Improved process for the production of cellulose sulfate using sulfuric acid/ethanol solution

Electrospinning of cellulose nanocrystals; procedure and optimization

Cellulose nanocrystals (CNCs) and cellulose microfibrils (CMFs) are promising materials with the potential to significantly enhance the mechanical properties of electrospun nanofibers. However, the crucial aspect of optimizing their integration into these nanofibers remains a challenge. In this work, we present a method to prepare and electrospin a cellulosic solution, aiming to overcome the existing challenges and realize the optimized incorporation of CNCs into nanofibers. The solution parameters of electrospinning were explored using a combined experimental and simulation (molecular dynamics) approach. Experimental results emphasize the impact of polymer solution concentration on fiber morphology, reinforcing the need for further optimization. Simulations highlight the intricate factors, including the molecular weight of cellulose acetate (CA) polymer chains, electrostatic fields, and humidity, that impact the alignment of CNCs and CMFs. Furthermore, efforts were made to study CNCs/CMFs alignment rate and quality optimization. It is predicted that pure CNCs benefit more from electrostatic alignment, while lower molecular weight CA enables better CNC/CMF alignment.

Tripolyphosphate-functionalized cellulose: A green solution for cadmium contamination

This study introduces a highly efficient tripolyphosphate -tethered cellulose sorbent for cadmium (Cd2⁺) removal from aqueous solutions. Characterization through FTIR and SEM revealed the material's structural properties. The sorbent achieved 99% Cd2⁺ removal even at a minimal dosage of 0.05 g. Optimal sorption occurred within the pH range of 4-6, influenced by the sorbent's weak acidic functional groups. Rapid kinetics, reaching equilibrium within a minute, and a high sorption capacity (up to 18.03 mg/g at 50 °C) were observed. Langmuir isotherm modeling confirmed monolayer sorption, and thermodynamic studies indicated a spontaneous, endothermic process with increased randomness at the solid-liquid interface. Selectivity studies demonstrated strong Cd2⁺ removal performance in the presence of competing ions, with minimal interference from monovalent ions but notable effects from divalent ions. The sorbent exhibited consistent reusability over multiple cycles. XPS analysis conclusively established an ion exchange mechanism between Cd2⁺ and negatively charged P3O105- groups as the primary removal pathway. This research highlights the potential of TPP-tethered cellulose as a promising sorbent for effective Cd2⁺ remediation.

Sulfonic acid functionalized cellulose-derived (nano)materials: Synthesis and application

The preparation/application of heterogeneous (nano)materials from natural resources has currently become increasingly fascinating for researchers. Cellulose is the most abundant renewable polysaccharide on earth. The unique physicochemical, structural, biological, and environmental properties of this natural biopolymer have led to its increased application in many fields. The more desirable features of cellulose-based (nano)materials such as biodegradability, renewability, biocompatibility, cost-effectiveness, simplicity of preparation, environmentally friendly nature, and widespread range of applications have converted them into promising compounds in medicine, catalysis, biofuel cells, and water/wastewater treatment processes. Functionalized cellulose-based (nano)materials containing sulfonic acid groups may prove to be one of the most promising sustainable bio(nano)materials of modern times in the field of cellulose science and (nano)technology owing to their intrinsic features, high crystallinity, high specific surface area, abundance, reactivity, and recyclability. In this review, the developments in the application of sulfonated cellulose-based (nano)materials containing sulfonic acid (-SO3H) groups in catalysis, water purification, biological/biomedical, environmental, and fuel cell applications have been reported. This review provides an overview of the methods used to chemically modify cellulose and/or cellulose derivatives in different forms, including nanocrystals, hydrogels, films/membranes, and (nano)composites/blends by introducing sulfonate groups on the cellulose backbone, focusing on diverse sulfonating agents utilized and substitution regioselectivity, and highlights their potential applications in different industries for the generation of alternative energies and products.

Preparation and characterization of sulfated nanocellulose: From hydrogels to highly transparent films

This study focuses on the production of sulfated cellulose microfibers and nanocellulose hydrogels from native cellulose microfibers (CMF). The process involves using a combination of H2SO4 and urea, resulting in highly sulfated cellulose microfiber hydrogel (SC) with notable properties such as a sulfur content of 7.5 %, a degree of sulfation of 0.49, a surface charge content of 2.2 mmol. g-1, and a high yield of 81 %. The SC hydrogel can be easily fibrillated into sulfated nanocellulose hydrogel (S-NC) with elongated nanocellulose structures having an average diameter of 6.85 ± 3.11 nm, as determined using atomic force microscopy (AFM). X-ray photoelectron spectroscopy (XPS) analysis confirms the presence of sulfate groups on the surface of the nanocellulose material. Transparent films with good mechanical properties can be produced from both cellulose microfiber and nanocellulose hydrogels. The sulfate functionality gives the hydrogel attractive rheological properties and makes S-NC re-dispersible in water, which can be beneficial for various applications. This study demonstrates the potential of this process to address previous challenges related to nanocellulose materials production.

