Different effects of ozone and aqueous ammonia in a combined pretreatment method on rice straw and dairy manure fiber for enhancing biomethane production

Combining pretreatments and co-fermentation as successful approach to improve biohydrogen production from dairy cow manure

The present paper is focused on enhancing the production of biohydrogen (bioH2) from dairy cow manure (DCM) through dark fermentation (DF). Two enhancement production strategies have been tested: i) the combination of H2O2 with sonification as pretreatment and ii) the co-fermentation with cheese whey as co-substrate. Concerning the pretreatment, the best combination was investigated according to the response surface methodology (RSM) by varying H2O2 dosage between 0.0015 and 0.06 g/gTS and ultrasonic specific energy input (USEI) between 35.48 and 1419.36 J/gTS. The increase of carbohydrates concentration was used as target parameter. Results showed that the combination of 0.06 g/gTS of H2O2 with 1419.36 J/gTS of USEI maximized the concentration of carbohydrates. The optimized conditions were used to pretreat the substrate prior conducting DF tests. The use of pretreatment resulted in obtaining a cumulative bioH2 volume of 51.25 mL/L and enhanced the bioH2 production by 125% compared to the control test conducted using raw DCM. Moreover, the second strategy, i.e. co-fermentation with cheese whey (20% v/v) as co-substrate ended up to enhancing the DF performance as the bioH2 production reached a value of 334.90 mL/L with an increase of 1372% compared to the control DF test. To further improve the process, dark fermentation effluents (DFEs) were valorized via photo fermentation (PF), obtaining an additional hydrogen production aliquot.

New insights into the sustainable use of soluble straw humic substances for the remediation of multiple heavy metals in contaminated soil

This study addresses the research gap in understanding the differences in straw decomposition and variations in humic substances (HS) extracted from various treatment conditions. The aim is to explore the potential of soluble straw HS in remediating heavy metal pollution in soils. The study characterizes straw decomposition structures using scanning electron microscopy (SEM) and X-ray diffraction (XRD), while employing gel permeation chromatography (GPC) and fluorescence spectroscopy (EEM) to analyze the molecular weight and degree of humification of extracted straw HS. The removal efficiency of HS for heavy metals is assessed, with a focus on aerobic humic substances (AE-HS) showing the highest potential for heavy metal removal. Spectral analysis and mass spectrometry analysis reveal the role of phenolic compounds, carboxylic acids, and aromatic compounds in AE-HS, forming humates or complexes to remove heavy metals from contaminated soil. Notably, the optimized AE-HS achieved the highest removal efficiency of 96.18 %, 82.75 %, 60.43 %, and 41.66 % for cadmium, copper, zinc, and lead, respectively. This study provides new insights into the preparation of straw for use as a heavy metal remover and has implications for the use of straw humic substances in soil remediation.

Experimental investigation on mechanical properties of aged bamboo fiber-reinforced composites under quasi-static loading

Bamboo fiber-reinforced composites (BFRC) have gradually attracted the interest of researchers due to their excellent mechanical properties. However, the age factor can affect these composites' mechanical properties and weaken them. This study aims to explore the mechanical properties of BFRC subjected different aging tests. First, the BFRC is prepared from raw bamboo through a series of technological processes. Second, the BFRC sheets are processed into tensile and compressive samples with different directions. Third, the samples are treated with a cold-hot test and a UV dry-wet test, respectively. Finally, quasi-static experiments are carried out to study the mechanical properties of aged BFRC. The results reveal that the BFRC has significant anisotropy. The tensile strength of BFRC parallel with the axis of the reinforcing fiber is as high as 148.53 MPa. It is 26.47 times greater than the tensile strength of BFRC perpendicular to the axis of the reinforcing fiber. The mechanical responses and SEM images show that the UV dry-wet test significantly affects on the BFRC compared to the cold-hot test. It dramatically reduces the mechanical properties of the BFRC. The SEM images further indicate that cracks occur on the surface of BFRC samples under the UV dry-wet test. In addition, two aging tests have an interactive effect on BFRC, which can reduce the sensitivity of BFRC to a UV dry-wet environment. These results are expected to deepen the understanding of the mechanical properties of BFRC and provide guidance for its applicable conditions.

