Ethanol as an efficient cosubstrate for the biodegradation of azo dyes by Providencia rettgeri: Mechanistic analysis based on kinetics, pathways and genomics

Biodegradation of carbon disulfide and hydrogen sulfide using a moving bed biofilm reactor coupled with sulfur recycling: Performance, mechanism, and potential application

In this work, a moving bed biofilm reactor (MBBR) was equipped for simultaneous biodegradation of CS2 and H2S. MBBR was started up and operated with different inlet concentrations and retention time; results indicated that approximately 81.9% CS2 and 93.9% H2S could be degraded, and the maximum elimination capacities of 209.3 g/(m3·h) and 138.5 g/(m3·h) were achieved for CS2 and H2S, respectively. The biodegradation mechanisms, including mass transfer, kinetics, and electron transfer, were then investigated. The mass transfer fraction and the maximum degradation rate per unit filter volume were calculated for evaluating the characteristics of mass transfer in MBBR. The variations of extracellular polymeric substances secretion, electron transport system activity and ATP enzyme activity showed that MBBR had an excellent performance for waste gas purification. Subsequently, the recovery of sulfur was explored via morphology, crystal structure, and generation kinetics, indicating that a modified Gompertz model could precisely describe the kinetics of sulfur recovery, and the product selectivity of 51.7% was achieved for sulfur. The microbial community analysis suggested that the dominant genera for biodegradation and sulfur recovery were Acidithiobacillus and Mycobacterium. Finally, MBBR system was validated for treatment of actual waste gas; results indicated that maximum elimination capacities of 134.1 g/(m3·h) and 117.1 g/(m3·h) were obtained for CS2 and H2S, respectively, suggesting that MBBR had the potential for application.

Biodegradation characteristics of p-Chloroaniline and the mechanism of co-metabolism with aniline by Pseudomonas sp. CA-1

Co-metabolism is a promising method to optimize the biodegradation of p-Chloroaniline (PCA). In this study, Pseudomonas sp. CA-1 could reduce 76.57 % of PCA (pH = 8, 70 mg/L), and 20 mg/L aniline as the co-substrate improved the degradation efficiency by 12.50 %. Further, the response and co-metabolism mechanism of CA-1 to PCA were elucidated. The results revealed that PCA caused deformation and damage on the surface of CA-1, and the -OH belonging to polysaccharides and proteins offered adsorption sites for the contact between CA-1 and PCA. Subsequently, PCA entered the cell through transporters and was degraded by various oxidoreductases accompanied by deamination, hydroxylation, and ring-cleavage reactions. Thus, the key metabolite 4-chlorocatechol was identified and two PCA degradation pathways were proposed. Besides, aniline further enhanced the antioxidant capacity of CA-1, stimulated the expression of catechol 2,3-dioxygenase and promoted meta-cleavage efficiency of PCA. The findings provide new insights into the treatment of PCA-aniline co-pollution.

Microbial synergies drive simultaneous biodegradation of ethoxy and alkyl chains of Nonylphenol Ethoxylate in fluidized bed reactors

The widely-used surfactant Nonylphenol Ethoxylate (NPEO) produces endocrine-disrupting compounds during biodegradation, with these byproducts being more harmful than untreated NPEO. This study investigates the effectiveness of a Fluidized Bed Reactor (FBR) in reducing the production of 4-Nonylphenol (4-NP) during the biodegradation of NPEO. Two identical FBR filled with sand were used to assess the NPEO degradation and to enhance the microbial consortia capable of breaking down the complex byproducts, ethanol and fumarate were introduced as co-substrates. Our findings demonstrate the significant potential of the FBR, especially when coupled with fumarate, for enhancing the surfactant degradation. It outperforms the efficiency achieved with ethanol as the primary electron donor, albeit with a higher rate of byproduct production. Microbial community taxonomy and metabolic prediction revealed the high abundance of Geobacter (1.51-31.71%) and Methanobacterium (1.08-13.81%) in non-conductive sand. This may hint a new metabolic interaction and expand our understanding of Direct Interspecies Electron Transfer (DIET) in bioreactors applied to micropollutants degradation. Such an intricate relationship between facultative and anaerobes working together to simultaneously biodegrade the ethoxy and alkyl chains presents a new perspective on NPEO degradation and can potentially be extended to other micropollutants.

