High-throughput SPR sensor for food safety

Design and Simulation of High-Performance D-Type Dual-Mode PCF-SPR Refractive Index Sensor Coated with Au-TiO2 Layer

A novel surface plasmon resonance (SPR) refractive index (RI) sensor based on the D-type dual-mode photonic crystal fiber (PCF) is proposed. The sensor employs a side-polished few-mode PCF that facilitates the transmission of the fundamental and second-order modes, with an integrated microfluidic channel positioned directly above the fiber core. This design minimizes the distance to the analyte and maximizes the interaction between the optical field and the analyte, thereby enhancing the SPR effect and resonance loss for improved sensing performance. Au-TiO2 dual-layer material was coated on the surface of a microfluidic channel to enhance the penetration depth of the core evanescent field and tune the resonance wavelength to the near-infrared band, meeting the special needs of chemical and biomedical detection fields. The finite element method was utilized to systematically investigate the coupling characteristics between various modes and surface plasmon polariton (SPP) modes, as well as the impact of structural parameters on the sensor performance. The results indicate that the LP11b_y mode exhibits greater wavelength sensitivity than the HE11_y mode, with a maximum sensitivity of 33,000 nm/RIU and an average sensitivity of 8272.7 nm/RIU in the RI sensing range of 1.25-1.36, which is higher than the maximum sensitivity of 16,000 nm/RIU and average sensitivity of 5666.7 nm/RIU for the HE11b_y mode. It is believed that the proposed PCF-SPR sensor features both high sensitivity and high resolution, which will become a critical device for wide RI detection in mid-infrared fields.

Guided wave resonance-based digital holographic microscopy for high-sensitivity monitoring of the refractive index

Surface plasmon resonance holographic microscopy (SPRHM) has been employed to measure the refractive index but whose performance is generally limited by the metallic intrinsic loss. Herein we first, to our knowledge, utilize guided wave resonance (GWR) with low loss to realize the monitoring of the refractive index by integrating with digital holographic microscopy (DHM). By depositing a dielectric layer on a silver film, we observe a typical GWR in the dielectric layer with stronger field enhancement and higher sensitivity to the surrounding refractive index compared to the silver film-supported SPR, which agrees well with calculations. The innovative combination of the GWR and DHM contributes to the highly sensitive dynamic monitoring of the surrounding refractive index variation. Through the measurement with DHM, we found that the GWR presents an excellent sensitivity, which is 2.6 times higher than that of the SPR on the silver film. The results will pave a new pathway for digital holographic interferometry and its applications in environmental and biological detections.

Advancing Sensitivity in Guided-Wave Surface Plasmon Resonance Sensor through Integration of 2D BlueP/MoS2 Hybrid Layers

The surface plasmon resonance (SPR) signal, generated from the Kretschmann configuration, has been developed as an effective detection technology in chemical and biological sensors. The sensitivity of SPR signals to changes in the surrounding media makes it a valuable tool, as even a slight variation in refractive index can cause a significant change in SPR signals, such as phase, intensity, and resonance angle. However, the detection of ultralow changes in refractive index, which occur in chemical reactions or biological actions, remains a challenge for conventional SPR sensors due to their limited sensitivity. To overcome this limitation, we theoretically propose a novel guided-wave SPR (GWSPR) configuration coated with a few-layer blue phosphorene (blueP)/MoS2 hybrid structure. This configuration aims to enhance the electric field and subsequently achieve a significant improvement in sensitivity. The results of our study demonstrate that the proposed blueP/MoS2-based GWSPR sensor exhibits a high sensitivity of 290°/RIU, which represents an impressive enhancement of approximately 82.4% compared to the conventional Au-based SPR sensor. This advancement addresses the challenge of detecting ultralow changes in refractive index and offers significant potential for enhancing the performance of chemical and biological sensors.

Magnetically Controlled and Addressable Photoelectrochemical Sensor Array with Self-Calibration for the Label-Free Detection of Amyloid β-Proteins

A label-free addressable photoelectric immunosensor array was designed for the detection of amyloid β-proteins based on magnetic separation and self-calibration strategies. In this paper, Na2Ti6O13 with a flower-like morphology was prepared by the hydrothermal method; after continuously combining Fe3O4 and CdS, it was endowed with magnetism and better photoelectric activity. Subsequently, a series of reactions occurred in the solution, and the magnetic separation method was used to enrich the target. On the other hand, the ITO glass was separated into eight sites (2 × 4) using magnets, and a light shield was utilized to prevent light exposure, resulting in addressable and continuous detection. After the uniform preparation of magnetic photoelectric materials and precise control of testing conditions, the relative errors among different sites have been effectively reduced. Moreover, incorporating a self-calibration strategy has allowed the sensor array to achieve greater accuracy. The proposed photoelectrochemical biosensor exhibits a good relationship with amyloid β-protein ranging from 0.01 to 100 ng mL-1 with a limit of detection of 1.1 pg mL-1 and exhibits excellent specificity, reproducibility, and stability.

Highly Localized Surface Plasmon Nanolasers via Strong Coupling

Surface plasmons have robust and strong confinement to the light field which is beneficial for the light-matter interaction. Surface plasmon amplification by stimulated emission of radiation (SPACER) has the potential to be integrated on the semiconductor chip as a compact coherent light source, which can play an important role in further extension of Moore's law. In this study, we demonstrate the localized surface plasmon lasing at room temperature in the communication band using metallic nanoholes as the plasmonic nanocavity and InP nanowires as the gain medium. Optimizing laser performance has been demonstrated by coupling between two metallic nanoholes which adds another degree of freedom for manipulating the lasing properties. Our plasmonic nanolasers exhibit lower power consumption, smaller mode volumes, and higher spontaneous emission coupling factors due to enhanced light-matter interactions, which are very promising in the applications of high-density sensing and photonic integrated circuits.

