Total Knee Arthroplasty Kinematics

Anterior Position of the Femoral Condyle During Mid-Flexion Worsens Knee Activity After Cruciate-Retaining Total Knee Arthroplasty

BACKGROUND

The effects of kinematics on patient-reported outcome measures (PROMs) after cruciate-retaining (CR) total knee arthroplasty (TKA) remain unclear. This study investigated the effects of kinematic patterns after CR-TKA on PROMs.

METHODS

We examined 35 knees (27 patients) undergoing primary CR-TKA. Knee kinematics and 2011 Knee Society Score were evaluated at a mean follow-up of 72.4 (± 28.2) months. Knee kinematics was analyzed using fluoroscopy, and the femoral antero-posterior position relative to the tibial component was assessed separately for medial and lateral compartments during a squat. The correlations between kinematics and PROMs were evaluated.

RESULTS

The average amount of posterior femoral translation from full extension to maximum flexion was 0.2 (± 2.6) mm for the medial femoral condyle and 4.1 (± 2.9) mm for the lateral condyle. Medial pivot motion was observed in 24 knees (68.6%) with a low rate (14.3%) of paradoxical anterior translation. The anterior position of the medial femoral condyle at 60° had a negative impact on discretionary activities (ρ = -0.37; P = .039), and at maximum flexion, had a negative impact on total functional activities (ρ = -0.46; P = .005), advanced activities (ρ = -0.45; P = .006), and discretionary activities (ρ = -0.63; P < .001). Anterior position of the lateral femoral condyle at 30° had a negative impact on total functional activities (ρ = -0.48; P = .005), walking and standing (ρ = -0.56; P < .001), and advanced activities (ρ = -0.49; P = .004), and at 60° had a negative impact on walking and standing (ρ = -0.45; P = .010).

CONCLUSIONS

The anterior positions of the medial and lateral femoral condyles at mid-flexion and maximum flexion had negative impacts on PROMs. Soft tissue conditions should be carefully managed to achieve medial knee joint stability, which can improve PROMs.

Achieving Specified Laxity in a Noncruciate Total Knee: A Laboratory Design Study

BACKGROUND

Noncruciate total knee arthroplasty designs, including ultracongruent, medially congruent, and medial pivot, are gaining increasing attention in total knee arthroplasty surgery. However, there is no consensus for the bearing surface design, whether there should be different medial, lateral, anterior, and posterior laxities, or whether the medial side should be a medial pivot. This study proposes the criterion of reproducing the laxity of the anatomic knee, defined as the displacements and rotations of the femur on the tibia in the loaded knee when shear and torque are applied. The purpose of this study was to determine the ideal tibial radii to achieve that goal.

METHODS

The femoral component was based on the average knee from 100 mild arthritic knee scans. There were 8 tibial components that were designed with different sagittal radii: antero-medial, antero-lateral, postero-medial, and postero-lateral. Radii were defined as the percent height reduction from full conformity with the femoral profile. Components were 3-dimensional-printed. A test rig was constructed where the tibial component was fixed and shear and torque were applied to the femoral component. Displacements and rotations of the femoral component were measured at 0 and 45° of flexion, the latter representing any flexion angle due to the constant femoral sagittal radius.

RESULTS

Displacements ranged from 0 to 11 mm, and rotations ranged from 1 to 11°. Anterior femoral displacements were higher than posterior due to the shallow distal-anterior femoral profile. The final femoral and tibial components with the most closely matched anatomic laxity values were designed and tested.

CONCLUSIONS

A steeper distal-anterior femoral radius was an advantage. High medial-anterior tibial conformity was important. However, on the lateral side, the posterior sagittal tibial radius had to be shallower than ideal to allow femoral rollback in high flexion. This meant that the posterior laxity displacements on the lateral side were higher than anatomic, and there was no guidance for lateral femoral rollback.

Effect of Surgical Technique, Implant Design, and Time of Examination on Contact Kinematics: A Study of Bicruciate-Stabilized and Posterior-Stabilized Total Knee Arthroplasty

BACKGROUND

Bicruciate-stabilized (BCS) total knee arthroplasty (TKA) designs attempt to approximate natural knee mechanics. Multiple surgical techniques, including gap balancing (GB) and measured resection (MR), have been developed to provide optimal implant positioning and soft-tissue balance. The goal of this study was to determine the effect of surgical technique on BCS TKA contact kinematics. Secondary goals included investigating the change of kinematics over time and comparing BCS TKA kinematics to a posterior-stabilized (PS) design.

METHODS

The study included the BCS-GB, BCS-MR, and PS-MR groups. The BCS-GB and BCS-MR groups underwent weight-bearing radiostereometric analysis for multiple knee flexion angles at 3 months and 1 year postoperatively, whereas the PS-MR group was imaged at 1 year postoperatively. The medial and lateral contact kinematics were determined from implant poses.

RESULTS

There were no differences in BCS TKA kinematics between the GB and MR techniques. There were differences in the mid-flexion ranges when comparing the 3-month and 1-year kinematics of the BCS design; however, they were less than 1.5 mm. Differences existed between the kinematics of the BCS and PS designs at all flexion angles for the medial condyle (P < .0006) and at 0° of flexion on the lateral condyle (P < .0001).

CONCLUSIONS

Contact kinematics for a BCS design were similar for both surgical techniques, suggesting both are appropriate for this design. Small, likely clinically insignificant differences were found between 3-month and 1-year kinematics. The BCS TKA kinematics differed from the PS design; however, it is unclear whether these differences improve clinical outcomes.

Objective Clinical Measurement Tools for Functional Evaluation of the Surgical Patient

Following knee surgery, clinicians have traditionally used visually rated or time-based assessments of lower extremity movement quality to measure surgical outcomes, plan rehabilitation interventions, and measure success. These methods of assessment are prone to error and do not fully capture a patient's inefficient movement patterns post surgery. Further, currently available systems which objectively measure kinematics during these tasks are expensive and unidimensional. For these reasons, recent research has called for the development of objective and low-cost precision rehabilitation tools to improve clinical measurement of movement tasks. The purpose of this article is to highlight two such tools and their applications to knee surgery. The systems highlighted within this article are the Mizzou Point-of-Care Assessment System (MPASS) and the Mizzou Knee Arthrometer Testing System (MKATS). MPASS has demonstrated high levels of agreement with the gold-standard Vicon system in measuring kinematics during sit-to-stand (R > 0.71), lateral step-down (intraclass correlation coefficient [ICC] > 0.55, apart from ankle flexion), and drop vertical jump tasks (ICC > 0.62), as well as gait (R > 0.87). MKATS has been used to quantify differences in tibiofemoral motion between groups during lateral step-down, step-up-and-over, and step-up/step-down tasks. Objective measurement of clinical tasks using portable and inexpensive instruments, such as the MPASS and MKATS, can help clinicians identify inefficient movement patterns and asymmetries which may damage and wear down supporting structures within the knee and throughout the kinetic chain causing pain and discomfort. Identifying these issues can help clinicians to plan interventions and measure their progress at a lower cost than currently available systems. The MPASS and MKATS are useful tools which have many applications to knee surgery.

Lateral Subvastus Lateralis versus Medial Parapatellar Approach for Total Knee Arthroplasty: Patient Outcomes and Kinematics Analysis

The conventional approach for total knee arthroplasty (TKA) is a medial parapatellar approach (MPA). We aimed to study patient outcomes and kinematics with a quadriceps sparing lateral subvastus lateralis approach (SLA). Patients with neutral/varus alignment undergoing primary TKA were consented to undergo the SLA. At 1-year postoperative, patients underwent radiostereometric analysis. Patients were administered the Short Form 12 (SF-12), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), and Knee Society Score (KSS). Kinematics and outcome data were compared to a group undergoing TKA via conventional MPA. Fourteen patients underwent TKA via SLA with a mean age 71.5 ± 8.0 and mean body mass index (BMI) 31.0 ± 4.5. The MPA group had 13 patients with mean age 63.4 ± 5.5 (p = 0.006) and mean BMI 31.2 ± 4.6 (p = 0.95). The SLA resulted in a significantly more posterior medial contact point at 0 (p = 0.011), 20 (p = 0.020), and 40 (p = 0.039) degrees of flexion. There was no significant difference in medial contact point from 60 to 120 degrees, lateral contact point at any degree of flexion, or axial rotation. There was no difference in improvement in postoperative WOMAC, SF-12, KSS function, and total KSS knee scores between groups. The MPA group had a significantly greater improvement in KSS knee scores at 3 months (p < 0.001), 1 year (p = 0.003), and 2 years (p = 0.017). The SLA resulted in increased medial femoral rollback early in flexion. Although both approaches resulted in improved postoperative outcomes, the MPA group showed significantly greater improvements in KSS knee scores at 3 months, 1 year, and 2 years. Further studies are required to identify any benefits that the SLA may offer. LEVEL OF EVIDENCE:  Therapeutic Level II.

Tibiofemoral articulation and axial tibial rotation of the knee after a cruciate retaining total knee arthroplasty

PURPOSE

Numerous research has reported that total knee arthroplasty (TKA) cannot reproduce axial tibial rotations of normal knees. The objective of this study was to measure the tibiofemoral articular contact motions and axial tibial rotations of TKA knees to investigate the mechanism causing the knee kinematics change of after TKAs.

METHODS

Eleven patients with unilateral cruciate retaining (CR) TKA were tested for measurements of knee motion during a weight-bearing flexion from 0° to 105° using an imaging technique. The tibiofemoral contact kinematics were determined using the contact points on medial and lateral surfaces of the tibia and femoral condyles. Axial tibial rotations were calculated using the differences between the medial and lateral articulation distances on the femoral condyles and tibial surfaces at each flexion interval of 15°.

