Conjugation of laccase from the white rot fungus Trametes versicolor to chitosan and its utilization for the elimination of triclosan

Biotreatment efficiency, degradation mechanism and bacterial community structure in an immobilized cell bioreactor treating triclosan-rich wastewater

Biotreatment of triclosan is mainly performed in conventional activated sludge systems, which, however, are not capable of completely removing this antibacterial agent. As a consequence, triclosan ends up in surface and groundwater, constituting an environmental threat, due to its toxicity to aquatic life. However, little is known regarding the diversity and mechanism of action of microbiota capable of degrading triclosan. In this work, an immobilized cell bioreactor was setup to treat triclosan-rich wastewater. Bioreactor operation resulted in high triclosan removal efficiency, even greater than 99.5%. Nitrogen assimilation was mainly occurred in immobilized biomass, although nitrification was inhibited. Based on Illumina sequencing, Bradyrhizobiaceae, followed by Ferruginibacter, Thermomonas, Lysobacter and Gordonia, were the dominant genera in the bioreactor, representing 38.40 ± 0.62% of the total reads. However, a broad number of taxa (15 genera), mainly members of Xanthomonadaceae, Bradyrhizobiaceae and Chitinophagaceae, showed relative abundances between 1% and 3%. Liquid Chromatography coupled to Quadrupole Time-Of-Flight Mass Spectrometry (LC-QTOF-MS) resulted in the identification of catabolic routes of triclosan in the immobilized cell bioreactor. Seven intermediates of triclosan were detected, with 2,4-dichlorophenol, 4-chlorocatechol and 2-chlorohydroquinone being the key breakdown products of triclosan. Thus, the immobilized cell bioreactor accommodated a diverse bacterial community capable of degrading triclosan.

Applications and immobilization strategies of the copper-centred laccase enzyme; a review

Laccase is a multi-copper enzyme widely expressed in fungi, higher plants, and bacteria which facilitates the direct reduction of molecular oxygen to water (without hydrogen peroxide production) accompanied by the oxidation of an electron donor. Laccase has attracted attention in biotechnological applications due to its non-specificity and use of molecular oxygen as secondary substrate. This review discusses different applications of laccase in various sectors of food, paper and pulp, waste water treatment, pharmaceuticals, sensors, and fuel cells. Despite the many advantages of laccase, challenges such as high cost due to its non-reusability, instability in harsh environmental conditions, and proteolysis are often encountered in its application. One of the approaches used to minimize these challenges is immobilization. The various methods used to immobilize laccase and the different supports used are further extensively discussed in this review.

Laccase-assisted degradation of emerging recalcitrant compounds - A review

The main objective of this review is to provide up to date, brief, irrefutable, organized data on the conducted experiments on a range of emerging recalcitrant compounds such as Diclofenac (DCF), Chlorophenols (CPs), tetracycline (TCs), Triclosan (TCS), Bisphenol A (BPA) and Carbamazepine (CBZ). These compounds were selected from the categories of pharmaceutical contaminants (PCs), endocrine disruptors (EDs) and personal care products (PCPs) on the basis of their toxicity and concentration retained in the environment. In this context, detailed mechanism of laccase mediated degradation has been conversed that laccase assisted degradation occurs by one electron oxidation involving redox potential as underlying element of the process. Further, converging towards biotechnology, laccase immobilization increased removal efficiency, storage and reusability through various experimentally conducted studies. Laccase is being considered noteworthy as mediators facilitate laccase in oxidation of non-phenolic compounds and thereby increasing its substrate range which is being discussed in further in the review. The laccase assisted degradation mechanism of each compound has been elucidated but further studies to undercover proper degradation mechanisms needs to be performed.

Chitosan-based blends for biomedical applications

Polysaccharides are the most abundant naturally available carbohydrate polymers; composed of monosaccharide units covalently connected together. Chitosan is the most widely used polysaccharides because of its exceptional biocompatibility, mucoadhesion, and chemical versatility. However, it suffers from a few drawbacks, e.g. poor mechanical properties and antibacterial activity for biomedical applications. Blending chitosan with natural or synthetic polymers may not merely improve its physicochemical and mechanical properties, but may also improve its bioactivity-induced properties. This review paper summarizes progress in chitosan blends with biodegradable polymers and polysaccharides and their biomedical applications. Blends of chitosan with alginate, starch, cellulose, pectin and dextran and their applications were particularly addressed. The critical and challenging aspects as well as the future ahead of the use of chitosan-based blends were eventually enlightened.

Advances in laccase-triggered anabolism for biotechnology applications

This is the first comprehensive overview of laccase-triggered anabolism from fundamental theory to biotechnology applications. Laccase is a typical biological oxidordeuctase that induces the one-electronic transfer of diverse substrates for engendering four phenoxy radicals with concomitant reduction of O₂ into 2H₂O. In vivo, laccase can participate in anabolic processes to create multifarious functional biopolymers such as fungal pigments, plant lignins, and insect cuticles, using mono/polyphenols and their derivatives as enzymatic substrates, and is thus conducive to biological tissue morphogenesis and global carbon storage. Exhilaratingly, fungal laccase has high redox potential (E° = 500-800 mV) and thermodynamic efficiency, making it a remarkable candidate for utilization as a versatile catalyst in the green and circular economy. This review elaborates the anabolic mechanisms of laccase in initiating the polymerization of natural phenolic compounds and their derivatives in vivo via radical-based self/cross-coupling. Information is also presented on laccase immobilization engineering that expands the practical application ranges of laccase in biotechnology by improving the enzymatic catalytic activity, stability, and reuse rate. Particularly, advances in biotechnology applications in vitro through fungal laccase-triggered macromolecular biosynthesis may provide a key research direction beneficial to the rational design of green chemistry.

