From paper mill waste to single cell oil: Enzymatic hydrolysis to sugars and their fermentation into microbial oil by the yeast Lipomyces starkeyi

Biodiesel production from sewage sludge using supported heteropolyacid as heterogeneous acid catalyst

Phosphotungstic acid (HPW) and silicotungstic acid (HSiW) were tested as homogeneous and as heterogeneous catalysts (after immobilized on different supports as high surface area graphite -HSAG500-, montmorillonite -MMT- and alumina -Al2O3-) for the in situ transesterification of sewage sludge lipids. Both catalysts exhibited similar performance in homogeneous phase, with slightly higher biodiesel yield for HPW. When the different supports were tested with HPW, the maximum yield obtained follow the trend: MMT > HSAG500 > Al2O3, but a greater leaching of the heteropolyacid (HPA) was observed with MMT. Therefore, HSAG500 showed the best results with a good FAMEs profile. The percentage of active phase was optimized from 1 to 40%, reaching the optimum at 10%. A more heterogeneous surface is obtained with larger quantities, also favouring the HPA leaching. The reaction temperature and the use of sonication as pre-treatment were also optimized. The best results were obtained after sonication with HPW-HSAG500 (10%) as catalyst, catalyst/sludge ratio 1:2, MeOH/sludge ratio 33:1, 120 °C and 21 h of reaction time with a maximum biodiesel yield of 31.1 % (FAMEs/lipids). In view of the results obtained HPW supports on HSAG500 offers a novel alternative as heterogeneous acid catalyst for in situ transesterification using sewage sludge as raw material.

Extraction of biodiesel from vegetable waste hydrolysates and evaluation of its engine performance and emission characteristics

Recently, microbial oil has become one of the promising next-generation feedstocks for producing biodiesel. While microbial oil can be extracted from different sources, there is only limited work on microbial production from fruits and vegetables. In this work, biodiesel was extracted through a two-step process: microbial conversion of vegetable waste into microbial oil using Lipomyces starkeyi, followed by transesterification of microbial oil into biodiesel. The lipid accumulation, composition of microbial oil, and the fuel properties of biodiesel were evaluated. The microbial oil consisted mainly of C16:0, C18:0 and C18:1, which were close to the properties of palm oil. The fuel properties of biodiesel comply with the EN14214:2012 standard. Thus, the vegetable waste can be a good biodiesel feedstock. Three blends (MOB10, MOB20 and MOB30 with 10, 20, and 30% of biodiesel) were tested for engine performance and emission characteristics in a 3.5 kW VCR research engine. At full load, MOB20 reduced the pollutant emissions of CO and HC by 47.8% and 33.2% with the penalty of increased NOx by 3.9%, while BTE reduced by 0.8% with the increased BSFC by 5.2%. Thus, the addition of vegetable waste biodiesel blends reduced the emissions of CO and HC significantly with slight reduction of brake thermal efficiency.

Microbial Lipid Based Biorefinery Concepts: A Review of Status and Prospects

The use of lignocellulosic biomass as a raw material for the production of lipids has gained increasing attention, especially in recent years when the use of food in the production of biofuels has become a current technology. Thus, the competition for raw materials for both uses has brought the need to create technological alternatives to reduce this competition that could generate a reduction in the volume of food offered and a consequent commercial increase in the value of food. Furthermore, the use of microbial oils has been studied in many industrial branches, from the generation of renewable energy to the obtainment of several value-added products in the pharmaceutical and food industries. Thus, this review provides an overview of the feasibility and challenges observed in the production of microbial lipids through the use of lignocellulosic biomass in a biorefinery. Topics covered include biorefining technology, the microbial oil market, oily microorganisms, mechanisms involved in lipid-producing microbial metabolism, strain development, processes, lignocellulosic lipids, technical drawbacks, and lipid recovery.