RESULTS

On femoral condyles, articular contact distances are consistently longer on the medial than on the lateral sides (p < 0.05) up to 60° of flexion, corresponding to internal tibial rotations (e.g., 1.3° ± 1.0° at 15-30° interval). On tibial surfaces, the articular contact point on the medial side moved more posteriorly than on the lateral side at low flexion angles, corresponding to external tibial rotations (e.g., -1.4° ± 1.8° at 15-30° interval); and more anteriorly than on the lateral sides at mid-range flexion, corresponding to internal tibial rotations (e.g., 0.8° ± 1.7° at 45-60° interval). At higher flexion, articular motions on both femoral condyles and tibial surfaces caused minimal changes in tibial rotations.

CONCLUSIONS

These results indicate that the axial tibial rotations of these TKA knees were mainly attributed to asymmetric articulations on the medial and lateral femoral condyles and tibial surfaces. The data can help understand the mechanisms causing axial tibial rotations of TKA knees and help improve implant designs for restoration of normal knee kinematics.

Knee kinematics are not different between asymmetrical and symmetrical tibial baseplates in total knee arthroplasty: A fluoroscopic analysis of step-up and lunge motions

PURPOSE

This clinical fluoroscopy study investigated knee kinematics of two different cemented fixed-bearing, posterior-stabilised (PS) total knee arthroplasty (TKA) designs: an asymmetric tibial component including an asymmetric insert designed to optimise personalised balance and fit and its precursor symmetrical design with symmetric insert.

METHODS

A consecutive series of patients (16 TKAs from each treatment group) participating in a randomised controlled trial comparing TKA migration was included. The exclusion criterion was the use of walking aids. Flat-panel fluoroscopic recordings of step-up and lunge motions were acquired 1-year postoperatively. Medial and lateral contact points (CPs) were determined to calculate CP displacement, femoral axial rotation and pivot position. Using linear mixed-effects modelling techniques, kinematics between TKA designs were compared.

RESULTS

During knee extension between 20° flexion and full extension, the CPs moved anteriorly combined with a small internal femoral rotation (a screw-home mechanism). Whereas CP movement was reversed: femoral rollback, external femoral rotation while flexing the knee between full extension and 20° knee flexion, At larger flexion angles, femoral axial rotation (FAR) occurred around a lateral pivot point both during step-up and lunge. The symmetric design had a 2.3° larger range of FAR compared to the asymmetric design during lunge (p = 0.02). All other kinematics were comparable.

CONCLUSION

Despite the differences in design, this study showed that the asymmetric and symmetric PS TKA designs had mostly comparable knee kinematics during step-up and lunge motions. It is therefore expected that the functionality of the successor TKA design is similar to that of its precursor design.

LEVEL OF EVIDENCE

Level II, prospective comparative study.

Significantly better precision with new machine learning versus manual image registration software in processing images from single-plane fluoroscopy to determine tibiofemoral kinematics following total knee replacement

One common method to determine tibiofemoral kinematics following total knee replacement (TKR) is to capture single-plane fluoroscopic images of a patient activity and determine anterior-posterior (AP) positions of the femoral condyles and internal-external (IE) tibial rotation. Although JointTrack is widely used to analyze such images, precision (i.e. repeatability) in determining AP positions and IE tibial rotations using the two publicly available programs has never been quantified. The objectives were to determine the precision and reproducibility of results using both programs. Fluoroscopic images of 16 patients who performed a weight-bearing deep knee bend following TKR were analyzed. JointTrack Manual (JTM) and JointTrack Machine Learning (JTML) were used to perform 3D model-to-2D image registration after which AP positions of the femoral condyles and IE tibial rotations were determined. Precision in AP positions and IE rotations was quantified. Intraclass correlation coefficients (ICCs) for both repeatability (i.e. intraobserver) and reproducibility (i.e. interobserver) also were determined. Precision using JTM was worse than JTML for AP positions of the medial and lateral femoral condyles (1.0 mm and 0.9 mm vs 0.3 mm and 0.4 mm, respectively; p < 0.001 for both). For IE tibial rotation, precision also was worse using JTM versus JTML (1.1º vs 0.9°, p = 0.010). ICC values for JTML indicated good to excellent agreement (range: 0.82-0.98) whereas ICC values for JTM indicated only moderate to good agreement (range: 0.58-0.88). JTML has better precision and reproducibility than JTM and also is more efficient to use. Therefore, use of JTML over JTM is strongly recommended.

Higher rates of fully preserved posterior cruciate ligament in total knee arthroplasty using a double tibial cut: a prospective randomized controlled trial

PURPOSE

In cruciate retaining total knee arthroplasty, posterior cruciate ligament damage may occur during tibial cutting. A prospective randomized study was conducted to investigate whether a novel tibial cutting technique was more effective than the currently used techniques.

MATERIALS AND METHODS

Patients undergoing cruciate retaining total knee arthroplasty were recruited in a prospective, randomized, controlled trial. In 25 patients (group 1) the tibial cut was performed using a double tibial cut technique; in 25 (group 2) and 25 (group 3) patients, the bone island and en bloc resection techniques were performed, respectively. Posterior cruciate ligament integrity and femoral rollback were assessed at the end of surgery. The Oxford Knee Score, WOMAC score and range of motion were assessed postoperatively.

RESULTS

Posterior cruciate ligament was completely preserved in 92% of patients in group 1 and in 64% in group 2 and 3, respectively (p = 0.03). The Oxford Knee Score and WOMAC scores did not differ between groups (p = 0.4). The mean knee flexion was 126.4°, 121.5° and 123.9° in groups 1, 2 and 3, respectively (p = 0.04). The femoral rollback at 120° flexion was 80.7%, 72.2% and 75.4% in groups 1, 2 and 3, respectively (p = 0.01).

CONCLUSIONS

The double cut technique preserves the posterior cruciate ligament at significantly higher rates than the bone island or en bloc resection techniques. Better posterior cruciate ligament preservation may improve the femoral rollback and knee flexion.

LEVEL OF EVIDENCE

Prospective randomized controlled trial, Level I.

Improvement of rotational arc during deep flexion range of a novel designed polyethylene insert for posterior-stabilised total knee arthroplasty

BACKGROUND

One of the remaining issues in total knee arthroplasty (TKA) is achieving sufficient rotational arc during deep flexion range of the knee for specific postures such as the 'seiza' or cross-legged sitting. This study aimed to evaluate whether there was a change in the actual in vivo rotational arc during deep flexion range before and after a design change of polyethylene (PE) inserts.

METHODS

In 50 posterior-stabilised TKA cases, knee kinematics, including rotational movement, were measured intraoperatively using an image-free navigation system to compare a newly designed PE insert with reduced the posterior lip with a conventional PE insert. Femoral-tibial rotational angles at 30°, 45°, 60°, 90°, 120°, and 130° knee flexion were evaluated. Varus/valgus instability, knee range of motion, and femoral rollback were also measured. Obtained parameters were compared between new and conventional PE inserts. The independent factors associated with rotational arc during deep flexion range (120° and 130° knee flexion) were analysed using multivariate analysis.

RESULTS

The newly designed PE insert demonstrated a significant increase in the rotational arc at 120° (22.9 ± 8.7° vs. 30.1 ± 11.9°, P < 0.001) and 130° (24.3 ± 9.5° vs. 32.5 ± 12.4°, P < 0.001) knee flexion compared with that with the conventionally designed posterior-stabilised insert. Multivariate analysis demonstrated that using the newly designed PE insert was an independent predictor of improved rotational arc during deep flexion range: regression coefficient was 11.2 (95% confidence interval 7.1-15.3, P < 0.001).

CONCLUSION

The design change, which reduced the posterior lip of the PE insert, contributed to improved rotational arc in 120° and 130° deep flexion ranges.

Efficacy of acupuncture therapy for spastic paralysis in post-stroke patients: a systematic review and meta-analysis

BACKGROUND

Despite the potentially good efficacy of acupuncture therapy in the management of post-stroke spastic paralysis demonstrated in previous studies, further verification through meta-analysis can be conducive to eliminating the inconclusive of treatment outcomes in prior findings. This systematic review and meta-analysis were thus performed to comprehensively investigate the effects of acupuncture on the daily living abilities, upper and lower limb motor function, and related functional indices of post-stroke patients with spastic paralysis.

METHODS

We conducted a computer search to collect data from PubMed, PEDro, Clinical SportDiscus, and Scopus. The inclusion criteria followed the Population-Intervention-Comparison-Outcome (PICO) principle. Literature screening, data extraction, and quality assessment of the research articles were performed by two independent investigators. Standard mean difference and 95% confidence intervals of the data were analyzed using either a random-effects model or a fixed-effects model.

RESULTS

Acupuncture therapy appeared to be effective in mitigating the limb pain of post-stroke patients with spastic paralysis (RR = -0.04, 95% CI: -0.26, 0.17), ameliorating their daily life ability (RR = 4.66, 95% CI: -0.74, 10.05), and improving their hand function (RR = 0.65, 95% CI: 0.40, 0.90) and lower limb function (RR = 0.35, 95% CI: 0.09, 0.62).

CONCLUSION

Acupuncture therapy provides more pronounced improvement in the daily life ability and limb motor function of post-stroke patients with spastic paralysis than conventional treatment regimens. Thus, acupuncture therapy can be a viable treatment option for the management of spastic paralysis following stroke.

