appropriate ligament balancing strategies to facilitate recovery of deep knee flexion activities after TKA, as well as for continued improvement of BCR-TKA designs.

LEVEL OF EVIDENCE

III.

Bicruciate retaining total knee arthroplasty: current state and future promise

Total knee arthroplasty (TKA) is a well-known surgical procedure performed to address end stage osteoarthritis. The main goal is to relieve pain, recover articular function and return to normal function as soon as possible. Over the years it is frequently performed in the elderly, but lately there is an increased demand in a younger and more active population. Up to 25% of patients feel dissatisfied about their TKA. The anterior cruciate ligament (ACL) is considered the main anteroposterior stabilizer of the knee; nevertheless the ACL is usually sacrificed during conventional TKA. Research shows this might be an unnecessary sacrifice in certain cases. The considerable dissatisfaction rate in mainly high-demanding patients, together with the literature reports on the importance of the ACL function, were the two main reasons for the development of bicruciate retaining (BCR) total knee arthroplasty. BCR TKA may offer superior knee kinematics and proprioception, through anterior cruciate ligament preservation, but requires a higher level of attention to obtain an accurate and precise component orientation to reach proper ligamentous balancing and restore the native knee biomechanics. Many surgeons abandoned its use due to its challenging technique and inconsistent results. Recent new BCR implant designs are promising. This systematic literature review aims to summarize the current state of BCR TKA and what to expect in the future.

Better flexion and early recovery with medial-stabilized vs single-radius total knee arthroplasty with kinematic alignment: Two-year clinical results

BACKGROUND

There are few studies comparing outcomes in patients with posterior cruciate ligament-sacrificing single-radius (SR) versus medial-stabilized (MS) knee devices. Both types of implants are designed to maximize deep-flexion and to maintain stability throughout the knee flexion arc. The aim of this study was to determine whether two-year outcomes differ between these two implant groups.

METHODS

Two-hundred and ten patients took part in this retrospective cohort single center study. The SR patients (n = 109) were enrolled in one randomized trial, and the MS knees (n = 101) in another. Patient consent and Investigative Review Board approval was obtained. Radiographs and clinical outcomes were gathered preoperatively and at six weeks, six months, one year and two years.

RESULTS

There were no statistically significant differences between treatment groups in terms of preoperative demographic characteristics. The MS group had significantly better knee flexion starting at six months postoperative through two years postoperatively (p < 0.05 - p< 0.001). The Knee Society Pain/Motion score was better in the MS group at one year (95.41 vs 90.86, p < 0.002). The Knee Society Pain score was also better in the MS group starting at six weeks through one year (six weeks: 35.3 vs 30, p = 0.007; one year: 46.4 vs 42.4, p = 0.005, respectively).

CONCLUSION

The MS group had better clinical outcomes than the SR group, with significantly greater knee flexion from six months through two years, better Knee Society Pain scores at six weeks through one year, and higher Knee Society Pain/Motion scores at six weeks and one year postoperatively.

LEVEL OF EVIDENCE

I.

Modern Total Knee Arthroplasty Bearing Designs and the Role of the Posterior Cruciate Ligament

The role of the posterior cruciate ligament (PCL) in total knee arthroplasty (TKA) surgery continues to be a source of debate among the adult reconstruction community. In native knee flexion, the PCL is comprised of an anterolateral and posteromedial bundle that work together to limit posterior tibial translation and allow adequate femoral rollback for deep flexion. In the arthritic knee, the PCL can often become dysfunctional and attenuated, which led to the development of posterior stabilized (PS) TKA bearing options. PS TKAs implement a cam-post construct to functionally replace a resected PCL. While PS designs may facilitate balancing knees with significant deformity, they are associated with complications such as postfracture, increased wear, and patellar clunk/crepitus. In recent years, newer designs have been popularized with greater degrees of congruency and incorporation of medial and lateral pivoting to better recreate native knee kinematics. The American Joint Registry has confirmed the recent predilection for ultra-congruent and cruciate-retaining TKA inserts over PS TKAs during the last decade. Studies have failed to identify an overall clinical superiority between the cruciate substituting and sacrificing designs. The literature has also failed to identify clinical consequences from PCL resection with modern, more conforming TKA designs. In this article, we review modern PCL sacrificing designs and discuss the impact of each on the kinematics after TKA. We also will delineate the role of the PCL in modern TKA in the hopes to better understand the recent surge in sacrificing but not substituting knee implants.

Ball-in-socket medial conformity with posterior cruciate ligament retention neither limits internal tibial rotation and knee flexion nor lowers clinical outcome scores after unrestricted kinematically aligned total knee arthroplasty

PURPOSE

For a new tibial insert design with ball-in-socket (B-in-S) medial conformity (MC), posterior cruciate ligament (PCL) retention, and flat lateral articular surface (B-in-S MC + PCL), this study determined whether internal tibial rotation and knee flexion were limited and clinical outcome scores were lower during weight-bearing activities relative to an insert with intermediate (I) (i.e., less than ball-in-socket) medial conformity (I MC + PCL).

METHODS

Twenty-five patients were treated with bilateral unrestricted, caliper-verified kinematic alignment (KA) total knee arthroplasty (TKA) with an I MC + PCL insert and B-in-S MC + PCL insert in opposite knees. Each patient performed weight-bearing deep knee bend, step up, and chair rise under single-plane fluoroscopy. Analysis following 3D model-to-2D image registration determined internal tibial rotation. For each TKA, knee flexion was measured and patients completed clinical outcome scoring questionnaires.

RESULTS

Internal tibial rotation did not differ between conformities during chair rise and step up (p = 0.3419 and 0.1030, respectively). During deep knee bend, internal tibial rotation between 90° and maximum flexion was 3° greater in the B-in-S MC + PCL group (18° vs 15°) (p = 0.0290). Mean knee flexion (p = 0.3115) and median Forgotten Joint Score (FJS), Oxford Knee Score (OKS), and Western Ontario and McMasters Universities Arthritis Index (WOMAC) scores (p = 0.2100, 0.2154, and 0.4542, respectively) did not differ between conformities.

CONCLUSION

An insert with ball-in-socket medial conformity, which maximizes anteroposterior (AP) stability, did not limit internal tibial rotation and knee flexion and did not lower patient-reported outcomes when implanted with unrestricted caliper-verified KA and PCL retention. The high AP stability provided by the medial ball-in-socket might interest those surgeons exploring the treatment of the active patient with a desire to return to high-level and athletic activities.

Larger Medial Contact Area and More Anterior Contact Position in Medial-Pivot than Posterior-Stabilized Total Knee Arthroplasty during In-Vivo Lunge Activity

This study aimed to compare the in-vivo kinematics and articular contact status between medial-pivot total knee arthroplasty (MP-TKA) and posterior stabilized (PS) TKA during weight-bearing single-leg lunge. 16 MP-TKA and 12 PS-TKA patients performed bilateral single-leg lunges under dual fluoroscopy surveillance to determine the in-vivo six degrees-of-freedom knee kinematics. The closest point between the surface models of the femoral condyle and the polyethylene insert was used to determine the contact position and area. The nonparametric statistics analysis was performed to test the symmetry of the kinematics between MP-TKA and PS-TKA. PS-TKA demonstrated a significantly greater range of AP translation than MP-TKA during high flexion (p = 0.0002). Both groups showed a significantly greater range of lateral compartment posterior translation with medial pivot rotation. The contact points of PS-TKA were located significantly more posterior than MP-TKA in both medial (10°–100°) and lateral (5°–40°, 55°–100°) compartments (p < 0.0500). MP-TKA had a significantly larger contact area in the medial compartment than in the lateral compartment. In contrast, no significant differences were observed in PS-TKA. The present study revealed no significant differences in clinical outcomes between the MP and PS groups. The PS-TKA demonstrated significantly more posterior translations than MP-TKA at high flexion. The contact points are located more posteriorly in PS-TKA compared with MP-TKA. A larger contact area and medial pivot pattern during high flexion in MP-TKA indicated that MP-TKA provides enhanced medial pivot rotation.