Recent environmental applications of and development prospects for immobilized laccase: a review

Laccases have enormous potential as promising 'green' biocatalysts in environmental applications including wastewater treatment and polluted soil bioremediation. The catalytic oxidation reaction they perform uses only molecular oxygen without other cofactors, and the only product after the reaction is water. The immobilization of laccase offers several improvements such as protected activity and enhanced stability over free laccase. In addition, the reusability of immobilized laccase is adistinct advantage for future applications. This review covers the sources of and progress in laccase research, and discusses the different methodologies of laccase immobilization that have emerged in the recent 5-10 years, as well as its applications to environmental fields, and evaluates these emerging technologies. Abbreviations: (2,4,6-TCP): 2,4,6-trichlorophenol; (2,4-DCP): 2,4-dichlorophenol; (ABTS), 2,2-azinobis (3-ethylbenzothiazoline-6-sulfonic acid); (ACE), acetaminophen; (BC-AS), almond shell; (BC-PM), pig manure; (BC-PW), pine wood; (BPA), bisphenol A; (BPA), bisphenol A; (BPF), bisphenol F; (BPS), bisphenol S; (C₆₀), fullerene; (Ca-AIL), calcium-alginate immobilized laccase; (CBZ), carbamazepine; (CETY), cetirizine; (CHT-PGMA-PEI-Cu (II) NPs), Cu (II)-chelated chitosan nanoparticles; (CLEAs), cross-linked enzyme aggregates; (CMMC), carbon-based mesoporous magnetic composites; (COD), chemical oxygen demand; (CPH), ciprofloxacin hydrochloride; (CS), chitosan; (CTC), chlortetracycline; (Cu-AIL), copper-alginate immobilized laccase; (DBR K-4BL), Drimarene brilliant red K-4BL; (DCF), diclofenac; (E1),estrone; (E2), 17 β-estradiol; (EDC), 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride; (EDCs), endocrine disrupting chemicals; (EE2), 17α-ethinylestradiol; (EFMs), electrospun fibrous membranes; (FL), free laccase; (fsMP), fumed silica microparticles; (GA-CBs), GLU-crosslinked chitosan beads; (GA-CBs), glutaraldehyde-crosslinked chitosan beads; (GA-Zr-MOF), graphene aerogel-zirconium-metal organic framework; (GLU), glutaraldehyde; (GO), graphene oxide; (HMCs), hollow mesoporous carbon spheres; (HPEI/PES), hyperbranched polyethyleneimine/polyether sulfone; (IC), indigo carmine; (IL), immobilized laccase; (k_cat), catalytic constant; (K_m), Michealis constant; (M-CLEAs), Magnetic cross-linked enzyme aggregates; (MMSNPs-CPTS-IDA-Cu²⁺), Cu²⁺-chelated magnetic mesoporous silica nanoparticles; (MSS), magnetic mesoporous silica spheres; (MWNTs), multi-walled carbon nanotubes; (MWNTs), multi-walled carbon nanotubes; (NHS), N-hydroxy succinimide; (O-MWNTs), oxidized-MWNTs; (P(AAm-NIPA)), poly(acrylamide-N-isopropylacrylamide); (p(GMA)), poly(glycidyl methacrylate); (p(HEMA)), poly(hydroxyethyl methacrylate); (p(HEMA-g-GMA)-NH₂, poly(glycidyl methacrylate) brush grafted poly(hydroxyethyl methacrylate); (PA6/CHIT), polyamide 6/chitosan; (PAC), powdered active carbon; (PAHs), polycyclic aromatic hydrocarbons; (PAM-CTS), chitosan grafted polyacrylamide hydrogel; (PAN/MMT/GO), polyacrylonitrile/montmorillonite/graphene oxide; (PAN/PVdF), polyacrylonitrile/polyvinylidene fluoride; (PEG), poly ethylene glycol; (PEI), Poly(ethyleneimine); (poly(4-VP)), poly(4-vinyl pyridine); (poly(GMA-MAA)), poly(glycidyl methacrylate-methacrylic acid); (PVA), polyvinyl alcohol; (RBBR), Remazol Brilliant Blue R; (SDE), simulated dye effluent; (semi-IPNs), semi-interpenetrating polymer networks; (TC), tetracycline; (TCH), tetracycline hydrochloride; (TCS), triclosan; (Vmax), maximum activity; (Zr-MOF, MMU), micro-mesoporous Zr-metal organic framework.

Innovative hydrolysis of corn stover biowaste by modified magnetite laccase immobilized nanoparticles

Intensive studies have been performed on the improvement of bioethanol production by transformation of lignocellulose biomass. In this study, the digestibility of corn stover was dramatically improved by using laccase immobilized on Cu²⁺ modified recyclable magnetite nanoparticles, Fe₃O₄-NH₂. After digestion, the laccase was efficiently separated from slurry. The degradation rate of lignin reached 40.76%, and the subsequent cellulose conversion rate 38.37% for 72 h at 35 °C with cellulase at 50 U g^-1 of corn stover. Compared to those of free and inactivated mode, the immobilized laccase pre-treatment increased subsequent cellulose conversion rates by 23.98% and 23.34%, respectively. Moreover, the reusability of immobilized laccase activity remained 50% after 6 cycles. The storage and thermal stability of the fixed laccase enhanced by 70% and 24.1% compared to those of free laccase at 65 °C, pH 4.5, respectively. At pH 10.5, it exhibited 16.3% more activities than its free mode at 35 °C. Our study provides a new avenue for improving the production of bioethanol with immobilized laccase for delignification using corn stover as the starting material.