Investigation of Characteristic Motion Patterns of the Knee Joint During a Weightbearing Flexion

This study aimed to develop and validate a novel flexion axis concept by calculating the points on femoral condyles that could maintain constant heights during knee flexion. Twenty-two knees of 22 healthy subjects were investigated when performing a weightbearing single leg lunge. The knee positions were captured using a validated dual fluoroscopic image system. The points on sagittal planes of the femoral condyles that had minimal changes in heights from the tibial plane along the flexion path were calculated. It was found that the points do formulate a medial-lateral flexion axis that was defined as the iso-height axis (IHA). The six degrees of freedom (6DOF) kinematics data calculated using the IHA were compared with those calculated using the conventional transepicondylar axis and geometrical center axis. The IHA measured minimal changes in proximal-distal translations and varus-valgus rotations along the flexion path, indicating that the IHA may have interesting clinical implications. Therefore, identifying the IHA could provide an alternative physiological reference for improvement of contemporary knee surgeries, such as ligament reconstruction and knee replacement surgeries that are aimed to reproduce normal knee kinematics and medial/lateral soft tissue tensions during knee flexion.

Bicruciate-retaining total knee arthroplasty procedure reduced tensile force in the middle and posterior components of lateral collateral ligament during deep knee flexion activities with no effect on tensile force of the medial collateral ligament

PURPOSE

To analyse the effects of bicruciate-retaining total knee arthroplasty (BCR-TKA) on the tensile force of the collateral ligaments during two deep knee flexion activities, cross-leg sitting and squatting.

METHODS

Thirteen patients (15 knees) treated using bicruciate-retaining total knee arthroplasty (BCR-TKA) for knee joint osteoarthritis were analysed. Knee joint kinematics during cross-leg sitting (open-chain flexion) and squatting (closed-chain flexion) were evaluated through fluoroscopy. The tensile force was calculated in vivo based on the change in the distance between the femoral and tibial attachment areas for the anterior, middle, and posterior components of the superficial (sMCL) and deep (dMCL) medial collateral ligament and the lateral collateral ligament (LCL). Differences in the calculated tensile forces of the collateral ligaments were evaluated using repeated measures of analysis of variance, with post hoc pairwise comparison (Bonferroni test). Statistical significance was set at P ≤ 0.05.

RESULTS

The correction of the coronal alignment was related to the surgical technique, not to the implant design. No significant change in the tensile force in all three components of the sMCL from pre- to post-TKA (n.s.) was observed. For dMCL, a pre- to post-TKA change in the tensile force was observed only for the anterior dMCL component (p = 0.03). No change was observed in the tensile force of the anterior LCL with increasing flexion, with no difference in pre- to post-TKA and between activities (n.s.). In contrast, tensile force in the middle LCL slightly decreased with increasing flexion during squatting, pre- and post-TKA. After surgery, lower forces were generated at 40° of flexion (p = 0.04). Tensile force in the posterior LCL was higher in extension than flexion, which remained high in the extension post-TKA. However, after surgery, lower tensile forces were generated at 10° (p = 0.04) and 40° (p = 0.04) of flexion.

CONCLUSIONS

The in vivo change in tensile forces of the collateral ligaments of the knee before and after BCR-TKA can inform the development of appropriate ligament balancing strategies to facilitate recovery of deep knee flexion activities after TKA, as well as for continued improvement of BCR-TKA designs.

LEVEL OF EVIDENCE

III.

Improved Knee Function with Customized vs. Off-the-Shelf TKA Implants-Results of a Single-Surgeon, Single-Center, Single-Blinded Study

BACKGROUND

Recent studies have been able to show certain benefits of Customized, Individually Made (CIM) compared to Off-the-Shelf (OTS) total knee arthroplasties (TKAs), but evidence is still lacking regarding the benefits of these implant systems. This study aimed to find differences in scores and functional outcome by comparing CIM and OTS implants, using Patient-Reported Outcome Measures (PROMs) and functional tests for activities of daily living in a single-surgeon setup.

METHODS

A total of 48 patients (16 CIM vs. 32 OTS) were consecutively enrolled and blindly examined. Functional testing was performed using four timed functional tests (TUG, WALK, TUDS, and BBS) and the VAS for pain. The Aggregated Locomotor Function (ALF) score was then calculated based on the addition of the average times of the three functional tests.

RESULTS

The CIM group showed significantly faster times in all functional tests and significantly better ALF scores. There were remarkable differences in the assessment of maximum pain sensation between the two groups, with superiority in the CIM group. The PROMs analysis revealed a higher proportion of excellent and good ratings for the items objective and function (KSS) in the CIM group.

CONCLUSION

The study showed that time-limited activities of daily living (ADLs) can be completed significantly faster with a CIM prosthesis and that a significantly higher percentage in this group reports freedom from pain during certain loads. Partial aspects of the PROM scores are also better in this group; however, this superiority could not be shown with regard to most PROM scores collected in this study.

Comparison of clinical outcomes among total knee arthroplasties using posterior-stabilized, cruciate-retaining, bi-cruciate substituting, bi-cruciate retaining designs: a systematic review and network meta-analysis

BACKGROUND

Despite the advent of innovative knee prosthesis design, a consistent first-option knee implant design in total knee arthroplasty (TKA) remained unsettled. This study aimed to compare the clinical effects among posterior-stabilized (PS), cruciate-retaining (CR), bi-cruciate substituting (BCS), and bi-cruciate retaining designs for primary TKA.

METHODS

Electronic databases were systematically searched to identify eligible randomized controlled trials (RCTs) and cohort studies from inception up to July 30, 2021. The primary outcomes were the range of knee motion (ROM), and the secondary outcomes were the patient-reported outcome measures (PROMs) and complication and revision rates. Confidence in evidence was assessed using Confidence in Network Meta-Analysis. The Bayesian network meta-analysis was performed for synthesis.

RESULTS

A total of 15 RCTs and 18 cohort studies involving 3520 knees were included. The heterogeneity and inconsistency were acceptable. There was a significant difference in ROM at the early follow-up when PS was compared with CR (mean difference [MD] = 3.17, 95% confidence interval [CI] 0.07, 7.18) and BCS was compared with CR (MD = 9.69, 95% CI 2.18, 17.51). But at the long-term follow-up, there was no significant difference in ROM in any one knee implant compared with the others. No significant increase was found in the PROMs and complication and revision rates at the final follow-up time.

CONCLUSIONS

At early follow-up after TKA, PS and BCS knee implants significantly outperform the CR knee implant in ROM. But in the long run, the available evidence suggests different knee prostheses could make no difference in clinical outcomes after TKA with extended follow-up.

Better flexion and early recovery with medial-stabilized vs single-radius total knee arthroplasty with kinematic alignment: Two-year clinical results

BACKGROUND

There are few studies comparing outcomes in patients with posterior cruciate ligament-sacrificing single-radius (SR) versus medial-stabilized (MS) knee devices. Both types of implants are designed to maximize deep-flexion and to maintain stability throughout the knee flexion arc. The aim of this study was to determine whether two-year outcomes differ between these two implant groups.

METHODS

Two-hundred and ten patients took part in this retrospective cohort single center study. The SR patients (n = 109) were enrolled in one randomized trial, and the MS knees (n = 101) in another. Patient consent and Investigative Review Board approval was obtained. Radiographs and clinical outcomes were gathered preoperatively and at six weeks, six months, one year and two years.

RESULTS

There were no statistically significant differences between treatment groups in terms of preoperative demographic characteristics. The MS group had significantly better knee flexion starting at six months postoperative through two years postoperatively (p < 0.05 - p< 0.001). The Knee Society Pain/Motion score was better in the MS group at one year (95.41 vs 90.86, p < 0.002). The Knee Society Pain score was also better in the MS group starting at six weeks through one year (six weeks: 35.3 vs 30, p = 0.007; one year: 46.4 vs 42.4, p = 0.005, respectively).

CONCLUSION

The MS group had better clinical outcomes than the SR group, with significantly greater knee flexion from six months through two years, better Knee Society Pain scores at six weeks through one year, and higher Knee Society Pain/Motion scores at six weeks and one year postoperatively.

LEVEL OF EVIDENCE

I.

Learning curve and short-term clinical outcomes of a new seven-axis robot-assisted total knee arthroplasty system: a propensity score-matched retrospective cohort study

OBJECTIVE

The purpose of the present study was to determine the learning curve for a novel seven-axis robot-assisted (RA) total knee arthroplasty (TKA) system and to explore whether it could provide superior short-term clinical and radiological outcomes compared with conventional surgery.

METHODS

In the present retrospective study, 90 patients who underwent RA-TKA were included in robot-assisted system (RAS) group and 90 patients who underwent conventional TKA were included in the conventional group. The duration of surgery and robot-related complications were recorded to evaluate the learning curve through cumulative sum and risk-adjusted cumulative sum methods. The demographic data, preoperative clinical data, preoperative imaging data, duration of surgery, alignment of the prosthesis, lower limb force line alignment, Knee Society score, 10-cm visual analog scale pain score and range of motion were compared between the RAS and conventional groups. In addition, the proficiency group was compared with the conventional group using propensity score matching.

RESULTS

RA-TKA was associated with a learning curve of 20 cases for the duration of surgery. There was no significant difference in indicators representing the accuracy of the prosthetic installation between the learning and proficiency phases in RA-TKA group patients. A total of 49 patients in the proficiency group were matched with 49 patients from the conventional group. The number of postoperative hip-knee-ankle (HKA) angle, component femoral coronal angle (CFCA), component tibial coronal angle (CTCA), and sagittal tibial component angle (STCA) outliers in the proficiency phase was lower than that in the conventional group, while deviations of the HKA angle, CFCA, CTCA, and STCA in the proficiency phase were significantly lower than those in the conventional group (P < 0.05).

CONCLUSION

In summary, from the learning curve data, 20 cases are required for a surgeon using a novel seven-axis RA-TKA system to enter the proficiency phase. In the proficiency group, compared with the conventional group using propensity score matching, the RAS was found to be superior to the conventional group in prosthesis and lower limb alignment.

