Rheological and structural characterization of HA/PVA-SbQ composites film-forming solutions and resulting films as affected by UV irradiation time

Initiator-Free Photocuring 3D-Printable PVA-Based Hydrogel with Tunable Mechanical Properties and Cell Compatibility

Poly(vinyl alcohol) (PVA)-based hydrogels have attracted great attention and been widely used in biological tissue engineering. With the development of modern medicine, precision medicine requires the customization of medical materials. However, lacking of photocurable functional groups or the performance of rapid phase transition makes PVA-based hydrogels difficult to be customizable molded through photocuring 3D printing technique. In this research, customizable PVA-based hydrogels with high performance through 3D photocurable printing and freezing-thawing (F-T) process are obtained. The ability of 3D-printable is endowed by the introduction of polyvinyl alcohol-styrylpyridine (PVA-SBQ), which can be photo-crosslinked quickly without photoinitiator. Meanwhile, the tunable mechanical properties are achieved by adjusting the mass ratio of PVA-SBQ to PVA, and PVA can offer the physical crosslinking points through freezing-thawing (F-T) process. The hydrogels with high resolution are prepared by digital light procession 3D printing with the mass ratio 1:1 of PVA-SBQ to PVA solution. Attributed to the absence of initiator, and no small molecule residues inside the hydrogels, the hydrogels have good biocompatibility and have the potential to be applicated in the field of biological tissue engineering.

Injectable In Situ Photocrosslinked Hydrogel Dressing for Infected Wound Healing

A traditional injectable photocrosslinked hydrogel had disadvantages of the residual photoinitiator and toxic crosslinker, slow in situ curing, and a complex preparation process. At the same time, hydrogels cannot act as artificial skin to restore skin sensory function during the wound healing cycle. In this work, an injectable photocrosslinked hydrogel was prepared which can be quickly in situ cured without photoinitiator. Oxidized sodium alginate was used as a natural macromolecular crosslinking agent to form an injectable hydrogel framework with the photosensitive polymer polyvinyl alcohol bearing styrylpyridinium group (PVA-SBQ). In addition, the hydrogel was endowed with photothermal therapy property after the introduction of biomass-like polydopamine particles. When used as a wound dressing, the hydrogel exhibited an excellent antibacterial property, with an antibacterial rate of 99.56% Escherichia coli and 97.96% Staphylococcus aureus. As a result, the hydrogel could significantly accelerate the repair of infected wounds, with a wound healing rate of 96.45% after 14 days. Moreover, the hydrogel exhibited a sensitive and stable sensing property, making it promising to reconstitute the sensory function of damaged skin during treatment. This work provides an idea for the development of injectable photocrosslinked hydrogel dressing.

Current advances in the biosynthesis of hyaluronic acid with variable molecular weights

Hyaluronic acid (HA) is a naturally formed acidic mucopolysaccharide, with excellent moisturising properties and used widely in the medicine, cosmetics, and food industries. The industrial production of specific molecular weight HA has become imperative. Different biological activities and physiological functions of HA mainly depend on the degree of polymerisation. This article reviews the research status and development prospects of the green biosynthesis and molecular weight regulation of HA. There is an application-based prerequisite of specific molecular weight of HA that could be regulated either during the fermentation process or via a controlled HA degradation process. This work provides an important theoretical basis for the downstream efficient production of diversified HA, which will further accelerate the research applications of HA and provide a good scientific basis and method reference for the study of the molecular weight regulation of similar biopolymers.

Photodynamic Coatings on Polymer Microfibers for Pathogen Inactivation: Effects of Application Method and Composition