Mid-Flexion, Anteroposterior Stability of Total Knee Replacement Implanted with Kinematic Alignment: A Randomized, Quantitative Radiographic Laxity Study with Posterior-Stabilized and Medial-Stabilized Implants

UPDATE

This article was updated on January 4, 2023, because of a previous error, which was discovered after the preliminary version of the article was posted online. On page 16, in Figure 5, the x-axis that had read "P<0.0086" now reads "KSS Pain (p=0.02)," and the value for the MS group that had read "48.9" now reads "48.8."This article was updated on January 6, 2022, because of a previous error. On page 13, in the section entitled "Results," the sentence that had read "However, when only the subset of female subjects was considered, the MS group demonstrated significantly less anteroposterior laxity in 90° of flexion than the MS group (2.3 versus 5.4 mm; p = 0.008)." now reads "However, when only the subset of female subjects was considered, the MS group demonstrated significantly less anteroposterior laxity in 90° of flexion than the PS group (2.3 versus 5.4 mm; p = 0.008)."

BACKGROUND

Stability in mid-flexion is important for satisfactory clinical outcomes following total knee arthroplasty (TKA). The purpose of the present study was to compare the anteroposterior stability of knees that had been treated with a posterior-stabilized (PS) device or a medial-stabilized (MS) device. We hypothesized that mid-flexion laxity would be greater in the PS group and that clinical outcome scores would be better for the group with lower laxity.

METHODS

Sixty-three patients who had been randomly selected from a larger randomized, prospective, blinded clinical trial underwent primary TKA with either a PS implant (n = 30) or an MS implant (n = 33). Range of motion, the Knee Society Score (KSS), and the Forgotten Joint Score (FJS) were collected, and anteroposterior laxity with the knee in 45° and 90° of flexion was evaluated with stress radiographs.

RESULTS

In 45° of flexion, the MS group demonstrated significantly less total anteroposterior displacement than the PS group (mean, 3.6 versus 16.5 mm; p ≤ 0.0001). In 90° of flexion, the total anteroposterior displacement was not significantly different for the 2 groups when both male and female patients were included (mean, 3.9 versus 5.9; p = 0.07). However, when only the subset of female subjects was considered, the MS group demonstrated significantly less anteroposterior laxity in 90° of flexion than the PS group (2.3 versus 5.4 mm; p = 0.008). The groups did not differ significantly in terms of preoperative age, body mass index, sex distribution, FJS, KSS, or range of motion, and they also did not differ in terms of postoperative FJS or range of motion. However, all 33 patients in the MS group returned to sports as indicated in question 12 of the FJS, compared with 19 subjects in the PS group (p = 0.0001). The postoperative KSS Pain, Pain/Motion, and Function scores were all significantly higher in the MS group than the PS; specifically, the mean KSS Pain score was 48.8 in the MS group, compared with 44.8 in the PS group (p = 0.02); the mean KSS Pain/Motion score was 98.4 in the MS group, compared with 89.5 in the PS group (p < 0.0001); and the mean KSS Function score was 95.5 in the MS group, compared with 85.7 in the PS group (p = 0.003).

CONCLUSIONS

Mid-flexion laxity was greater in patients with PS implants than in those with MS implants, and laxity in 90° was greater in the subset of female patients in the PS group. The decreased laxity observed in the MS group correlated with higher KSS Pain, Pain/Motion, and Function scores as well as with a higher rate of return to sports activities.

LEVEL OF EVIDENCE

Therapeutic Level I . See Instructions for Authors for a complete description of levels of evidence.

Early outcomes of a novel bicruciate-retaining knee system: a 2-year minimum retrospective cohort study

INTRODUCTION

Bicruciate retaining (BCR) total knee arthroplasty (TKA) was designed to simulate natural knee kinematics and improve proprioception by retaining both the ACL and PCL. While the prospect of the design appears favorable to patients, previous designs have demonstrated modest survivorship rates compared to traditional designs. This study aims to report the early functional outcomes and implant survivorship of a novel BCR design.

MATERIALS AND METHODS

A multi-center, retrospective study was conducted identifying BCR TKA patients from 2016 to 2017. Patient demographics, quality outcomes, and post-operative complications were collected. A Kaplan-Meier analysis was used to evaluate revision-free survival.

RESULTS

One-hundred thirty-three patients with a mean follow-up time of 2.35 ± 0.25 years (range: 2.00-2.87 years) were identified. Patients receiving BCR TKA were, on average, 61.46 ± 9.27 years-old, obese (BMI = 31.80 ± 6.01 kg/m²), predominantly white (71.4%), and female (69.9%). The device was most often implanted using standard instruments (85.7%) compared to computer-assisted navigation (13.5%). Average length-of-stay was 1.77 ± 0.97 days. Six patients had a reoperation; three (2.5%) full revisions occurred for: infection (n = 1), arthrofibrosis (n = 1), and ACL rupture (n = 1); one (0.8%) tibial revision occurred for: arthrofibrosis; two (1.5%) liner exchanges occurred for: infection (n = 1) and arthrofibrosis (n = 1). Kaplan-Meier survivorship analysis of cumulative failure at 2-year showed a survival rate of 96.2% (95% confidence interval, 91.2-98.4%) for all-cause reoperation, 97.3% (91.6-99.1%) for aseptic revision, and 100% for mechanical failure.

CONCLUSION

Survivorship was 96.2% for all-cause reoperation, 97.3% for aseptic revision, and 100% for mechanical implant failure at 2-years. This novel BCR TKA demonstrated no implant-related complications and excellent survivorship outcomes over 2 years with comparable revision rates to those previously reported in the literature.

Fluoroscopic and radiostereometric analysis of a bicruciate-retaining versus a posterior cruciate-retaining total knee arthroplasty: a randomized controlled trial

AIMS

The aim of this study was to compare a bicruciate-retaining (BCR) total knee arthroplasty (TKA) with a posterior cruciate-retaining (CR) TKA design in terms of kinematics, measured using fluoroscopy and stability as micromotion using radiostereometric analysis (RSA).

METHODS

A total of 40 patients with end-stage osteoarthritis were included in this randomized controlled trial. All patients performed a step-up and lunge task in front of a monoplane fluoroscope one year postoperatively. Femorotibial contact point (CP) locations were determined at every flexion angle and compared between the groups. RSA images were taken at baseline, six weeks, three, six, 12, and 24 months postoperatively. Clinical and functional outcomes were compared postoperatively for two years.

RESULTS

The BCR-TKA demonstrated a kinematic pattern comparable to the natural knee's screw-home mechanism in the step-up task. In the lunge task, the medial CP of the BCR-TKA was more anterior in the early flexion phase, while laterally the CP was more posterior during the entire movement cycle. The BCR-TKA group showed higher tibial migration. No differences were found for the clinical and functional outcomes.

CONCLUSION

The BCR-TKA shows a different kinematic pattern in early flexion/late extension compared to the CR-TKA. The difference between both implants is mostly visible in the flexion phase in which the anterior cruciate ligament is effective; however, both designs fail to fully replicate the motion of a natural knee. The higher migration of the BCR-TKA was concerning and highlights the importance of longer follow-up.Cite this article: Bone Joint J 2023;105-B(1):35-46.

In vivo kinematic comparison of medial pivot total knee arthroplasty in weight-bearing and non-weight-bearing deep knee bending

BACKGROUND

This study aimed to determine the kinematics of medial pivot total knee arthroplasty by comparing weight-bearing and non-weight-bearing deep knee bending and to evaluate the effect of the weight-bearing state on the kinematics.

METHODS

The kinematics of 19 knees were investigated under fluoroscopy during squatting (weight-bearing) and active-assisted knee bending (non-weight-bearing) using two- to three-dimensional registration technique. Accordingly, range of motion, anteroposterior translation for the medial and lateral low contact points, axial rotation of the femoral component relative to the tibial component and kinematic pathway were evaluated.

FINDINGS

There was no difference in range of motion between the two states. The medial anteroposterior translation showed no significant movement with no anterior translation in both the weight-bearing and non-weight-bearing from 0° to 90° of flexion. Regarding the lateral anteroposterior translation, a posterior translation was observed during weight-bearing, whereas a slight anterior translation from 0° to 30° of flexion and subsequent posterior translation were found in the non-weight-bearing. Femoral external rotation was observed in the weight-bearing, whereas femoral internal rotation was seen from 0° to 30° of flexion and subsequent femoral external rotation was observed in the non-weight-bearing. The kinematic pathway showed medial pivot motion and subsequent bicondylar rollback in the weight-bearing, whereas only medial pivot motion was observed in the non-weight-bearing.

