A comprehensive review on the biological conversion of lignocellulosic biomass into hydrogen: Pretreatment strategy, technology advances and perspectives

Strategies for the incorporation of organosolv lignin in hydroxypropyl methylcellulose-based films: A comparative study

Organosolv lignin extracted from vine pruning residues was added to hydroxypropyl methylcellulose (HPMC)-based films using three strategies: i) lignin incorporated into the film (lignin-based film), ii) lignin nanoparticles (LNPs) incorporated into the film (LNPs-based film), and iii) lignin coated on HPMC films' surface (lignin-coated film). The films obtained were evaluated in terms of morphology, water barrier and mechanical properties, and antioxidant capacity. Results showed that LNPs incorporation did not affect the films´ water vapour permeability (WVP). Nonetheless, the lignin-based and lignin-coated films improved the water barrier properties of HPMC-based films, achieving a 31.5 and 36 % reduction of WVP, respectively. The morphological evaluation, performed by scanning electron microscopy, revealed films' morphology changes with the lignin incorporation, which was more evident in the lignin-based films. Fourier transform infrared spectroscopy (FTIR) showed minor changes in the film's structure using the different lignin incorporation methods. The mechanical properties were improved, including a significant increase in the tensile strength in the lignin-based and lignin-coated films. All films showed high radical scavenging activity (RSA) after 24 h, with a gradual increase in the lignin-coated films over time. The lignin-coated films showed to be the most promising incorporation strategy to improve the HPMC-based film's properties.

1-Ethyl-3-methylimidazolium acetate pretreatment for maximizing reducing sugar recovery from mixed cabbage residue

Vegetable waste, including mixed cabbage residue (MCR), is considered a promising raw material for bioenergy production because of its high lignocellulosic component. In this study, the pretreatment of MCR by ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) was optimized based on response surface methodology. The optimal condition for MCR pretreatment was determined at 55.8 °C, with a reaction of 2.65 h and liquid-solid ratio of 4.60:1 v/w. Hydrolysis of pretreated MCR from optimal pretreatment conditions generated a maximum glucose yield of 156.65 ± 7.66 mg/g MCR. Untreated and pretreated MCRs were successfully characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The pretreated MCR exhibited increased clear pores and incomplete structure. Moreover, compared with untreated biomass, decreased lignin, decreased hemicellulose, increased surface area, and cellulose crystallinity were observed. Thus, [Emim][OAc] pretreatment is a promising alternative approach for higher glucose production from MCR.

Optimization of biogas production from straw wastes by different pretreatments: Progress, challenges, and prospects

Lignocellulosic biomass (LCB) presents a promising feedstock for carbon management due to enormous potential for achieving carbon neutrality and delivering substantial environmental and economic benefit. Bioenergy derived from LCB accounts for about 10.3 % of the global total energy supply. The generation of bioenergy through anaerobic digestion (AD) in combination with carbon capture and storage, particularly for methane production, provides a cost-effective solution to mitigate greenhouse gas emissions, while concurrently facilitating bioenergy production and the recovery of high-value products during LCB conversion. However, the inherent recalcitrant polymer crystal structure of lignocellulose impedes the accessibility of anaerobic bacteria, necessitating lignocellulosic residue pretreatment before AD or microbial chain elongation. This paper seeks to explore recent advances in pretreatment methods for LCB biogas production, including pulsed electric field (PEF), electron beam irradiation (EBI), freezing-thawing pretreatment, microaerobic pretreatment, and nanomaterials-based pretreatment, and provide a comprehensive overview of the performance, benefits, and drawbacks of the traditional and improved treatment methods. In particular, physical-chemical pretreatment emerges as a flexible and effective option for methane production from straw wastes. The burgeoning field of nanomaterials has provoked progress in the development of artificial enzyme mimetics and enzyme immobilization techniques, compensating for the intrinsic defect of natural enzyme. However, various complex factors, such as economic effectiveness, environmental impact, and operational feasibility, influence the implementation of LCB pretreatment processes. Techno-economic analysis (TEA), life cycle assessment (LCA), and artificial intelligence technologies provide efficient means for evaluating and selecting pretreatment methods. This paper addresses current issues and development priorities for the achievement of the appropriate and sustainable utilization of LCB in light of evolving economic and environmentally friendly social development demands, thereby providing theoretical basis and technical guidance for improving LCB biogas production of AD systems.