Pirarucu hydroxyapatite applied to ternary competitive adsorption of synthetic basic dyes as contaminants of emerging concern: kinetic, equilibrium, and ANN studies

This study investigated the single and multicomponent adsorption of three emerging pollutants, the basic dyes Rhodamine 6G (R6G), Auramine-O (AO), and Brilliant Green (BG) by using hydroxyapatite synthesized from Pirarucu scales as adsorbent (HAP). The adsorption process was studied using seven different systems: AO-single, R6G-single, BG-single, R6G + AO, BG + AO, BG + R6G, and R6G + AO + BG. For kinetics, the initial concentration of each adsorbate per system was 50 mg/L, the results showed that the singular adsorption of these dyes was best-represented by the pseudo-second-order model (qAO = 62.54 mg/g, qR6G = 7.91 mg/g, qBG = 62.40 mg/g), however, the multicomponent adsorption was well-fitted by a pseudo-first-order model (ternary system: qAO = 56.21 mg/g, qR6G = 14.95 mg/g, qBG = 60.62 mg/g). For equilibrium, the initial concentration of each adsorbate per system was 10-300 mg/L, and the single adsorption systems were best represented by the Langmuir model. Nonetheless, the results displayed in the multicomponent mixture showed the presence of inflection points of AO and R6G whenever BG was present in solution with C0 > 150 mg/L, thus indicating that BG has greater affinity with HAP. The presence of inflection points in the curves represented a limitation for applying traditional equilibrium models, thus, an artificial neural network (ANN) was applied to non-linear curve fit this process and satisfactorily predicted the kinetics and equilibrium data. Finally, the analysis of thermodynamics for the ternary mixture revealed that the adsorption process is spontaneous (ΔG < 0), endothermic (ΔH > 0), and increases to a disorganized state as the temperature rises (ΔS > 0).

Recent Strategies for the Remediation of Textile Dyes from Wastewater: A Systematic Review

The presence of dye in wastewater causes substantial threats to the environment, and has negative impacts not only on human health but also on the health of other organisms that are part of the ecosystem. Because of the increase in textile manufacturing, the inhabitants of the area, along with other species, are subjected to the potentially hazardous consequences of wastewater discharge from textile and industrial manufacturing. Different types of dyes emanating from textile wastewater have adverse effects on the aquatic environment. Various methods including physical, chemical, and biological strategies are applied in order to reduce the amount of dye pollution in the environment. The development of economical, ecologically acceptable, and efficient strategies for treating dye-containing wastewater is necessary. It has been shown that microbial communities have significant potential for the remediation of hazardous dyes in an environmentally friendly manner. In order to improve the efficacy of dye remediation, numerous cutting-edge strategies, including those based on nanotechnology, microbial biosorbents, bioreactor technology, microbial fuel cells, and genetic engineering, have been utilized. This article addresses the latest developments in physical, chemical, eco-friendly biological and advanced strategies for the efficient mitigation of dye pollution in the environment, along with the related challenges.

In Situ Synthesis of 3D BiOCl-Graphene Aerogel and Synergistic Effect by Photo-Assisted Activation of Persulfate for Methyl Orange Degradation

BiOCl/graphene aerogel graphene (BGA) was successfully obtained by in situ hydrothermal synthesis, and the chemical, structural, morphological, and photocatalytic properties were systematically characterized. BGA with the doping amount of BiOCl at 20% (BGA-4) exhibited the optimal activation efficiency for persulfate (PDS) on the degradation of methyl orange (MO) under simulated sunlight (SSL) illumination as compared to the pure graphene (GA) and aerogel composites with different BiOCl content. The influence of various reaction parameters on the MO removal efficiency, such as the reaction system, catalyst activator dose, PDS concentration, BiOCl doping amount, and the initial pH of the solution, was investigated. Under optimum conditions, the catalytic efficiency of BiOCl-doped GA with the mass ratio of 20% (BGA-4) was 5.61 times that of GA. The strengthening effect of BGA-4 benefited from the synergistic effect of ¹O₂, O₂·^- and the generation and rapid electron transfer of photo-induced electron (e^-) in the BGA-4/SSL/PDS system. Considering the superior stability and recyclability of BGA-4, the BGA-4/SSL/PDS system exhibits great potential in actual wastewater treatment.