Degradation of Anthracene by Immobilizing Laccase From Trametes Versicolor onto Chitosan Beads and Hyacinth Plant

Polycyclic aromatic hydrocarbons (PAHs) are recognized as a toxic, mutagenic and/or carcinogenic compounds, and their pollution of soil and aquifer is of increasing environmentally risk. Laccases (E.C. 1.10.3.2) are phenoloxidases catalyze the oxidation of PAHs in the presence of a mediator compound and hyacinth plant. In this study laccase from Trametes versicolor was immobilized into chitosan, and the potential to oxidize anthracene in the presence of 1-hydroxybenzotriazole (HBT) was examined. Results indicated that the immobilization enhanced the stability of laccase against temperature, pH, inhibitors and loading time compared with the other cases. The immobilized laccase-mediator system was as efficient as the free enzyme for oxidizing the tested PAHs. After 24h. of incubation, immobilized laccase–HBT showed a system oxidization more than immobilized laccase without (HBT) of PAHs; Chitosan with hyacinth plant and (HBT) resulted better conversion than chitosan with or without HBT. These results indicate a new chance for applying the immobilized laccase in bioremediation.

Miniaturized systems for evaluating enzyme activity in polymeric membrane bioreactors

Enzyme-coated polymeric membranes are versatile catalysts for biofuel production and other chemical production from feedstock, like plant biomass. Such bioreactors are more energy efficient than high temperature methods because enzymes catalyze chemical reactions near room temperature. A major challenge in processing plant biomass is the presence of lignin, a complex aromatic polymer that resists chemical breakdown. Therefore, membranes coated with enzymes such as laccase that can degrade lignin are sought for energy extraction systems. We present an experimental study on optimizing an enzyme-based membrane bioreactor and investigate the tradeoff between high flow rate and short dwell time in the active region. In this work, zero flow rate voltammetry experiments confirm the electrochemical activity of Trametes versicolor laccase on conductive polymer electrodes, and a flow-through spectroscopy device with laccase-coated porous nylon membranes is used with a colorimetric laccase activity indicator to measure the catalysis rate and percent conversion as a function of reactant flow rate. Membrane porosity before and after laccase coating is verified with electron microscopy.

Physical entrapment of chitosan in fixed-down-flow column bed enhances triclosan removal from water

Triclosan (TCS) is an emergent pollutant with wide-ranging deleterious effects on aquatic organisms and humans. There is a growing concern about the development of low-cost and efficient treatment systems for the removal of TCS from water. This report describes the performance of a prototype of a continuous flow, fixed bed column device with physically entrapped industrial by-product chitosan. The effects of initial TCS concentration, adsorbent dose in the column matrix, and flow rate were investigated with regard to removal efficiency (%), adsorption capacity and breakthrough time. To understand the thermodynamic properties of the adsorption process, three kinetic models - Thomas, Yoon-Nelson and Adams-Bohart - were applied to the experimental data for the prediction of characteristic parameters of the adsorption process. The Yoon-Nelson model showed the best agreement between the experimental and calculated values. The column showed a near saturation state (C_t/C₀ = 0.92; C₀ and C_t are the concentration of TCS before and after treatment.) at 90 mg L^-1 TCS concentration after 60 minutes. In view of non-availability of a treatment process for the emergent pollutant TCS, the data of the present investigation will facilitate the development of novel prototypes of column bed reactors for the removal of TCS.

Aptitude of Oxidative Enzymes for Treatment of Wastewater Pollutants: A Laccase Perspective

Natural water sources are very often contaminated by municipal wastewater discharges which contain either of xenobiotic pollutants and their sometimes more toxic degradation products, or both, which frustrates the universal millenium development goal of provision of the relatively scarce pristine freshwater to water-scarce and -stressed communities, in order to augment their socioeconomic well-being. Seeing that both regulatory measures, as regards the discharge limits of wastewater, and the query for efficient treatment methods remain unanswered, partially, the prospects of enzymatic treatment of wastewater is advisable. Therefore, a reconsideration was assigned to the possible capacity of oxidative enzymes and the respective challenges encountered during their applications in wastewater treatment, and ultimately, the prospects of laccase, a polyphenol oxidase that oxidizes aromatic and inorganic substrates with electron-donating groups in treatment aromatic contaminants of wastewater, in real wastewater situations, since it is assumed to be a vehicle for a greener community. Furthermore, the importance of laccase-driven catalysis toward maintaining mass-energy balance, hence minimizing environmental waste, was comprehensibly elucidated, as well the strategic positioning of laccase in a model wastewater treatment facility for effective treatment of wastewater contaminants.

A catechol biosensor based on immobilizing laccase to Fe3O4@Au core-shell nanoparticles

This work is directed towards the synthesis of the magnetic nanoparticle in a core and a gold shell with immobilized of laccase on its surface (Fe₃O₄@Au@ Lac). The prepared Fe₃O₄@Au@ Lac core/shell nanoparticles are characterized by means TEM, SEM, DLS, zeta potential, UV-Vis, and TGA. Meanwhile, as an example of the applications, Biosensor activity was investigated by using the oxidation of catechol and recording the UV-Vis absorption in the 402 nm wavelength. The biosensor also demonstrated optimum activity at pH 5.0, reaction time at 40 min, and 35 mg the amount of biosensor. Linear response in the catechol concentration range of 5.0-70.0 μM. The limit of detection and the apparent Michaels-Menten constant (K_m) of the biosensor were 2 μM and 15 μM respectively.

