Investigation of immobilized filamentous fungi for treatment of real textile industry wastewater using up flow packed bed bioreactor

Investigating the effectiveness of rice husk-derived low-cost activated carbon in removing environmental pollutants: a study of its characterization

The chemically activated biochar was produced through the pyrolysis of rice husk. Thermal gravimetric and elemental analysis were conducted to characterize the raw rice husk. The activated biochar product underwent evaluation through SEM, BET and, FT-IR analysis. This cost-effective activated carbon was utilized as an adsorbent for the elimination of environmental pollutants. At a temperature of 25 °C, the activated biochar product exhibited an impressive maximum CO2 adsorption capacity of 152 mg/g. This exceptional performance can be attributed to its notable surface area and porosity, measuring at 2,298 m2/g and 0.812 cm3/g, respectively. This product was also utilized to remove methyl red (MR) dye from an aqueous solution. The optimal parameters for the removal of MR were determined as follows: a pH of 6.0, a temperature of 25 °C, an initial MR concentration of 50 mg/L, and an adsorbent dosage of 0.4 g/L. At a duration of 140 min, the system attained its maximum equilibrium adsorption capacity, reaching a value of 62.06 mg/g. Furthermore, the calculated maximum MR removal efficiency stood at an impressive 99.31%. The thermodynamic studies demonstrated that the MR removal process was spontaneous, exothermic, and increased randomness. Kinetic studies suggested that the pseudo-second-order model can fit well.

Microbial Interactions between Marine Microalgae and Fungi: From Chemical Ecology to Biotechnological Possible Applications

Chemical interactions have been shown to regulate several marine life processes, including selection of food sources, defense, behavior, predation, and mate recognition. These chemical communication signals have effects not only at the individual scale, but also at population and community levels. This review focuses on chemical interactions between marine fungi and microalgae, summarizing studies on compounds synthetized when they are cultured together. In the current study, we also highlight possible biotechnological outcomes of the synthetized metabolites, mainly for human health applications. In addition, we discuss applications for bio-flocculation and bioremediation. Finally, we point out the necessity of further investigating microalgae-fungi chemical interactions because it is a field still less explored compared to microalga-bacteria communication and, considering the promising results obtained until now, it is worthy of further research for scientific advancement in both ecology and biotechnology fields.

Sorghum-grown fungal biocatalysts for synthetic dye degradation

The synthetic dye discharge is responsible for nearly one-fifth of the total water pollution from textile industry, which poses both environmental and public health risks. Herein, a solid substrate inoculated with fungi is proposed as an effective and environmentally friendly approach for catalyzing organic dye degradation. Pleurotus ostreatus was inoculated onto commercially available solid substrates such as sorghum, bran, and husk. Among these, P. ostreatus grown on sorghum (PO-SORG) produced the highest enzyme activity and was further tested for its dye biodegradation ability. Four dye compounds, Reactive Blue 19 (RB-19), Indigo Carmine, Acid Orange 7, and Acid Red 1 were degraded by PO-SORG with removal efficiencies of 93%, 95%, 95%, and 78%, respectively. Under more industrially relevant conditions, PO-SORG successfully degraded dyes in synthetic wastewater and in samples collected from a local textile factory, which reveals its potential for practical usage. Various biotransformation intermediates and end-products were identified for each dye. PO-SORG exhibited high stability even under relatively extreme temperatures and pH conditions. Over 85% removal of RB-19 was achieved after three consecutive batch cycles, demonstrating reusability of this approach. Altogether, PO-SORG demonstrated outstanding reusability and sustainability and offers considerable potential for treating wastewater streams containing synthetic organic dyes.

Understanding the biodegradation pathways of azo dyes by immobilized white-rot fungus, Trametes hirsuta D7, using UPLC-PDA-FTICR MS supported by in silico simulations and toxicity assessment

No biodegradation methods are absolute in the treatment of all textile dyes, which leads to structure-dependent degradation. In this study, biodegradation of three azo dyes, reactive black 5 (RB5), acid blue 113 (AB113), and acid orange 7 (AO7), was investigated using an immobilized fungus, Trametes hirsuta D7. The degraded metabolites were identified using UPLC-PDA-FTICR MS and the biodegradation pathway followed was proposed. RB5 (92%) and AB113 (97%) were effectively degraded, whereas only 30% of AO7 was degraded. Molecular docking simulations were performed to determine the reason behind the poor degradation of AO7. Weak binding affinity, deficiency in H-bonding interactions, and the absence of interactions between the azo (-NN-) group and active residues of the model laccase enzyme were responsible for the low degradation efficiency of AO7. Furthermore, cytotoxicity and genotoxicity assays confirmed that the fungus-treated dye produced non-toxic metabolites. The observations of this study will be useful for understanding and further improving enzymatic dye biodegradation.