INTERPRETATION

The medial anteroposterior translation of the femur during deep knee bending showed no anterior motion in the two states. The lateral anteroposterior translation and femoral rotation were different in the mid-flexion range between the two states.

Does contemporary bicruciate retaining total knee arthroplasty restore the native knee kinematics? A descriptive literature review

BACKGROUND

There has been no consensus on the benefit of retaining the anterior cruciate ligament (ACL) in TKAs. This study aims to review recent evidences around the kinematics of bicruciate retaining (BCR) total knee arthroplasty (TKA).

MATERIALS AND METHODS

A search of the literature was conducted on PubMed and Web of Science. Reports that assessed the BCR TKA kinematics, including both in vitro cadaveric studies and in vivo clinical studies, were reviewed.

RESULTS

A total number of 169 entries were obtained. By exclusion criteria, five in vitro studies using cadaveric knee specimens and six in vivo studies using patient cohorts were retained. In vitro studies showed a low internal rotation (< 10°) throughout the flexion path in all BCR TKAs. Compared to native knees, the difference in the internal rotation was maximal during early and late flexion; the femur in the BCR TKA was significantly more anteriorly positioned (1.7-3.6 mm from 0° to 110°) and more externally rotated (3.6°-4.2° at 110° and 120°). In vivo studies revealed that the native knee kinematics, in general, were not fully restored after BCR TKA during various knee activates (squatting, level-walking, and downhill-walking). There are asymmetric kinematics during the stance phase of gait cycle and a smaller range of axial rotation (23% patients exhibiting external tibial rotation) throughout the gait cycle in BCR TKAs.

CONCLUSIONS

Critical insights in the complex BCR TKA biomechanics have been reported from recent laboratory kinematics studies. However, whether contemporary BCR TKAs can fully restore native knee kinematics remains debatable, warranting further investigations.

Medial Pivot Versus Posterior-Stabilized Prosthesis Design in Primary Total Knee Arthroplasty: A Systematic Review and Meta-Analysis

BACKGROUND

Studies of clinical outcomes that compare the Medial Pivot design (MP) with the Posterior-Stabilized design (PS) were controversial. The meta-analysis was performed to summarize existing evidence, aiming to determine whether MP was superior to PS prosthesis.

METHODS

Search strategies followed the recommendations of the Cochrane collaboration. Electronic searches such as PubMed, Embase, Web of Science, and Cochrane were systematically searched for publications concerning medical pivot and posterior stabilized prosthesis from the inception date to April 2021. Authors also manually checked and retrieved a reference list of included publications for potential studies, which the electronic searches had not found. Two investigators independently searched, screened, and reviewed the full text of the article. Disagreements generated throughout the process were resolved by consensus, and if divergences remain, they were arbitrated by a third author. Subsequently, patients were divided into the MP and PS groups.

RESULTS

This study included 18 articles, comprising a total of 2614 patients with a similar baseline. The results showed the PS group had a higher risk of the patellar clunk or crepitus. However, the theoretical advantages of MP prosthesis could not translate to the difference in knee function, clinical complications, revision rate and satisfaction. Similarly, the shape and mechanism of prostheses could not affect the implant position and postoperative alignment.

CONCLUSIONS

The MP prosthesis can reduce the patellar clunk or crepitus rate. However, choices between the MP and PS prosthesis would not affect knee function, clinical complications, revision rate, patient satisfaction, implant position, and postoperative alignment.

Pain, balance, and mobility in people 1 year after total knee arthroplasty: a non-randomized cross-sectional pilot study contrasting posterior-stabilized and medial-pivot designs

BACKGROUND

Total knee arthroplasty (TKA) is a common treatment for severe knee osteoarthritis. Medial-pivot TKA systems (MP-TKA) are theoretically better than posterior-stabilized TKA systems (PS-TKA) in improving static and dynamic balance of patients although it is difficult to objectively quantify these balance parameters in a clinical setting. Therefore, this pilot study aimed to evaluate the feasibility of using wearable devices in a clinical setting to examine whether people with MP-TKA have better postoperative outcomes than PS-TKA, and their balance control is more akin to age-matched asymptomatic controls.

METHODS

The current cross-sectional pilot study recruited 57 participants with 2 different prosthesis designs (20 PS-TKA, 18 MP-TKA) and 19 asymptomatic controls. At 1-year post-TKA, pain, knee stiffness, and physical function were assessed using the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC). Static balance, mobility, and gait stability of the participants were evaluated based on data collected from wearable motion sensors during the near tandem stance, timed-up-and-go, and 6-min walk tests.

RESULTS

Compared to asymptomatic controls, both TKA groups reported significantly more pain and stiffness and demonstrated reduced functional mobility, increased stride-time-variability, and impaired balance. After Bonferroni adjustment, no significant differences in pain, balance, and mobility performance were observed between PS-TKA and MP-TKA participants 1 year after surgery. However, there was a trend for increased anteroposterior sway of the lumbar and head regions in the MP-TKA participants when undertaking the near tandem stance test. The wearable motion sensors were easy to use without any adverse effects.

CONCLUSIONS

It is feasible to use wearable motion sensors in a clinical setting to compare balance and mobility performance of patients with different TKA prothesis designs. Since this was a pilot study and no definite conclusions could be drawn, future clinical trials should determine the impacts of different TKA prosthesis designs on post-operative outcomes over a longer follow-up period.

Comparative Analysis of Contemporary Fixed Tibial Inserts: A Systematic Review and Network Meta-analysis of Randomized Controlled Trials

Background

Multiple options are available for the tibial insert in total knee arthroplasty (TKA). A systematic review (SR) and network meta-analysis (NMA) to compare available randomized controlled trials (RCTs) could assist with decision making. We aim to show that designs with increased conformity may improve function and satisfaction without an increase in complications though posterior stabilized (PS) inserts will likely have more flexion.

Methods

A search of MEDLINE, EMBASE, and the Cochrane Library was performed. Studies were limited to RCTs evaluating cruciate retaining (CR), PS, anterior stabilized (AS), medial pivot (MP), bicruciate retaining (BR), and bicruciate stabilizing (BCS) inserts. Mean differences (MD) were used for patient reported outcome measures (PROMs) and odds ratios (OR) for reoperation rates and MUA. A systematic review was performed for satisfaction.

Results

27 trials were identified. The NMA showed no difference from a statistical or clinical standpoint for PROMs evaluated. There was a statistical difference for increased flexion for PS knees (3 degrees p 0.04). There were no differences in the MUA or reoperation rates. There was insufficient information to determine if a specific insert improved satisfaction.

Discussion

The results of this NMA show no statistical or clinical difference in PROMs. There was higher flexion for PS knees though the amount was not clinically significant. There was insufficient data for conclusions on patient satisfaction. Therefore, the surgeon should evaluate the clinical situation to determine the best insert rather than choose and insert based on functional scores, patient satisfaction, or complication rates.

Posterior Tibial Slope Increases Anterior Cruciate Ligament Stress in Bi-Cruciate Retaining Total Knee Arthroplasty: In Vivo Kinematic Analysis

The study design involved here is experimental in nature. The resection of the anterior cruciate ligament (ACL) during conventional total knee arthroplasty (TKA) has been considered a potential factor leading to abnormal in vivo knee kinematics. Bi-cruciate retaining (BCR) TKA designs allow the preservation of the ACL with the potential to restore native knee kinematics. This study aimed to investigate the effect of posterior tibial slope (PTS) on stress experienced by the ACL during weight bearing sit-to-stand (STS) and single-leg deep lunge. The ACL elongation patterns were measured in 30 unilateral BCR TKA patients during weight-bearing STS and single-leg deep lunge using a validated dual fluoroscopic tracking technique. The minimum normalized stress within the anteromedial (AM) and posterolateral (PL) bundle of the ACL during weight-bearing STS and single-leg deep lunge was found at a PTS of 3.7 degrees. The maximum AM and PL bundle stresses were observed at a PTS of 8.5 and 9.3 degrees, respectively during STS and at 8.4, and 9.1 degrees, respectively during single-leg deep lunge. There was a significant positive correlation between PTS and stress observed within the AM and PL bundle of the ACL during weight-bearing STS (R ² = 0.37; p < 0.01; R2  = 0.36; p = 0.01) and single-leg deep lunge (R ² = 0.42; p < 0.01; R ²= 0.40; p < 0.01). The study demonstrates that PTS of operated BCR TKA knees has a significant impact on the stress experienced by the preserved ACL during weight-bearing STS and single-leg deep lunge. This suggests that avoiding excessive PTS may be one of the surgical implant alignment factors to consider during surgery to minimize increased loading of the preserved ACL.