Isotropic Gels of Cellulose Nanocrystals Grafted with Dialkyl Groups: Influence of Surface Group Topology from Nonlinear Oscillatory Shear

Attractive (non-self-assembling) aqueous cellulose nanocrystal (CNC) suspensions were topologically tailored into isotropic gels through the surface grafting of dialkyl groups. We thus focus on the influence of CNC concentration, including for pristine CNC, surface linker branching, branching degree, and the influence of side group size and branch-on-branch surface-grafted groups. The resulting mobility and strength of interaction in particle-particle interaction mediated by the surface groups was investigated from a rheological point of view. The emphasis is on nonlinear material parameters from Fourier-transform rheology and stress decomposition analysis. The results show that nonlinear material parameters are more sensitive than linear viscoelastic parameters to the onset of weakly interconnected networks in pristine CNC isotropic suspensions. All surface-modified CNC suspensions resulted in isotropic gels. The nonlinear material parameters were found to be broadly sensitive to CNC concentration, branching, degree of branching and surface-grafted linkers' length. However, the length of the grafted chains and the degree of branching were the primary factors influencing the nonlinear material response. Furthermore, the results showed evidence of two strain amplitude ranges with distinct nonlinear signatures that could be attributed to the disruption of weak network connection points and to distortions of more dense (aggregate) network regions, respectively.

Super absorbent glutaric anhydride-modified agar: Structure, properties, and application in biomaterial delivery

Agar was modified with glutaric anhydride (GA) in this study to expand its application in food and medicine. Glutaric anhydride-modified agar (GAR) can maintain high gel strength (1247.4 g/cm²) and improved transparency (82.7 %). The esterified agar formed by GA further formed a cross-linking molecule structure by increasing the reaction temperature. Notably, excellent freeze-thaw stability (24.1 %) and swelling property (3116.6 %) of GAR indicated that the carboxyl-terminal of modified agar improves its affinity with water. Therefore, satisfactory water permeability and expansive stone enable agar films to achieve high water absorption. Furthermore, GAR films exhibit a specific absorption capacity of tetracycline hydrochloride in weak acid solution, thereby suggesting its potential application as a sustainable drug delivery carrier. Finally, the structure of the modified agar was analyzed to explain the mechanism of binding water. Cryo-scanning electron microscopy (SEM) depicted the porous structure of the agar gel responsible for swelling, drug loading, and release. Low-field NMR results showed that GA improves agar gel's binding and free water content. According to our research results, these GAR hydrogel membranes with excellent properties have the potential to be used as effective drug delivery materials.

Modifications of cellulose-based biomaterials for biomedical applications

Cellulose is one of the most abundant organic compounds in nature and is available from diverse sources. Cellulose features tunable properties, making it a promising substrate for biomaterial development. In this review, we highlight advances in the physical processes and chemical modifications of cellulose that enhance its properties for use as a biomaterial. Three cellulosic products are discussed, including nanofibrillated, nanocrystalline, and bacterial cellulose, with a focus on how each may serve as a platform for the development of advanced cellulose-based biomaterials for Biomedical applications. In addition to associating mechanical and chemical properties of cellulosic materials to specific applications, a prospectus is offered for the future development of cellulose-based biomaterials for biomedicine.

Design of a Naturally Dyed and Waterproof Biotechnological Leather from Reconstituted Cellulose

Consumerism in fashion involves the excessive consumption of garments in modern capitalist societies due to the expansion of globalisation, especially at the beginning of the 21st Century. The involvement of new designers in the garment industry has assisted in creating a desire for new trends. However, the fast pace of transitions between collections has made fashion increasingly frivolous and capable of generating considerable interest in new products, accompanied by an increase in the discarding of fabrics. Thus, studies have been conducted on developing sustainable textile materials for use in the fashion industry. The aim of the present study was to evaluate the potential of a vegan leather produced with a dyed, waterproof biopolymer made of reconstituted bacterial cellulose (BC). The dying process involved using plant-based natural dyes extracted from Allium cepa L., Punica granatum, and Eucalyptus globulus L. The BC films were then shredded and reconstituted to produce uniform surfaces with a constant thickness of 0.10 cm throughout the entire area. The films were waterproofed using the essential oil from Melaleuca alternifolia and wax from Copernicia prunifera. The characteristics of the biotechnological vegan leather were analysed using scanning electron microscopy (SEM), thermogravimetric analysis (TGA), flexibility and mechanical tests, as well as the determination of the water contact angle (°) and sorption index (s). The results confirmed that the biomaterial has high tensile strength (maximum: 247.21 ± 16.52 N) and high flexibility; it can be folded more than 100 times at the same point without breaking or cracking. The water contact angle was 83.96°, indicating a small water interaction on the biotextile. The results of the present study demonstrate the potential of BC for the development of novel, durable, vegan, waterproof fashion products.