Combined Cross-Linked Enzyme Aggregates as Biocatalysts

Enzymes are efficient biocatalysts providing an important tool in many industrial biocatalytic processes. Currently, the immobilized enzymes prepared by the cross-linked enzyme aggregates (CLEAs) have drawn much attention due to their simple preparation and high catalytic efficiency. Combined cross-linked enzyme aggregates (combi-CLEAs) including multiple enzymes have significant advantages for practical applications. In this review, the conditions or factors for the preparation of combi-CLEAs such as the proportion of enzymes, the type of cross-linker, and coupling temperature were discussed based on the reaction mechanism. The recent applications of combi-CLEAs were also reviewed.

Characterisation of electron beam irradiation-immobilised laccase for application in wastewater treatment

Laccase from Phoma sp. UHH 5-1-03 was cross-linked to polyvinylidene fluoride membranes by electron beam irradiation. Immobilised laccase displayed a higher stability than the non-immobilised enzyme with respect to typical wastewater temperatures, and pH at a range of 5 to 9. Batch tests addressed the removal of pharmaceutically active compounds (PhACs; applied as a mixture of acetaminophen, bezafibrate, indometacin, ketoprofen, mefenamic acid, and naproxen) by both immobilised and non-immobilised laccase in municipal wastewater. High removal rates (>85%) of the most efficiently oxidised PhACs (acetaminophen and mefenamic acid) indicated a high efficiency of the immobilised laccase in wastewater. Continuous elimination of the aforementioned PhACs by the immobilised enzyme in a continuously operated diffusion basket reactor yielded a PhAC removal pattern qualitatively similar to those observed in batch tests. Clearly higher apparent V_max values and catalytic efficiencies (in terms of both V_max/S_0.5 as well as V_max/K_m values obtained from data fitting according to the Hill and the Michaelis-Menten model, respectively) observed for acetaminophen oxidation by the immobilised compared to the non-immobilised enzyme are in support of a considerably higher functional stability of the immobilised laccase especially in wastewater. The potential influence of acetaminophen on the removal of comparatively less laccase-oxidisable water pollutants such as the antimicrobial triclosan (TCS) was investigated. TCS was increasingly removed upon increasing the initial acetaminophen concentration in immobilised as well as non-immobilised laccase reaction systems until saturation became evident. Acetaminophen was consumed and not recycled during laccase reactions, which was accompanied by the formation of various acetaminophen-TCS cross-coupling products. Nevertheless, the simultaneous presence of acetaminophen (and potentially even more pollutant removal-enhancing laccase substrates) and more recalcitrant pollutants in wastewater represents an interesting option for the efficiency enhancement of enzyme-based wastewater treatment approaches.

Degradation of triclosan by environmental microbial consortia and by axenic cultures of microorganisms with concerns to wastewater treatment

Triclosan is an antimicrobial agent, which is widely used in personal care products including toothpaste, soaps, deodorants, plastics, and cosmetics. Widespread use of triclosan has resulted in its release into wastewater, surface water, and soils and has received considerable attention in the recent years. It has been reported that triclosan is detected in various environmental compartments. Toxicity studies have suggested its potential environmental impacts, especially to aquatic ecosystems. To date, removal of triclosan has attracted rising attention and biodegradation of triclosan in different systems, such as axenic cultures of microorganisms, full-scale WWTPs, activated sludge, sludge treatment systems, sludge-amended soils, and sediments has been described. In this study, an extensive literature survey was undertaken, to present the current knowledge of the biodegradation behavior of triclosan and highlights the removal and transformation processes to help understand and predict the environmental fate of triclosan. Experiments at from lab-scale to full-scale field studies are shown and discussed.

Extraction and characterization of chitosan from prawn shell waste and its conjugation with cutinase for enhanced thermo-stability

The present article describes extraction of chitosan from prawn shells waste and its application in thermal stabilization of Fusarium sp. ICT SAC1 cutinase by non-covalent and covalent conjugation. Extracted chitosan represented 78.40% degree of deacetylation (DDA), a molecular weight of 173 kDa and was soluble in 1% acetic acid with 2.8 ± 0.15% insoluble matter. The structural (FTIR, NMR and XRD) and thermal characterization (DSC and TGA) indicated unique properties for chitosan. Plausible chitosan structure was also deduced. The water and fat binding capacities were 923% and 598.05% while 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) and 1,1-diphenyl-2-picrylhydrzyl radicals scavenging activity was 60.62 and 11.83 μM Trolox-Equivalent/ml. The K_m and V_max values of free cutinase were 0.82 mM and 20.64 mM/min which increased by 14.63 and 17.07%; and 27.18 and 43.94% after non-covalent and covalent conjugation, respectively. A marginal increment in thermal inactivation constants and energy (k_d, t_1/2, D and E_d value) were also noticed for cutinase-chitosan conjugates. The enthalpy, free energy and entropy values increased marginally in covalent conjugate vis-à-vis non-covalent conjugated and free cutinase. A reduction in α-helix, random coils and β-sheets content was noted after conjugation.

Immobilized Cerrena sp. laccase: preparation, thermal inactivation, and operational stability in malachite green decolorization

Laccases are polyphenol oxidases with widespread applications in various industries. In the present study, the laccase from Cerrena sp. HYB07 was immobilized with four methods, namely entrapment in alginate, covalently binding to chitosan as well as formation of cross-linked enzyme aggregates (CLEAs) and magnetic CLEAs (M-CLEAs). The activity recovery rates of the immobilized laccases ranged from 29% to 68%. Immobilization elevated the reaction temperature optimum and reduced substrate specificity, but not necessarily the turnover rate. pH stability of immobilized laccases was improved compared with that of the free laccase, especially at acidic pH values. Thermal inactivation of all laccases followed a simple first-order exponential decay model, and immobilized laccases displayed higher thermostability, as manifested by lower thermal inactivation rate constants and longer enzyme half-life time. Operational stability of the immobilized laccase was demonstrated by decolorization of the triphenylmethane dye malachite green (MG) at 60 °C. MG decolorization with free laccase was accompanied by a shift of the absorption peak and accumulation of a stable, colored intermediate tetradesmethyl MG, probably due to lower thermostability of the free laccase and premature termination of the degradation pathway. In contrast, complete decolorization of MG was achieved with laccase CLEAs at 60 °C.