Finite element analysis of a healthy knee joint at deep squatting for the study of tibiofemoral and patellofemoral contact

Background

In non-western countries, deep squatting is a daily activity, and prolonged deep squatting is common among occupational squatters. Household tasks, taking a bath, socializing, using toilets, and performing religious acts are among the activities frequently carried out while squatting by the Asian population. High knee loading is responsible for a knee injury and osteoarthritis. Finite element analysis is an effective tool to determine stresses on the knee joint.

Methods

Magnetic Resonance Imaging (MRI) and Computed Tomographic (CT) images were acquired of one adult without knee injuries. The CT images were acquired at the fully extended knee and one more set of images was acquired with the knee at a deeply flexed knee position. The MRI was acquired with the fully extended knee. 3-Dimensional models of bones were created using CT and soft tissue using MRI with the help of 3D Slicer software. Kinematics and finite element analysis of the knee was performed for standing and deep squatting posture using Ansys Workbench 2022.

Results

High peak stresses were observed at deep squatting compared to standing along with the reduction in the contact area. Peak von Mises stresses on femoral cartilage, tibial cartilage, patellar cartilage, and meniscus were increased from 3.3 MPa to 19.9 MPa, 2.9 MPa to 12.4 MPa, 1.5 MPa to 16.7 MPa and 15.8 MPa to 32.8 MPa respectively during deep squatting. Posterior translation of 7.01 mm, and 12.58 mm was observed for medial and lateral femoral condyle respectively from full extension to 153° knee flexion.

Conclusions

Increased stresses in the knee joint at deep squat posture may cause cartilage damage. A sustained deep squat posture should be avoided for healthy knee joints. More posterior translations of the medial femoral condyle at higher knee flexion angle warrant further investigation.

Validation of a machine learning technique for segmentation and pose estimation in single plane fluoroscopy

Kinematics of total knee replacements (TKR) play an important role in assessing the success of a procedure and would be a valuable addition to clinical practice; however, measuring TKR kinematics is time consuming and labour intensive. Recently, an automatic single-plane fluoroscopic method utilizing machine learning has been developed to facilitate a quick and simple process for measuring TKR kinematics. This study aimed to validate the new automatic single-plane technique using biplanar radiostereometric analysis (RSA) as the gold standard. Twenty-four knees were imaged at various angles of flexion in a dedicated RSA lab and 113 image pairs were obtained. Only the lateral RSA images were used for the automatic single-plane technique to simulate single-plane fluoroscopy. Two networks helped automate the kinematics measurement process, one segmented implant components and the other generated an initial pose estimate for the optimization algorithm. Kinematics obtained via the automatic single plane and manual biplane techniques were compared using root-mean-square error and Bland-Altman plots. Two observers measured the kinematics using the automated technique and results were compared with assess reproducibility. Root-mean-square errors were 0.8 mm for anterior-posterior translation, 0.5 mm for superior-inferior translation, 2.6 mm for medial-lateral translation, 1.0° for flexion-extension, 1.2° for abduction-adduction, and 1.7° for internal-external rotation. Reproducibility, reported as root-mean-square errors between operator measurements, was submillimeter for in-plane translations and below 2° for all rotations. Clinical Significance: The advantages of the automated single plane technique should aid in the kinematic measurement process and help researchers and clinicians perform TKR kinematic analyses.

Mid-Flexion, Anteroposterior Stability of Total Knee Replacement Implanted with Kinematic Alignment: A Randomized, Quantitative Radiographic Laxity Study with Posterior-Stabilized and Medial-Stabilized Implants

UPDATE

This article was updated on January 4, 2023, because of a previous error, which was discovered after the preliminary version of the article was posted online. On page 16, in Figure 5, the x-axis that had read "P<0.0086" now reads "KSS Pain (p=0.02)," and the value for the MS group that had read "48.9" now reads "48.8."This article was updated on January 6, 2022, because of a previous error. On page 13, in the section entitled "Results," the sentence that had read "However, when only the subset of female subjects was considered, the MS group demonstrated significantly less anteroposterior laxity in 90° of flexion than the MS group (2.3 versus 5.4 mm; p = 0.008)." now reads "However, when only the subset of female subjects was considered, the MS group demonstrated significantly less anteroposterior laxity in 90° of flexion than the PS group (2.3 versus 5.4 mm; p = 0.008)."

BACKGROUND

Stability in mid-flexion is important for satisfactory clinical outcomes following total knee arthroplasty (TKA). The purpose of the present study was to compare the anteroposterior stability of knees that had been treated with a posterior-stabilized (PS) device or a medial-stabilized (MS) device. We hypothesized that mid-flexion laxity would be greater in the PS group and that clinical outcome scores would be better for the group with lower laxity.

METHODS

Sixty-three patients who had been randomly selected from a larger randomized, prospective, blinded clinical trial underwent primary TKA with either a PS implant (n = 30) or an MS implant (n = 33). Range of motion, the Knee Society Score (KSS), and the Forgotten Joint Score (FJS) were collected, and anteroposterior laxity with the knee in 45° and 90° of flexion was evaluated with stress radiographs.

RESULTS

In 45° of flexion, the MS group demonstrated significantly less total anteroposterior displacement than the PS group (mean, 3.6 versus 16.5 mm; p ≤ 0.0001). In 90° of flexion, the total anteroposterior displacement was not significantly different for the 2 groups when both male and female patients were included (mean, 3.9 versus 5.9; p = 0.07). However, when only the subset of female subjects was considered, the MS group demonstrated significantly less anteroposterior laxity in 90° of flexion than the PS group (2.3 versus 5.4 mm; p = 0.008). The groups did not differ significantly in terms of preoperative age, body mass index, sex distribution, FJS, KSS, or range of motion, and they also did not differ in terms of postoperative FJS or range of motion. However, all 33 patients in the MS group returned to sports as indicated in question 12 of the FJS, compared with 19 subjects in the PS group (p = 0.0001). The postoperative KSS Pain, Pain/Motion, and Function scores were all significantly higher in the MS group than the PS; specifically, the mean KSS Pain score was 48.8 in the MS group, compared with 44.8 in the PS group (p = 0.02); the mean KSS Pain/Motion score was 98.4 in the MS group, compared with 89.5 in the PS group (p < 0.0001); and the mean KSS Function score was 95.5 in the MS group, compared with 85.7 in the PS group (p = 0.003).

CONCLUSIONS

Mid-flexion laxity was greater in patients with PS implants than in those with MS implants, and laxity in 90° was greater in the subset of female patients in the PS group. The decreased laxity observed in the MS group correlated with higher KSS Pain, Pain/Motion, and Function scores as well as with a higher rate of return to sports activities.

LEVEL OF EVIDENCE

Therapeutic Level I . See Instructions for Authors for a complete description of levels of evidence.

Comparison of the in-vivo kinematics of three different knee prosthesis designs during a step-up movement

BACKGROUND

There is no consensus on the importance of the kinematics of the prosthetic joint for the clinical outcome after total knee arthroplasty. A 3-armed randomized controlled trial was done to determine and compare the in vivo kinematics of a posterior cruciate-retaining and two posterior cruciate-sacrificing (Anterior-Stabilized and Posterior-Stabilized) prosthetic designs from the same total knee arthroplasty system. Since the anterior-stabilized and posterior-stabilized designs are posterior cruciate ligament-sacrificing designs, we hypothesized they would have similar contact-point kinematics. Further, we hypothesized that the cruciate-retaining design would have contact-point kinematics different from the anterior-stabilized and the posterior-stabilized designs, but comparable to a native knee.

METHODS

Thirty-nine patients with a well-functioning total knee arthroplasty one year postoperatively underwent kinematic analysis of a weight-bearing step-up movement under fluoroscopic recording. Model-based radiostereometric analysis was used to determine anteroposterior contact-point translations and rotations through the movement path to assess knee kinematics.

FINDINGS

The cruciate-retaining and anterior-stabilized groups' medial and lateral contact-points displayed similar paradoxical posterior translations during step-up in the magnitude of 7 and 2 mm, respectively. In contrast, the posterior-stabilized group's contact-points translated anteriorly by 4 and 10 mm throughout the movement and were significantly more posterior than the cruciate-retaining and the anterior-stabilized groups from >100° to 40° of flexion. The femur rotated internally with all designs.

INTERPRETATION

The cruciate-retaining and anterior-stabilized designs displayed similar contact-point translation patterns during a step-up movement. Only the posterior-stabilized design showed a pattern comparable to native knees. Conversion from a cruciate-retaining to an anterior-stabilized design because of posterior cruciate ligament insufficiency will not change knee kinematics.

Prospective sequential comparison of femoral roll-back between cruciate-retaining and posterior-stabilized total knee arthroplasty using an intra-operative sensor

BACKGROUND

Implant design and surgical techniques affect postoperative knee kinematics in total knee arthroplasty (TKA). This study aimed to compare femoral roll-back between cruciate-retaining (CR) and posterior-stabilized (PS) TKA in the same knee by objectively quantifying the contact point kinematics of the tibiofemoral joint using a sensor.

METHODS

In the present prospective study, we used an intraoperative sensor to compare medial and lateral roll-back during 0-120° knee flexion in 33 knees that underwent CR and PS TKA. We also examined the relationship between mediolateral balance and the lateral-to-medial roll-back ratio. We defined the contact percentage position as the vertical length to the contact point divided by the anteroposterior length of the tibial plate.

RESULTS

The roll-back percentage following PS TKA (19.8 ± 5.1%) was significantly higher than that after CR TKA in both the medial (19.8 ± 5.1% versus 7.1 ± 2.5%, P < 0.001) and lateral (26.8% ± 3.8% versus 18.7 ± 3.8%, P < 0.001) compartments. The medial contact pressure at 90° was significantly correlated with the increased lateral-to-medial roll-back ratio in both CR and PS TKA (both P < 0.001).