Spectrometer-based wavelength interrogation SPR imaging via Hadamard transform

We present spectrometer-based wavelength interrogation surface plasmon resonance imaging (SPRi) without mechanical scanning. A polarized broadband light source illuminates an object via a gold-coated prism; the reflected light is spatially modulated by a digital mirror device (DMD) and then measured with a spectrometer. Reflectance spectral images are reconstructed via the Hadamard transform (HT), and a refractive index (RI) map is visualized from the reflectance spectral images by analyzing the resonance peak shift of the spectrum at each image pixel. We demonstrate the feasibility of our method by evaluating the resolution, sensitivity, and dynamic detection range, experimentally obtained as ∼2.203 × 10^-6 RI unit (RIU), ∼3,407 nm/RIU, and ∼0.1403 RIU, respectively. Furthermore, simulations are performed to validate the experimental results.

Characterization of Small Molecule-Protein Interactions Using SPR Method

Surface plasmon resonance (SPR) is an optical phenomenon being used to monitor molecular binding events. With the advantages of being label-free, real-time, and sensitive, SPR assays have become one of the most commonly used techniques to measure binding kinetics, affinity, specificity, and concentration of molecular interactions. In an SPR experiment to measure small molecule-protein interactions, the protein is immobilized on the biosensor surface, while the small molecule flows through the surface of the sensor chip. The interactions between the small molecules and proteins are monitored by subsequent changes in the refractive index and quantified with resonance units. In this chapter, we have utilized an SPR assay to study the interaction of flavonoids and the glucose-regulated protein 78. Assay steps are detailed for immobilization optimization, SPR instrument setup, operation, sample injection, and affinity data analysis.

Data Processing of SPR Curve Data to Maximize the Extraction of Changes in Electrochemical SPR Measurements

We developed a novel measuring and data-processing method for performing electrochemical surface plasmon resonance (EC-SPR) on sensor surfaces for which detecting a specific SPR angle is difficult, such as a polymer having a non-uniform thickness with coloration. SPR measurements are used in medicine and basic research as an analytical method capable of molecular detection without labeling. However, SPR is not good for detecting small molecules with small refractive index changes. The proposed EC-SPR, which combines SPR measurements with an electrochemical reaction, makes it possible to measure small molecules without increasing the number of measurement steps. A drawback of EC-SPR is that it is difficult to detect a specific SPR angle on electron mediators, and it was found that it may not be possible to capture all the features produced. The novel method we describe here is different from the conventional one in which a specific SPR angle is obtained from an SPR curve; rather, it processes the SPR curve itself and can efficiently aggregate the feature displacements in the SPR curves that are dispersed through multiple angles. As an application, we used our method to detect small concentrations of H₂O₂ (LOD 0.7 μM) and glutamate (LOD 5 μM).

Sensitive Oligonucleotide Detection Using Resonant Coupling between Fano Resonance and Image Dipoles of Gold Nanoparticles

The surface plasmon resonance (SPR)-based sensor has been widely used for biodetection. One of the attractive roles is the gold nanostructure with Fano resonance. Its sharp resonant profile takes advantage of the high figure of merit (FoM) in high-sensitivity detection. However, it is still difficult to detect small molecules at low concentrations due to the extremely low refractive index changes on the metallic surface. We propose using the coupling of image dipoles of gold nanoparticles (AuNPs) and Fano resonance of periodic capped gold nanoslits (CGNs) for sensitive small-molecule detections. The coupling mechanism was verified by three-dimensional finite-difference time-domain calculations and experiments. AuNPs on CGN form image dimer assemblies and induce image dipole with resonance wavelengths ranging from 730 to 550 nm. The surface plasmon polaritons (SPPs) interact with the image dipole of the AuNP on the CGNs and then scatter out through the periodic gold caps. The experimental results show that the peak intensity of grating resonance is decreased by the effect of image dipole and exhibits the maximum intensity change when the Fano resonance matches the resonance of image dipole. The 50 nm AuNPs can be detected with a surface density of less than one particle/μm² by using the intensity change as the signal. With the resonant coupling between Fano resonance and image dipole extinction, the oligonucleotide with a molecular weight of 5.5 kDa can be detected at a concentration of 100 fM. The resonant coupling dramatically pushes the sensitivity boundary, and we report the limit of detection (LOD) to be 3 orders of magnitude lower than that of the prism-based SPR. This study provides a promising and efficient method for detecting low concentrations of small molecules such as aptamers, miRNA, mRNA, and peptides.

Surface Plasmon Resonance of Two-Dimensional Gold Colloidal Crystals Formed on Gold Plates

The free electrons inside precious metals such as Au vibrate when the surface of the metal is irradiated with an electromagnetic wave of an appropriate frequency. This oscillation is referred to as surface plasmon resonance (SPR), and the resonance frequency varies with permittivity of the medium around the metal. SPR sensors are widely applied in the fields of bioscience and pharmaceutical sciences, including biosensing for drug discovery, biomarker screening, virus detection, and testing for food safety. Here, we fabricated a metal-insulator-metal (MIM) SPR sensor by constructing two-dimensional (2D) regular array of Au colloidal particles (2D colloidal crystals) on an insulator layer over a thin Au film coated on a glass substrate surface. The 2D crystals were fabricated by electrostatically adsorbing negatively charged three-dimensional crystals onto a positively charged thin insulator formed on Au film. The plasmon peaks/dips from the MIM structure were measured in aqueous solutions of ethylene glycol (EG) at various concentrations. Multiple plasmon peaks/dips were observed due to the localized SPR (LSPR) of the Au particles and the Fano resonance between the Au particles and thin film. The plasmon peaks/dips shifted to higher wavelengths on increasing EG concentrations due to an increase in the refractive index of the media. The observed peak/dip shift was approximately twice that of LSPR from an isolated Au particle. We expect the present MIM substrate will be useful as a highly sensitive sensor in the pharmaceutical field.