A substantial increase in the risk of hospital-acquired infections (HAIs) has greatly impacted the global healthcare industry. Harmful pathogens adhere to a variety of surfaces and infect personnel on contact, thereby promoting transmission to new hosts. This is particularly worrisome in the case of antibiotic-resistant pathogens, which constitute a growing threat to human health worldwide and require new preventative routes of disinfection. In this study, we have incorporated different loading levels of a porphyrin photosensitizer capable of generating reactive singlet oxygen in the presence of O₂ and visible light in a water-soluble, photo-cross-linkable polymer coating, which was subsequently deposited on polymer microfibers. Two different application methods are considered, and the morphological and chemical characteristics of these coated fibers are analyzed to detect the presence of the coating and photosensitizer. To discern the efficacy of the fibers against pathogenic bacteria, photodynamic inactivation has been performed on two different bacterial strains, Staphylococcus aureus and antibiotic-resistant Escherichia coli, with population reductions of >99.9999 and 99.6%, respectively, after exposure to visible light for 1 h. In response to the current COVID-19 pandemic, we also confirm that these coated fibers can inactivate a human common cold coronavirus serving as a surrogate for the SARS-CoV-2 virus.

Cellulose nanocrystals for gelation and percolation-induced reinforcement of a photocurable poly(vinyl alcohol) derivative

Nanomaterials are regularly added to crosslinkable polymers to enhance mechanical properties; however, important effects related to gelation behavior and crosslinking kinetics are often overlooked. In this study, we combine cellulose nanocrystals (CNCs) with a photoactive poly(vinyl alcohol) derivative, PVA-SbQ, to form photocrosslinked nanocomposite hydrogels. We investigate the rheology of PVA-SbQ with and without CNCs to decipher the role of each component in final property development and identify a critical CNC concentration (1.5 wt%) above which several changes in rheological behavior are observed. Neat PVA-SbQ solutions exhibit Newtonian flow behavior across all concentrations, while CNC dispersions are shear-thinning <6 wt% and gel at high concentrations. Combining semi-dilute entangled PVA-SbQ (6 wt%) with >1.5 wt% CNCs forms a percolated microstructure. In situ photocrosslinking experiments reveal how CNCs affect both the gelation kinetics and storage modulus (G') of the resulting hydrogels. The modulus crossover time increases after addition of up to 1.5 wt% CNCs, while no modulus crossover is observed >1.5 wt% CNCs. A sharp increase in G' is observed >1.5 wt% CNCs for fully-crosslinked networks due to favorable PVA-SbQ/CNC interactions. A percolation model is fitted to the G' data to confirm that mechanical percolation is maintained after photocrosslinking. A ∼120% increase in G' for 2.5 wt% CNCs (relative to neat PVA-SbQ) confirms that CNCs provide a reinforcing effect through the percolated microstructure formed from PVA-SbQ/CNC interactions. The results are testament to the ability of CNCs to significantly alter the storage moduli of crosslinked polymer gels at low loading fractions through percolation-induced reinforcement.

Scaling Resistance in Nanophotonics-Enabled Solar Membrane Distillation

This study compares the scaling behavior of membrane distillation (MD) with that of nanophotonics-enabled solar membrane distillation (NESMD). Previous research has shown that NESMD, due to its localized surface heating driven by photothermal membrane coatings, is an energy-efficient system for off-grid desalination; however, concerns remained regarding the scaling behavior of self-heating surfaces. In this work, bench-scale experiments were performed, using model brackish water, to compare the scaling propensity of NESMD with MD. The results showed NESMD to be highly resistant to scaling; a three times higher salt concentration factor (c/c₀) was achieved in NESMD compared to MD without any decline in flux. Analyses of the scaling layer on NESMD membranes revealed that salt deposition was 1/4 of that observed for MD. Scaling resistance in NESMD is attributed to its lower operating temperature, which increases the solubility of common scalants and decreases salt precipitation rates. Precipitation kinetics measurements revealed an order of magnitude faster precipitation under heated conditions (62 °C, k = 8.7 × 10^-2 s^-1) compared to ambient temperature (22 °C, k = 7.1 × 10^-3 s^-1). These results demonstrate a distinct advantage of NESMD over MD for the treatment of high scaling potential water, where scaling is a barrier to high water recovery.

A review on versatile applications of blends and composites of CNC with natural and synthetic polymers with mathematical modeling

Cellulose is world's most abundant, renewable and recyclable polysaccharide on earth. Cellulose is composed of both amorphous and crystalline regions. Cellulose nanocrystals (CNCs) are extracted from crystalline region of cellulose. The most attractive feature of CNC is that it can be used as nanofiller to reinforce several synthetic and natural polymers. In this article, a comprehensive overview of modification of several natural and synthetic polymers using CNCs as reinforcer in respective polymer matrix is given. The immense activities of CNCs are successfully utilized to enhance the mechanical properties and to broaden the field of application of respective polymer. All the technical scientific issues have been discussed highlighting the recent advancement in biomedical and packaging field.

