Graft orientation influences meshing ratio

Modeling of metamaterial based incision patterns for generating high expansions in skin grafts

BACKGROUND

Split-thickness skin grafting is a widely used treatment for burn patients. It requires removing a small portion of healthy skin, making parallel incisions on it, stretching it, and surgically implanting it into the burn site. Although skin graft mesher companies claim to significantly expand the size of the skin graft, in reality, the amount of expansion achieved is much smaller.

METHODS

This study aimed to improve the expansion potential of skin grafts by designing new incision patterns with auxetic properties, using a skin simulant material and additive manufacturing. The mechanical properties and digital image correlation was used to analyze the strain, effective Poisson's ratio, local strains, void area, and meshing ratio of the auxetic skin graft simulants.

FINDINGS

The results showed that the Y-shaped skin graft simulant had the highest effective negative Poisson's ratio, largest areal expansions, lowest maximum induced stresses and strains, and uniform strain distribution properties, making it the best choice for generating high expansions in skin grafts.

INTREPRETATION

The study found that the expansions were highly strain sensitive, with higher auxeticity observed at lower strains. The novel findings with auxetic skin graft simulants are expected to provide valuable insights for developing skin grafts with higher expansion potential in the future.

Location specific multi-scale characterization and constitutive modeling of pig aorta

The mechanical and structural behavior of the aorta depend on physiological functions and vary from proximal to distal. Understanding the relation between regionally varying mechanical and multi-scale structural response of aorta can be helpful to assess the disease outcomes. Therefore, this study investigated the variation in mechanical and multi-scale structural properties among the major segments of aorta such as ascending aorta (AA), descending aorta (DA) and abdominal aorta (ABA), and established a relation between mechanical and multi-structural parameters. The obtained results showed significant increase in anisotropy and nonlinearity from proximal to distal aorta. The change in periphery length and radii between load and stress free configuration was also found increasing far from the heart. Opening angle was significantly large for ABA than AA and DA (AA/DA vs ABA; p = 0.001). Mean circumferential residual stretch (ratio of mean periphery length at load and stress free configurations) was found decreasing between AA and DA, and then increasing between DA to ABA and its value was significantly more for ABA (AA vs DA; p = 0.041, AA vs ABA; p = 0.001, DA vs ABA; p = 0.001). The waviness of collagen fibers, collagen fiber content, collagen fibril diameter and total protein content were found significantly increasing from proximal to distal. Pearson correlation test showed a significant linear correlation between variation in mechanical and multi-scale structural parameters over the aortic length. Residual stretch was found positively correlated with collagen fiber content (r = 0.82) whereas opening angel was found positively correlated with total protein content (TPC) (r = 0.76).

Biomechanical modeling of novel high expansion auxetic skin grafts

Over 20 million burn injuries are reported every year, with severe cases requiring skin grafting. Traditionally, split thickness skin grafts are prepared by excising a small portion of healthy skin and its incision patterning using a suitable meshing device, which allows the graft to be expanded beyond its capacity. To date, the maximum expansion achieved through skin grafting has been reported to be less than three times, which is not sufficient for covering large burn sites with limited donor site skin. In this work, we have attempted to study skin graft expansion potential with novel auxetic patterns, which are known to exhibit negative Poisson's effect. Two-layer skin graft models were developed using eight different auxetic incision patterns, and subjected to uniaxial and biaxial tensile strains. The Poisson's ratio, meshing ratio, and induced stresses were characterized for all graft models. The numerical results indicated expansion potentials greater than that of traditional skin grafts across all loads. Extremely high expansions (i.e., >30 times) were estimated for the I-Shaped Re-entrant and Rotating Triangles shaped auxetic models without rupture. Such pioneering findings are anticipated to initiate ground-breaking advances towards skin graft research and improved outcomes in burn surgeries.

Optimal structural pattern for maximal compliance using topology optimization based on phasefields: Application to improve skin graft meshing efficiency

This article focuses on the problem of maximal compliance design of a hyper-elastic solid with the optimal design of human skin grafts as the application in mind. The solution method is a phasefield-based topology optimization method that supposes multiple local phasefields and a minimum distance constraint in order to prevent the phasefields from merging. Consequently, structurally disintegrating solutions such as by the coalescence of voids can be prevented. The method is used to find an optimal graft meshing pattern for a sample that is subjected to a biaxial extension of up to 150%, which corresponds to an expansion ratio of 1 : 2.25. Three prospective unitcell solutions that exhibit meta-material behavior are proposed for a periodic graft pattern. The results are a step toward improving the skin graft meshing efficiency. This work does not cover experimental validation.

Comparison of different MyotonPRO probes for skin stiffness evaluation in young women

BACKGROUND

Stiffness of skin is widely used parameter in many research areas, for example cosmetic industry, dermatology or rheumatology for assessing of skin condition as well as changes occurring in skin. In this pioneering study, we conducted measurements of skin stiffness using MyotonPRO -novel tool, which was mainly used to evaluate biomechanical properties of muscles, ligaments and tendons. We expected that MyotonPRO , which shows great reproducibility in previous studies, will also be able to measure skin stiffness.

MATERIALS AND METHODS

Four replaceable probes designed by MyotonPRO (L-shape short and medium arm, standard cylindrical flat-end probe and the same standard probe with disc attachment ) were tested for measurement of skin stiffness in young women (30 healthy females) at three different locations (clavicula, volar forearm and shin).

RESULTS

There was no significant difference between stiffness values obtained with L-shape short and L-shape medium arm probes in all investigated areas. Stiffness values recorded by regular probe and regular probe with disc attachment differ significantly from those collected with L-shape probes. There was also significant difference between values of stiffness obtained by standard with disc attachment and standard probes.

CONCLUSION

Both L-shape probes show a great reliability for skin stiffness assessment. Therefore, MyotonPRO can be considered a reliable device for assessing skin stiffness.