Synthesis and properties of maleic anhydride-modified agar with reversibly controlled gel strength

Agar is modified by chemical methods to improve its functional properties and meet the increasing demand of the market. Some of the functional properties of agar are improved after chemical modification, while other properties are reduced, especially gel strength. This study aimed to comprehensively improve the functional properties of agar through acylation and crosslinking by reacting with maleic anhydride. ¹³C NMR indicated the maleylation reaction was preferred at the C2 hydroxyl group of D-galactose, and the crosslinking reactions occurred at the C2 and C6 hydroxyl groups of D-galactose in different agar chains. Interestingly, the maleylated agar monoester had higher gel transparency (1.5%, w/v) of up to 76% than the native agar (58%). However, it showed a significant decrease in gel strength from 783 g/cm² to 403 g/cm², while crosslinking endowed agar with higher gel strength (845 g/cm²) and gel transparency (78.4%). The high transparency of the modified agar plate made colony observation and colony counting easy. Maleylation of agar further enhanced the freeze-thaw stability of agar gel (24.8%, 7th freeze-thaw cycles). Overall, the maleylated agar possessed superior functional properties, and it could be used as food, bacteriological, and biotechnological agar.

Two-pot Oxidative Preparation of Dicarboxylic Acid Containing Cellulose for the Removal of Beryllium (Be2+) from Aqueous Solution

Background:

Cellulose is one of the most abundant, non-toxic, and renewable natural biopolymers. The presence of hydroxyl groups in cellulose leads to further modification of it. Preparation and modification of cellulose-based sorbents and their applications on water treatment gained traction in recent years.

Objective:

A low-cost and eco-friendly biosorbent was designed and fabricated by introducing the acetate functional groups into cellulose for removing Beryllium (Be2+) from an aqueous solution. The so rption of Be2+ on acetate containing cellulose was evaluated for varying sorbent doses and initial solution pH values.

Method:

The sorbent was prepared by a two-step oxidation process. In the initial step, cellulose reacted with NaIO4 and aldehyde groups were introduced to cellulose. In the second step, newly obtained aldehyde groups were oxidized to create acetate groups.

Results:

The kinetics of the sorption process showed that Be2+ uptake reached equilibrium in 3 minutes. The sorption isotherm was well fitted in the Langmuir model, and maximum sorption capacity was 4.54 mg/g. Moreover, the thermodynamic studies demonstrated that Be2+ sorption is spontaneous and exothermic. Furthermore, the prepared sorbent can be regenerated by using 0.1 M HCl or H2SO4 solutions.

Conclusion:

Removal of Be2+ is pH dependent and it is favorable at high solution pH. The kinetics of the prepared sorbent is rapid and equilibrium attained in 3 minutes. The prepared sorbent can be regenerated with 0.1 M acid solution with > 99% efficiency.

Chemocatalytic value addition of glucose without carbon-carbon bond cleavage/formation reactions: an overview

As the monomeric unit of the abundant biopolymer cellulose, glucose is considered a sustainable feedstock for producing carbon-based transportation fuels, chemicals, and polymers. The chemocatalytic value addition of glucose can be broadly classified into those involving C-C bond cleavage/formation reactions and those without. The C6 products obtained from glucose are particularly satisfying because their syntheses enjoy a 100% carbon economy. Although multiple derivatives of glucose retaining all six carbon atoms in their moiety are well-documented, they are somewhat dispersed in the literature and never delineated coherently from the perspective of their carbon skeleton. The glucose-derived chemical intermediates discussed in this review include polyols like sorbitol and sorbitan, diols like isosorbide, furanic compounds like 5-(hydroxymethyl)furfural, and carboxylic acids like gluconic acid. Recent advances in producing the intermediates mentioned above from glucose following chemocatalytic routes have been elaborated, and their derivative chemistry highlighted. This review aims to comprehensively understand the prospects and challenges associated with the catalytic synthesis of C6 molecules from glucose.