Exploitation of lignocellulosic-based biomass biorefinery: A critical review of renewable bioresource, sustainability and economic views

Urbanization has driven the demand for fossil fuels, however, the overly exploited resource has caused severe damage on environmental pollution. Biorefining using abundant lignocellulosic biomass is an emerging strategy to replace traditional fossil fuels. Value-added lignin biomass reduces the waste pollution in the environment and provides a green path of conversion to obtain renewable resources. The technology is designed to produce biofuels, biomaterials and value-added products from lignocellulosic biomass. In the biorefinery process, the pretreatment step is required to reduce the recalcitrant structure of lignocellulose biomass and improve the enzymatic digestion. There is still a gap in the full and deep understanding of the biorefinery process including the pretreatment process, thus it is necessary to provide optimized and adapted biorefinery solutions to cope with the conversion process in different biorefineries to further provide efficiency in industrial applications. Current research progress on value-added applications of lignocellulosic biomass still stagnates at the biofuel phase, and there is a lack of comprehensive discussion of emerging potential applications. This review article explores the advantages, disadvantages and properties of pretreatment methods including physical, chemical, physico-chemical and biological pretreatment methods. Value-added bioproducts produced from lignocellulosic biomass were comprehensively evaluated in terms of encompassing biochemical products , cosmetics, pharmaceuticals, potent functional materials from cellulose and lignin, waste management alternatives, multifunctional carbon materials and eco-friendly products. This review article critically identifies research-related to sustainability of lignocellulosic biomass to promote the development of green chemistry and to facilitate the refinement of high-value, environmentally-friendly materials. In addition, to align commercialized practice of lignocellulosic biomass application towards the 21st century, this paper provides a comprehensive analysis of lignocellulosic biomass biorefining and the utilization of biorefinery green technologies is further analyzed as being considered sustainable, including having potential benefits in terms of environmental, economic and social impacts. This facilitates sustainability options for biorefinery processes by providing policy makers with intuitive evaluation and guidance.

Effects of cold isostatic press pretreatment of rice straw on microstructure and efficiency of anaerobic digestion for methane production

In this study, rice straw was pretreated using by cold isostatic pressure to disrupt its microstructure and improve the performance of anaerobic digestion, and the optimal process parameters were optimized using the response surface methodology. The results showed that cold isostatic pressure pretreatment under optimal conditions (pressure of 400 MPa and holding time of 9 min) was effective in disrupting the structure of rice straw and improving its biodegradability. The cumulative methane production of the cold isostatic pressure pretreatment group increased by 76% compared to the untreated group. In addition, microbial community analysis showed that the relative abundance of Firmicutes, Halobacterota, DMER64 and Methanosaeta was higher in groups pretreated with cold isostatic pressure than in untreated groups. This study demonstrated the potential of pretreatment of rice straw with cold isostatic pressure to increase methane production during anaerobic digestion.

Highly efficient and durable syngas production over one-step synthesized synergistic oxygen carriers in biomass chemical looping gasification

Biomass chemical looping gasification (BCLG) gives a promising platform for cost-effective and low-polluting syngas production. To overcome the cumbersome process and poor dispersion of two-step synthesized synergistic oxygen carriers (OCs), NiO-LaFeO3 synergistic OCs were synthesized in one-step by sol-gel method with the found best Ni introduction amount of 0.5. The high lattice oxygen mobility and powerful oxidation capacity derived from the Ni-Fe synergistic effect made it perform better in the BCLG reaction. Due to the extraordinary stability of crystalline phase and oxygen activity, its reactivity did not suffer from any degradation during the 50 long-time redox cycles over 2750 min under the optimal working conditions of the ex-situ configuration, mutual mode and steam/biomass mass ratio of 5.0. The gas yield, carbon conversion, syngas selectivity and H2/CO ratio were constantly maintained around 1846.45 mL/g, 86.74%, 79.96% and 2.0, respectively. This study provides a feasible technical route for highly efficient and durable syngas production.