Laccases: Production, Expression Regulation, and Applications in Pharmaceutical Biodegradation

Laccases are a family of copper-containing oxidases with important applications in bioremediation and other various industrial and biotechnological areas. There have been over two dozen reviews on laccases since 2010 covering various aspects of this group of versatile enzymes, from their occurrence, biochemical properties, and expression to immobilization and applications. This review is not intended to be all-encompassing; instead, we highlighted some of the latest developments in basic and applied laccase research with an emphasis on laccase-mediated bioremediation of pharmaceuticals, especially antibiotics. Pharmaceuticals are a broad class of emerging organic contaminants that are recalcitrant and prevalent. The recent surge in the relevant literature justifies a short review on the topic. Since low laccase yields in natural and genetically modified hosts constitute a bottleneck to industrial-scale applications, we also accentuated a genus of laccase-producing white-rot fungi, Cerrena, and included a discussion with regards to regulation of laccase expression.

Laccase encapsulation in chitosan nanoparticles enhances the protein stability against microbial degradation

A novel concept with the result of enzyme stabilization against microbial degradation in real bioremediation processes was developed through the encapsulation of laccase in chitosan nanoparticles. Besides of abundant information on laccase-chitosan conjugates, we report the laccase encapsulation into nanoparticles based in chitosan. The chitosan-tripolyphosphate technique was applied for the production of morphologically homogeneous enzymatic nanoparticles, with high enzyme encapsulation efficiency, small asymmetric sizes (from 40 to 90 nm), and rough surfaces. Contrary to macroscopic immobilized enzymes, temperature and pH activity profiles of nano-sized laccase were similar to those of free enzyme. The substrate affinity constant (K M) of nano-encapsulated laccase was similar to these from free enzyme, while its activity rate constant (k cat) represented 60 % of these obtained with free enzyme. Importantly, stability of nano-encapsulated laccase against microbial degradation in soil, compost, and wastewater was significantly increased. After 24 h exposure to wastewater from a treatment plant, the laccase activity of the nanoparticles was 82.8 % of initial activity, compared with only 7.8 % retained activity for free enzyme. After 36 h incubation in compost extract, the laccase nanoparticles showed 72.4 % of the initial activity, while the free enzyme was almost completely inactivated. Finally, after 84 h incubation in soil extract, the nanoparticles and free preparations showed 57.9 and 17.3 % of the initial activity, respectively. Thus, the nanoencapsulation of enzymes able to transform pollutants is an alternative to improve the operational lifetime of enzymes in real environmental applications.

Assessing the use of nanoimmobilized laccases to remove micropollutants from wastewater

Enzymes immobilization is a useful way to allow enzyme reuse and increase their stability. A high redox potential laccase from Trametes versicolor (TvL) and a low redox potential, but commercially available low-cost laccase from Myceliophthora thermophila (MtL), were successfully immobilized and co-immobilized onto fumed silica nanoparticles (fsNP). Enzyme loads of 1.78 ± 0.07, 0.69 ± 0.03, and 1.10 ± 0.01 U/mg fsNP were attained for the optimal doses of TvL, MtL, and co-immobilized laccases, respectively. In general, the laccase-fsNP conjugates showed a higher resistance against an acidic pH value (i.e., pH 3), and a higher storage stability than free enzymes. In addition, immobilized enzymes exhibited a superior long-term stability than free laccases when incubated in a secondary effluent from a municipal wastewater treatment plant (WWTP). For instance, the residual activity after 2 weeks for the co-immobilized laccases and the mixture of free laccases were 40.2 ± 2.5% and 16.8 ± 1.0%, respectively. The ability of the laccase-fsNP to remove a mixture of (14)C-bisphenol A (BPA) and (14)C-sodium diclofenac (DCF) from spiked secondary effluents was assessed in batch experiments. The catalytic efficiency was highly dependent on both the microbial source and state of the biocatalyst. The high redox potential TvL in free form attained a four-fold higher percentage of BPA transformation than the free MtL. Compared to free laccases, immobilized enzymes led to much slower rates of BPA transformation. For instance, after 24 h, the percentages of BPA transformation by 1000 U/L of a mixture of free laccases or co-immobilized enzymes were 67.8 ± 5.2 and 27.0 ± 3.9%, respectively. Nevertheless, the use of 8000 U/L of co-immobilized laccase led to a nearly complete removal of BPA, despite the unfavorable conditions for laccase catalysis (pH ~ 8.4). DCF transformation was not observed for any of the enzymatic systems, showing that this compound is highly recalcitrant toward laccase oxidation under realistic conditions.

Towards high potential magnetic biocatalysts for on-demand elimination of pharmaceuticals

The present study investigated the applicability of a laccase based bioprocess for the treatment of a mixture containing 13 selected pharmaceuticals. To do so, laccase was immobilized as cross-linked enzyme aggregates (MAC-CLEAs) on amine functionalized magnetic nanoparticles using chitosan/1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide hydrochloride (EDAC) as the cross-linking system. The activity recovery of laccase reached 61.4% under the optimal conditions of MAC-CLEAs formation. The latter exhibited enhanced storage stability over one year at 4°C and showed better temperature resistance compared to its soluble counterpart. The biocatalysts were properly recycled and the catalytic activity recovery was good even after a hundred and fifty batch reactions. Complete removal of pharmaceuticals like acetaminophen, diclofenac, mefenamic acid, atenolol and epoxy carbamazepine and partial removal of fenofibrate, diazepam, trimethoprim, and ketoprofen by laccase was achieved within 12h of incubation, whereas efficient removal of indometacin required the presence of mediator.