CONCLUSION

PS TKA resulted in a higher percentage of femoral roll-back in the medial and lateral compartments than CR TKA. CR TKA caused a higher lateral-to-medial roll-back ratio compared to PS TKA. To reproduce medial pivot knee motion similar to that of a normal knee, the medial soft tissue needed to be balanced more tightly than the lateral soft tissue during TKA. These findings provide some clinical evidence of TKA design selection and proper mediolateral balancing for successful TKA.

Endurance Behavior of Cemented Tibial Tray Fixation Under Anterior Shear and Internal-External Torsional Shear Testing: A New Methodological Approach

BACKGROUND

Early total knee arthroplasty failures continue to surface in the literature. Cementation technique and implant design are two of the most important scenarios that can affect implant survivorship. Our objectives were to develop a more suitable preclinical test to evaluate the endurance of the implant-cement-bone interface under anterior shear and internal-external (I/E) torsional shear testing condition in a biomechanical sawbones.

METHODS

Implants tested included the AS VEGA System PS and the AS Columbus CR/PS (Aesculap AG, Germany), with zirconium nitride (ZrN) coating. Tibial implants were evaluated under anterior shear and I/E torsional shear conditions with 6 samples in 4 test groups. For the evaluation of the I/E torsional shear endurance behavior, a test setup was created allowing for clinically relevant I/E rotation with simultaneous high axial/tibio-femoral load. The test was performed with an I/E displacement of ±17.2°, for 1 million cycles with an axial preload of 3,000 N.

RESULTS

After the anterior shear test an implant-cement-bone fixation strength for the AS VEGA System tibial tray of 2,674 ± 754 N and for the AS Columbus CR/PS tibial tray of 2,177 ± 429 N was determined (P = .191). After I/E rotational shear testing an implant-cement-bone fixation strength for the AS VEGA System PS tray of 2,561 ± 519 N and for the AS Columbus CR/PS tray of 2,824 ± 515 N was resulted (P = .39).

CONCLUSION

Both methods had varying degrees of failure modes from debonding to failure of the sawbones foam. These two intense biomechanical loading tests are more strenuous and more representative of clinical activity.

Knee kinematics are variously influenced by different correction angles in high tibial osteotomy (HTO)

PURPOSE

Literature reveals good to excellent data concerning patient satisfaction, as well as long-term outcomes after high tibial osteotomy (HTO). These results might be influenced by changes of knee kinematics through the procedure. However, exact influence of HTO on tibiofemoral kinematics remains unknown so far.

METHODS

We conducted this study on 10 knees of Thiel embalmed whole cadavers. Knee kinematics were assessed by a navigation device before HTO, after medial open-wedge HTO of 5°, respectively after medial open-wedge HTO of 10°.

RESULTS

Results revealed a significant femoral rollback/tibial internal rotation at increasing knee flexion from 80° after medial open-wedge HTO of 5° and 10°. Lesser femoral rollback/tibial internal rotation was seen after 5° HTO compared to 10° HTO until knee flexion of 70°.

CONCLUSION

Results reveal a significant change of tibiofemoral kinematics only after knee flexion of 80° and more, independently from the degree of tibial osteotomy. Adjacent structures, especially the ACL, seem thus more strained by sagittal slope changes rather than changes in coronal leg axis. HTO leads to changes in knee kinematics at flexion degrees of 80 and more. To what extent this influences adjacent structures like the ACL or meniscus should be further investigated.

Sensor Use in Cruciate-Retaining Total Knee Arthroplasty Compared with Posterior-Stabilized Total Knee Arthroplasty: Load Balancing and Posterior Femoral Rollback

The purpose was to investigate the proportion of severe load imbalance after appropriate conventional gap balancing and analyze the intraoperative kinematics after load balancing in cruciate-retaining (CR) and posterior-stabilized (PS) total knee arthroplasties (TKAs). In total, 45 sensor-assisted CR and 45 PS TKAs using NexGen prosthesis were prospectively evaluated. After appropriate conventional gap balancing, the loads at 10, 45, and 90 degrees of knee flexion were evaluated with a wireless load sensor placed in trial implants. The proportion of severe load imbalance (medial load-lateral load >75 lbs) was investigated. After load balancing, location of the femorotibial contact point was investigated at each flexion angle to analyze femorotibial kinematics. The proportion of the severe load imbalance was significantly higher in CR TKAs at the 10 degrees knee flexion (37.8 vs. 15.6%, p = 0.031). This proportion was higher in CR TKAs than in PS TKAs at the 45 and 90 degrees knee flexion angles, but without statistical significance (31.1 vs. 15.6%, p = 0.134 and 33.3 vs. 15.6%, p = 0.085, respectively). After load balancing, consistent posterior femoral rollback occurred in medial and lateral compartments during 90 degrees flexion in CR TKAs (p < 0.001), but not in PS TKAs. Medial pivot kinematics was not observed in both TKA designs. The sensor was more beneficial in CR TKAs for achieving appropriate load balancing and consistent posterior femoral rollback compared with PS TKAs. Further studies are required to identify target load distribution to restore ideal knee kinematics after TKA. This study shows level of evidence II.

In vivo kinematic comparison of medial pivot total knee arthroplasty in weight-bearing and non-weight-bearing deep knee bending

BACKGROUND

This study aimed to determine the kinematics of medial pivot total knee arthroplasty by comparing weight-bearing and non-weight-bearing deep knee bending and to evaluate the effect of the weight-bearing state on the kinematics.

METHODS

The kinematics of 19 knees were investigated under fluoroscopy during squatting (weight-bearing) and active-assisted knee bending (non-weight-bearing) using two- to three-dimensional registration technique. Accordingly, range of motion, anteroposterior translation for the medial and lateral low contact points, axial rotation of the femoral component relative to the tibial component and kinematic pathway were evaluated.

FINDINGS

There was no difference in range of motion between the two states. The medial anteroposterior translation showed no significant movement with no anterior translation in both the weight-bearing and non-weight-bearing from 0° to 90° of flexion. Regarding the lateral anteroposterior translation, a posterior translation was observed during weight-bearing, whereas a slight anterior translation from 0° to 30° of flexion and subsequent posterior translation were found in the non-weight-bearing. Femoral external rotation was observed in the weight-bearing, whereas femoral internal rotation was seen from 0° to 30° of flexion and subsequent femoral external rotation was observed in the non-weight-bearing. The kinematic pathway showed medial pivot motion and subsequent bicondylar rollback in the weight-bearing, whereas only medial pivot motion was observed in the non-weight-bearing.

INTERPRETATION

The medial anteroposterior translation of the femur during deep knee bending showed no anterior motion in the two states. The lateral anteroposterior translation and femoral rotation were different in the mid-flexion range between the two states.

Outcomes are Better With a Medial-Stabilized vs a Posterior-Stabilized Total Knee Implanted With Kinematic Alignment

BACKGROUND

There is no consensus whether a posterior-stabilized (PS) total knee device is superior to a more congruent, cruciate-substituting, medial-stabilized device (MS). This study compared the clinical outcomes of these devices. The primary hypothesis was that the clinical outcomes would be better in the MS group implanted with kinematic alignment.

METHODS

This prospective, randomized, single-center Level 1 study compared the outcomes of 99 patients who received a PS device and 101 patients who received an MS device implanted with kinematic alignment. Institutional Review Board approval and informed consent were obtained. Clinical and radiographic assessments were performed preoperatively, 6 weeks, 6 months, and annually.

RESULTS

All subjects reached the minimum follow-up of 2 years. There were no statistically significant differences in demographic characteristics, preoperative scores, or alignment (preoperative or postoperative). Tourniquet time was 7.24% longer for the PS group (40.28 min vs 37.56 min, P < .0086). There were significant differences between groups for the 1-year and 2-year Knee Society scores, Forgotten Joint Score, and ROM; in every case favoring the MS group. The FJS was 68.3 in the MS group at 2 years and 58.3 in the PS group (P = .02). The maximum flexion at 2 years was 132° in the MS group and 124° in the PS group (P < .0001).

CONCLUSION

The clinical outcomes of the MS group at 1 and 2 years were better. At the minimum 2-year follow-up, the results demonstrate the superiority of the medial-stabilized device in terms of multiple clinical outcomes.

LEVEL OF EVIDENCE

I.

Impact of femoro-tibial size combinations and TKA design on kinematics

INTRODUCTION

The variability in patients' femoral and tibial anatomy requires to use different tibia component sizes with the same femoral component size. These size combinations are allowed by manufacturers, but the clinical impact remains unclear. Therefore, the goals of our study were to investigate whether combining different sizes has an impact on the kinematics for two well-established knee systems and to compare these systems' kinematics to the native kinematics.

MATERIALS AND METHODS

Six fresh frozen knee specimens were tested in a force controlled knee rig before and after implantation of a cruciate retaining (CR) and a posterior-stabilized (PS) implant. Femoro-tibial kinematics were recorded using a ultrasonic-based motion analysis system while performing a loaded squat from 30° to 130°. In each knee, the original best fit inlay was then replaced by different inlays simulating a smaller or bigger tibia component. The kinematics obtained with the simulated sizes were compared to the original inlay kinematics using descriptive statistics.

RESULTS

For all size combinations, the difference to the original kinematics reached an average of 1.3 ± 3.3 mm in translation and - 0.1 ± 1.2° in rotation with the CR implant. With the PS implant, the average differences reached 0.4 ± 2.7 mm and  - 0.2 ± 0.8°. Among all knees, no size combination consistently resulted in significantly different kinematics. Each knee showed a singular kinematic pattern. For both knee systems, the rotation was smaller than in the native knee, but the direction of the rotation was preserved. The PS showed more rollback and the CR less rollback than the native knee.