Comparison of the clinical and patient-reported outcomes between medial stabilized and posterior stabilized total knee arthroplasty: A systematic review and meta-analysis

BACKGROUND

Total knee arthroplasty (TKA) is effective in relieving pain and improving function in patients with end-stage knee osteoarthritis. Both medial stabilized total knee arthroplasty (MS-TKA) and posterior stabilized total knee arthroplasty (PS-TKA) can achieve satisfactory clinical results, but comparisons between MS-TKA and PS-TKA have yielded contradictory conclusions. This systematic review and meta-analysis were performed to investigate the differences in clinical and patient-reported outcomes (PROMs) between MS-TKA and PS-TKA.

METHODS

In December 2020, systematic searches of the following databases were undertaken: Pubmed, Embase, Cochrane Library, Clinical Trials.gov. Studies with PROMs comparing MS-TKA to PS-TKA were included. Meta-analysis was conducted for range of motion (ROM), Knee Society Score (KSS), Knee Society Functional Score (KFS), Forgotten Joint Score (FJS), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), and Oxford Knee Score (OKS).

RESULTS

There were 17 studies included in this review, 13 studies used for quantitative analysis, and 4 studies used for qualitative synthesis. Meta-analysis concluded that the WOMAC mean difference (MD) for MS-TKA was 1.55 higher than for PS-TKA (MD = -1.55; 95 %CI = -2.45 to -0.64, P = 0.0008); however, this difference was less than the minimum clinically important difference (MCID) value of 15. Assessment using the OKS determined that the MD for PS-TKA was 0.58 higher than for MS-TKA (MD = 0.58; 95 %CI = 0.25 to 0.91, P = 0.0006); again, this MD was less than the MCID value of 5. There were no significant differences between MS-TKA and PS-TKA when assessed by ROM (P = 0.23), KSS (P = 0.13), KFS (P = 0.61), or FJS (P = 0.22).

CONCLUSION

Derived from numerous sources, utilizing a multitude of validated functional and patient-reported outcome assessment tools, there was no clinically evident advantage of MS-TKA compared to PS-TKA.

REGISTRATION

The registration number on PROSPERO is CRD42021228555.

Association of a Wider Medial Gap (Medial Laxity) in Flexion with Self-Reported Knee Instability After Medial-Pivot Total Knee Arthroplasty

BACKGROUND

Medial-pivot total knee arthroplasty (TKA) is designed with high articular conformity in the medial compartment in order to achieve stability. The subjective outcome of patients has been reported to be good postoperatively; however, the association between the objective and subjective knee stability and the influence of subjective stability on the overall outcomes of TKA remained unknown. Our hypothesis was that postoperative flexion joint-gap imbalance could affect subjective knee instability following TKA in medial-pivot prostheses. The purpose of this study was to analyze the association between the joint gap in flexion and subjective knee instability and between subjective knee instability and outcomes following medial-pivot TKA.

METHODS

A total of 769 patients who underwent primary TKA with use of medial-pivot prostheses were enrolled. Clinical outcomes included knee range of motion, Knee Society Score-2011 (KSS-2011), Forgotten Joint Score-12 (FJS-12), patient-reported subjective knee instability, and axial knee radiography to assess flexion joint-gap balance measured at the final follow-up. Clinical outcomes were compared between patients with and without subjective knee instability. Moreover, associated factors were analyzed for postoperative subjective knee instability.

RESULTS

Overall, 177 patients (23%) reported experiencing postoperative subjective knee instability. Knee flexion (p = 0.04); KSS-2011 symptom (p<0.001), satisfaction (p<0.001), expectation (p=0.008), and activity (p<0.001) subscales; and FJS-12 (p < 0.001) were significantly worse in patients with subjective knee instability. The KSS-2011 subjective score differences were greater than the minimal clinically important difference. Older age at the time of surgery (odds ratio, 1.04; p = 0.04) and a wider postoperative joint gap in flexion on the medial side (odds ratio, 1.21; p = 0.001) were significant risk factors for subjective knee instability. A gap angle of -2.9° (i.e., medial laxity) was the threshold to predict postoperative knee instability (sensitivity, 0.29; specificity, 0.91).

CONCLUSIONS

Postoperative flexion joint-gap laxity on the medial side following medial-pivot TKA affected the patient-reported subjective knee instability scores. Postoperative KSS-2011 subjective scores following medial-pivot TKA were poorer in patients with subjective knee instability.

LEVEL OF EVIDENCE

Therapeutic Level IV. See Instructions for Authors for a complete description of levels of evidence.

Obtaining anatomic motion and laxity characteristics in a total knee design

BACKGROUND

Since the introduction of the first total knee designs, a frequent design goal has been to reproduce normal knee motion. However, studies of many currently used total knee designs, have shown that this goal has not been achieved. We proposed that Guided Motion total knee designs, could achieve more anatomic motion than present standard designs.

METHODS

Several Guided Motion knees for application without cruciate ligaments were designed using a computer method where the bearing surfaces were generated by the motion required. A knee testing machine was constructed where physiological forces including compressive, shear and torque were applied during knee flexion. The neutral path of motion and the laxity about the neutral path were measured. This evaluation method was a modification of the ASTM standard Constraint Test.

RESULTS

The motions of the Guided Motion knees and a standard PS knee were compared with the anatomic motion of knee specimens determined in an earlier study The Guided Motion knees showed motion patterns which were closer to anatomic than the PS knee.

CONCLUSIONS

The results provided justification for carrying out further evaluations of functional conditions, using either knee simulators or computer modelling. If anatomic motions could be reproduced in vivo, it is possible that clinical outcomes could be improved.

Effect of weight-bearing in bicruciate-retaining total knee arthroplasty during high-flexion activities

BACKGROUND

To evaluate the effect of weight-bearing on the kinematics of the bicruciate-retaining total knee arthroplasty design during high knee flexion activities.

METHODS

The kinematics of 21 bicruciate-retaining total knee arthroplasties were evaluated under fluoroscopy, with two- and three-dimensional image registrations, during squatting (weight-bearing) and active-assisted knee flexion (non-weight-bearing). The following variables were measured: knee range of motion, axis of femoral rotation and varus-valgus angle relative to the tibial component, anteroposterior translation of the medial and lateral contact points, and the kinematic pathway of the joint surfaces.

FINDINGS

From 20° to 100° of flexion, the femoral external rotation during weight-bearing was larger than that during non-weight-bearing. There were no differences in the varus-valgus angles between the two conditions. From 10° to 50° of flexion, the medial contact point during weight-bearing was located posterior to the point of contact during non-weight-bearing; this difference between the two weight-bearing conditions was significant. From 0° to 90° of flexion, the lateral contact point in weight-bearing was located posterior to the contact point in non-weight-bearing; this difference between the two weight-bearing conditions was also significant.

INTERPRETATION

The anteroposterior position of the medial and lateral contact points of the bicruciate-retaining total knee arthroplasty design was significantly more posterior in the mid-range of knee flexion in weight-bearing than in non-weight-bearing. However, no anterior translation of the bicruciate-retaining total knee arthroplasty design was observed. Therefore, bicruciate-retaining total knee arthroplasty appears to have good anteroposterior stability throughout the range of knee flexion, regardless of the weight-bearing condition.

Medial Ball and Socket Total Knee Arthroplasty in Indian Population: 5-Year Clinical Results

Background

Medial pivot total knee arthroplasty aims to restore native knee kinematics through highly conforming medial tibiofemoral articulation with survival comparable to contemporary knee designs. The aim of this study was to report preliminary clinical results of medial pivot total knee arthroplasty in an Indian population.

Methods

A retrospective analysis of 45 patients (average age, 62 years; 40 women and 5 men) with end-stage arthritis (Kellgren-Lawrence grade 4) operated with a medial pivot prosthesis was done. All patients were assessed using Knee Society Score (satisfaction, expectation, and functional scores) and Oxford Knee Score, and range of motion was recorded at the end of 5-year postoperative follow-up. In addition, all patients underwent standardized radiological assessment.