Effect of time and temperature of pretreatment and anaerobic co-digestion of rice straw and swine wastewater by domesticated paddy soil microbes

Rice straw and swine wastewater are abundant, easy to obtain, and inexpensive biomass materials. Anaerobic digestion of rice straw and swine wastewater effectively regulates the carbon-to-nitrogen ratio and also improves methane production efficiency. The dense lignocellulosic structure, unsuitable carbon-to-nitrogen ratio, and light texture of rice straw hinder its application in anaerobic digestion. Effective pretreatment technologies can improve degradation efficiency and methane production. Our study is the first to apply domesticated paddy soil microbes to enhance the efficiency of hydrolytic acidification of rice straw and swine wastewater at varying temperatures and times. The results show that the highest total organic carbon (1757.2 mg/L), soluble chemical oxygen demand (5341.7 mg/L), and organic acid concentration (4134.6 mg/L) appeared in the hydrolysate after five days of hydrolytic acidification at 37 °C. Moreover, the use of hydrolysate produced 13% more gas and reduced the anaerobic digestion period by ten days compared to the untreated control. This suggests that using domesticated paddy soil microbes as a pretreatment might be a sustainable and cost-effective strategy for improving the degradation efficacy and methane production from lignocellulosic materials.

Highly digestible nitrogen-enriched straw upgraded by ozone-urea pretreatment: Digestibility metrics and energy-economic analysis

Ozone is a powerful oxidative gas widely used as a green pretreatment to enhance the delignification of cereal straws. Urea pretreatment can enrich straws with nitrogen to make them more accessible to anaerobic microorganisms. This study aimed to evaluate the effect of ozone-urea pretreatment on the digestibility of wheat straw (i.e., physicochemical, nitrogen enrichment, gas production, nutritional value, and surface chemistry). The results of ozone-urea pretreatment were compared with non-pretreated, ozone-pretreated, and urea-pretreated samples. This pretreatment method outperformed the other methods in terms of digestibility metrics. The ozone-urea pretreatment resulted in a 50% reduction in lignin, a 4.2 times increase in crude protein, a 22.5% increase in bonded organic-N, a 2 times increase in 24 h-gas production, and a 43.67% increase in total digestible nutrients compared to the non-pretreated sample. Based on the total digestible nutrients index, one-tonne ozone-urea-pretreated straw would be 70.6 USD cheaper than the non-pretreated one.

Assessment Impacts of Ozone on Salmonella Typhimurium and Escherichia coli O157:H7 in Liquid Dairy Waste

Liquid dairy manure, which is produced in enormous quantities in flush dairy manure management systems, is commonly used as an alternative to chemical fertilizers. It provides nutrient benefits to crops and soils. While dairy waste is a well-accepted and widely used fertilizer, the presence of indicator organisms and human pathogens in manure may lead to pathogen contamination in crops and soils. This study is focused on the examination of ozone gas-based sterilization. In the past, ozone (O3) has been used for sanitizing various foods and solid surfaces, but the potential of O3 for eliminating human pathogens in liquid dairy waste is not studied yet. Pathogens such as Salmonella Typhimurium and Escherichia coli O157:H7 are reported to be present in liquid dairy manure, and this research evaluated the effects of various levels of ozone on the survival of these two pathogens. We designed a continuous type O3 treatment system that has four major components: (1) ozone generator using oxygen; (2) ozone concentration control by mixing with pure air; (3) continuous monitoring of ozone concentrations; and (4) ozone experiment chambers. Various levels of ozone (43.26, 87.40, and 132.46 mg·L−1) were produced in the ozone system, and subsequently, ozone was diffused through liquid manure. Liquid manure was exposed to ozone for multiple durations (30, 60, and 120 min). To determine the effectiveness of O3 in eliminating pathogens, time-series samples were collected and analyzed for determining the levels of S. typhimurium and E. coli O157:H7. Preliminary results showed that ozone concentrations of 132.46 mg/L, and exposure time of 120 min resulted in the reduced levels of E. coli and Salmonella. Low levels of ozone and limited exposure time were found to be less effective in pathogen removal potentially due to high solid contents. Additional studies carrying out experiments to evaluate the impacts of solids in combination with ozone concentrations will provide further insights into developing full-scale ozone-based treatment systems.