CONCLUSION

TKA systems designed with a constant tibio-femoral congruency among size combinations should enable to combine different sizes without having substantial impact on the kinematics. The rotational pattern was preserved by both TKA systems, while the rollback could only be maintained by the PS design.

Patient and Implant Performance of Satisfied and Dissatisfied Total Knee Arthroplasty Patients

BACKGROUND

Implant migration and altered kinematics have been thought to impact patient-reported outcome measures (PROMs) and postoperative patient satisfaction. In this study comparing satisfied and dissatisfied total knee arthroplasty (TKA) patients, we hypothesized that dissatisfied patients will have greater continuous implant migration and that there will be differences in joint kinematics, objective functional measurements, and PROMs between satisfied and dissatisfied patients.

METHODS

The Knee Society Score Satisfaction Subsection questions regarding satisfaction with function were used at least 6 months postoperation to split 50 patients into satisfied and dissatisfied groups. Patients underwent radiostereometric analysis to evaluate migration and kinematics. A wearable sensor system obtained objective measurements of patient function during timed up and go tests. PROMs were recorded preoperation and postoperation.

RESULTS

No statistically significant differences were found in migration between satisfied and dissatisfied groups. Statistical kinematic differences existed in lateral anteroposterior contact location at 20° and 40° of flexion at 1 year, where the dissatisfied group had more anteriorly located lateral contact. No statistically significant differences were present in objective functional measurements. Satisfied and dissatisfied groups had differing PROMs at 4 timepoints or greater for each questionnaire.

CONCLUSIONS

No differences were found in tibial component migration or objectively measured function between satisfied and dissatisfied patients. Functionally dissatisfied patients had more anteriorly positioned contact on the lateral condyle in early flexion and reported more pain and unmet expectations. These findings suggest that improving the functional satisfaction of TKA requires restoration of kinematics in early flexion and management of patient's pain and expectations.

In Vivo three-dimensional kinematics of normal knees during sitting sideways on the floor

Background

The normal knee kinematics during asymmetrical kneeling such as the sitting sideways remains unknown. This study aimed to clarify in vivo kinematics during sitting sideways of normal knees.

Methods

Twelve knees from six volunteers were examined. Under fluoroscopy, each volunteer performed a sitting sideways. A two-dimensional/three-dimensional registration technique was used. The rotation angle, varus-valgus angle, anteroposterior translation of the medial and lateral sides of the femur relative to the tibia, and kinematic pathway in each flexion angle was evaluated.

Results

Bilateral knees during sitting sideways showed a femoral external rotation relative to the tibia with flexion (ipsilateral: 13.7 ± 3.5°, contralateral: 5.8 ± 6.8°). Whereas the ipsilateral knees showed valgus movement of 4.6 ± 2.5° from 130° to 150° of flexion, and the contralateral knees showed varus movement of -3.1 ± 4.4° from 110° to 150° of flexion. The medial side of the contralateral knees was more posteriorly located than that of the ipsilateral knees beyond 110° of flexion. The lateral side of the contralateral knees was more anteriorly located than that of the ipsilateral knees from 120° to 150° of flexion. In the ipsilateral knees, a medial pivot pattern followed by a bicondylar rollback was observed. In the contralateral knees, no significant movement followed by a bicondylar rollback was observed.

Conclusion

Even though the asymmetrical kneeling such as sitting sideways, the knees did not display asymmetrical movement.

The higher patient-reported outcome measure group had smaller external rotation of the femur in bicruciate-stabilized total knee arthroplasty

PURPOSE

The hypothesis of this study was that the kinematics of patients with higher patient-reported outcome measures (PROMs) differ from those of patients with lower PROMs after bicruciate-stabilized total knee arthroplasty (BCS-TKA).

METHODS

A total of 32 patients with severe knee osteoarthritis were examined 11.2 ± 3.2 months after BCS-TKA. The patients performed squats under single fluoroscopic surveillance in the sagittal plane. To estimate the spatial position and orientation of the femoral and tibial components, a 2D-to-3D registration technique was used. This technique uses a contour-based registration algorithm, single-view fluoroscopic images and 3D computer-aided design models. Knee range of motion, varus-valgus alignment, axial rotation of the femur relative to the tibial component, anteroposterior translation of the medial and lateral femorotibial contact points, kinematic paths, and anterior and posterior post-cam engagement were measured. The patients were divided into two groups using hierarchical cluster analysis based on the 1-year postoperative Knee Injury and Osteoarthritis Outcome Score and 2011 Knee Society Score.

RESULTS

The femoral component had significantly more external rotation in the low-score group than in the high-score group (5.1 ± 1.8° vs. 2.2 ± 2.7°, p = 0.02). The high-score group had a medial pivot pattern from 0 to 20° of flexion, without significant movement from 20 to 70°, and final bicondylar rollback beyond 70°. The low-score group had a medial pivot from 0 to 70° of flexion and bicondylar rollback beyond 70°. There were no significant between-group differences in the varus-valgus angle or post-cam engagement.

CONCLUSION

The higher PROM group had smaller external rotation of the femur after BCS-TKA.

LEVEL OF EVIDENCE

Level III.

Obtaining anatomic motion and laxity characteristics in a total knee design

BACKGROUND

Since the introduction of the first total knee designs, a frequent design goal has been to reproduce normal knee motion. However, studies of many currently used total knee designs, have shown that this goal has not been achieved. We proposed that Guided Motion total knee designs, could achieve more anatomic motion than present standard designs.

METHODS

Several Guided Motion knees for application without cruciate ligaments were designed using a computer method where the bearing surfaces were generated by the motion required. A knee testing machine was constructed where physiological forces including compressive, shear and torque were applied during knee flexion. The neutral path of motion and the laxity about the neutral path were measured. This evaluation method was a modification of the ASTM standard Constraint Test.

RESULTS

The motions of the Guided Motion knees and a standard PS knee were compared with the anatomic motion of knee specimens determined in an earlier study The Guided Motion knees showed motion patterns which were closer to anatomic than the PS knee.

CONCLUSIONS

The results provided justification for carrying out further evaluations of functional conditions, using either knee simulators or computer modelling. If anatomic motions could be reproduced in vivo, it is possible that clinical outcomes could be improved.

A Comparison of Clinical Outcomes and Implant Preference of Patients with Bilateral TKA: One Knee with a Patient-Specific and One Knee with an Off-the-Shelf Implant

BACKGROUND

The purpose of this retrospective study was to compare clinical outcome results, perceived function, and overall preference among patients who had undergone staged bilateral total knee arthroplasty (TKA) with a cruciate-retaining, customized implant (customized TKA, or C-TKA) in 1 knee and an off-the-shelf (OTS) implant in the contralateral knee.

METHODS

Forty-seven patients (94 knees) from a single study center who underwent C-TKA in 1 knee and had previously undergone TKA with an OTS implant in the contralateral knee were included in this study. As the primary outcome measures, the Knee injury and Osteoarthritis Outcome Score, Joint Replacement (KOOS, JR) and the Forgotten Joint Score (FJS) were self-administered by the study subjects at a single follow-up time point. Additionally, a follow-up questionnaire to compare patients' perceived joint stability, knee mobility, perceived feeling of the replaced joint, pain levels, and overall preference between their knees was administered.

RESULTS

The average follow-up was 2.3 years (range, 0.7 to 3.8 years) for C-TKA and 6.7 years (range, 1.6 to 11.1 years) for the OTS TKA. Significantly higher KOOS, JR (82 versus 77; p = 0.03) and FJS (68 versus 58; p = 0.04) results were found with C-TKA. The evaluation of the follow-up questionnaire showed that more patients reported having "a little" or "a lot" less pain (49% versus 15%), better perceived mobility (45% versus 12%) and stability (36% versus 13%), and a more "normal" feeling of their knee (60% versus 10%) with the C-TKA implant compared with their OTS counterpart. When patients were asked to directly compare their knees, we found that 72.3% of the patients preferred the knee that received C-TKA over the contralateral OTS knee replacement, with 21.3% seeing no difference and 6.4% preferring the OTS knee replacement.

CONCLUSIONS

We believe that this is the first study to examine patient-reported outcomes of customized and OTS TKA implant designs in the same patient. We conclude that patients in this study cohort who underwent staged bilateral TKA with a C-TKA implant in 1 knee and an OTS prosthesis in the other knee reported better for their patient-specific knee replacement, with higher FJS and KOOS, JR values, and overall, preferred the C-TKA knee more often compared with the OTS knee replacement.

LEVEL OF EVIDENCE

Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Does Risk Mitigation Reduce 90-Day Complications in Patients Undergoing Total Knee Arthroplasty? A Cohort Study

Background

With ever-increasing demand for total knee arthroplasty (TKA), most healthcare systems around the world are concerned about its socioeconomic burden. Most centers have universally adopted well-defined clinical care pathways to minimize adverse outcomes, maximize volume, and limit costs. However, there are no prospective comparative trials reporting benefits of these risk mitigation (RM) strategies.

Methods

This is a prospective cohort study comparing post-TKA 90-day complications between patients undergoing RM before surgery and those following a standard protocol (SP). In the RM group, we used a 20-point checklist to screen for modifiable risk factors and evaluate the need for optimizing non-modifiable comorbidities. Only when optimization goals were achieved, patients were offered TKA.

Results

TKA was performed in 811 patients in the SP group and in 829 in the RM group, 40% of which were simultaneous bilateral TKA. In both groups, hypertension was the most prevalent comorbidity (48%), followed by diabetes (20%). A total of 43 (5.3%) procedure-related complications were seen over the 90-day postoperative period in the SP group, which was significantly greater than 26 (3.1%) seen in the RM group (p = 0.039). The commonest complication was pulmonary thromboembolic, 6 in each group. Blood transfusion rate was higher in the SP group (6%) than in the RM group (< 1%).