A comparison between the oxidation with laccase and horseradish peroxidase for triclosan conversion

Triclosan is a broad-spectrum biocide used in personal-care products that is suspected to be linked to the emergence of antibiotic-resistant bacteria. In the present work, the enzymes horseradish peroxidase and laccase from Trametes versicolor were evaluated for the conversion of triclosan in an aqueous matrix. The removal of antibacterial activity by the enzymatic processes was evaluated by an assay based on the growth inhibition of Escherichia coli K12. The horseradish peroxidase (HRP) process appears more advantageous than the laccase process in removing triclosan from an aqueous matrix, considering the reaction parameters pH, temperature, catalytic efficiency, and enzyme concentration. The highest conversion of triclosan catalysed by laccase was observed at pH 5.0, that is, lower than the typical pH range (6.5-7.5) of sewage treatment plants' effluents. The efficiency of laccase process was much more impacted by variations in the temperature in the range of 10-40°C. Kinetic studies showed that triclosan is a substrate more specific for HRP than for laccase. The protein content for the HRP-catalysed process was 14 times lower than that for the laccase process. Decay kinetics suggest that reaction mechanisms depend on enzyme concentration and its concentration. Both processes were able to reduce the antibacterial activity, and the residual activity of the treated solution is probably due to non-converted triclosan and not due to the reaction products. The laccase-catalysed conversion of triclosan in an environmental relevant concentration required a higher amount of enzyme than that required in the HRP process.

The comparative study of a laccase-natural clinoptilolite-based catalyst activity and free laccase activity on model compounds

For the first time a laccase from Trametes versicolor was immobilized on a natural clinoptilolite with Si/Al=5 to obtain a biocatalyst for environmental applications. Immobilization procedures exploiting adsorption and covalent binding were both tested, and only the last provided enough activity for practical applications. The optimal conditions for the immobilization of the enzyme on the support and the kinetic parameters for the free and covalent bonded laccase were determined. The laccase bonded to the zeolitic support showed a lower activity than the free laccase, but the pH and thermal stability were greater. 20 mg of dry biocatalyst containing 1 U of laccase were able to remove in 50h 73-78% of 2-chlorophenol and 2,4-dichlorophenol in relatively concentrated aqueous solutions (100 μmol L(-1)).

Fostering the action of versatile peroxidase as a highly efficient biocatalyst for the removal of endocrine disrupting compounds

Response surface methodology (RSM) was used to optimize the removal of five endocrine disrupting compounds (EDCs) by the enzyme versatile peroxidase (VP): bisphenol A (BPA), triclosan (TCS), estrone (E1), 17β-estradiol (E2) and 17α-ethinylestradiol (EE2). The optimal variables of enzyme activity (90-100 U L(-1)), sodium malonate (29-43 mM) and MnSO4 (0.8-1 mM) led to very high removal rates of the five pollutants (2.5-5.0 mg L(-1) min(-1)). The structural elucidation of transformation products arising from the enzymatic catalysis of the EDCs was investigated by Gas Chromatography coupled to Mass Spectrometry (GC-MS) and Liquid Chromatography Electrospray Time-of-Flight Mass Spectrometry (LC-ESI-TOF-MS). The presence of dimers and trimers, indicative of oxidative coupling, was demonstrated.

Laccase immobilized manganese ferrite nanoparticle: synthesis and LSSVM intelligent modeling of decolorization

Laccase was immobilized onto manganese ferrite nanoparticle (MFN) and dye decolorization from single and binary systems was studied. The characteristics of laccase immobilized manganese ferrite nanoparticle (LIMFN) were investigated using Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). Direct red 31 (DR31), Acid blue 92 (AB92) and Direct green 6 (DG6) were used. A least square support vector machine (LSSVM) was developed to predict the decolorization efficiency of various single and binary systems based on the obtained laboratory data under different experimental conditions. Statistical and graphical quality measures were also employed to evaluate the performance and accuracy of the developed intelligent models. It is shown that the predictions of the designed LSSVM models are in close agreement with the experimental data. The effects of LIMFN dosage, pH and dye concentration on dye decolorization from single and binary systems were evaluated. Decolorization kinetics followed Michaelis-Menten Model.

Laccases to take on the challenge of emerging organic contaminants in wastewater

The removal of emerging organic contaminants from municipal wastewater poses a major challenge unsatisfactorily addressed by present wastewater treatment processes. Enzyme-catalyzed transformation of emerging organic contaminants (EOC) has been proposed as a possible solution to this major environmental issue more than a decade ago. Especially, laccases gained interest in this context in recent years due to their broad substrate range and since they only need molecular oxygen as a cosubstrate. In order to ensure the stability of the enzymes and allow their retention and reuse, either immobilization or insolubilization of the biocatalysts seems to be the prerequisite for continuous wastewater treatment applications. The present review summarizes the research conducted on EOC transformation with laccases and presents an overview of the possible immobilization techniques. The goal is to assess the state of the art and identify the next necessary steps that have to be undertaken in order to implement laccases as a tertiary wastewater treatment process in sewage treatment plants.