Optimization of Wheat Straw Conversion into Microbial Lipids by Lipomyces tetrasporus DSM 70314 from Bench to Pilot Scale

Microbial lipids are renewable platforms for several applications including biofuels, green chemicals, and nutraceuticals that can be produced from several residual carbon sources. Lignocellulosic biomasses are abundant raw materials for the production of second-generation sugars with conversion yields depending on the quality of the hydrolysates and the metabolic efficiency of the microorganisms. In the present work, wheat straw pre-treated by steam explosion and enzymatically hydrolysed was converted into microbial lipids by Lipomyces tetrasporus DSM 70314. The preliminary optimization of the enzymatic hydrolysis was performed at the bench scale through the response surface methodology (RSM). The fermentation medium and set-up were optimized in terms of the nitrogen (N) source and carbon-to-nitrogen (C/N) ratio yielding to the selection of soy flour as a N source and C/N ratio of 160. The bench scale settings were scaled-up and further optimized at the 10 L-scale and finally at the 50 L pilot scale bioreactor. Process optimization also included oxygen supply strategies. Under optimized conditions, a lipid concentration of 14.8 gL−1 was achieved corresponding to a 23.1% w/w lipid yield and 67.4% w/w lipid cell content. Oleic acid was the most abundant fatty acid with a percentage of 57%. The overall process mass balance was assessed for the production of biodiesel from wheat straw.

Isolation of Pure Lignin and Highly Digestible Cellulose from Defatted and Steam-Exploded Cynara cardunculus

In this work, a three-step approach to isolate the main components of lignocellulosic cardoon, lignin and cellulose, was investigated. The raw defatted biomass, Cynara cardunculus, after steam explosion was subjected to a mild organosolv treatment to extract soluble lignin (L1). Then, enzymatic hydrolysis was performed to achieve decomposition of the saccharidic portion into monosaccharides and isolate residual lignin (L2). The fractionation conditions were optimized to obtain a lignin as less degraded as possible and to maximize the yield of enzymatic hydrolysis. Furthermore, the effect of the use of aqueous ammonia as an extraction catalyst on both fractions was studied. Each fraction was characterized by advanced techniques, such as elemental analysis and ³¹P nuclear magnetic resonance (NMR), ¹³C-¹H two-dimensional (2D)-NMR, attenuated total reflectance-Fourier transform infrared (ATR-FTIR), and UV-vis spectroscopies for lignin and X-ray diffraction (XRD), Klason compositional analysis, elemental analysis, and ATR-FTIR spectroscopy for cellulose-rich fractions. The impact of the cellulose-rich fraction composition and crystallinity was also correlated to the efficiency of the hydrolysis step, performed using the enzymatic complex Cellic CTec3.

Phosphate limitation as crucial factor to enhance yeast lipid production from short-chain fatty acids

Microbial lipids for chemical synthesis are commonly obtained from sugar-based substrates which in most cases is not economically viable. As a low-cost carbon source, short-chain fatty acids (SCFAs) that can be obtained from food wastes offer an interesting alternative for achieving an affordable lipid production process. In this study, SCFAs were employed to accumulate lipids using Yarrowia lipolytica ACA DC 50109. For this purpose, different amounts of SCFAs, sulfate, phosphate and carbon: phosphate ratios were used in both synthetic and real SCFAs-rich media. Although sulfate limitation did not increase lipid accumulation, phosphate limitation was proved to be an optimal strategy for increasing lipid content and lipid yields in both synthetic and real media, reaching a lipid productivity up to 8.95 g/L h. Remarkably, the highest lipid yield (0.30 g/g) was achieved under phosphate absence condition (0 g/L). This fact demonstrated the suitability of using low-phosphate concentrations to boost lipid production from SCFAs.

Bioconversion of biowaste into renewable energy and resources: A sustainable strategy

Due to its high amount of organic and biodegradable components that can be recycled, biowaste is not only a major cause of environmental contamination, but also a vast store of useful materials. The transformation of biowaste into energy and resources via biorefinery is an unavoidable trend, which could aid in reducing carbon emissions and alleviating the energy crisis in light of dwindling energy supplies and mounting environmental difficulties related with solid waste. In addition, the current pandemic and the difficult worldwide situation, with their effects on the economic, social, and environmental aspects of human life, have offered an opportunity to promote the transition to greener energy and sources. In this context, the current advancements and possible trends of utilizing widely available biowaste to produce key biofuels (such as biogas and biodiesel) and resources (such as organic acid, biodegradable plastic, protein product, biopesticide, bioflocculant, and compost) are studied in this review. To achieve the goal of circular bioeconomy, it is necessary to turn biowaste into high-value energy and resources utilizing biological processes. In addition, the usage of recycling technologies and the incorporation of bioconversion to enhance process performance are analyzed critically. Lastly, this work seeks to reduce a number of enduring obstacles to the recycling of biowaste for future use in the circular economy. Although it could alleviate the global energy issue, additional study, market analysis, and finance are necessary to commercialize alternative products and promote their future use. Utilization of biowaste should incorporate a comprehensive approach and a methodical style of thinking, which can facilitate product enhancement and decision optimization through multidisciplinary integration and data-driven techniques.