Conclusions

Screening and RM can reduce 90-day complications in patients undergoing TKA.

Comparison of long-term kinematics and wear of total knee arthroplasty implant designs

We sought to evaluate wear and kinematics in well-established implants of posterior stabilized (PS) and cruciate retaining (CR) designs. Ninety-one knees implanted for at least five years were examined. The implants were Genesis II PS (Smith & Nephew, Memphis, TN), Sigma PS (DePuy Synthes, Warsaw, IN), or Sigma CR. Radiostereometric analysis (RSA) images were acquired at multiple flexion angles and the 3D positions of the implant components were determined using model-based RSA software. The location of the center of the contact area between the femoral and polyethylene components was used to obtain contact kinematics, and the magnitude of the virtual intersection between the components indicated linear wear. All three groups had paradoxical anterior motion on both condyles, experienced similar net external rotation, and exhibited instances of internal rotation during flexion. The maximum observed wear rate was significantly greater for the Sigma PS than the Genesis II PS on the medial condyle (mean difference = 0.032 mm/year, p = 0.044), but not the lateral condyle, while there was no difference between the Sigma PS and Sigma CR for either condyle. Knees with lateral condylar separation had greater maximum wear rates on the medial condyle (mean difference = 0.033 mm/year, p = 0.001), while those with medial condylar separation had greater maximum wear rates on the lateral condyle (mean difference = 0.044 mm/year, p = 0.014). At long term follow-up in patients with well-functioning implants, there were differences in kinematics and wear resistance between implants. These results suggest that implant design affects long-term kinematics and wear in well-functioning implants and that condylar separation should be avoided to minimize wear.

Comparison of in vivo knee kinematics before and after bicruciate-stabilized total knee arthroplasty during squatting

Background

No studies have directly evaluated kinematic changes during squatting before and after bicruciate-stabilized total knee arthroplasty (BCS-TKA) with the dual cam-post mechanism and asymmetric surfaces. This study investigated the effect of BCS-TKA on changes to pre- and postoperative skeletal knee kinematics, to identify factors associated with postoperative skeletal kinematic parameters.

Methods

Seventeen knees in 17 patients were prospectively recruited before primary TKA for advanced medial knee osteoarthritis. Subjects underwent BCS-TKA and were evaluated more than 1 year postoperatively. In vivo dynamic skeletal knee kinematics were evaluated using periodic radiographic images collected during squatting to quantify the tibiofemoral functional extension/flexion angle, anteroposterior (AP) translation, and axial rotation angle using image-matching techniques. Rotational alignments of femoral and tibial components were measured postoperatively using computed tomography images.

Results

The pre- and postoperative tibiofemoral functional extension/flexion angles during squatting were 12.2° ± 6.7°/100.1° ± 16.8° and 9.6° ± 8.6°/109.4° ± 16.8°, respectively, with a significant difference in flexion angle (p < .05). Total AP translation was significantly larger postoperatively than preoperatively (10.8 mm ± 3.7 mm vs. 14.4 mm ± 4.2 mm, respectively; p < .05). The pre- and postoperative total rotation angles were 6.6° ± 3.0° and 6.4° ± 3.7°, respectively, indicating no significant difference. The pre- and postoperative tibiofemoral functional flexion angles were significantly associated with each other (p = .0434, r = .49). The postoperative total rotation angle was significantly smaller when the total component rotational mismatch angle between the femoral and tibial components was above 5° vs. below 5° (4.6° ± 2.7° vs. 8.3° ± 3.9°, respectively; p < .05).

Conclusions

BCS-TKA significantly increased the tibiofemoral functional flexion angles, with larger AP translation postoperatively. Both preoperative skeletal kinematics and surgical techniques affected the skeletal kinematics of the replaced knee. A total component rotational mismatch angle greater than 5° significantly decreased postoperative total knee rotation during squatting.

Optimal designs and surgical technique for hip and knee joint replacement: The best is yet to come!

Over the last three decades, there have been significant advancements in knee and hip replacement technology. The implants and the surgical technology we now have to aid in their implantation are advancing and improving functional outcomes and survivorship. Despite these advancements, there are still issues with patient satisfaction, functional limitations, and early revisions due to instability and aseptic loosening. This article reviews the state of current technology in hip and knee replacement implant design and surgical technique, and reviews some of the current implant designs and surgical technologies that may be able to solve some of the most common issues in the knee and hip replacement surgery.

Effect of gap balancing and measured resection techniques on implant migration and contact kinematics of a cementless total knee arthroplasty

BACKGROUND

The purpose of this study was to compare implant migration and tibiofemoral contact kinematics of a cementless primary total knee arthroplasty (TKA) implanted using either a gap balancing (GB) or measured resection (MR) surgical technique.

METHODS

Thirty-nine patients underwent TKA via a GB (n = 19) or a MR (n = 20) surgical technique. Patients received an identical fixed-bearing, cruciate-retaining cementless implant. Patients underwent a baseline radiostereometric analysis (RSA) exam at two weeks post-operation, with follow-up visits at six weeks, three months, six months, and one year post-operation. Migration including maximum total point motion (MTPM) of the femoral and tibial components was calculated over time. At the one year visit patients also underwent a kinematic exam via RSA.

RESULTS

Mean MTPM of the tibial component at one year post-operation was not different (mean difference = 0.09 mm, p = 0.980) between the GB group (0.85 ± 0.37 mm) and the MR group (0.94 ± 0.41 mm). Femoral component MTPM at one year post-operation was also not different (mean difference = 0.27 mm, p = 0.463) between the GB group (0.62 ± 0.34 mm) and the MR group (0.89 ± 0.44 mm). Both groups displayed similar kinematic patterns.

CONCLUSIONS

There was no difference in implant migration and kinematics of a single-radius, cruciate retaining cementless TKA performed using a GB or MR surgical technique. The magnitude of migration suggests there is low risk of early loosening. The results provide support for using the cementless implant with either a GB or MR technique.

Effects of the Medial Plateau Bearing Insert Conformity on Mid-Flexion Paradoxical Motion in a Posterior-Stabilized Total Knee Arthroplasty Design

BACKGROUND

One of the most common kinematic abnormalities reported for posterior-stabilized (PS) total knee arthroplasty (TKA) design is paradoxical anterior sliding during early and mid-flexion. PS TKAs have been designed such that the cam-post mechanism does not engage until later in flexion, making these implants vulnerable to anterior sliding during early and mid-flexion. The objective of this study is to investigate the biomechanical effect of increasing bearing conformity on a PS TKA.

METHODS

Using a validated computational model of the knee joint, the sagittal conformity of the medial plateau of a PS TKA design was altered. Three scenarios were created and evaluated for mechanics: (1) baseline conformity, (2) increased conformity, and (3) decreased conformity.

RESULTS

From full extension to approximately 70° of knee flexion, the medial condyle demonstrated minimal anterior sliding for the increased medial conformity design but revealed anterior sliding of 2 and 4 mm for the baseline and decreased conformity designs, respectively. After cam-post engagement, the medial condyle consistently rolled back for all 3 designs. The lateral condyle experienced consistent rollback throughout the entire flexion range for all 3 designs. However, femorotibial contact force was higher for the increased conformity design, peaking at 3.13 times body weight (×BW) compared to 3.0 × BW contact force for other 2 designs.

CONCLUSION

Increasing medial conformity of the bearing insert appears to reduce mid-flexion sliding for PS TKA designs, although this comes at the expense of increased femorotibial forces. This could be due to kinematic conflicts that may be introduced with highly constraining designs.

Trial Tibial Inserts May Result in Different Knee Kinematics from Final Poly Inserts in Total Knee Arthroplasty

INTRODUCTION

Trialling is a key step in total knee arthroplasty (TKA) and helps the surgeon assess for adequate balancing, range of motion, and stability. Despite this, there are no studies investigating knee kinematics when using trial versus final polyethylene tibial inserts.

MATERIALS AND METHODS

Fourteen fresh frozen cadaveric specimens were cycled in a VIVO joint motion simulator. Using both simple compression and simulated muscle loads, joints were tested after TKA with a trial insert or a final tibial poly insert. Anterior/posterior (AP), internal/external (IE), and varus/valgus (VV) kinematics and laxities were analyzed.

RESULTS

Knees with trial poly inserts had significantly greater AP hysteresis (difference between flexion and extension motion) than those with final poly inserts (p=0.001). There was no significant difference in IE (p=0.563) or VV (p=0.580) hysteresis. There was no difference in AP, IE, or VV motion or laxities when considering the flexion path alone. Prosthetic joints followed different paths in flexion versus extension.

CONCLUSION

While trial tibial inserts impart valuable information, they may not accurately reproduce the same joint kinematics as final inserts. Balancing of the knee at specific degrees of flexion may depend on the path taken to get there.

Restoration of Joint Inclination in Total Knee Arthroplasty Offers Little Improvement in Joint Kinematics in Neutrally Aligned Extremities

Kinematically aligned total knee replacements have been shown to better restore physiological kinematics than mechanical alignment and also offer good postoperative satisfaction. The purpose of this study is to evaluate the extent to which an inclined joint line in a kinematically aligned knee can alter the postoperative kinematics. A multi-body dynamic simulation was used to identify kinematic changes in the joint. To accurately compare mechanical alignment, kinematic alignment and a natural knee, a “standard” patient with neutral alignment of the lower extremities was selected for modeling from a joint database. The arthroplasty models in this study were implanted with a single conventional cruciate-retaining prosthesis. Each model was subjected to a flexion movement and the anteroposterior translation of the femoral condyles was collected for kinematic analysis. The results showed that the mechanical alignment model underwent typical paradoxical anterior translation of the femoral condyles. Incorporating an inclined joint line in the model did not prevent the paradoxical anterior translation, but a 3° varus joint line in the kinematic alignment model could reduce the peak value of this motion by about 1 mm. Moreover, the inclined joint line did not restore the motion curve back to within the range of the kinematic curve of the natural knee. The results of this study suggest that an inclined joint line, as in the kinematic alignment model, can slightly suppress paradoxical anterior translation of the femoral condyles, but cannot restore kinematic motions similar to the physiological knee. This finding implies that prostheses intended to be used for kinematic alignment should be designed to optimize knee kinematics with the intention of restoring a physiological motion curve.