Fe, N, S co-doped cellulose paper carbon fibers as an air-cathode catalyst for microbial fuel cells

The heteroatoms and transition metal co-doped carbon-based catalysts are an important way to improve the catalytic activity of oxygen reduction reaction (ORR). Herein, we reported a facile method to obtain iron, nitrogen, and sulfur co-doped cellulose paper carbon fibers as catalysts (Fe-N-S/CFs) for ORR in microbial fuel cells (MFCs) with the adsorption recovery of Congo red molecules from dye wastewater. The thermal treatment promoted the etching of carbon surface by ferric ions, resulting in increased surface roughness for forming the defective carbon structure. The rich active species and defective carbon formed on the etched surface to enhance the electroactive surface area and effective sites. Fe-N-S/CFs catalysts achieved high half-wave potential due to the synergy effect between chemical components and defect structures. The assembled single-chamber air cathode MFC gained a high maximum power density of 1773 ± 40 mW m^-2 versus Pt/C MFC of 1325 ± 94 mW m^-2. This work provides a strategy for recovering dye molecules from wastewater to prepare non-precious metal catalysts for enhancing ORR activity.

Effect of salinity on removal performance of anaerobic membrane bioreactor treating azo dye wastewater

Membrane bioreactor (MBR) is an attractive option method for treating azo dye wastewater under extreme conditions. The present study assessed the effect of salinity on the performance of anaerobic MBR in treating azo dye wastewater. Increased salinity showed adverse effects on the decolorization efficiency and chemical oxygen demand (COD) removal efficiency. The decolorization efficiency decreased from 95.8% to 82.3% and 73.1% with a stepwise increasing of salinity from 0 to 3% and 5%, respectively. The COD removal efficiency decreased from 80.7% to 71.3% when the salinity increased from 0 to 3% and then decreased to 58.6% at 5% salinity. The volatile fatty acids (VFAs) concentration also increased as the salinity increased. Furthermore, increased salinity led to the elevated production of soluble microbial products (SMP) and extracellular polymeric substances (EPS), which can provide a protective barrier against harsh environments. More serious membrane fouling was observed as the SMP and EPS concentrations increased. The concentration of loosely bound EPS (LB-EPS), tightly bound EPS (TB-EPS), and the polysaccharide/protein (PS/PN) ratios in LB-EPS and TB-EPS all increased when the salinity was elevated. The production of SMP and EPS was caused by the generation of PS in response to the saline environment. Lactobacillus, Lactococcus, Anaerosporobacter, and Pectinatus were the dominant bacteria, and Lactobacillus and Lactococcus were the decolorization bacteria in the MBR. The lack of halophilic bacteria was the main reason for the decreased decolorization efficiency in the salinity environment.

The capability of chloramphenicol biotransformation of Klebsiella sp. YB1 under cadmium stress and its genome analysis

Co-contamination by antibiotics and heavy metal is common in the environment, however, there is scarce information about antibiotics biodegradation under heavy metals stress. In this study, Klebsiella sp. Strain YB1 was isolated which is capable of biodegrading chloramphenicol (CAP) with a biodegradation efficiency of 22.41% at an initial CAP of 10 mg L^-1 within 2 days. CAP biodegradation which fitted well with the first-order kinetics. YB1 still degrades CAP under Cd stress, however 10 mg L^-1 Cd inhibited CAP biodegradation by 15.1%. Biotransformation pathways remained the same under Cd stress, but two new products (Cmpd 19 and Cmpd 20) were identified. Five parallel metabolism pathways of CAP were proposed with/without Cd stress, including one novel pathway (pathway 5) that has not been reported before. In pathway 5, the initial reaction was oxidation of CAP by disruption of C-C bond at the side chain of C1 and C2 with the formation of 4-nitrobenzyl alcohol and CY7, then these intermediates were oxidized into p-nitrobenzoic acid and CY1, respectively. CAP acetyltransferase and nitroreductase and 2,3/4,5-dioxygenase may play an important role in CAP biodegradation through genome analysis and prediction. This study deepens our understanding of mechanism of antibiotic degradation under heavy metal stress in the environment.