Ozone assisted autohydrolysis of wheat bran enhances xylooligosaccharide production with low generation of inhibitor compounds: A comparative study

In the present study, ozone assisted autohydrolysis (OAAH) was evaluated for enhanced generation of xylooligosaccharide (XOS) from wheat bran. The total XOS yield with optimum ozone dose of 3% (OAAH-3) was found to be 8.9% (w/w biomass) at 110 °C in comparison to 7.96% at 170 °C by autohydrolysis (AH) alone. Although, there was no significant difference in oligomeric composition (DP 2-6), significant decrease in degradation products namely furfural (2.78-fold), HMF (3.15-fold), acrylamide (nil) and acetic acid (1.06-fold), was observed with OAAH-3 as a pretreatment option. There was 1-fold higher xylan to XOS conversion and OAAH-hydrolysate had higher DPPH radical scavenging activity than AH. PCA plots indicated clear enhancement in XOS production and lower generation of inhibitors with decrease in treatment temperature. Results of the study therefore suggest OAAH can be an effective pretreatment option that can further be integrated with downstream processing for concentration and purification of XOS.

Volatile Fatty Acid Production from Organic Waste with the Emphasis on Membrane-Based Recovery

In recent years, interest in the biorefinery concept has emerged in the utilization of volatile fatty acids (VFAs) produced by acidogenic fermentation as precursors for various biotechnological processes. This has attracted substantial attention to VFA production from low-cost substrates such as organic waste and membrane based VFA recovery techniques to achieve cost-effective and environmentally friendly processes. However, there are few reviews which emphasize the acidogenic fermentation of organic waste into VFAs, and VFA recovery. Therefore, this article comprehensively summarizes VFA production, the factors affecting VFA production, and VFA recovery strategies using membrane-based techniques. Additionally, the outlook for future research on VFA production is discussed.

Effects of Mechanical Refining on Anaerobic Digestion of Dairy Manure

Mechanical refining (MR) is a cost-effective pretreatment in biochemical conversion processes that is employed to overcome biomass recalcitrance. This work studied the effects of MR on biogas and methane produced by the anaerobic digestion (AD) of dairy manure. The cumulative gas volume and yield from the AD of manure refined at 6k revolutions increased by 33.7 and 7.7% for methane and by 32.0 and 6.4% for biogas, respectively, compared to the unrefined manure. This enhancement was reached by increasing manure solubilization, reducing particle size, and achieving external fibrillation and internal delamination of fibers in manure. However, the highly refined manure (subjected to 60k revolutions) exhibited methane and biogas yields that were reduced by 9.5 and 1.5%, respectively. This decrease was observed because the pore structure was ruptured, and finely ground manure particles were aggregated together at high revolutions (60k), thereby inhibiting the release of organic matter from the manure. Therefore, this study indicates that the MR for pretreatment of dairy manure could have great potential for significantly enhancing AD of dairy manure. Further studies will include optimization of conditions of mechanical refining (i.e., mechanical intensity, process time), a continuous AD of dairy manure pretreated by the MR, and scale-up with cost evaluation.

Effect of acclimatized paddy soil microorganisms using swine wastewater on degradation of rice straw

Rice straw (RS) is one of abundant agricultural waste for biogas production in China. However, the low carbon-methane conversion rate limits its wide application due to the low degradation rate of RS during fermentation. This study investigated the effect of acclimatized paddy soil microorganisms using swine wastewater on degradation of RS before anaerobic digestion. The total organic carbon, reducing sugar and NH₄⁺-N content of paddy soil + RS + swine wastewater (PRS) (653.50 mg/L) was higher than that of other groups after 19 days. The carboxymethyl cellulose activity (4.01 IU), cellulose/lignin ratio (5.25) and the degradation rate of lignin (51.96%) in PRS were higher than those of other groups. The Firmicutes (21.02%), Chloroflexi (12.48%), Proteobacteria (20.92%), and Bacteroidetes (25.78%) were the main fermentation phyla in PRS during acclimatization. These results indicated that the acclimatized paddy soil microorganisms using swine wastewater (SW) could degrade RS more efficiently.