Analysis of the surface plasmon resonance interferometric imaging performance of scanning confocal surface plasmon microscopy

Here, we apply rigorous coupled-wave theory to analyze the optical phase imaging performance of scanning confocal surface plasmon microscope. The scanning confocal surface plasmon resonance microscope is an embedded interferometric microscope interfering between two integrated optical beams. One beam is provided by the central part around the normal incident angle of the back focal plane, and the other beam is the incident angles beyond the critical angle, exciting the surface plasmon. Furthermore, the two beams can form an interference signal inside a confocal pinhole in the image plane, which provides a well-defined path for the surface plasmon propagation. The scanning confocal surface plasmon resonance microscope operates by scanning the sample along the optical axis z, so-called V(z). The study investigates two imaging modes: non-quantitative imaging and quantitative imaging modes. We also propose a theoretical framework to analyze the scanning confocal surface plasmon resonance microscope compared to non-interferometric surface plasmon microscopes and quantify quantitative performance parameters including spatial resolution and optical contrast for non-quantitative imaging; sensitivity and crosstalk for quantitative imaging. The scanning confocal SPR microscope can provide a higher spatial resolution, better sensitivity, and lower crosstalk measurement. The confocal SPR microscope configuration is a strong candidate for high throughput measurements since it requires a smaller sensing channel than the other SPR microscopes.

Non-productive binding of cellobiohydrolase i investigated by surface plasmon resonance spectroscopy

Future biorefineries are facing the challenge to separate and depolymerize biopolymers into their building blocks for the production of biofuels and basic molecules as chemical stock. Fungi have evolved lignocellulolytic enzymes to perform this task specifically and efficiently, but a detailed understanding of their heterogeneous reactions is a prerequisite for the optimization of large-scale enzymatic biomass degradation. Here, we investigate the binding of cellulolytic enzymes onto biopolymers by surface plasmon resonance (SPR) spectroscopy for the fast and precise characterization of enzyme adsorption processes. Using different sensor architectures, SPR probes modified with regenerated cellulose as well as with lignin films were prepared by spin-coating techniques. The modified SPR probes were analyzed by atomic force microscopy and static contact angle measurements to determine physical and surface molecular properties. SPR spectroscopy was used to study the activity and affinity of Trichoderma reesei cellobiohydrolase I (CBHI) glycoforms on the modified SPR probes. N-glycan removal led to no significant change in activity or cellulose binding, while a slightly higher tendency for non-productive binding to SPR probes modified with different lignin fractions was observed. The results suggest that the main role of the N-glycosylation in CBHI is not to prevent non-productive binding to lignin, but probably to increase its stability against proteolytic degradation. The work also demonstrates the suitability of SPR-based techniques for the characterization of the binding of lignocellulolytic enzymes to biomass-derived polymers.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10570-021-04002-6.

A multiplex and regenerable surface plasmon resonance (MR-SPR) biosensor for DNA detection of genetically modified organisms

The continuous advancement of analytical technology has provided methods with increasing sensitivity and precision to detect genetically modified organisms (GMOs). Novel analytical strategy-based detection methods are alternatives to conventional polymerase chain reaction (PCR)-mediated assays, which are still the gold standard in this field. However, PCR primers and probes cannot be reused, which makes the technique uneconomical. Surface plasmon resonance (SPR) is an optical and label-free technique for studying ligand-analyte interactions, especially for DNA hybridization, and several SPR biosensors have been described for the detection of nucleic acids. Here, a multiplexed, regenerable and real-time SPR biosensor for the detection of GMOs is described. A biosensor was constructed for qualitative detection of T-nos, CaMV35S and cry1A and had good specificity and sensitivity. The limit of detection (LOD) of this biosensor was 0.1 nM without any signal amplification. Furthermore, our biosensor could be stably regenerated more than 100 times over at least 20 days and showed good reproducibility. This nucleic acid SPR biosensor has potential for application in other types of biological detection.

Plasmonic mode coupling and thin film sensing in metal-insulator-metal structures

Optical sensors based on surface plasmon resonance (SPR) in the attenuated total reflection (ATR) configuration in layered media have attracted considerable attention over the past decades owing to their ability of label free sensing in biomolecular interaction analysis, and highly sensitive detection of changes in refractive index and thickness, i.e. the optical thickness, of thin film adsorbates (thin film sensing). Furthermore, SPR is highly sensitive to the refractive index of the medium adjacent to the bare metal, and it allows for bulk sensing as well. When deposited at the metal/air interface, an adsorbed layer disturbs the highly localized, i.e. bound, wave at this interface and changes the plasmon resonance to allow for sensing in angular or wavelength interrogation and intensity measurement modes. A high degree of sensitivity is required for precise and efficient sensing, especially for biomolecular interaction analysis for early stage diagnostics; and besides conventional SPR (CSPR), several other configurations have been developed in recent years targeting sensitivity, including long-range SPR (LRSPR) and waveguide-coupled SPR (WGSPR) observed in MIM structures, referred here to by MIM modes, resulting from the coupling of SPRs at I/M interfaces, and Fano-type resonances occurring from broad and sharp modes coupling in layered structures. In our previous research, we demonstrated that MIM is better than CSPR for bulk sensing, and in this paper, we show that CSPR is better than MIM for thin film sensing for thicknesses of the sensing layer (SL) larger than 10 nm. We discuss and compare the sensitivity of CSPR and MIM for thin film sensing by using both experiments and theoretical calculations based on rigorous electromagnetic (EM) theory. We discuss in detail MIM modes coupling and anti-crossing, and we show that when a thin film adsorbate, i.e. a SL), is deposited on top of the outermost-layer of an optimized MIM structure, it modifies the characteristics of the coupled modes of the structure, and it reduces the electric field, both inside the SL and at the SL/air interface, and as a result, it decreases the sensitivity of the MIM versus the CSPR sensor. Our work is of critical importance to plasmonic mode coupling using MIM configurations, as well as to optical bio- and chemical-sensing.