Biosorption of Eriochrome Black T Using Exserohilum rostratum NMS1.5 Mycelia Biomass

The presence of eriochrome black T (EBT) dye in waste water causes a significant hazard to human health and ecology. In the current study, biosorption was employed to eliminate EBT from water. Thus, we utilized endophytic fungi strain Exserohilum rostratum NMS1.5 mycelia biomass as biosorbent agent. The process was carried out at room temperature by magnetic stirring. The results indicated that an increase in pH would decrease adsorption capacity and removal percentage. In addition, an increased EBT concentration would decrease the removal percentage and increase biosorption capacity. The equilibrium time indicated that after 300 min of mixing, the percentage removal and biosorption capacity were 80.5% and 100.61 mg/g, respectively. The biosorption isotherms and kinetics were compatible with the Freundlich model and the pseudo-second-order. This research indicates that E. rostratum NMS1.5 may be utilized as an environmentally friendly and affordable alternative biosorbent material for EBT removal.

Biodegradation of Herbicide by the Immobilized Microbial Consortium SMC1 in Continuous Packed-Bed Biofilm Reactor

The present study aimed to investigate the treatment of butachlor and other commonly used herbicides by the synthetically formulated microbial consortium SMC1 immobilized on the ceramic raschig rings in a packed-bed bioreactor (PBBR). The PBBR was operated in continuous mode at various flow rates over a period of 70 days to determine the effect of hydraulic retention time (HRT) and initial butachlor concentration on the removal efficiency and elimination capability of the bioreactor. It was observed that the overall operation of the bioreactor changes from being controlled by the mass transfer limitations to the controlled bio-reaction , thus proposing the range of 270–325 mg/L/d to be the optimum operating range for the efficient removal of butachlor by the PBBR. The bioreactor can reduce up to 90% of the initial chemical oxygen demand (COD) value while treating the mixture of herbicides. The operating parameters were optimized using response surface methodology where the feed flow rate of 2.9 ml/min, initial herbicide concentration of 454.63 mg/L, and concentration of an additional nitrogen source at 1.41 g/L was found to yield maximal COD reduction. To date, a continuous study in the field of butachlor biodegradation is yet to be reported. Hence, the study could be used as a model to design a better herbicide biotreatment technology.

High dye removal capacity of Peniophora laxitexta immobilized in a combined support based on polyurethane foam and lignocellulosic substrates

Dye removal from effluents is a major problem for most textile industries. At present, wastewater treatments are currently based on physico-chemical methods which are expensive, energy inefficient and of limited versatility. The aim of this work was to find a low-cost and efficient method for dye removal. To do this, we designed a combined system based on the immobilization of the ligninolytic white-rot fungus Peniophora laxitexta (BAFC 4687) on mixed supports consisting of two polyurethane foam discs and a middle layer of diverse lignocellulosic substrates: soybean hulls, wheat straw or cellulose spent casings. As a corticioid fungus, P. laxitexta was able to completely colonize the supports developing a compact and tight structure that maintained the integrity of the system after several dye removal cycles. The immobilized fungus removed between 30% and 50% of the azoic dye Xylidine and more than 50% of the anthraquinonic dye RBBR in three successive cycles, and near 90% of the triphenylmethane Malachite Green in 10 repeated cycles without any loss of efficiency. Our analysis showed that the removal of the dyes was due to the combined effect of adsorption to the supports and enzymatic decolorization by soluble laccases and enzymes associated with the mycelium. Additionally, we showed that the presence of Malachite Green induced the expression of a new laccase isoform with high decolorization capacity. Based on these results, we propose that this inoculated laminar biocarrier could be effectively used for dye removal in textile wastewater.

Immobilization of Aspergillus oryzae DSM 1863 for l-Malic Acid Production

Whole-cell immobilization by entrapment in natural polymers can be a tool for morphological control and facilitate biomass retention. In this study, the possibility of immobilizing the filamentous fungus Aspergillus oryzae for l-malic acid production was evaluated with the two carbon sources acetate and glucose. A. oryzae conidia were entrapped in alginate, agar, and κ-carrageenan and production was monitored in batch processes in shake flasks and 2.5-L bioreactors. With glucose, the malic acid concentration after 144 h of cultivation using immobilized particles was mostly similar to the control with free biomass. In acetate medium, production with immobilized conidia of A. oryzae in shake flasks was delayed and titers were generally lower compared to cultures with free mycelium. While all immobilization matrices were stable in glucose medium, disintegration of bead material and biomass detachment in acetate medium was observed in later stages of the fermentation. Still, immobilization proved advantageous in bioreactor cultivations with acetate and resulted in increased malic acid titers. This study is the first to evaluate immobilization of A. oryzae for malic acid production and describes the potential but also challenges regarding the application of different matrices in glucose and acetate media.