Analytical Pyrolysis of Pinus radiata and Eucalyptus globulus: Effects of Microwave Pretreatment on Pyrolytic Vapours Composition

Pinus radiata (PR) and Eucalyptus globulus (EG) are the most planted species in Chile. This research aims to evaluate the pyrolysis behaviour of PR and EG from the Bío Bío region in Chile. Biomass samples were subjected to microwave pretreatment considering power (259, 462, 595, and 700 W) and time (1, 2, 3, and 5 min). The maximum temperature reached was 147.69 °C for PR and 130.71 °C for EG in the 700 W-5 min condition, which caused the rearrangement of the cellulose crystalline chains through vibration and an increase in the internal energy of the biomass and the decomposition of lignin due to reaching its glass transition temperature. Thermogravimetric analysis revealed an activation energy (Ea) reduction from 201.71 to 174.91 kJ·mol-1 in PR and from 174.80 to 158.51 kJ·mol-1 in EG, compared to the untreated condition (WOT) for the 700 W-5 min condition, which indicates that microwave pretreatment improves the activity of the components and the decomposition of structural compounds for subsequent pyrolysis. Functional groups were identified by Fourier transform infrared spectroscopy (FTIR). A decrease in oxygenated compounds such as acids (from 21.97 to 17.34% w·w-1 and from 27.72 to 24.13% w·w-1) and phenols (from 34.41 to 31.95% w·w-1 and from 21.73 to 20.24% w·w-1) in PR and EG, respectively, was observed in comparison to the WOT for the 700 W-5 min condition, after analytical pyrolysis. Such results demonstrate the positive influence of the pretreatment on the reduction in oxygenated compounds obtained from biomass pyrolysis.

Biorefinery of vineyard winter prunings for production of microbial lipids by the oleaginous yeast Cryptococcus curvatus

Spent biomass from agricultural and forestry industries are substantial low-cost carbon source for reducing the input of microbial lipid production. Herein, the components of the vineyard winter prunings (VWPs) from 40 grape cultivars were analyzed. The VWPs contained (w/w) cellulose ranged from 24.8% to 32.4%, hemicellulose 9.6% to 13.8%, lignin 23.7% to 32.4%. The VWPs from Cabernet Sauvignon was processed with the alkali-methanol pretreatment, and 95.8% of the sugars was released from the regenerated VWPs after enzymatic hydrolysis. The hydrolysates from the regenerated VWPs was suitable for lipid production without further treatment as a lipid content of 59% could be achieved with Cryptococcus curvatus. The regenerated VWPs was also used for lipid production via simultaneous saccharification and fermentation (SSF), which led to a lipid yield of 0.088 g/g raw VWPs, 0.126 g/g regenerated VWPs and 0.185 g/g from the reducing sugars. This work demonstrated that the VWPs can be explored for co-production of microbial lipids.

Research Progress and Trends on Utilization of Lignocellulosic Residues as Supports for Enzyme Immobilization via Advanced Bibliometric Analysis

Lignocellulosic biomasses are used in several applications, such as energy production, materials, and biofuels. These applications result in increased consumption and waste generation of these materials. However, alternative uses are being developed to solve the problem of waste generated in the industry. Thus, research is carried out to ensure the use of these biomasses as enzymatic support. These surveys can be accompanied using the advanced bibliometric analysis tool that can help determine the biomasses used and other perspectives on the subject. With this, the present work aims to carry out an advanced bibliometric analysis approaching the main studies related to the use of lignocellulosic biomass as an enzymatic support. This study will be carried out by highlighting the main countries/regions that carry out productions, research areas that involve the theme, and future trends in these areas. It was observed that there is a cooperation between China, USA, and India, where China holds 28.07% of publications in this area, being the country with the greatest impact in the area. Finally, it is possible to define that the use of these new supports is a trend in the field of biotechnology.