Recent Advances in Antifouling Materials for Surface Plasmon Resonance Biosensing in Clinical Diagnostics and Food Safety

Strategies to develop antifouling surface coatings are crucial for surface plasmon resonance (SPR) sensing in many analytical application fields, such as detecting human disease biomarkers for clinical diagnostics and monitoring foodborne pathogens and toxins involved in food quality control. In this review, firstly, we provide a brief discussion with considerations about the importance of adopting appropriate antifouling materials for achieving excellent performances in biosensing for food safety and clinical diagnosis. Secondly, a non-exhaustive landscape of polymeric layers is given in the context of surface modification and the mechanism of fouling resistance. Finally, we present an overview of some selected developments in SPR sensing, emphasizing applications of antifouling materials and progress to overcome the challenges related to the detection of targets in complex matrices relevant for diagnosis and food biosensing.

A Multi-Objective Optimization of 2D Materials Modified Surface Plasmon Resonance (SPR) Based Sensors: An NSGA II Approach

Modifying the structure of surface plasmon resonance based sensors by adding 2D materials has been proven to considerably enhance the sensor’s sensitivity in comparison to a traditional three layer configuration. Moreover, a thin semiconductor film placed on top of the metallic layer and stacked together with 2D materials enhances even more sensitivity, but at the cost of worsening the plasmonic couplic strength at resonance (minimum level of reflectivity) and broadening the response. With each supplementary layer added, the complexity of optimizing the performance increases due to the extended parameter space of the sensor. This study focused on overcoming these difficulties in the design process of sensors by employing a multi-objective genetic algorithm (NSGA II) alongside a transfer matrix method (TMM) and, at the same time, optimizing the sensitivity to full width at half maximum (FWHM), and the reflectivity level at a resonance for a four layer sensor structure. Firstly, the thin semiconductor’s refractive index was optimized to obtain the maximum achievable sensitivity with a narrow FWHM and a reflectivity level at a resonance of almost zero. Secondly, it was shown that refractive indices of barium titanate (BaTiO3) and silicon (Si) are the closest to the optimal indices for the silver—graphene/WS2 and MoS2 modified structures, respectively. Sensitivities up to 302 deg/RIU were achieved by Ag–BaTIO3–graphene/WS2 configurations with an FWHM smaller than 8 deg and a reflectivity level less than 0.5% at resonance.

Quantum Plasmonic Sensors

The extraordinary sensitivity of plasmonic sensors is well-known in the optics and photonics community. These sensors exploit simultaneously the enhancement and the localization of electromagnetic fields close to the interface between a metal and a dielectric. This enables, for example, the design of integrated biochemical sensors at scales far below the diffraction limit. Despite their practical realization and successful commercialization, the sensitivity and associated precision of plasmonic sensors are starting to reach their fundamental classical limit given by quantum fluctuations of light-known as the shot-noise limit. To improve the sensing performance of these sensors beyond the classical limit, quantum resources are increasingly being employed. This area of research has become known as "quantum plasmonic sensing", and it has experienced substantial activity in recent years for applications in chemical and biological sensing. This review aims to cover both plasmonic and quantum techniques for sensing, and it shows how they have been merged to enhance the performance of plasmonic sensors beyond traditional methods. We discuss the general framework developed for quantum plasmonic sensing in recent years, covering the basic theory behind the advancements made, and describe the important works that made these advancements. We also describe several key works in detail, highlighting their motivation, the working principles behind them, and their future impact. The intention of the review is to set a foundation for a burgeoning field of research that is currently being explored out of intellectual curiosity and for a wide range of practical applications in biochemistry, medicine, and pharmaceutical research.

Development and perspectives of rapid detection technology in food and environment

Food safety become a hot issue currently with globalization of food trade and food supply chains. Chemical pollution, microbial contamination and adulteration in food have attracted more attention worldwide. Contamination with antibiotics, estrogens and heavy metals in water environment and soil environment have also turn into an enormous threat to food safety. Traditional small-scale, long-term detection technologies have been unable to meet the current needs. In the monitoring process, rapid, convenient, accurate analysis and detection technologies have become the future development trend. We critically synthesizing the current knowledge of various rapid detection technology, and briefly touched upon the problem which still exist in research process. The review showed that the application of novel materials promotes the development of rapid detection technology, high-throughput and portability would be popular study directions in the future. Of course, the ultimate aim of the research is how to industrialization these technologies and apply to the market.

Combined SPRi Sensor for Simultaneous Detection of Nitrate and Ammonium in Wastewater

Water pollution is a serious problem in modern society. Agriculture, being responsible for the discharge of agrochemicals, organic matter, or drug residues, produces a huge amount of wastewater. Aquaponics has the potential to reduce both water consumption and the impact of water pollution on fish farming and plant production. In the aquatic environment, inorganic nitrogen is mostly present in the form of nitrate and ammonium ions. Nitrate, as a final product of ammonia mineralization, is the most common chemical contaminant in aquifers around the world. For continuous monitoring of nitrogen compounds in wastewater, we propose a sensor for the simultaneous detection of nitrate and ammonium. A surface plasmon resonance imaging method with enzyme-mediated detection was used. Active layers of nitrate reductase and glutamine synthetase were created on the gold surface of a biochip and tested for the sensing of nitrate and ammonium in water from an aquaponic system. The proposed sensor was applied in water samples with a concentration of NO3- and NH4+ in a range between 24-780 mg·L-1 and 0.26-120 mg·L-1, respectively, with minimal pretreatment of a sample by its dilution with a buffer prior to contact on a biochip surface.