Strategies to boost anaerobic digestion performance of cow manure: Laboratory achievements and their full-scale application potential

Cow manure represents a surplus manure waste in agricultural food sectors, which requires proper disposal. Anaerobic digestion, in this regard, has raised global interest owing to its apparent environmental benefits, including simultaneous waste diminishment and renewable energy generation. However, dedicated intensifications are necessary to promote the degradation of recalcitrant lignocellulosic components of cow manure. Hence, this manuscript presents a review of how to exploit cow manure in anaerobic digestion through different incentives extensively at lab-scale and full-scale. These strategies comprise 1) co-digestion; 2) pretreatment; 3) introduction of additives (trace metals, carbon-based materials, low-cost composites, nanomaterials, and microbial cultures); 4) innovative systems (bio-electrochemical fields and laser irradiation). Results imply that co-digestion and pretreatment approaches gain the predominance on promoting the digestion performance of cow manure. Particularly, for the co-digestion scenario, the selection of lignin-poor co-substrate is highlighted to produce maximum synergy and pronounced removal of lignocellulosic compounds of cow manure. Mechanical, thermal, and biological (composting) pretreatments generate mild improvement at laboratory-scale and are proved applicable in full-scale facilities. It is noteworthy that the introduction of additives (Fe-based nanomaterials, carbon-based materials, and composites) is acquiring more attention and shows promising full-scale application potential. Finally, bio-electrochemical fields stand out in laboratory trials and may serve as future reactor modules in agricultural anaerobic digestion installations treating cow manure.

Anaerobic co-digestion of corn stover and chicken manure using continuous stirred tank reactor: The effect of biochar addition and urea pretreatment

The performance of biochar mediated anaerobic co-digestion (co-AD) of corn stover (CS) and chicken manure (CM) using continuous stirred tank reactor (CSTR) was studied. Results showed that urea pretreated CS (UPCS) and biochar addition in anaerobic digestion (AD) system can improve co-AD. The effect of urea pretreatment is similar to that of biochar addition, and their synergistic effect was apparent under medium and high OLR conditions. When the OLR was 4.2 and 6.3 g VS/L/d, the biochar mediated UPCS/CM co-AD operated stably with the VMP of 2.160 and 1.616 L/L/d, and VMP of the biochar mediated UPCS /CM were 32.8%-89.6% and 27.8%-96.4% higher than other reactors, respectively. The results reveal that urea pretreatment and biochar addition promoted AD process through strengthening the buffer capacity system established by ammonia nitrogen and volatile fatty acids and improving the degradation of lignocellulosic biomass.

A comprehensive review on the framework to valorise lignocellulosic biomass as biorefinery feedstocks

An effective pretreatment is the first step to enhance the digestibility of lignocellulosic biomass - a source of renewable, eco-friendly and energy-dense materials - for biofuel and biochemical productions. This review aims to provide a comprehensive assessment on the advantages and disadvantages of lignocellulosic pretreatment techniques, which have been studied at the lab-, pilot- and full-scale levels. Biological pretreatment is environmentally friendly but time consuming (i.e. 15-40 days). Chemical pretreatment is effective in breaking down lignocellulose and increasing sugar yield (e.g. 4 to 10-fold improvement) but entails chemical cost and expensive reactors. Whereas the combination of physical and chemical (i.e. physicochemical) pretreatment is energy intensive (e.g. energy production can only compensate 80% of the input energy) despite offering good process efficiency (i.e. > 100% increase in product yield). Demonstrations of pretreatment techniques (e.g. acid, alkaline, and hydrothermal) in pilot-scale have reported 50-80% hemicellulose solubilisation and enhanced sugar yields. The feasibility of these pilot and full-scale plants has been supported by government subsidies to encourage biofuel consumption (e.g. tax credits and mandates). Due to the variability in their mechanisms and characteristics, no superior pretreatment has been identified. The main challenge lies in the capability to achieve a positive energy balance and great economic viability with minimal environmental impacts i.e. the energy or product output significantly surpasses the energy and monetary input. Enhancement of the current pretreatment techno-economic efficiency (e.g. higher product yield, chemical recycling, and by-products conversion to increase environmental sustainability) and the integration of pretreatment methods to effectively treat a range of biomass will be the steppingstone for commercial lignocellulosic biorefineries.