In vivo kinematics and cruciate ligament forces in bicruciate-retaining total knee arthroplasty

We analyzed the effects of bicruciate-retaining total knee arthroplasty (BCR-TKA) on knee kinematics and cruciate ligament forces. Patients (N = 15) with osteoarthritis (OA) and an intact anterior cruciate ligament (ACL) underwent magnetic resonance imaging and single-plane fluoroscopy to measure tibiofemoral kinematics during two deep knee bend activities before and after BCR-TKA: (1) weight-bearing squat; (2) non-weight-bearing cross-legged sitting. Forces in ligament bundles were calculated using VivoSim. The dynamic range of varus-valgus angulation decreased from 3.9 ± 4.4° preoperatively to 2.2 ± 2.7° postoperatively. Preoperatively, the medial femoral condyle translated anteriorly from 10° to 50° of flexion, and posteriorly beyond 50° of flexion. Postoperatively, the medial and lateral femoral condyles translated posteriorly throughout flexion in a medial pivot pattern. ACL forces were high in extension and decreased with flexion pre- and postoperatively. PCL forces increased with flexion preoperatively and did not change significantly postoperatively. Preoperatively, ACL forces correlated with anteroposterior translation of the femoral condyles. Postoperatively, PCL forces correlated with anteroposterior translation of the lateral femoral condyle. BCR-TKA altered knee kinematics during high flexion activity which correlated significantly with changes in cruciate ligament forces.

Knee Arthroplasty and Gait: Effect on Level Walking-An Overview

BACKGROUND

Knee arthroplasty (KA) aims to restore normal gait, correct joint alignment, improve the quality of life and activities of daily living, and provide pain relief. Hence, the main purpose of this overview was to summarise data from published reviews exploring gait changes during unaided level walking post-KA, thereby providing for recommendations for future practice and research.

METHOD

A systematic review of review (RoR) for articles published in English and since 2010, was conducted online using PubMed and Google Scholar, as per Preferred Reporting Items for Systematic reviews and Metaanalyses guidelines. Predefined eligibility criteria were applied, and the data thus compiled were analysed. Study quality was assessed using AMSTAR-2 checklist.

RESULT

A total of 5 systematic reviews and meta-analysis consisting of 58 primary studies were included in the review. Based on the very limited evidence, it appears that though gait does not normalize post-KA, there seems to be an improvement in spatiotemporal gait parameters over mid to long term with some decline in gains over long term. Further reviews also suggest no benefits with unicompartmental KA in comparison to healthy controls or total KA patients. Further quality of the study was found to be of critically low confidence based on the AMSTAR-2 scale, suggesting that the results should be interpreted with great caution.

CONCLUSION

The overview highlights the knowledge gap and limitations in gait assessment research post-KA with existing heterogeneity in methods and reporting amidst other factors within primary studies, establishing the need for further research.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s43465-020-00342-w.

Contact kinematics of patient-specific instrumentation versus conventional instrumentation for total knee arthroplasty

BACKGROUND

The goal was to evaluate the joint contact kinematics of total knee arthroplasties implanted using patient-specific instrumentation (PSI) compared to conventional instrumentation (CI). We hypothesized that use of PSI would not significantly alter contact kinematics.

METHODS

The study was a prospective randomized controlled trial, with equal allocation of fifty patients to PSI and CI groups. At two years post-operation, patients underwent weight-bearing stereo X-ray examinations at 0°, 20°, 40°, 60°, 80°, and 100° of flexion. The shortest tibiofemoral distance on each condyle determined the contact location. Magnitude of the shortest distance was measured and condylar separation was analyzed using thresholds of 0.5 and 0.75 mm. Kinematic measurements derived from the shortest distance included anteroposterior (AP) translation, excursion, axial rotation, and paradoxical anterior motion. Pivot position and cam/post contact were also investigated.

RESULTS

There were no differences (p > 0.05) in medial and lateral AP contact locations, excursions, and magnitude of anterior motion, or in axial rotation, pivot patterns, frequency of cam/post engagement, frequency of medial anterior motion, and condylar separation at a 0.75 mm threshold. Significant differences were found in frequency of lateral anterior motion (p = 0.048) and condylar separation at a 0.5 mm threshold (p = 0.010). Both groups displayed typical kinematics for a fixed-bearing posterior-stabilized implant.

CONCLUSIONS

We found no major differences in knee kinematics between PSI and CI groups, which suggest that PSI does not provide a significant kinematic advantage over conventional instruments.

Oxford domed lateral unicompartmental knee arthroplasty

AIMS

To report mid- to long-term results of Oxford mobile bearing domed lateral unicompartmental knee arthroplasty (UKA), and determine the effect of potential contraindications on outcome.

METHODS

A total of 325 consecutive domed lateral UKAs undertaken for the recommended indications were included, and their functional and survival outcomes were assessed. The effects of age, weight, activity, and the presence of full-thickness erosions of cartilage in the patellofemoral joint on outcome were evaluated.

RESULTS

Median follow-up was seven years (3 to 14), and mean age at surgery was 65 years (39 to 90). Median Oxford Knee Score (OKS) was 43 (interquartile range (IQR) 37 to 47), with 260 (80%) achieving a good or excellent score (OKS > 34). Revisions occurred in 34 (10%); 14 (4%) were for dislocation, of which 12 had no recurrence following insertion of a new bearing, and 12 (4%) were revised for medial osteoarthritis (OA). Ten-year survival was 85% (95% confidence interval (CI) 79 to 90, at risk 72). Age, weight, activity, and patellofemoral erosions did not have a significant effect on the clinical outcome or survival.

CONCLUSION

Domed lateral UKA provides a good alternative to total knee arthroplasty (TKA) in the management of lateral compartment OA. Although dislocation is relatively easy to treat successfully, the dislocation rate of 4% is high. It is recommended that the stability of the bearing is assessed intraoperatively. If the bearing can easily be displaced, the fixed rather than the mobile bearing version of the Oxford lateral tibial component should be inserted instead. Younger age, heavier weight, high activity, and patellofemoral erosions did not detrimentally affect outcome, so should not be considered contraindications. Cite this article: Bone Joint J 2020;102-B(8):1033-1040.

Is high tibial osteotomy better than proximal fibula osteotomy for treating knee osteoarthritis? A protocol for a systematic review and meta-analysis of clinical controlled trials

BACKGROUND

Knee osteoarthritis (KOA) is a common disease in the elderly, which seriously reduces the quality of life of patients and increases the social burden. proximal fibula osteotomy (PFO) and high tibial osteotomy (HTO) are effective methods to treat KOA. However, it is not entirely clear which method has the advantage. Therefore, we evaluated the efficacy and safety of HTO and PFO in the treatment of KOA.

METHODS

Randomized controlled trials from online databases including PubMed, Embase, the Cochrane Library, China National Knowledge Infrastructure, Chinese Scientific Journal Database, Wanfang Data and Chinese Biomedical Literature Database that compared the efficacy of HTO and PFO in the treatment of KOA were retrieved. The main outcomes included hospital for special surgery (HSS) knee scores, knee society knee scoring system (KSS) score, visual analog scale (VAS) knee pain scores, western ontario and McMaster universities osteoarthritis index score, operation time, intraoperative bleeding volume, hospitalization time, complications. The Cochrane risk of bias tool was used to assess methodological quality.

RESULTS

The literature will provide a high-quality analysis of the current evidence supporting HTO for KOA based on various comprehensive assessments including HSS scores, KSS score, VAS scores, western Ontario and McMaster universities osteoarthritis index score, operation time, intraoperative bleeding volume, hospitalization time, and complications.

CONCLUSION

This proposed systematic review will provide up-to-date evidence to assess the effect of HTO in the treatment for patients with KOA.

Comparison of Contact Kinematics in Posterior-Stabilized and Cruciate-Retaining Total Knee Arthroplasty at Long-Term Follow-Up

BACKGROUND

There is controversy regarding the superiority of posterior-stabilizing (PS) total knee arthroplasty (TKA) and cruciate-retaining (CR) TKA. Substantial work has made comparisons between PS and CR TKA at follow-ups of less than 5 years. It was the goal of the present study to compare the kinematics at greater than 5 years postoperatively between CR and PS TKA, with a secondary goal of comparing patient function.

METHODS

A total of 42 knees were investigated, with equal representation in the PS and CR TKA groups. Patients underwent radiostereometric analysis imaging at 0°, 20°, 40°, 60° 80°, and 100° of flexion. Contact position, magnitude of excursion, and condylar separation on each condyle were measured. A Timed-Up-and-Go functional test was also performed by patients, with the total test time being measured. Preoperative and postoperative clinical outcome scores were also collected.

RESULTS

There were differences in contact position on both the medial and lateral condyles at multiple angles of flexion (P < .05). There was no difference (P = .89) in medial excursion; however, PS TKA had greater lateral excursion than CR TKA (P < .01). No difference (P > .99) was found in frequency of condylar separation. PS TKA was associated with faster (P = .03) total Timed-Up-and-Go test times. There were no differences in clinical outcome scores between the groups preoperatively or postoperatively.

CONCLUSION

We found kinematic and functional differences that favor PS TKA. Our results suggest posterior cruciate ligament insufficiency in CR TKA, indicating that perhaps the cam/post systems in PS TKA better maintain knee kinematics and function long term.