Fiber Optic Particle Plasmon Resonance Biosensor for Label-Free Detection of Nucleic Acids and Its Application to HLA-B27 mRNA Detection in Patients with Ankylosing Spondylitis

We developed a label-free, real-time, and highly sensitive nucleic acid biosensor based on fiber optic particle plasmon resonance (FOPPR). The biosensor employs a single-strand deoxyoligonucleotides (ssDNA) probe, conjugated to immobilized gold nanoparticles on the core surface of an optical fiber. We explore the steric effects on hybridization affinity and limit of detection (LOD), by using different ssDNA probe designs and surface chemistries, including diluent molecules of different lengths in mixed self-assembled monolayers, ssDNA probes of different oligonucleotide lengths, ssDNA probes in different orientations to accommodate target oligonucleotides with a hybridization region located unevenly in the strand. Based on the optimized ssDNA probe design and surface chemistry, we achieved LOD at sub-nM level, which makes detection of target oligonucleotides as low as 1 fmol possible in the 10-μL sensor chip. Additionally, the FOPPR biosensor shows a good correlation in determining HLA-B27 mRNA, in extracted blood samples from patients with ankylosing spondylitis (AS), with the clinically accepted real-time reverse transcription-polymerase chain reaction (RT-PCR) method. The results from this fundamental study should guide the design of ssDNA probe for anti-sense sensing. Further results through application to HLA-B27 mRNA detection illustrate the feasibility in detecting various nucleic acids of chemical and biological relevance.

Sensitivity Improvement of a Surface Plasmon Resonance Sensor Based on Two-Dimensional Materials Hybrid Structure in Visible Region: A Theoretical Study

In this paper, we propose a surface plasmon resonance (SPR) sensor based on two-dimensional (2D) materials (graphene, MoS₂, WS₂ and WSe₂) hybrid structure, and theoretically investigate its sensitivity improvement in the visible region. The thickness of metal (Au, Ag or Cu) and the layer number of each 2D material are optimized using genetic algorithms to obtain the highest sensitivity for a specific wavelength of incident light. Then, the sensitivities of proposed SPR sensors with different metal films at various wavelengths are compared. An Ag-based SPR sensor exhibits a higher sensitivity than an Au- or Cu-based one at most wavelengths in the visible region. In addition, the sensitivity of the proposed SPR sensor varies obviously with the wavelength of incident light, and shows a maximum value of 159, 194 or 155°/RIU for Au, Ag or Cu, respectively. It is demonstrated that the sensitivity of the SPR sensor based on 2D materials’ hybrid structure can be further improved by optimizing the wavelength of incident light.

Resolution-improved SPR sensor with a rotational modulation method

A resolution-improved prism coupler-based surface plasmon resonance (SPR) sensor with a simple, effective rotational modulation method is proposed in this paper. For a conventional SPR sensor, the way to improve its measurement resolution is usually to use the rotating device with higher resolution. Measurement resolution depends on the modulation resolution of the incident angle; therefore, we propose a rotational modulation method that is implemented by rotating the prism horizontally to improve the modulation resolution of the incident angle, instead of using a more expensive rotating device with higher resolution. This scheme is validated both theoretically and experimentally. Furthermore, theoretical simulations show that the rotational modulation method can also be applied to long-range surface plasmon resonance sensors for better results.

High-Sensitivity Terahertz Refractive Index Sensor in a Multilayered Structure with Graphene

In this paper, we propose a high-sensitivity optical sensor at terahertz frequencies based on a composite structure containing a one-dimensional photonic crystal (1D PC) coated with a layer of monolayer graphene. Between the 1D PC and the graphene there is a sensing medium. This high-sensitivity phenomenon originates from the excitation of optical resonance between the graphene and the 1D PC. The proposed sensor is highly sensitive to the Fermi energy of graphene, the thickness and refractive index of the sensing medium, and the number of graphene layers. By selecting appropriate parameters, the maximum sensitivity (407.36∘/RIU) is obtained. We believe the proposed configuration is promising for fabricating graphene-based biosensor- or gas-sensor devices and other related applications in the terahertz band.

Spectral contrast imaging method for mapping transmission surface plasmon images in metallic nanostructures

We propose a spectral contrast method to map the transmission images of surface plasmon resonance (SPR) in metallic nanostructures. Comparing the intensities between two neighboring wavelength bands near the SPR wavelength, the signal-to-noise ratio for biosensing applications obtained using the proposed method is found to be ten times higher than that obtained by conventional intensity analysis and 1.6 times better than that obtained by peak-wavelength fitting. The dynamic range and linearity of the refractive index are comparable to the peak-wavelength shift measurement. Based on the detection method, a spectral modulation system for the optical microscope is developed, combined with a gold-capped nanowire array, to measure the biointeractions in microfluidic devices. The experimental results show that the proposed method obtained multiple detections with a detection limit of 1.04 × 10^-5 refractive index units. Two types of analysis methods for SPR images are used to study the protein-antibody interactions. The region-of-interest analysis supports multiplexing detections in a compact microfluidic sensor. The effective pixel analysis eliminates low-response pixels and enhances the signal-to-noise ratios for sensitive label-free detection.

Temperature Sensor Based on Side-Polished Fiber SPR Device Coated with Polymer

A highly sensitive temperature sensor based on surface plasmon resonance (SPR) of a side-polished single mode fiber is demonstrated. The sensor consists of a gold film coated side-polished fiber covered by a layer of UV-curable adhesive. Before introducing the UV-curable adhesive, the gold-coated fiber exhibits refractive index (RI) sensitivity of 1691.6 nm/RIU to 8800 nm/RIU in the range of 1.32 to 1.43. The resonant wavelength of the SPR sensor shifts to 650 nm when the adhesive is coated on the gold film, and is fixed at about 725 nm when the adhesive is cured. Due to the high thermo-optic and thermal expansion coefficient of the adhesive, the sensor structure achieves a temperature sensitivity of −0.978 nm/°C between 25 °C and 100 °C. The proposed optical fiber SPR sensor is simple, highly sensitive and cost effective, which may find potential applications for temperature measurements in the biomedical and environmental industries.