Substrate specificity and enzyme recycling using chitosan immobilized laccase

The immobilization of laccase (Aspergillus sp.) on chitosan by cross-linking and its application in bioconversion of phenolic compounds in batch reactors were studied. Investigation was performed using laccase immobilized via chemical cross-linking due to the higher enzymatic operational stability of this method as compared to immobilization via physical adsorption. To assess the influence of different substrate functional groups on the enzyme's catalytic efficiency, substrate specificity was investigated using chitosan-immobilized laccase and eighteen different phenol derivatives. It was observed that 4-nitrophenol was not oxidized, while 2,5-xylenol, 2,6-xylenol, 2,3,5-trimethylphenol, syringaldazine, 2,6-dimetoxyphenol and ethylphenol showed reaction yields up 90% at 40 °C. The kinetic of process, enzyme recyclability and operational stability were studied. In batch reactors, it was not possible to reuse the enzyme when it was applied to syringaldazne bioconversion. However, when the enzyme was applied to bioconversion of 2,6-DMP, the activity was stable for eight reaction batches.

Electron beam-induced immobilization of laccase on porous supports for waste water treatment applications

The versatile oxidase enzyme laccase was immobilized on porous supports such as polymer membranes and cryogels with a view of using such biocatalysts in bioreactors aiming at the degradation of environmental pollutants in wastewater. Besides a large surface area for supporting the biocatalyst, the aforementioned porous systems also offer the possibility for simultaneous filtration applications in wastewater treatment. Herein a "green" water-based, initiator-free, and straightforward route to highly reactive membrane and cryogel-based bioreactors is presented, where laccase was immobilized onto the porous polymer supports using a water-based electron beam-initiated grafting reaction. In a second approach, the laccase redox mediators 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) and syringaldehyde were cross-linked instead of the enzyme via electron irradiation in a frozen aqueous poly(acrylate) mixture in a one pot set-up, yielding a mechanical stable macroporous cryogel with interconnected pores ranging from 10 to 50 µm in size. The membranes as well as the cryogels were characterized regarding their morphology, chemical composition, and catalytic activity. The reactivity towards waste- water pollutants was demonstrated by the degradation of the model compound bisphenol A (BPA). Both membrane- and cryogel-immobilized laccase remained highly active after electron beam irradiation. Apparent specific BPA removal rates were higher for cryogel- than for membrane-immobilized and free laccase, whereas membrane-immobilized laccase was more stable with respect to maintenance of enzymatic activity and prevention of enzyme leakage from the carrier than cryogel-immobilized laccase. Cryogel-immobilized redox mediators remained functional in accelerating the laccase-catalyzed BPA degradation, and especially ABTS was found to act more efficiently in immobilized than in freely dissolved state.

Polyethyleneglycol diacrylate microspheres: a novel carrier for laccase immobilisation

Laccase was immobilised on polyethyleneglycol diacrylate (PEGDA) microspheres. The optimal preparation conditions of PEGDA microspheres were as follows: 3.0% (w/v) 2,2-azobisisobutyro-nitrite (AIBN), 4.0-5.0% (w/v) polyvinylpyrrolidone (PVP), 5.0-8.0% (w/v) glucose and 4.0% (w/v) PEGDA in glucose solution. The volume ratio of PEGDA solution, glucose/PVP solution and AIBN solution was 25: 100: 1. Microspheres obtained exhibited good characteristics with small sizes (1-4 µm). The immobilised laccase showed a higher stability in a wide pH range. Thermal stability and storage stability of immobilised laccase were enhanced. The activity of immobilised laccase was 45.0% after six cycles uses. Only 62.7% of the activity remained for free laccase while there was a 60.4% increased for immobilised laccase with storage at 4 °C for 25 d. The Km value of laccase increased from 21.9 to 114.0 µmol/l after immobilisation.

Electroactive nanobiomolecular architectures of laccase and cytochrome c on electrodes: applying silica nanoparticles as artificial matrix

Fully electroactive multilayer architectures combining the redox protein cytochrome c and the enzyme laccase by the use of silica nanoparticles as artificial matrix have been constructed on gold electrodes capable of direct dioxygen reduction. Laccase form Trametes versicolor and cytochrome c from horse heart were electrostatically coimmobilized by alternate deposition with interlayers of silica nanoparticles in a multilayer fashion. The layer formation has been monitored by quartz crystal microbalance. The electrochemical properties and performance of the nanobiomolecular entities were investigated by cyclic voltammetry, indicating, that a multistep electron transfer cascade, from the electrode via cytochrome c in the layered system toward the enzyme laccase, and here to molecular dioxygen was achieved. The response of the novel architecture is based on direct electron exchange between immobilized proteins and can be tuned by the assembly process.

Characterization of combined cross-linked enzyme aggregates from laccase, versatile peroxidase and glucose oxidase, and their utilization for the elimination of pharmaceuticals

In order to transform a wide range of pharmaceutically active compounds (PhACs), the three oxidative enzymes laccase (Lac) from Trametes versicolor, versatile peroxidase (VP) from Bjerkandera adusta and glucose oxidase (GOD) from Aspergillus niger were concomitantly cross-linked after aggregation, thus, making a combined cross-linked enzyme aggregate (combi-CLEA) that was versatile and involved in an enzymatic cascade reaction. From the initial enzymes about 30% of initial laccase activity was recovered along with 40% for each of VP and GOD. The combi-CLEA showed good results in conditions close to those of real wastewater (neutral pH and medium temperature) as well as a good ability to resist to denaturing conditions such as high temperature (60°C) and low pH (3). Batch experiments were realized to test the free enzyme's ability to degrade, a PhACs cocktail, mainly in a synthetic wastewater containing acetaminophen, naproxen, mefenamic acid, indometacin, diclofenac, ketoprofen, caffeine, diazepam, ciprofloxacin, trimethoprim, fenofibrate and bezafibrate, carbamazepine and its by-product 10-11 epoxy-carbamazepine. High removal was achieved (more than 80%) for the five first compounds. Then, the elimination ability of the combi-CLEA with or without hydrogen peroxide, glucose or manganese sulfate was determined. Globally, our results demonstrated that VP has a wider removal spectrum than Lac. These removal features are enhanced under more specific conditions, whereas the combi-CLEA combined advantages of both VP and laccase. Finally, the elimination of PhACs in a municipal wastewater treatment plant effluent using the combi-CLEA was marginally investigated. Concentrations of most of the selected PhACs were below the limit of quantification (lower than 20 ng/L) except for acetaminophen. Its combi-CLEA-mediated removal reached up to 25%.