Effect of the Combining Corn Steep Liquor and Urea Pre-treatment on Biodegradation and Hydrolysis of Rice Straw

A novel pre-treatment using corn steep liquor (CSL) and urea was developed to enhance the enzymatic saccharification and degradability of rice straw (RS). We used RS (1) without (Con) or with additives of (2) 5% urea (U), (3) 9% CSL and 2.5% urea (CU), and (4) 9% CSL and 5% urea (C5U). The result showed that the water-soluble carbohydrate (WSC) conversion of RS reached 69.32% after C5U pre-treatment. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and X-ray diffraction analysis (XRD) confirmed that the surface of pre-treated RS exposed more cellulose and hemicellulose due to the disruption of the resistant structure of lignocellulose. Pre-treated RS significantly decreased neutral detergent fiber (NDF) and acid detergent fiber (ADF) contents and increased crude protein (CP) content, microbial colonization, and induction of Carnobacterium and Staphylococcus attachment. Altogether, we concluded that pre-treatment of a combination of CSL and urea has the potential to improve the nutritive value of RS.

In-situ transesterification of single-cell oil for biodiesel production: a review

In recent years, biodiesel synthesis and production demands have increased because of its high degradability, cleaner emissions, non-toxicity, and an alternative to petroleum diesel. In this context, Single Cell Oil (SCO) has been identified as an alternative feedstock, having the advantage of accumulating high intracellular lipid. SCO/microbial lipids are potential alternatives for sustainable biodiesel production. The traditional technique for biodiesel production from the oils obtained from microbes generally requires two steps: lipid extraction and transesterification. In-situ transesterification is an innovative and renewable process for biodiesel production. It rules out the need to isolate and refine the feedstock lipid, as it directly uses biomass in a single step, i.e., the pretreated biomass will be subjected to in-situ transesterification in the presence of catalysts. Hence, the production cost can be reduced by eliminating the lipid extraction procedure. The current review focuses on the basic features and advantages of in-situ transesterification of SCO for biodiesel production with the aid of short-chain alcohols along with different acid, base, and enzyme catalysts. In addition, a comparative study was carried out to highlight the merits of in-situ transesterification over conventional transesterification.

Liquid wastes as a renewable feedstock for yeast biodiesel production: Opportunities and challenges

Microbial lipids (bacterial, yeast, or algal) production and its utilization as a feedstock for biodiesel production in a sustainable and economical way along with waste degradation is a promising technology. Oleaginous yeasts have demonstrated multiple advantages over algae and bacteria such as high lipid yields, lipid similarity to vegetable oil, and requirement of lesser area for cultivation. Oleaginous yeasts grown on lignocellulosic solid waste as renewable feedstocks have been widely reported and reviewed. Recently, industrial effluents and other liquid wastes have been evaluated as feedstocks for biodiesel production from oleaginous yeasts. The idea of the utilization of wastewater for the growth of oleaginous yeasts for simultaneous wastewater treatment and lipid production is gaining attention among researchers. However, the detailed knowledge on the economic aspects of different process involved during the conversion of oleaginous yeast into lipids hinders its large-scale application. Therefore, this review aims to provide an overview of yeast-derived biodiesel production by utilizing industrial effluents and other liquid wastes as feedstocks. Various technologies for biomass harvesting, lipid extraction and the economic aspects specifically focused on yeast biodiesel production were also analyzed and reported in this review. The utilization of liquid wastes and the incorporation of cost-efficient harvesting and lipid extraction strategy would facilitate large-scale commercialization of biodiesel production from oleaginous yeasts in near future.

Enhanced biodiesel and β-carotene production in Rhodotorula pacifica INDKK using sugarcane bagasse and molasses by an integrated biorefinery framework

Dependency on fossil fuels raises an economic and ecological concern that has urged to look for alternative sources of energy. Bio-refinery concept is one of the alternate frameworks for the biomass conversion into biofuel and other value-added by-products. The present work illustrates importance of an oleaginous yeast Rhodotorula pacifica INDKK in an integrated bio-refinery field by utilizing renewable sugars generated from lignocellulosic biomass. The maximum 11.8 g/L lipid titer, 210.4 mg/L β-carotene and 7.1 g animal feed were produced by R. pacifica INDKK in bioreactor containing 5% (v/v) molasses supplemented with enzymatically hydrolyzed and alkali-pretreated sugarcane bagasse hydrolysate (35% v/v). Furthermore, xylooligosaccharides (20.6 g/L), a beneficial prebiotics were also produced from the hemicellulosic fraction separated after alkali pretreatment of bagasse. This novel concept of integrated yeast bio-refinery for concomitant production of biodiesel and multiple value-added products with minimum waste generation is proposed as a sustainable and profitable process.