Graphene Oxide Filled Lignin/Starch Polymer Bionanocomposite: Structural, Physical, and Mechanical Studies

In this study, graphene oxide (GO) was investigated as a potential nanoreinforcing agent in starch/lignin (ST/L) biopolymer matrix. Bionanocomposite films based on ST/L blend matrix and GO were prepared by solution-casting technique of the corresponding film-forming solution. The structures, morphologies, and properties of bionanocomposite films were characterized by Fourier transform infrared (FTIR), thermal gravimetric analysis (TGA), ultraviolet-visible (UV-vis), SEM, and tensile tests. The experimental results showed that content of GO have a significant influence on the mechanical properties of the produced films. The results revealed that the interfacial interaction formed in the bionanocomposite films improved the compatibility between GO fillers and ST/L matrix. The addition of GO also reduced moisture uptake (Mu) and water vapor permeability of ST/L blend film. In addition, TGA showed that the thermal stability of bionanocomposite films was better than that of neat starch film. These findings confirmed the effectiveness of the proposed approach to produce biodegradable films with enhanced properties, which may be used in packaging applications.

One Step Synthesis of Uniform SnO2 Electrode by UV Curing Technology toward Enhanced Lithium-Ion Storage

A uniform anode material composed of ultrasmall tin oxide (SnO₂) nanoparticles with an excellent lithium-ion (Li-ion) storage performance is obtained for the first time through one step UV curing technology. The diameter of ∼3 nm-sized SnO₂ particles is uniformly dispersed in the styrylpyridinium (SbQ) polymer because of its photo-cross-linking property. The in situ cross-linking of SbQ polymer not only assist synthesis of uniform ultrasmall SnO₂, but act as a strong adhesion binder on SnO₂ nanoparticles, thereby effectively accommodating the volume expansion of SnO₂ anodes during cycling process. The uniform electrode exhibits substantially higher specific capacity and longer cycling stability compared with the SnO₂ nanoparticles electrodes treated by traditional PVDF-mixing method. A stable specific capacity of 572.5 mA h g^-1 of the SnO₂ electrode derived from UV curing technology is obtained at a current density of 0.2 C (156.2 mA g^-1) after 150 cycles. Even at high rate of 5 C (3905 mA g^-1), the electrode still demonstrates specific capacity of 440.2 mA h g^-1. Therefore, the scalable and low-cost synthetic approach described herein can readily be extended to other nanomaterials electrodes to improve their lithium-storage properties.

Design and evaluation of mucoadhesive oral films containing sodium hyaluronate using multivariate data analysis

CONTEXT

Mucoadhesive oral films, with their prolonged residence time at the site of application, offer a promising approach for protection of the oral lesion surface. The addition of sodium hyaluronate of different molecular weights as a second mucoadhesive polymer into the film matrix could positively influence the physico-mechanical and mucoadhesive properties of films.

OBJECTIVE

The aim of this study was to investigate the formulation of a monolayered film matrix containing varying amounts of sodium hyaluronate and to test the properties of such matrices by applying different characterization methods.

MATERIALS AND METHODS

Film matrix was composed of two mucoadhesive polymers, carmellose sodium and sodium hyaluronate, plasticized with glycerol. Resulting films were characterized with regard to their viscosity and physico-mechanical properties.

RESULTS AND DISCUSSION

Multivariate data analysis was employed to evaluate the influence of varying amounts of mucoadhesive polymers on the main mucoadhesive oral films' properties. The lower content of sodium hyaluronate caused improvements in mechanical properties and residence time on the artificial oral mucosa, both of which are the main characteristics that determine the quality of the final product.

CONCLUSIONS

The best results were obtained by samples containing carmellose sodium with a small amount of sodium hyaluronate (about 0.5% in casting dispersion).