Surface plasmon resonance immunosensor for label-free detection of BIRC5 biomarker in spontaneously occurring canine mammary tumours

We report detection of Baculoviral inhibitor of apoptosis repeat containing-5 (BIRC5) protein biomarker in dog serum by label-free surface plasmon resonance (SPR) immunosensor. Initially, overexpression of BIRC5 in canine mammary tumour (CMT) tissues was confirmed by real-time PCR. Recombinant BIRC5 was produced and protein specific antibodies developed in guinea pig specifically reacted with native protein in immunohistochemistry and immunocytochemistry. SPR immunosensor was developed by fabricating anti-BIRC5 antibodies on gold sensor disc. The equilibrium dissociation constant, (K_D = k_d/k_a) was 12.1 × 10⁻¹² M; which indicates that antibodies are of high affinity with sensitivity in picomolar range. The SPR assay could detect as low as 6.25 pg/ml of BIRC5 protein in a calibration experiment (r² = 0.9964). On testing real clinical samples, 95% specificity and 73.33% sensitivity were recorded. The average amount of serum BIRC5 in dogs with CMT was 110.02 ± 9.77 pg/ml; whereas, in non-cancerous disease conditions, 44.79 ± 4.28 pg/ml and in healthy dog sera 30.28 ± 2.99 pg/ml protein was detected. The SPR immunosensor for detection of BIRC5 in dog sera is reported for the first time and this may find prognostic and diagnostic applications in management of CMT. In future, ‘on-site’ sensors can be developed using this technique for near-patient testing.

Surface plasmon resonance (SPR) biosensors for food allergen detection in food matrices

Food allergies are recognized as a growing public health concern, with an estimated 3% of adults and 6-8% of children affected by food allergy disorders. Hence, food allergen detection, labeling, and management have become significant priorities within the food industry, and there is an urgent requirement for reliable, sensitive, and user-friendly technologies to trace food allergens in food products. In this critical review, we provide a comprehensive overview of the principles and applications of surface plasmon resonance (SPR) biosensors in the identification and quantification of food allergens (milk, egg, peanut, and seafood), including fiber-optic surface plasmon resonance (FOSPR), surface plasmon resonance imaging (SPRI), localized surface plasmon resonance (LSPR), and transmission surface plasmon resonance (TSPR). Moreover, the characteristics and fitness-for-purpose of each reviewed SPR biosensor is discussed, and the potential of newly developed SPR biosensors for multi-allergen real-time detection in a complex food system is highlighted. Such SPR biosensors are also required to facilitate the reliable, high-throughput, and real-time detection of food allergens by the food control industry and food safety control officials to easily monitor cross-contamination during food processing.

Early detection of bacteria using SPR imaging and event counting: experiments with Listeria monocytogenes and Listeria innocua

Foodborne pathogens are of significant concern in the agrifood industry and the development of associated rapid detection and identification methods are of major importance. This paper describes the novel use of resolution-optimized prism-based surface plasmon resonance imaging (RO-SPRI) and data processing for the detection of the foodborne pathogens Listeria monocytogenes and Listeria innocua. With an imaging spatial resolution on the order of individual bacteria (2.7 ± 0.5 μm × 7.9 ± 0.6 μm) over a field of view 1.5 mm2, the RO-SPRI system enabled accurate counting of individual bacteria on the sensor surface. Using this system, we demonstrate the detection of two species of Listeria at an initial concentration of 2 × 102 CFU mL-1 in less than 7 hours. The surface density of bacteria at the point of positive detection was 15 ± 4 bacteria per mm2. Our approach offers great potential for the development of fast specific detection systems based on affinity monitoring.

Recent progress in the development of recognition bioelements for polychlorinated biphenyls detection: Antibodies and aptamers

Polychlorinated biphenyls (PCBs) are persistent pollutants, which have expanded in foods and the environment. Detection of PCBs is considered essential due to recognized side-effects of PCBs on health and the public concerns in this regard. On the other hand, due to the trace levels of these organic chlorine compounds, reliable and sensitive assays must be developed. Recognition elements are essential parts of analytical detection assays and sensors of PCBs since these elements are involved in the selective identification of the analytes of interest. Understanding the fundamentals of the recognition elements of PCBs and the benefits of the sensor strategies result in the development of next-generation recognition devices. This review aimed to highlight the recent progress in the recognition elements as key parts of biosensors. We initially, focused on the developed antibody-based biosensors for the detection of PCBs, followed by discussing the aptamers as novel recognition elements. Furthermore, the recent advancement in the development of aptamer-based solid phase extractions has been evaluated. These findings could contribute to improving the design of commercial PCB-kits in the future.

Dielectrophoretic cell trapping for improved surface plasmon resonance imaging sensing

The performance of conventional surface plasmon resonance (SPR) biosensors can be limited by the diffusion of the target analyte to the sensor surface. This work presents an SPR biosensor that incorporates an active mass-transport mechanism based on dielectrophoresis and electroosmotic flow to enhance analyte transport to the sensor surface and reduce the time required for detection. Both these phenomena rely on the generation of AC electric fields that can be tailored by shaping the electrodes that also serve as the SPR sensing areas. Numerical simulations of electric field distribution and microparticle trajectories were performed to choose an optimal electrode design. The proposed design improves on previous work combining SPR with DEP by using face-to-face electrodes, rather than a planar interdigitated design. Two different top-bottom electrode designs were experimentally tested to concentrate firstly latex beads and secondly biological cells onto the SPR sensing area. SPR measurements were then performed by varying the target concentrations. The electrohydrodynamic flow enabled efficient concentration of small objects (3 μm beads, yeasts) onto the SPR sensing area, which resulted in an order of magnitude increased SPR response. Negative dielectrophoresis was also used to concentrate HEK293 cells onto the metal electrodes surrounded by insulating areas, where the SPR response was improved by one order of magnitude.