Potential use of industrial by-products as promising feedstock for microbial lipid and lipase production and direct transesterification of wet yeast into biodiesel by lipase and acid catalysts

This work attempted the conversion of crude glycerol to lipid and lipase by Yarrowia lipolytica and the direct transesterification of wet yeast by its lipase into biodiesel via response surface methodology to enhance the cost-effectiveness of biodiesel production from the lipids. The yeast grew better and accumulated a high amount of lipids on the waste combined with fish waste hydrolysate, but only exhibited high lipase activity on the waste supplemented with surfactants (i.e., gum Arabic, Tween 20, Tween 80). However, the combination of both wastes and Tween 80 further improved growth, lipid productivity, and lipase activity. More importantly, lipase-direct transesterification under optimal conditions (wet cell concentration of 17.97 mg-DCW, methanol loading of 8.21 µL, and hexane loading of 10.26 µL) followed by acid-catalyst transesterification (0.4 M H₂SO₄), offered high FAME yields (>90%), showing the efficiency of the process when applied for the industrialization of biodiesel production from microbial lipids.

Enhancing microbial lipids yield for biodiesel production by oleaginous yeast Lipomyces starkeyi fermentation: A review

The enhanced production of microbial lipids suitable for manufacturing biodiesel from oleaginous yeast Lipomyces starkeyi is critically reviewed. Recent advances in several aspects involving the biosynthetic pathways of lipids, current conversion efficiencies using various carbon sources, intensification strategies for improving lipid yield and productivity in L. starkeyi fermentation, and lipid extraction approaches are analyzed from about 100 papers for the past decade. Key findings on strategies are summarized, including (1) optimization of parameters, (2) cascading two-stage systems, (3) metabolic engineering strategies, (4) mutagenesis followed by selection, and (5) co-cultivation of yeast and algae. The current technical limitations are analyzed. Research suggestions like examination of more gene targets via metabolic engineering are proposed. This is the first comprehensive review on the latest technical advances in strategies from the perspective of process and metabolic engineering to further increase the lipid yield and productivity from L. starkeyi fermentation.

Heavy metal impact on lipid production from oleaginous microorganism cultivated with wastewater sludge

Using municipal wastewater sludge to produce microbial lipid is an effective way of resource recycling. Sludge contains heavy metals and may lead to negative impact on lipid production. However, relative study has not been reported. In this study, metal impact on Lipomyces starkeyi lipid accumulation was conducted. Results showed that Cd²⁺ had great impact on lipid accumulation, but other metals had no much impact. The maximum lipid content of L. starkeyi cultivated in 0.55 mg/L of Cd²⁺ was only 41% w/w, which was lower than the control (51% w/w). The inhibition on acetyl-CoA formation was observed when Cd²⁺ was in the medium. After removing metals from sludge, the lipid accumulation was only around half of the one without metal removal. It would be due to that not only the toxic metals in the sludge were removed as well as the metals such as Zn²⁺ which can enhance lipid accumulation.

Cutaneotrichosporon oleaginosus: A Versatile Whole-Cell Biocatalyst for the Production of Single-Cell Oil from Agro-Industrial Wastes

Cutaneotrichosporon oleaginosus is an oleaginous yeast with several favourable qualities: It is fast growing, accumulates high amounts of lipids and has a very broad substrate spectrum. Its resistance to hydrolysis by-products makes it a promising biocatalyst for custom tailored microbial oils. C. oleaginosus can accumulate up to 60 wt.% of its biomass as lipids. This species is able to grow by using several compounds as a substrate, such as acetic acid, biodiesel-derived glycerol, N-acetylglucosamine, lignocellulosic hydrolysates, wastepaper and other agro-industrial wastes. This review is focused on state-of-the-art innovative and sustainable biorefinery schemes involving this promising yeast and second- and third-generation biomasses. Moreover, this review offers a comprehensive and updated summary of process strategies, biomass pretreatments and fermentation conditions for enhancing lipid production by C. oleaginosus as a whole-cell biocatalyst. Finally, an overview of the main industrial applications of single-cell oil is reported together with future perspectives.