Easily biodegradable substrates are crucial for enhancing antibiotic risk reduction: Low-carbon discharging policies need to be more specified

Governments have formulated stricter wastewater treatment plant (WWTP) discharge standards to address water pollution; however, with the cost of aggravating the refractory of the discharges. These policies are not in line with the classic co-metabolism theory; thus, we evaluated the effects of an easily biodegradable substrate on the removal efficiency of antibiotics and antibiotic resistance genes (ARGs) in the receiving water. In this study, reactor with 8 d of hydraulic retention time (HRT) was constructed to simulate a receiving river, and several antibiotics (0.30 mg/L each) were continuously discharged to the reactor (tetracycline, ciprofloxacin, amoxicillin, chloramphenicol, and sulfamethoxazole). Sodium acetate (NaAc) was used as a representative easily biodegradable substrate, and treatment protocols with and without a co-substrate were compared. The attenuation of the antibiotics in the simulated river and the production and dissemination of ARGs were analyzed. The results showed that 50 mg/L NaAc activated non-specific enzymes (a log2-fold change of 3.1-8.8 compared with 0 mg/L NaAc). The removal rate of the antibiotics was increased by 4-32%, and the toxicity of the downstream water was reduced by 35%. The upregulation of antioxidant enzymes caused the intracellular reactive oxygen species (ROSs) decreased by up to 47%, inhibiting horizontal gene transfer and reducing mobile genetic element-mediated ARGs (mARGs) by 18-56%. Furthermore, NaAc also increased the alpha diversity of the microbial community by 5-15% (Shannon-Wiener Index) and reduced the abundance of human bacterial pathogens by 22-36%. In summary, easily biodegradable substrates in the receiving water are crucial for reducing antibiotic risk.

Enhanced adsorption of rhodamine B from water by Fe-N co-modified biochar: Preparation, performance, mechanism and reusability

To adsorb rhodamine B (RhB) in wastewater by pristine biochar was limited, while the modified biochar has shown great potential adsorption performance. Here, coconut shell mixed with FeSO₄·7H₂O and urea was prepared to synthesize Fe-N co-modified biochar by once pyrolysis method at 500℃. The results showed Fe-N-BC had larger surface area (972.8714 m²·g^-1), higher developed porous structure (0.65016 cm³·g^-1), and more oxygen-containing groups, which collectively contributed to significantly improve the adsorption performance of the Fe-N-BC towards RhB. The maximum adsorption capacity of RhB reached 12.41 mg·g^-1 by Fe-N-BC which was 1.58, 1.43 and 1.26 folds than that of BC, N-BC and Fe-BC, respectively. The mechanism of adsorption for Fe-N-BC towards RhB including ion exchange, pore filling, surface complexation, H-bond and π-π interaction. This study indicates that Fe-N-BC is an excellent adsorbent for RhB removal from wastewater.

Recent advances in the biodegradation of azo dyes

As dye demand continues to rapidly increase in the food, pharmaceutical, cosmetic, paper, textile, and leather industries, an industrialization increase is occurring. Meanwhile, the degradation and removal of azo dyes have raised broad concern regarding the hazards posed by these dyes to the ecological environment and human health. Physicochemical treatments have been applied but are hindered by high energy and economic costs, high sludge production, and chemicals handling. Comparatively, the bioremediation technique is an eco-friendly, removal-efficient, and cost-competitive method to resolve the problem. This paper provides scientific and technical information about recent advances in the biodegradation of azo dyes. It expands the biodegradation efficiency, characteristics, and mechanisms of various microorganisms containing bacteria, fungi, microalgae, and microbial consortia, which have been reported to biodegrade azo dyes. In addition, information about physicochemical factors affecting dye biodegradation has been compiled. Furthermore, this paper also sketches the recent development and characteristics of advanced bioreactors.

Recent Achievements in Dyes Removal Focused on Advanced Oxidation Processes Integrated with Biological Methods

In the last 3 years alone, over 10,000 publications have appeared on the topic of dye removal, including over 300 reviews. Thus, the topic is very relevant, although there are few articles on the practical applications on an industrial scale of the results obtained in research laboratories. Therefore, in this review, we focus on advanced oxidation methods integrated with biological methods, widely recognized as highly efficient treatments for recalcitrant wastewater, that have the best chance of industrial application. It is extremely important to know all the phenomena and mechanisms that occur during the process of removing dyestuffs and the products of their degradation from wastewater to prevent their penetration into drinking water sources. Therefore, particular attention is paid to understanding the mechanisms of both chemical and biological degradation of dyes, and the kinetics of these processes, which are important from a design point of view, as well as the performance and implementation of these operations on a larger scale.