Preparation and characterization of sodium cellulose sulfate/chitosan composite films loaded with curcumin for monitoring pork freshness

Colorimetric films were prepared by incorporating curcumin into a sodium cellulose sulfate/chitosan composite. The morphology mechanical, and water vapor properties of the films were investigated, and their practical use in pork preservation was evaluated. The formula with the same charge ratio of sodium cellulose sulfate and chitosan had the highest tensile strength (TS). After the addition of curcumin, the tensile strength increased, whereas the water vapor permeability (WVP) decreased. The colorimetric film showed distinguishable color changes between the pH ranges of 3–10. The colorimetric film packaging extended the shelf life of the pork samples by 4 days. Moreover, the composite films were able to effectively monitor pork freshness. In conclusion, curcumin incorporated into sodium cellulose sulfate/chitosan composite films may have great potential in food packaging.

•

Sodium cellulose sulfate/chitosan/curcumin films were produced for food packaging.

•

The properties of composite films were enhanced due to electrostatic interaction.

•

The composite films changed their colors in response to the change of pH.

•

The composite films could monitor the freshness and extend shelf life of pork.

Proton Conductive, Low Methanol Crossover Cellulose-Based Membranes

This work describes the development of sulfated cellulose (SC) polymer and explores its potential as an electrolyte-membrane for direct methanol fuel cells (DMFC). The fabrication of our membranes was initiated by the preparation of the novel sulfated cellulose solution via controlled acid hydrolysis of microcrystalline cellulose (MCC). Ion-conductive crosslinked SC membranes were prepared following a chemical crosslinking reaction. SC solution was chemically crosslinked with glutaraldehyde (GA) and cured at 30 °C to produce the aforementioned membranes. Effects of GA concentration on methanol permeability, proton conductivity, water uptake and thermal stabilities were investigated. The crosslinking reaction is confirmed by FTIR technique where a bond between the primary OH groups of cellulose and the GA aldehyde groups was achieved, leading to the increased hydrophobic backbone domains in the membrane. The results show that the time of crosslinking reaction highly affects the proton conduction and methanol permeability. The proton conductivity and methanol crossover (3M) of our GA crosslinked SC membranes are 3.7 × 10-2 mS cm-1 and 8.2 × 10-9 cm2 s-1, respectively. Crosslinked sulfated cellulose films have lower ion conductivity than the state-of-the-art Nafion (10.2 mS cm-1); however, the methanol crossover is three orders of magnitude lower than Nafion membranes (1.0 × 10-5 cm2 s-1 at 1 M). Such biofilms with high methanol resistivity address the major hurdle that prevents the widespread applications of direct alcohol fuel cells.

Solvent-free production of thermoplastic lignocellulose from wood pulp by reactive extrusion

A novel acylation approach suited to rapid bulk thermoplasticization of lignocellulose without solvents was previously demonstrated by the authors in benchtop batch studies. The method relies upon a benzethonium chloride/sulfuric acid functionalizing agent at low concentrations to act as a wetting agent for the wood pulp, similar to an ionic liquid, yet binds to the lignocellulose ester as a flow aid in the final thermoplastic. The present investigation evaluates the approach in a residence time-limited (45-90 s) continuous twin-screw reactor, where intensive mixing and heat were found to yield high acylation. The modified lignocellulose exhibited desired thermoplasticity by being melt moldable without the need for plasticizers and maintained much of the excellent stiffness of cellulose, demonstrating a maximum flexural modulus of 5.4 GPa and tensile modulus of 1.8 GPa. The influence of extrusion conditions on thermoplasticity was examined by a Design of Experiments (DOE) analysis.

Highly sulphated cellulose: a versatile, reusable and selective desilylating agent for deprotection of alcoholic TBDMS ethers

A mild, efficient and rapid protocol was developed for the deprotection of alcoholic TBDMS ethers using a recyclable, eco-friendly highly sulphated cellulose sulphate acid catalyst in methanol. This acid catalyst selectively cleaves alcoholic TBDMS ethers in bis-TBDMS ethers containing both alcoholic and phenolic TBDMS ether moieties.

Dispersion Process and Effect of Oleic Acid on Properties of Cellulose Sulfate- Oleic Acid Composite Film

The cellulose sulfate (CS) is a newly developed cellulose derivative. The work aimed to investigate the effect of oleic acid (OA) content on properties of CS-OA film. The process of oleic acid dispersion into film was described to evaluate its effect on the properties of the film. Among the formulations evaluated, the OA addition decreased the solubility and water vapor permeability of the CS-OA film. The surface contact angle changed from 64.2° to 94.0° by increasing CS/OA ratio from 1:0 to 1:0.25 (w/w). The TS increased with OA content below 15% and decreased with OA over 15%, but the ε decreased with higher OA content. The micro-cracking matrices and micro pores in the film indicated the condense structure of the film destroyed by the incorporation of oleic acid. No chemical interaction between the OA and CS was observed in the XRD and FTIR spectrum. Film formulation containing 2% (w/w) CS, 0.3% (w/w) glycerol and 0.3% (w/w) OA, showed good properties of mechanic, barrier to moisture and homogeneity.