Two-Stage Fermentation of Lipomyces starkeyi for Production of Microbial Lipids and Biodiesel

The high operating cost is currently a limitation to industrialize microbial lipids production by the yeast Lipomyces starkeyi. To explore economic fermentation technology, the two-stage fermentation of Lipomyces starkeyi using yeast extract peptone dextrose (YPD) medium, orange peel (OP) hydrolysate medium, and their mixed medium were investigated for seven days by monitoring OD₆₀₀ values, pH values, cell growth status, C/N ratios, total carbon concentration, total nitrogen concentration, residual sugar concentration, lipid content, lipid titer, and fatty acids profiles of lipids. The results showed that two-stage fermentation with YPD and 50% YPD + 50% OP medium contributed to lipid accumulation, leading to larger internal lipid droplets in the yeast cells. However, the cells in pure OP hydrolysate grew abnormally, showing skinny and angular shapes. Compared to the one-stage fermentation, the two-stage fermentation enhanced lipid contents by 18.5%, 27.1%, and 21.4% in the flasks with YPD medium, OP medium, and 50%YPD + 50%OP medium, and enhanced the lipid titer by 77.8%, 13.6%, and 63.0%, respectively. The microbial lipids obtained from both one-stage and two-stage fermentation showed no significant difference in fatty acid compositions, which were mainly dominated by palmitic acid (33.36–38.43%) and oleic acid (46.6–48.12%). Hence, a mixture of commercial medium and lignocellulosic biomass hydrolysate could be a promising option to balance the operating cost and lipid production.

Oleaginous Yeasts as Cell Factories for the Sustainable Production of Microbial Lipids by the Valorization of Agri-Food Wastes

The agri-food industry annually produces huge amounts of crops residues and wastes, the suitable management of these products is important to increase the sustainability of agro-industrial production by optimizing the entire value chain. This is also in line with the driving principles of the circular economy, according to which residues can become feedstocks for novel processes. Oleaginous yeasts represent a versatile tool to produce biobased chemicals and intermediates. They are flexible microbial factories able to grow on different side-stream carbon sources such as those deriving from agri-food wastes, and this characteristic makes them excellent candidates for integrated biorefinery processes through the production of microbial lipids, known as single cell oils (SCOs), for different applications. This review aims to present an extensive overview of research progress on the production and use of oleaginous yeasts and present discussions on the current bottlenecks and perspectives of their exploitation in different sectors, such as foods, biofuels and fine chemicals.

Integrated cascade biorefinery processes for the production of single cell oil by Lipomyces starkeyi from Arundo donax L. hydrolysates

Giant reed (Arundo donax L.) is a promising source of carbohydrates that can be converted into single cell oil (SCO) by oleaginous yeasts. Microbial conversion of both hemicellulose and cellulose fractions represents the key step for increasing the economic sustainability for SCO production. Lipomyces starkeyi DSM 70,296 was cultivated in two xylose-rich hydrolysates, obtained by the microwave-assisted hydrolysis of hemicellulose catalysed by FeCl₃ or Amberlyst-70, and in two glucose-rich hydrolysates obtained by the enzymatic hydrolysis of cellulose. L. starkeyi grew on both undetoxified and partially-detoxified hydrolysates, achieving the lipid content of 30 wt% and yield values in the range 15-24 wt%. For both integrated cascade processes the final production of about 8 g SCO from 100 g biomass was achieved. SCO production through integrated hydrolysis cascade processes represents a promising solution for the effective exploitation of lignocellulosic feedstock from perennial grasses towards new generation biodiesel and other valuable bio-based products.

Microbial lipids from organic wastes: Outlook and challenges

Microbial lipids have recently drawn a lot of attention as renewable sources for biochemicals production. Strong research efforts have been addressed to efficiently use organic wastes as carbon source for microbial lipids, which would definitively increase the profitability of the production process and boost a bio-based economy. This review compiles interesting traits of oleaginous microorganisms and highlights current trends on microbial- and process-oriented approaches to maximize microbial oil production from inexpensive substrates like lignocellulosic sugars, volatile fatty acids and glycerol. Furthermore, downstream processes such as cell harvesting or lipid extraction, that are decisive for the cost-effectiveness of the process, are discussed. To underpin microbial oils within the so demanded circular economy, associated challenges, recent advances and possible industrial applications that are also identified in this review.