Nature-inspired pretreatment of lignocellulose - Perspective and development

As sustainability gains increasing importance in addition to cost-effectiveness as a criterion for evaluating engineering systems and practices, biological processes for lignocellulose pretreatment have attracted growing attention. Biological systems such as white and brown rot fungi and wood-consuming insects offer fascinating examples of processes and systems built by nature to effectively deconstruct plant cell walls under environmentally benign and energy-conservative environments. Research in the last decade has resulted in new knowledge that advanced the understanding of these systems, provided additional insights into these systems' functional mechanisms, and demonstrated various applications of these processes. The new knowledge and insights enable the adoption of a nature-inspired strategy aiming at developing technologies that are informed by the biological systems but superior to them by overcoming the inherent weakness of the natural systems. This review discusses the nature-inspired perspective and summarizes related advancements, including the evolution from biological systems to nature-inspired processes, the features of biological pretreatment mechanisms, the development of nature-inspired pretreatment processes, and future perspective. This work aims to highlight a different strategy in the research and development of novel lignocellulose pretreatment processes and offer some food for thought.

Syngas production and gas-N evolution over heterogeneously doped La-Fe-O perovskite-type oxygen carriers in chemical looping gasification of microalgae

Chemical looping gasification (CLG) is a promising technology for syngas production with low pollutant emission. In this study, doped La-Fe-O perovskites including LaFeO₃ (LF), LaFe_0.5Ni_0.5O₃ (LN5F5) and La_0.3Ba_0.7FeO₃ (L3B7F) were developed for microalgae CLG. The as-prepared perovskites exhibited an outstanding performance in syngas production with accumulative syngas yield > 33 mol/kg. For gas-N evolution, perovskites were beneficial to the formation of NH₃ and HCN, while the iron ore may convert precursors to NO. Below 400 °C, NO_x can be stored on the perovskite surface in the form of nitrite/nitrate species. When the temperature was above 700 °C, NO_x can be selectively reduced by reducing components in tar or syngas under the catalysis of L3B7F, resulting in the final reduction of NO_x emission. Thus, CLG over L3B7F may be a promising way for efficient utilization of microalgae to overcome the intractable nitrogen-related obstacles in the commercial application of biomass gasification technologies.

Ultrasonic Disintegration to Improve Anaerobic Digestion of Microalgae with Hard Cell Walls-Scenedesmus sp. and Pinnularia sp

Microalgae are considered to be very promising feedstocks for biomethane production. It has been shown that the structure of microalgal cell walls can be highly detrimental to the anaerobic digestibility of biomass. Therefore, there is a real need to seek ways to eliminate this problem. The aim of the present study was to assess the effect of ultrasonic disintegration of Scenedesmus sp. and Pinnularia sp. microalgal biomass on the performance and energy efficiency of anaerobic digestion. The pretreatment was successful in significantly increasing dissolved COD and TOC in the system. The highest CH₄ yields were noted for Scenedesmus sp. sonicated for 150 s and 200 s, which produced 309 ± 13 cm³/gVS and 313 ± 15 cm³/gVS, respectively. The 50 s group performed the best in terms of net energy efficiency at 1.909 ± 0.20 Wh/gVS. Considerably poorer performance was noted for Pinnularia sp., with biomass yields and net energy gains peaking at CH₄ 250 ± 21 cm³/gVS and 0.943 ± 0.22 Wh/gVS, respectively. Notably, the latter value was inferior to even the non-pretreated biomass (which generated 1.394 ± 0.19 Wh/gVS).