Chitosan improves stability of carbon nanotube biocathodes for glucose biofuel cells

We demonstrate a novel combined chitosan–carbon-nanotube–enzyme biocathode with a fibrous microstructure that improves the performance by creating a protective microenvironment, preventing the loss of the electrocatalytic activity of the enzyme, and providing good oxygen diffusion.

Formation of enzyme polymer engineered structure for laccase and cross-linked laccase aggregates stabilization

Laccase and laccase-based cross-linked enzyme aggregates (CLEAs) were stabilized through the formation of a surrounding polymeric network made of chitosan and 3-aminopropyltriethoxysilane. The thermoresistance of the resulting enzyme polymer engineered structures of laccase (EPES-lac) and CLEAs (EPES-CLEA) were more than 30 times higher than that of free laccase and CLEAs at pH 3 and 40 °C. The EPES showed higher residual activity than the unmodified biocatalysts against chaotropic salts (up to 10 times), EDTA (up to 5 times), methanol (up to 15 times) and acetone (up to 20 times). The Michaelis-Menten kinetic parameters revealed that the affinity for 2,2'-azino-bis-(3-ethylbenzothiazoline-6-sulphonic acid) has doubled for the EPES-lac and EPES CLEA compared to their unmodified forms. The EPES-lac structures acted optimally at pH 4 and their activity was nearly temperature-independent, while the laccase activity of EPES-CLEA was optimal at pH 4 and 60 °C. Globally, the EPES have shown significantly improved properties which make them attractive candidate for the development of laccase-based applications.

Laccase immobilization and insolubilization: from fundamentals to applications for the elimination of emerging contaminants in wastewater treatment

Over the last few decades many attempts have been made to use biocatalysts for the biotransformation of emerging contaminants in environmental matrices. Laccase, a multicopper oxidoreductase enzyme, has shown great potential in oxidizing a large number of phenolic and non-phenolic emerging contaminants. However, laccases and more broadly enzymes in their free form are biocatalysts whose applications in solution have many drawbacks rendering them currently unsuitable for large scale use. To circumvent these limitations, the enzyme can be immobilized onto carriers or entrapped within capsules; these two immobilization techniques have the disadvantage of generating a large mass of non-catalytic product. Insolubilization of the free enzymes as cross-linked enzymes (CLEAs) is found to yield a greater volume ratio of biocatalyst while improving the characteristics of the biocatalyst. Ultimately, novel techniques of enzymes insolubilization and stabilization are feasible with the combination of cross-linked enzyme aggregates (combi-CLEAs) and enzyme polymer engineered structures (EPESs) for the elimination of emerging micropollutants in wastewater. In this review, fundamental features of laccases are provided in order to elucidate their catalytic mechanism, followed by different chemical aspects of the immobilization and insolubilization techniques applicable to laccases. Finally, kinetic and reactor design effects for enzymes in relation with the potential applications of laccases as combi-CLEAs and EPESs for the biotransformation of micropollutants in wastewater treatment are discussed.

Elimination of bisphenol a and triclosan using the enzymatic system of autochthonous colombian forest fungi

Bisphenol A (BPA) and triclosan (TCS) are known or suspected potential endocrine disrupting chemicals (EDCs) which may pose a risk to human health and have an environmental impact. Enzyme preparations containing mainly laccases, obtained from Ganoderma stipitatum and Lentinus swartzii, two autochthonous Colombian forest white rot fungi (WRF), previously identified as high enzyme producers, were used to remove BPA and TCS from aqueous solutions. A Box-Behnken factorial design showed that pH, temperature, and duration of treatment were significant model terms for the elimination of BPA and TCS. Our results demonstrated that these EDCs were extensively removed from 5 mg L⁻¹ solutions after a contact time of 6 hours. Ninety-four percent of TCS and 97.8% of BPA were removed with the enzyme solution from G. stipitatum; 83.2% of TCS and 88.2% of BPA were removed with the L. swartzii enzyme solution. After a 6-hour treatment with enzymes from G. stipitatum and L. swartzii, up to 90% of the estrogenic activity of BPA was lost, as shown by the yeast estrogen screen assay. 2,2-Azino-bis-(3-ethylthiazoline-6-sulfonate) (ABTS) was used as a mediator (laccase/mediator system) and significantly improved the laccase catalyzed elimination of BPA and TCS. The elimination of BPA in the absence of a mediator resulted in production of oligomers of molecular weights of 454, 680, and 906 amu as determined by mass spectra analysis. The elimination of TCS in the same conditions produced dimers, trimers, and tetramers of molecular weights of 574, 859, and 1146 amu. Ecotoxicological studies using Daphnia pulex to determine lethal concentration (LC₅₀) showed an important reduction of the toxicity of BPA and TCS solutions after enzymatic treatments. Use of laccases emerges thus as a key alternative in the development of innovative wastewater treatment technologies. Moreover, the exploitation of local biodiversity appears as a potentially promising approach for identifying new efficient strains for biotechnological applications.