Results

At the final follow-up, patients reported significant improvement in mean Knee Society Score (satisfaction, expectation, and functional scores) and Oxford Knee Score (p < 0.05). The mean range of motion achieved at the end of 5 years ranged from 0° (extension) to 118.4° (further flexion). There was no evidence of loosening or osteolysis at a minimum follow-up of 5 years.

Conclusions

These results demonstrated satisfactory clinical and radiological outcomes at 5 years after total knee arthroplasty with a medial pivot design, which may be related to better replication of natural knee kinematics with the medial pivot knee and inherent advantages of this design.

Medial stabilised total knee arthroplasty achieves comparable clinical outcomes when compared to other TKA designs: a systematic review and meta-analysis of the current literature

PURPOSE

The purpose of this study was to perform a systematic review and meta-analysis to compare clinical and patient-reported outcome measures of medially stabilised (MS) TKA when compared to other TKA designs.

METHODS

The Preferred Reporting Items for Systematic Review and Meta-Analyses algorithm was used. The Cochrane Central Register of Controlled Trials, MEDLINE, EMBASE, and EMCARE databases were searched to June 2020. Studies with a minimum of 12 months of follow-up comparing an MS TKA design to any other TKA design were included. The statistical analysis was completed using Review Manager (RevMan), Version 5.3.

RESULTS

The 22 studies meeting the inclusion criteria included 3011 patients and 4102 TKAs. Overall Oxford Knee Scores were significantly better (p = 0.0007) for MS TKA, but there was no difference in the Forgotten Joint Scores (FJS), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), Knee Society Score (KSS)-Knee, KSS-Function, and range of motion between MS and non-MS TKA designs. Significant differences were noted for sub-group analyses; MS TKA showed significantly worse KSS-Knee (p = 0.02) and WOMAC (p = 0.03) scores when compared to Rotating Platform (RP) TKA while significantly better FJS (p = 0.002) and KSS-knee scores (p = 0.0001) when compared to cruciate-retaining (CR) TKA.

CONCLUSION

This review and meta-analysis show that MS TKA designs result in both patient and clinical outcomes that are comparable to non-MS implants. These results suggest implant design alone may not provide further improvement in patient outcome following TKA, surgeons must consider other factors, such as alignment to achieve superior outcomes.

LEVEL OF EVIDENCE

III.

Medial pivot versus (cam post) posterior stabilised total knee arthroplasty, systematic review and meta-analysis of 3837 knees

In the current literature, there is no consensus as to whether the medial pivot (MP) or posterior-stabilised (PS) knee provides the best result for the patient in the context of post-operative range of motion (ROM) and patient reported outcome measures (PROMs). The aim of this systematic review is to provide this equipoise with some clarity. We conducted this study following both the Preferred Reporting Items for Systematic Reviews and Meta-analyses Statement (PRISMA) and the Cochrane Handbook for systematic reviews and meta-analysis. Studies comparing the MP and PS knees from all regions and written in any language were included. Twenty- one studies were included in this meta-analysis. They were prepared and analysed using Review Manager V5.0 [Computer Program] (RevMan5). We calculated the risk ratio to measure the treatment effect, taking the heterogeneity of the studies into consideration. Random-effect models were also utilised. MP knees were found to have a significant advantage over PS knees in terms of WOMAC score at the midterm follow up, and insignificant advantages over PS knees in terms of ROM and FJS at one and two years follow- up. Additionally, the PS knees demonstrated an in significantly higher Knee Society Score (KSS) at short and midterm follow up. In terms of ROM, KSS, OKS and FJS this meta-analysis suggests a non-significant advantages for the MP knee compared with the PS prothesis in the short term. The MP implant also showed a significantly superior WOMAC score at short-term follow-up. An extended follow-up period is required to evaluate whether the MP knee is superior than the PS in the long-term.

The effect of total knee geometries on kinematics: An experimental study using a crouching machine

Obtaining anatomic knee kinematics after a total knee is likely to improve outcomes. We used a crouching machine to compare the kinematics of standard condylar designs with guided motion designs. The standard condylars included femoral sagittal radii with constant radius, J-curve and G-curve; the tibial surfaces were of low and high constraint. The guided motion designs were a medial pivot and a design with asymmetric condylar shapes and guiding surfaces. The machine had a flexion range from 0° to 125°, applied quadriceps and hamstring loading, and simulated the collateral soft tissues. The kinematics of all standard condylar knees were similar, showing only small anterior-posterior displacements and internal-external rotations. The two asymmetric designs showed posterior displacements during flexion, but less axial rotations than anatomic knees. The quadriceps forces throughout flexion were very similar between all designs, reflecting similar lever arms. It was concluded that standard condylar designs, even with variations in sagittal radii, are unlikely to reproduce anatomic kinematics. On the other hand, designs with asymmetric constraint between medial and lateral sides, and other guiding features, are likely to be the way forward. The mechanical testing method could be further improved by superimposing shear forces and torques during the flexion-extension motion, to include more stressful in vivo functional conditions.

Superior patient satisfaction in medial pivot as compared to posterior stabilized total knee arthroplasty: a prospective randomized study

PURPOSE

Medial pivot (MP) total knee arthroplasty (TKA) aims to restore native knee kinematics due to highly conforming medial tibio-femoral articulation with survival comparable to contemporary knee designs. Posterior stabilized (PS) TKAs use cam-post mechanism to restore native femoral rollback. However, there is conflicting evidence regarding the reported patient satisfaction with MP TKA designs when compared to PS TKAs. The primary aim of this study is to compare the patient satisfaction between MP and PS TKA and the secondary aim is to establish potential reasons behind any differences in the outcomes noted between these two design philosophies.

METHODS

In this IRB-approved single surgeon, single centre prospective RCT, 53 patients (mean age 62 years, 42 women) with comparable bilateral end-stage knee arthritis undergoing simultaneous bilateral TKA were randomized to receive MP TKA in one knee and PS TKA in the contralateral knee. At 4 years post-surgery, all patients were assessed using Knee Society Score (KSS)-Satisfaction and -Expectation scores, and Oxford Knee Score (OKS). In addition, all the patients underwent standardized radiological and in vivo kinematic assessment.

RESULTS

Patients were more satisfied with the MP TKA as compared to PS TKA: mean KSS-Satisfaction [34.5 ± 3.05 in MP and 31.7 ± 3.16 in PS TKAs (p < 0.0001)] and mean KSS-Expectation scores [12.5 ± 1.39 in MP TKAs and 11.2 ± 1.41 in PS TKAs (p < 0.0001)]. No significant difference was noted in any other clinical outcomes. The in vivo kinematics of MP TKAs was significantly better than those of PS TKAs.

CONCLUSION

MP TKAs provide superior patient satisfaction and patient expectations as compared to PS TKA. This may be related to better replication of natural knee kinematics with MP TKA.

LEVEL OF EVIDENCE

I.

Total Knee Arthroplasty in Rheumatoid Arthritis patients with a medial stabilized prosthesis - A retrospective analysis

BACKGROUND

Total Knee Arthroplasty (TKA) has been described as an effective and successful mode of treatment in alleviation of pain and restoration of function in patients with Rheumatoid Arthritis (RA). The array of bone and soft tissue deformities in RA patients can impact initial success and long term durability of TKA. Medial Pivot (MP) prosthesis is fixed bearing asymmetric pivoting design that provides anterior-posterior stability without any post and conserves bone on the femoral side. There are few reports of suitability of experience with MP in RA.

METHODS

Twenty six patients (average age 55 years) with end stage arthritis secondary to RA operated with MP prosthesis were retrospectively followed up. At a minimum follow up of three years, all patients were assessed using Knee Society Score (KSS), Oxford Knee Score (OKS), Pain Catastrophising Scale (PCS) and radiological outcomes.

RESULTS

At final follow-up, patients reported significant improvement in mean KSS-Objective and Functional scores, Oxford Knee Score and Pain Catastrophising Scale (p < 0.05). The mean range of motion achieved at the end of two years ranged from 0 ͦ (extension) to 109.4 ͦ (full flexion). There was no evidence of loosening or osteolysis at minimum follow up of three years.