Performance improvement of plasmonic sensors using a combination of AC electrokinetic effects for (bio)target capture

Analytes concentration techniques are being developed with the appealing expectation to boost the performance of biosensors. One promising method lies in the use of electrokinetic forces. We present hereafter a new design for a microstructured plasmonic sensor which is obtained by conventional microfabrication techniques, and which can easily be adapted on a classical surface plasmon resonance imaging (SPRI) system without further significant modification. Dielectrophoretic trapping and electro-osmotic displacement of the targets in the scanned fluid are performed through interdigitated 200 μm wide gold electrodes that also act as the SPR-sensing substrate. We demonstrate the efficiency of our device's collection capabilities for objects of different sizes (200 nm and 1 μm PS beads, as well as 5-10 μm yeast cells). SPRI is relevant for the spatial analysis of the mass accumulation at the electrode surface. We demonstrate that our device overcomes the diffusion limit encountered in classical SPR sensors thanks to rapid collection capabilities (<1 min) and we show a consequent improvement of the detection limit, by a factor >300. This study of an original device combining SPRI and electrokinetic forces paves the way to the development of fully integrated active plasmonic sensors with direct applications in life sciences, electrochemistry, environmental monitoring and agri-food industry.

Sequential sandwich immunoassay for simultaneous detection in trace samples using single-channel surface plasmon resonance

An efficient and facile method of a sequential sandwich immunoassay was developed for simultaneous detection in trace samples using single-channel SPR with low-dosage samples and testing times.

Control of Probe Density at DNA Biosensor Surfaces Using Poly(l-lysine) with Appended Reactive Groups

Biosensors and materials for biomedical applications generally require chemical functionalization to bestow their surfaces with desired properties, such as specific molecular recognition and antifouling properties. The use of modified poly(l-lysine) (PLL) polymers with appended oligo(ethylene glycol) (OEG) and thiol-reactive maleimide (Mal) moieties (PLL-OEG-Mal) offers control over the presentation of functional groups. These reactive groups can readily be conjugated to, for example, probes for DNA detection. Here we demonstrate the reliable conjugation of thiol-functionalized peptide nucleic acid (PNA) probes onto predeposited layers of PLL-OEG-Mal and the control over their surface density in the preceding synthetic step of the PLL modification with Mal groups. By monitoring the quartz crystal microbalance (QCM) frequency shifts of the binding of complementary DNA versus the density of Mal moieties grafted to the PLL, a linear relationship between probe density and PLL grafting density was found. Cyclic voltammetry experiments using Methylene Blue-functionalized DNA were performed to establish the absolute probe density values at the biosensor surfaces. These data provided a density of 1.2 × 10¹² probes per cm² per % of grafted Mal, thus confirming the validity of the density control in the synthetic PLL modification step without the need of further surface characterization.

Surface Plasmon Resonance Optical Sensor: A Review on Light Source Technology

The notion of surface plasmon resonance (SPR) sensor research emerged more than eight decades ago from the first observed phenomena in 1902 until the first introduced principles for gas sensing and biosensing in 1983. The sensing platform has been hand-in-hand with the plethora of sensing technology advancement including nanostructuring, optical technology, fluidic technology, and light source technology, which contribute to substantial progress in SPR sensor evolution. Nevertheless, the commercial products of SPR sensors in the market still require high-cost investment, component, and operation, leading to unaffordability for their implementation in a low-cost point of care (PoC) or laboratories. In this article, we present a comprehensive review of SPR sensor development including the state of the art from a perspective of light source technology trends. Based on our review, the trend of SPR sensor configurations, as well as its methodology and optical designs are strongly influenced by the development of light source technology as a critical component. These simultaneously offer new underlying principles of SPR sensor towards miniaturization, portability, and disposability features. The low-cost solid-state light source technology, such as laser diode, light-emitting diode (LED), organic light emitting diode (OLED) and smartphone display have been reported as proof of concept for the future of low-cost SPR sensor platforms. Finally, this review provides a comprehensive overview, particularly for SPR sensor designers, including emerging engineers or experts in this field.

Poisson pre-processing of nonstationary photonic signals: Signals with equality between mean and variance

Photonic signals are broadly exploited in communication and sensing and they typically exhibit Poisson-like statistics. In a common scenario where the intensity of the photonic signals is low and one needs to remove a nonstationary trend of the signals for any further analysis, one faces an obstacle: due to the dependence between the mean and variance typical for a Poisson-like process, information about the trend remains in the variance even after the trend has been subtracted, possibly yielding artifactual results in further analyses. Commonly available detrending or normalizing methods cannot cope with this issue. To alleviate this issue we developed a suitable pre-processing method for the signals that originate from a Poisson-like process. In this paper, a Poisson pre-processing method for nonstationary time series with Poisson distribution is developed and tested on computer-generated model data and experimental data of chemiluminescence from human neutrophils and mung seeds. The presented method transforms a nonstationary Poisson signal into a stationary signal with a Poisson distribution while preserving the type of photocount distribution and phase-space structure of the signal. The importance of the suggested pre-processing method is shown in Fano factor and Hurst exponent analysis of both computer-generated model signals and experimental photonic signals. It is demonstrated that our pre-processing method is superior to standard detrending-based methods whenever further signal analysis is sensitive to variance of the signal.

Phase-Sensitive Surface Plasmon Resonance Sensors: Recent Progress and Future Prospects

Surface plasmon resonance (SPR) is an optical sensing technique that is capable of performing real-time, label-free and high-sensitivity monitoring of molecular interactions. SPR biosensors can be divided according to their operating principles into angle-, wavelength-, intensity- and phase-interrogated devices. With their complex optical configurations, phase-interrogated SPR sensors generally provide higher sensitivity and throughput, and have thus recently emerged as prominent biosensing devices. To date, several methods have been developed for SPR phase interrogation, including heterodyne detection, polarimetry, shear interferometry, spatial phase modulation interferometry and temporal phase modulation interferometry. This paper summarizes the fundamentals of phase-sensitive SPR sensing, reviews the available methods for phase interrogation of these sensors, and discusses the future prospects for and trends in the development of this technology.