Assessment of gaseous ozone treatment on Salmonella Typhimurium and Escherichia coli O157:H7 reductions in poultry litter

Poultry litter is used as soil amendment or organic fertilizer. While poultry litter is enriched with organic matter suitable for land, the presence of pathogens such as Salmonella in poultry litter is a concern. To investigate the effect of gaseous ozone on pathogen reductions in poultry litter, this study conducted a series of experiments that involved understanding of Salmonella Typhimurium and Escherichia coli O157:H7 inactivation at various doses of Ozone (O₃) in wet and dry poultry litter conditions. Previously, ozone treatment has been shown to disinfect the surface of foods and plant materials including fruits, juices, and wastewater, however, additional research are needed to better understand the impacts of ozone on treatment of soil amendments. Sanitizing methods capable of eliminating pathogens of soil amendments are crucial to mitigate disease outbreaks related with litter/manure-based fertilizers. In this study, a bench scale continuous ozone treatment system was designed to produce O₃ gas, with a range O₃ concentrations (7.15-132.46 mg·L^-1), monitor ozone concentrations continuously, and control the ozone exposure time (15 to 90 mins) to understand the effectiveness of O₃ in eliminating S. Typhimurium and E. coli O157:H7 in poultry litter. Results showed that 7.15 mg·L^-1 did not reduce the counts of S. Typhimurium until exposure to O₃ for 90 min. The O₃ concentrations of 43.26 ~ 132.46 mg·L^-1 exposure reduced the bacterial counts. Furthermore, the moisture content of poultry litter was found to be an influencing factor for pathogen reduction. The pathogen reduction rates were reduced when the moisture content was increased. At higher moisture content, high concentrations of O₃ (132.46 mg·L^-1) were needed for pathogen reductions. The moisture content of 30% or lower was found to be more effective for controlling pathogen levels in poultry litter. Our study demonstrates that gaseous O₃ treatment could be used as an additional decontamination technique to ensure the certain degree of microbiological safety of poultry litter based soil amendment.

Tracking strategic developments for conferring xylose utilization/fermentation by Saccharomyces cerevisiae

Purpose

Efficient ethanol production through lignocellulosic biomass hydrolysates could solve energy crisis as it is economically sustainable and ecofriendly. Saccharomyces cerevisiae is the work horse for lignocellulosic bioethanol production at industrial level. But its inability to ferment and utilize xylose limits the overall efficacy of the process.

Method

Data for the review was selected using different sources, such as Biofuels digest, Statista, International energy agency (IEA). Google scholar was used as a search engine to search literature for yeast metabolic engineering approaches. Keywords used were metabolic engineering of yeast for bioethanol production from lignocellulosic biomass.

Result

Through these approaches, interconnected pathways can be targeted randomly. Moreover, the improved strains genetic makeup can help us understand the mechanisms involved for this purpose.

Conclusion

This review discusses all possible approaches for metabolic engineering of yeast. These approaches may reveal unknown hidden mechanisms and construct ways for the researchers to produce novel and modified strains.

Recent advances on ammonia-based pretreatments of lignocellulosic biomass

Ammonia-based pretreatments have been extensively studied in the last decade as one of the leading pretreatment technologies for lignocellulose biorefining. Here, we discuss the key features and compare performances of several leading ammonia-based pretreatments (e.g., soaking in aqueous ammonia or SAA, ammonia recycled percolation or ARP, ammonia fiber expansion or AFEX, and extractive ammonia or EA). We provide detailed insight into the distinct physicochemical mechanisms employed during ammonia-based pretreatments and its impact on downstream bioprocesses (e.g., enzymatic saccharification); such as modification of cellulose crystallinity, lignin/hemicellulose structure, and other ultrastructural changes such as cell wall porosity. Lastly, a brief overview of process technoeconomics and environmental impacts are discussed, along with recommendations for future areas of research on ammonia-based pretreatments.

Biomass briquetting reduces the energy loss during long-term ensiling and enhances anaerobic digestion: A case study on rice straw

The present study evaluated the impact of briquetting prior to ensiling on rice straw characteristics and anaerobic digestion performance. Ensiling for 10 months significantly reduced cellulose, hemicellulose and lignin of the uncompressed straw by 50.3%, 61.6% and 34.6%, respectively. However, increase of briquetting ratio enhanced the cellulose and hemicellulose contents at different ensiling times. In addition, increasing of ensiling time significantly reduced the biogas yield, while the highest cumulative biogas yield of 313.8 L kg^-1 VS was obtained from rice straw ensiled for 7 days at 1:6 briquetting ratio. Interestingly, the maximum biogas productivity of 1:6 briquetted straw after 10 months ensiling was 17.7% higher than that of the uncompressed straw ensiled for 7 days. Thus, briquetting prior to ensiling is a favorable approach to reduce the mass loss for enhanced biogas yield and energy recovery.