CONCLUSION

These results endorse satisfactory clinical and radiological outcomes at minimum follow up of three years following Medial Pivot Prosthetic Knee design in RA patients. Further long term follow up is needed to determine the survival analysis of MP design in these patients.

Higher patellofemoral compressive force does not affect anterior knee pain in anatomical bi-cruciate retaining total knee arthroplasty: In vivo prospective analysis of guided motion prosthesis

BACKGROUND

The purposes of the present study are 1) to measure intraoperative patellofemoral compressive force in patients undergoing anatomical bi-cruciate retaining total knee arthroplasty and to assess the relationship between intraoperative patellofemoral compressive force and patient reported outcome measurements and 2) to compare patellofemoral compressive force and patient reported outcome measurements among patients who underwent anatomical bi-cruciate retaining, cruciate retaining, and bi-cruciate stabilized total knee arthroplasty.

METHODS

Twenty-two patients with varus osteoarthritis of the knee who underwent anatomical bi-cruciate retaining total knee arthroplasty, 20 patients who underwent cruciate retaining total knee arthroplasty, and 24 patients who underwent bi-cruciate stabilized total knee arthroplasty were assessed. Patient reported outcome measurements were evaluated at 1.5 years after surgery.

FINDINGS

Intraoperative patellofemoral compressive force was significantly lower with anatomical bi-cruciate retaining total knee arthroplasty than with cruciate retaining total knee arthroplasty at 60° to 140° of flexion and nearly equivalent to intraoperative patellofemoral compressive force with bi-cruciate stabilized total knee arthroplasty at all knee flexion angles examined. With anatomical bi-cruciate retaining total knee arthroplasty, there were no significant correlations between intraoperative patellofemoral compressive force and almost all patient reported outcome measurements except for 2011 Knee Society Score expectations, which was positively correlated with patellofemoral compressive force at 10° of flexion, and Patella score quadriceps strength, which was negatively correlated with patellofemoral compressive force at 60° of flexion.

INTERPRETATION

There were no significant correlations between intraoperative patellofemoral compressive force and anterior knee pain after anatomical bi-cruciate retaining total knee arthroplasty. Evidence level: 3.

Loss of Knee Flexion and Femoral Rollback of the Medial-Pivot and Posterior-Stabilized Total Knee Arthroplasty During Early-Stance of Walking in Chinese Patients

Background The medial-pivot (MP) prosthesis was developed to produce more physiological postoperative knee kinematics and better patient satisfaction than traditional prostheses, but outcomes are inconsistent in different studies of Caucasian patients. This study aimed to investigate the postoperative patient satisfaction and in vivo knee kinematics of the MP and posterior-stabilized (PS) prosthesis during gait activity in Chinese patients.

Methods A retrospective analysis of 12 patients was received for this study in each MP group and PS group. Patient-reported satisfaction level and Forgotten Joint Score (FJS) were evaluated with questionnaires. A dual fluoroscopic imaging system was used to investigate in vivo knee kinematics of MP and PS total knee arthroplasty (TKA) during treadmill walking at a speed of 0.4 m/s.

Results Comparable promising patient satisfaction and overall FJS (MP 60.7 ± 15.35 vs. PS 51.3 ± 17.62, p = 0.174) were found between the MP and PS groups. Peak flexion appeared at around 70% of gait cycle with values of 52.4 ± 7.4° for MP and 50.1 ± 3.6° for PS groups (no difference). Both groups maintained a stable position at the stance phase and began to translated anteriorly at toe-off with an amount of 4.5 ± 2.3 mm in the MP and 6.6 ± 2.7 mm in the PS (p = 0.08) group until late swing. The range of this external rotation motion was 5.9 ± 4.8 and 6.2 ± 4.1° (p = 0.79) for the MP and PS, respectively.

Conclusion A similar knee kinematics pattern characterized by a loss of early-stance knee flexion and femoral rollback during walking was observed in the MP and PS TKAs. Our study confirmed similar effectiveness of MP TKA compared to PS TKA in Chinese patients, while the change of knee kinematics of both implants during slow walking should be noted.

Anatomical bi-cruciate retaining TKA improves gait ability earlier than bi-cruciate stabilized TKA based on triaxial accelerometery data: A prospective cohort study

Background

Total knee arthroplasty (TKA) is a common and cost-effective surgical treatment for osteoarthritis of the knee. However, only 82-89% of patients who performed TKA are satisfied with the postoperative outcomes. Therefore, bi-cruciate retaining (BCR) TKA is re-attracting attention. By retaining the anterior cruciate ligament (ACL), the knee may obtain the kinematic pathway that are closer to the native knee. The aim of the present study is to compare the ability to walk before and after surgery in patients who underwent bi-cruciate retaining total knee arthroplasty (BCR TKA) versus bi-cruciate stabilized (BCS) TKA during the early postoperative period.

Methods

Subjects included patients who underwent BCR TKA (10 knees) and BCS TKA (15 knees). We administered 10-meter gait tests before surgery and at 6 weeks and 3 months after surgery. We collected the following triaxial accelerometery data with a portable gait analyzer: walking time, number of steps, velocity, stride length, and coefficient of variability (CV) of double-leg support time while walking.

Results

Patients who underwent BCR TKA improved their gait ability [walking time (p < 0.01), number of steps (p < 0.05), velocity (p < 0.01), and stride length (p < 0.01) more than those who received BCS TKA at 6 weeks after surgery. BCR TKA improved gait ability (walking time, number of steps, velocity, and stride length) more than BCS TKA at 6 weeks after surgery. At 6 weeks after surgery, CV of double-leg support time while walking improved more in the BCR TKA group than in the BCS TKA group (p < 0.05).

Conclusions

BCR TKA is associated with improved gait ability in the early postoperative period.

Is medial pivot total knee arthroplasty suitable for patients with valgus knee osteoarthritis?

PURPOSE

Medial pivot total knee arthroplasty (MP-TKA) is characterized by the ball-in-socket medial tibiofemoral articulation to achieve low wear and to reproduce the medial pivot motion similar to that in the normal knee, and there have been reports of favorable long-term postsurgical outcomes. However, most of these cases concerned varus knees, and the outcomes of MP-TKA in valgus knees are unknown. The objective of this study was to investigate the postoperative outcomes in end-stage valgus knee OA patients who underwent MP-TKA, through comparisons with those who underwent TKA using the same prosthesis for varus deformity.

METHODS

This retrospective, single-center, cohort study analyzed 171 knees of 121 patients who were divided into two groups (valgus knee group: 15 knees (13 patients), varus knee group: 156 knees (109 patients)). Primary outcome measures included the knee joint range of motion (evaluated preoperatively and at every year postoperatively). Secondary outcomes included operative time, laboratory data, estimated blood loss, clinical outcome measures and adverse events.

RESULTS

There were no significant differences in age, sex and body mass index, as well as in the postoperative primary and secondary outcome measures between the two groups.

CONCLUSION

The use of MP-TKA featuring ball-in-socket medial tibiofemoral articulation in patients with valgus knee OA showed equally favorable clinical outcomes more than 2 years after surgery, compared to patients with varus knees who received MP-TKA.

A Prospective Randomized Controlled Trial Comparing Medial-Pivot versus Posterior-Stabilized Total Knee Arthroplasty

BACKGROUND

The medial-pivot (MP) design for total knee arthroplasty (TKA) aims to restore more natural "ball-and-socket" knee kinematics compared to the traditional posterior-stabilized (PS) implants for TKA. The objective of this study is to determine if there was any difference in functional outcomes between patients undergoing MP-TKA vs PS-TKA.

METHODS

This prospective randomized controlled trial consisted of 43 patients undergoing MP-TKA vs 45 patients receiving a single-radius PS-TKA design. The primary outcome was postoperative range of motion (ROM). Secondary outcomes included the Western Ontario and McMaster Universities Arthritis Index, Oxford Knee Score, Knee Society Score (KSS), and radiological outcomes. All study patients were followed-up for 2 years after surgery.