Enhanced Efficiency of the Removal of Cytostatic Anthracycline Drugs Using Immobilized Mycelium of Bjerkandera adusta CCBAS 930

The aim of this study was to evaluate the bioremoval of anthracycline antibiotics (daunomycin-DNR, doxorubicin-DOX, and mitoxantrone-MTX) by immobilized mycelium of B. adusta CCBAS 930. The activity of oxidoreductases: versatile peroxidases (VP), superoxide dismutase (SOD), catalase (CAT), and glucose oxidase (GOX), and the levels of phenolic compounds (PhC) and free radicals (SOR) were determined during the biotransformation of anthracyclines by B. adusta strain CCBAS 930. Moreover, the phytotoxicity (Lepidium sativum L.), biotoxicity (MARA assay), and genotoxicity of anthracyclines were evaluated after biological treatment. After 120 h, more than 90% of anthracyclines were removed by the immobilized mycelium of B. adusta CCBAS 930. The effective biotransformation of anthracyclines was correlated with detoxification and reduced genotoxicity.

Talaromyces cellulolyticus as a promising candidate for biofilm construction and treatment of textile wastewater

Screening of microorganisms with broad-spectrum adaptability to extreme acid-base conditions and highperformance is essential for the construction of high-efficient biochemical wastewater treatment system. Herein, an acid-tolerant fungus isolated from acid medium was successfully identified through micromorphological observation and molecular characterization. The isolated fungus matched well with the filamentous fungus and was eventually identified as Talaromyces cellulolyticus. Considering the wide-range adaptability to pH condition (2.0-9.0), high cellulase activity (11.25 U mL^-1), ideal biofilm-forming property (17.87 mg cm^-3) on the surface of ceramsites, high tolerance to metal ions, and potential adsorption performance for aniline dyes, T. cellulolyticus issuitable for the construction of biofilm treatment system and treatment of textile wastewater based on the investigation of the removal efficiency of chemical oxygen demand and chromaticity of the synthetic textile wastewater. A promising candidate filamentous fungus for the treatment of textile wastewater was provided.

Bi-model cationic dye adsorption by native and surface-modified Trichoderma asperellum BPL MBT1 biomass: From fermentation waste to value-added biosorbent

In this study, we aimed to assess the possible reusability of native and surface-modified waste biomass of a novel ascomycetes fungi Trichoderma asperellum BPL MBT1 for the adsorption of triphenylmethane dyes. Spent biomass obtained from fermentation medium has been applied in the uptake of model cationic dyes viz., crystal violet and malachite green. Optimization of experimental parameters by batch mode studies revealed that dye adsorption is influenced by medium pH time, initial concentration of dyes, and adsorbent dosage. It was observed that pH 10 was optimum for cationic dye adsorption. Further, the adsorption process obeyed the bi-model (Langmuir-Freundlich model) isotherm and adhered to pseudo-second-order kinetics. The involvement of ion exchange as the dominant mechanism of dye adsorption was indicated by the mean free energy obtained from Dubinin-Radushkevich isotherm. Cellular morphology and the involved functional groups were studied by scanning electron microscopy and Fourier transform infrared spectroscopy that revealed the presence of carbon and oxygen containing groups on the surface. Maximum desorption efficiency was achieved using a 0.1 M solution of HCl and the stability of the biosorbent was confirmed through reusability analysis. Our results confirm the applicability of both native and surface-modified T. asperellum BPL MBT1 biomass as a potential biosorbent for the sustainable wastewater treatment and safe dye disposal.

Biosorption of cationic and anionic dyes using the biomass of Aspergillus parasiticus CBS 100926T

Aspergillus parasiticus (A. parasiticus) CBS 100926^T was used as a biosorbent for the removal of Methylene Blue (MB), Congo Red (CR), Sudan Black (SB), Malachite Green Oxalate (MGO), Basic Fuchsin (BF) and Phenol Red (PR) from aqueous solutions. The batch biosorption studies were carried out as a function of dye concentration and contact time. The biosorption process followed the pseudo-first-order and the pseudo-second-order kinetic models and the Freundlich and Langmuir isotherm models. The resulting biosorbent was characterized by Scanning Electron Microscopy (SEM), X-Ray Diffractometer and Fourier Transformer Infrared Spectroscopy (FTIR) techniques. The results of the present investigation suggest that A. parasiticus can be used as an environmentally benign and low cost biomaterial for the removal of basic and acid dyes from aqueous solution.

Textiles wastewater treatment technology: A review

The following is a review of published literature on textile wastewater in 2019. Presented are the sections described for the review: concise introduction on the textiles wastewater, followed by a review of present textile treatment technologies organized by physicochemical, biological, and combined processes. Lastly, a discussion of the future topics is presented. PRACTITIONER POINTS: The discharge of textile dye wastewater represents a serious environmental problem and public health concern. Effluents from textile manufacturing, dyeing, and finishing processes contain high-concentration recalcitrant chemicals that are resistant to biodegradation. The textile wastewater needs environmental-friendly and cost-effective combined treatment process.