Neutralized chimeric DNA probe for detection of single nucleotide polymorphism on surface plasmon resonance biosensor

An implementation of neutralized chimeric DNA oligomer as a probe for sensitive detection of single nucleotide polymorphisms (SNPs) on a surface plasmon resonance imaging sensor is investigated. The chimeric DNA oligomer was synthesized in a conventional DNA synthesizer, containing neutral nucleotides with a methylated phosphate group. The secondary structures and melting points of the chimeric DNA fragment and its complexes with perfect-matched and single-mismatched complementary DNA molecules were examined by using circular dichroism and UV-vis spectroscopy in comparison with the native probe DNA counterpart. The results indicate that the chimeric DNA complexes can form a B-form structure and exhibit high thermostability. Moreover, the hybridization and discrimination efficiency of the chimeric probe DNA for the SNP genotyping were verified by using the SPRi sensor under different experimental conditions. The data reveal the effects of the ionic strength and operation temperature on the selectivity of the chimeric probe DNA for the SNP detection. The hybridization condition with a low ionic strength and high temperature allows the chimeric probe DNA distinguishing perfect-matched and single-mismatched target DNA molecules to the best extent, likely due to the reduced electrostatic repulsive force and presence of the additional methyl group on the backbone. Consequently, the direct and label-free detection with the SPR technique and neutralized chimeric probe DNA can be realized for the SNP genotyping by optimizing the operation condition and sequence design.

Surface plasmon resonance based competitive immunoassay for Cd2+

In this study, a label-free, specific and sensitive surface plasmon resonance (SPR) based competitive immunoassay was used for detecting Cd²⁺ in water samples.

Surface plasmon resonance sensor for antibiotics detection based on photo-initiated polymerization molecularly imprinted array

A surface plasmon resonance (SPR) sensor combined with nanoscale molecularly imprinted polymer (MIP) film as recognition element was developed for selective detection of the antibiotic ciprofloxacin (CIP). The MIP film on SPR sensor chip was prepared by in situ photo-initiated polymerization method which has the advantages of short polymerization time, controllable thickness and good uniformity. The surface wettability and thickness of MIP film on SPR sensor chip were characterized by static contact angle measurement and stylus profiler. The MIP-SPR sensor exhibited high selectivity, sensitivity and good stability for ciprofloxacin. The imprinting factors of the MIP-SPR sensor to ciprofloxacin and its structural analogue ofloxacin were 2.63 and 3.80, which is much higher than those to azithromycin, dopamine and penicillin. The SPR response had good linear relation with CIP concentration over the range 10^-11-10^-7molL^-1. The MIP-SPR sensor also showed good repeatability and stability during cyclic detections. On the basis of the photo-initiated polymerization method, a surface plasmon resonance imaging (SPRi) chip modified with three types of MIP sensing spots was fabricated. The MIPs-SPRi sensor shows different response patterns to ciprofloxacin and azithromycin, revealing the ability to recognize different antibiotic molecules.

Design and mechanisms of antifouling materials for surface plasmon resonance sensors

Surface plasmon resonance (SPR) biosensors have many possible applications, but are limited by sensor chip surface fouling, which blocks immobilization and specific binding by the recognizer elements. Therefore, there is a pressing need for the development of antifouling surfaces. In this paper, the mechanisms of antifouling materials were firstly discussed, including both theories (hydration and steric hindrance) and factors influencing antifouling effects (molecular structures and self-assembled monolayer (SAM) architectures, surface charges, molecular hydrophilicity, and grafting thickness and density). Then, the most recent advances in antifouling materials applied on SPR biosensors were systematically reviewed, together with the grafting strategies, antifouling capacity, as well as their merits and demerits. These materials included, but not limited to, zwitterionic compounds, polyethylene glycol-based, and polysaccharide-based materials. Finally, the prospective research directions in the development of SPR antifouling materials were discussed.

STATEMENT OF SIGNIFICANCE

Surface plasmon resonance (SPR) is a powerful tool in monitoring biomolecular interactions. The principle of SPR biosensors is the conversion of refractive index change caused by molecular binding into resonant spectral shifts. However, the fouling on the surface of SPR gold chips is ubiquitous and troublesome. It limits the application of SPR biosensors by blocking recognition element immobilization and specific binding. Hence, we write this paper to review the antifouling mechanisms and the recent advances of the design of antifouling materials that can improve the accuracy and sensitivity of SPR biosensors. To our knowledge, this is the first review focusing on the antifouling materials that were applied or had potential to be applied on SPR biosensors.

Development of a Portable Surface Plasmon Resonance Sensor with Multi-Sensing Points Based on the Linear CCD Sensor

A portable-type surface plasmon resonance (SPR) sensor, composed from a new optical system for multi-sensing, has been developed to apply to environment analysis, clinical diagnosis etc., where many samples are desired to be analyzed at high throughput. The optical system of the sensor consists of a light-emitting diode, a pair of cylindrical lenses, a pair of collimator lenses, a correction lens, a prism, a polarizer and a linear CCD sensor with 2048 pixels. Reflected light from a sensor chip of the width of 6 mm at a certain incident angle was detected by ca. 618 pixels of the linear CCD sensor as an SPR sensor signal. An SPR sensor signal at a specified incident angle is controllable for optimization by adjusting the position of the CCD sensor. A sensor chip having a 30-stripe linear pattern (100 μm width/stripe) was prepared. The spatial resolution as well as the performance of the sensor were evaluated by using sucrose solutions. As a result, the acquisition of SPR sensor signals from 30 sensing points was successfully achieved with a spatial resolution of 100 μm (distance between 2 sensing points). A lower detection limit of ca. 3.2 - 5.5 × 10(-5) RIU with a standard deviation of ±4.5% was obtained by averaging the signals from 6 - 7 pixels of the CCD sensor per one sensing stripe.