RESULTS

Patients undergoing MP-TKA had comparable ROM at 1 year (114.6° ± 16.3° vs 111.3° ± 17.8° respectively, P = .88) and 2 years after surgery (114.9° ± 15.5° vs 114.9° ± 16.4° respectively, P = .92) compared to PS-TKA. There were also no differences in Western Ontario and McMaster Universities Arthritis Index (26.8 ± 19.84 vs 22.0 ± 12.03 respectively, P = .14), Oxford Knee Score (42.7 ± 8.1 vs 42.3 ± 6.7 respectively, P = .18), KSS clinical scores (82.9 ± 16.96 vs 81.42 ± 10.45 respectively, P = .12) and KSS functional scores (76.2 ± 18.81 vs 73.93 ± 8.53 respectively, P = .62) at 2-year follow-up. There was no difference in postoperative limb alignment or complications.

CONCLUSION

This study demonstrated excellent results in both the single-radius PS-TKA design and MP-TKA design. No differences were identified at 2-year follow-up with respect to postoperative ROM and patient-reported outcome measures.

Patient-specific musculoskeletal models as a framework for comparing ACL function in unicompartmental versus bicruciate retaining arthroplasty

Unicompartmental knee arthroplasty has been shown to provide superior functional outcomes compared to total knee arthroplasty and have motivated development of advanced implant designs including bicruciate retaining knee arthroplasty. However, few validated frameworks are available to directly compare the effect of implant design and surgical techniques on ligament function and joint kinematics. In the present study, the subject-specific lower extremity models were developed based on musculoskeletal modeling framework using force-dependent kinematics method, and validated against in vivo telemetric data. The experiment data of two subjects who underwent TKA were obtained from the SimTK "Grand Challenge Competition" repository, and integrated into the subject-specific lower extremity model. Five walking gait trials and three different knee implant models for each subject were used as partial inputs for the model to predict knee biomechanics for unicompartmental, bicruciate retaining, and total knee arthroplasty. The results showed no significant differences in the tibiofemoral contact forces or angular kinematic parameters between three groups. However, unicompartmental knee arthroplasty demonstrated significantly more posterior tibial location between 0% and 40% of the gait cycle (p < 0.017). Significant differences in range of tibiofemoral anterior/posterior translation and medial/lateral translation were also observed between unicompartmental and bicruciate retaining arthroplasty (p < 0.017). Peak values of anterior cruciate ligament forces differed between unicompartmental and bicruciate retaining arthroplasty from 10% to 30% of the gait cycle. Findings of this study indicate that unicompartmental and bicruciate retaining arthroplasty do not have identical biomechanics and point to the complementary role of anterior cruciate ligament and articular geometry in guiding knee function. Further, the patient-specific musculoskeletal model developed provides a reliable framework for assessing new implant designs, and effect of surgical techniques on knee biomechanics following arthroplasty.

A Medial Congruent Polyethylene Offers Satisfactory Early Outcomes and Patient Satisfaction in Total Knee Arthroplasty

Background

Although a successful operation, almost 20% of patients are dissatisfied with total knee arthroplasty (TKA). The purpose of this retrospective cohort study was to see if a medial congruent (MC) polyethylene would offer satisfactory early outcomes and patient satisfaction after TKA.

Methods

We reviewed prospectively collected data on 327 TKAs using multiple bearings within the same implant system. Ninety-six received an MC bearing, 70 received a cruciate-retaining (CR) bearing, and 161 received a posterior-stabilized (PS) bearing. We evaluated the visual analog scale pain scores and range of motion (ROM) at 2 weeks, 6 weeks, 3 months, and 1 year; Patient-Reported Outcomes Measurement Information System (PROMIS-10) score and Knee Injury and Osteoarthritis Outcome Score (KOOS) at 3 months and 1 year; and Forgotten Joint Score (FJS-12) at 1 year.

Results

All groups had similar KOOS and PROMIS-10 scores. MC knees had lower visual analog scale scores than PS knees at all time points (P < .05) and a higher ROM than PS at 2 weeks (98.6 vs 93.7, P = .002). MC knees had a significantly higher FJS-12 than CR knees (71.6 vs 58.7, P = .02). More MC knees were “very satisfied” than CR (92.6% vs 81.5%, P = .04). Fewer MC knees were “not at all satisfied” than CR (1.2% vs 9.2%, P = .04). There were similar satisfaction ratings with MC and PS.

Conclusions

An MC bearing provided similar or improved early pain, ROM, KOOS, PROMIS-10, FJS-12, and patient satisfaction as compared with standard bearings in TKA.

In vivo kinematics and cruciate ligament forces in bicruciate-retaining total knee arthroplasty

We analyzed the effects of bicruciate-retaining total knee arthroplasty (BCR-TKA) on knee kinematics and cruciate ligament forces. Patients (N = 15) with osteoarthritis (OA) and an intact anterior cruciate ligament (ACL) underwent magnetic resonance imaging and single-plane fluoroscopy to measure tibiofemoral kinematics during two deep knee bend activities before and after BCR-TKA: (1) weight-bearing squat; (2) non-weight-bearing cross-legged sitting. Forces in ligament bundles were calculated using VivoSim. The dynamic range of varus-valgus angulation decreased from 3.9 ± 4.4° preoperatively to 2.2 ± 2.7° postoperatively. Preoperatively, the medial femoral condyle translated anteriorly from 10° to 50° of flexion, and posteriorly beyond 50° of flexion. Postoperatively, the medial and lateral femoral condyles translated posteriorly throughout flexion in a medial pivot pattern. ACL forces were high in extension and decreased with flexion pre- and postoperatively. PCL forces increased with flexion preoperatively and did not change significantly postoperatively. Preoperatively, ACL forces correlated with anteroposterior translation of the femoral condyles. Postoperatively, PCL forces correlated with anteroposterior translation of the lateral femoral condyle. BCR-TKA altered knee kinematics during high flexion activity which correlated significantly with changes in cruciate ligament forces.

In Vivo Kinematics of Bicruciate-Retaining Total Knee Arthroplasty with Anatomical Articular Surface under High-Flexion Conditions

Bicruciate-retaining total knee arthroplasty (BCR-TKA) recreates normal knee movement by preserving the anterior cruciate and posterior cruciate ligaments. However, in vivo kinematics of BCR-TKA with the anatomical articular surface remains unknown. The objective of this study was to evaluate in vivo kinematics of BCR-TKA with the anatomical articular surface during high-flexion activities. For this purpose, 17 knees after BCR-TKA with an anatomical articular surface were examined. Under fluoroscopy, each patient performed squatting and cross-legged sitting motions. To estimate the spatial position and orientation of the knee, a two-dimensional or three-dimensional registration technique was used. Rotation, varus-valgus angle, and anteroposterior translation of medial and lateral contact points of the femoral component relative to the tibial component were evaluated in each flexion angle. The results showed that from 80 to 110° of flexion, the femoral external rotation during squatting was significantly larger than that during cross-legged sitting. At maximum flexion, the knees during sitting indicated significantly more varus alignment than during squatting. During squatting, a medial pivot pattern was observed from minimum flexion to 10° flexion, with no significant movement beyond 10° of flexion. Conversely, during cross-legged sitting, no significant movement was detected from minimum flexion to 60° of flexion, with a medial pivot beyond 60° of flexion. Therefore, the knees showed relatively normal kinematics after BCR-TKA with an anatomical articular surface; however, it varied during high-flexion activities depending on the activity.

Clinical and Patient-Reported Outcomes of Medial Stabilized Versus Non-Medial Stabilized Prostheses in Total Knee Arthroplasty: A Systematic Review and Meta-Analysis

BACKGROUND

The aim of this systematic review and meta-analysis was to compare the clinical and patient-reported outcome measures (PROMs) of medial stabilized total knee arthroplasty (TKA) with non-medial stabilized TKAs.

METHODS

A systematic search of multiple databases was conducted in October 2019. A meta-analysis was conducted for the Knee Society Score (KSS), Knee Society Functional Score (KFS), range of motion (ROM), Oxford Knee Score (OKS), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), and Forgotten Joint Score (FJS).

RESULTS

A total of 857 articles yielded 21 studies eligible for inclusion with 13 studies used for quantitative analysis. The meta-analysis revealed that the medial stabilized group had a mean FJS that was 13.8 points higher than that of the non-medial stabilized TKA (mean difference [MD]: 13.83, P ≤ .0001, 95% confidence interval [CI]: 8.90-18.76, I² = 0%) which was less than the minimal clinically important difference of 14. The medial stabilized group also demonstrated a statistically significant difference in the postoperative ROM (MD = 2.52, P = .05, 95% CI: -0.03 to 5.07, I² = 85%) and OKS when compared with the non-medial stabilized group (MD = 1.25, P = .02, 95% CI: 0.17-2.33, I² = 27%), but these were not clinically significant. There was no statistically or clinically significant difference in the KSS, KFS, and WOMAC scores.

CONCLUSION

Medial stabilized knee prostheses demonstrated no clinically significant differences for the ROM, OKS, WOMAC, KSS, and KFS. The FJS demonstrated the greatest MD and warrants further investigation. Future research is required using patient-reported outcome measures with a lower ceiling effect such as the FJS.

Bi-cruciate retaining total knee arthroplasty: a systematic literature review of clinical outcomes

Total knee arthroplasty (TKA) has been shown to have good long-term outcomes and survivorship. Nonetheless, dissatisfied patients are frequently reported in the literature. Bi-cruciate retaining total knee prostheses (BCR TKA) were designed to address the demand for more kinematically functional implants that better reconstruct natural knee kinematics. In BCR TKA, the anterior cruciate ligament (ACL) is preserved. Improved patient-reported outcomes and satisfaction levels are expected. This review aimed to summarize indications for and clinical outcomes of BCR TKA. A systematic literature review on BCR TKA was performed. 24 articles were included for data analysis. Indications covered osteoarthritis, inflammatory arthritis and others. The degree of deformity was often but not always limited to minor axial deformity and contractures: maximum acceptable varus/valgus deformity reached 10°-30° and flexion contractures of 15°-65°. ACL intactness was macroscopically examined intraoperatively in nine studies and clinically tested in ten studies (e.g., Lachmann Test, drawer-test). Objective and patient-reported outcome scores were reported for follow-up periods of up to 22 years. Survival rates varied significantly. For first generation implants, 22-year survival reached 82% while a second generation design was associated with 13.5% revision rate at 18 months. Reasons for varying outcomes were not clear and may be attributed to the implant itself, surgical techniques and patient specific variables including changed expectations and functional demand. The literature has not shown clear indications and guidelines for the use of BCR implants. The promising results of first generation BCR TKA designs may be optimized through improved implant designs in the future. Further studies are advocated to provide the necessary evidence of second generation BCR TKA designs.

The Medial Rotation Knee replacement: Clinical and radiological results of a multi-centre surveillance study at five years

BACKGROUND

The Medial Rotation Knee (MRK) has one of the lowest revision rates of total knee replacement designs in the National Joint Registry. While survival is one metric of performance of implants, patient-reported outcomes, combined with clinical and radiological evaluation, allow more complete analysis. We report the five-year results of a prospective, multi-centre surveillance study of the MRK.

METHODS

A 16-surgeon, three-centre series of 520 total knee replacements were performed in 486 patients, comprising 182 males and 304 females. The mean age was 70.3 years (46-96) and BMI 29.5 kg/m² (18-57). Study subjects were given questionnaires pre-operatively, at six months, and annually thereafter. Clinical and radiological reviews were scheduled pre-operatively, at six months, three and five years.

RESULTS

At five years, 395 of the original 486 patients (427 of 520 knees) remained under active review. Twenty-six patients (27 knees) had withdrawn, 44 patients/knees had died and one was excluded. Thirteen patients (14 knees) were lost to follow-up, but were not revised. Seven knees were revised, equating to a survival probability of 98.6% at five years. There were significant improvements in mean Oxford Knee Score (21.23-35.79), EQ-5D (0.440-0.694) and Knee Society Score (Knee 43.00-83.97; Function 49.45-71.39). Of the radiographs available for evaluation, radiolucency was identified in 25 knees (14.6%) with one case of osteolysis of the tibial component.

CONCLUSION

In addition to excellent survivorship, mid-term patient-reported, clinical and radiological results at five years are satisfactory, and consistent with other medial pivot designs.

Insufficient lateral joint laxity after bicruciate-retaining total knee arthroplasty potentially influences kinematics during flexion: A biomechanical cadaveric study

BACKGROUND

Soft tissue balancing in bicruciate-retaining (BCR) total knee arthroplasty (TKA) is a challenge that must be overcome to achieve excellent clinical outcomes. However, the optimal degree of joint laxity has yet to be clarified. This cadaveric study sought to examine joint laxity after BCR TKA using a navigation system.

METHODS

Knee joint laxity was quantified using an image-free navigation system in 8 intact fresh frozen cadavers under three conditions: the native knee, BCR TKA knee, and BCR TKA knee after anterior cruciate ligament resection. Rotational kinematics in the BCR TKA knee during flexion were compared according to whether joint laxity was increased or decreased.

RESULTS

Knee joint laxity after BCR TKA under varus-valgus movement, anterior translation, and internal-external rotation loadings was similar to that of the native knee. However, lateral joint laxity was decreased during flexion in some cases. BCR TKA-treated knees with decreased lateral joint laxity at 90° of flexion demonstrated more limited tibial internal rotation in deep flexion than the native knee (p < 0.05). The loss of internal rotation in deep flexion was partly recovered by using a lateral insert with a posterior slope of +3°.

CONCLUSIONS

Restoring optimal joint laxity was not always straightforward in BCR TKA if the 4 ligaments were preserved. Lateral joint laxity was potentially decreased in BCR TKA and may result in kinematic conflict during flexion. Surgeons should be aware of the need to achieve sufficient lateral joint laxity in this type of BCR TKA.

No difference in patient preference for medial pivot versus posterior-stabilized design in staged bilateral total knee arthroplasty: a prospective study

PURPOSE

Medial pivot (MP) TKA has been shown to mimic normal knee kinematics with long-term survivorship comparable to most contemporary TKA. However, there are inadequate evidences to suggest its superiority in terms of patient preference and satisfaction. The aim of this study is to compare the MP with posterior-stabilized (PS) TKA in terms of patient preference and satisfaction.

METHODS

46 patients with staged bilateral TKA were recruited. TKA with MP or PS design was performed at interval of 6-12 months. Patient preference, patient satisfaction score (0-100), Forgotten Joint Score (FJS), range of motion (ROM), Pain Score, Knee Society Score (KSS), Knee Function Score (KFS) and WOMAC Score were compared at up to 12 months.

RESULTS

The mean age was 70 and 69.6% were female. There was no difference in all preoperative parameters, operative time and length of stay between two knees. No difference was found in in range of motion and all outcome scores at 6 months and 12 months. Satisfaction score was similar for the two designs (82 vs 85, p = n.s.) at 1 year after the second TKA. Proportion of patients with preference on one design over another was not significantly different (28.9 vs 35.6%, p = n.s.).

CONCLUSIONS

There is no evidence to support the superiority of MP TKA over PS TKA in terms of preference and satisfaction. The choice between MP TKA versus PS TKA maybe more a surgeon's preference than a patient's preference based on current evidence.

Long-term clinical outcomes of medial pivot total knee arthroplasty for Asian patients: A mean 10-year follow-up study

BACKGROUND

Many Asian populations have a unique floor-based lifestyle that might cause mechanical stress of the knees. It is important to clarify the longevity of a medial pivot total knee arthroplasty, as its prosthetic design could cause mechanical stress onto the insert. The purpose of this study was to clarify the clinical results of medial pivot total knee arthroplasty for Asian patients in a 10-year follow-up study.

METHODS

Consecutive, primary total knee arthroplasties (n = 257) were analyzed in the study using the medial pivot knee system. The clinical outcomes were assessed preoperatively and at the final follow-up. The patient-reported Forgotten Joint Score-12 and radiological outcomes were measured at the final follow-up. The survival rate was assessed with reoperation or revision as the end-point.

RESULTS

The mean follow-up period was 10.1 ± 1.7 years. The lost to follow-up was 4.5%. All clinical outcomes improved significantly after surgery (p < 0.001). The mean postoperative knee flexion was 118° ± 11° and the mean Forgotten Joint Score-12 was 59.7 ± 27 points. The radiolucent line was observed in 29 patients (11.3%), however there was no aseptic loosening noted. The survival rates with reoperation or revision were 96.3% or 98.4% at 10 years after the operation.

CONCLUSIONS

Medial pivot total knee arthroplasty used for Asian patients showed good longevity and patient-reported outcome measurement in a mean 10-year follow-up study. Medial pivot total knee arthroplasty has long-term stability among patients who have a floor-based lifestyle.

LEVEL OF EVIDENCE

III.