Preparation of cotton-based fibrous adsorbents for the removal of heavy metal ions

Influence of agro-wastes derived biochar and their composite on reducing the mobility of toxic heavy metals and their bioavailability in industrial contaminated soils

The agro-waste derived valuable products are prime interest for effective management of toxic heavy metals (THMs). The present study investigated the efficacy of biochars (BCs) on immobilization of THMs (Cr, Zn, Pb, Cu, Ni and Cd), bioaccumulation and health risk. Agro-wastes derived BCs including wheat straw biochar (WSB), orange peel biochar (OPB), rice husk biochar (RHB) and their composite biochar (CB) were applied in industrial contaminated soil (ICS) at 1% and 3% amendments rates. All the BCs significantly decreased the bioavailable THMs and significantly (p < 0.001) reduced bioaccumulation at 3% application with highest efficiency for CB followed by OPB, WSB and RHB as compared to control treatment. The bioaccumulation factor (BAF), concentration index (CI) and ecological risk were decreased with all BCs. The hazard quotient (HQ) and hazard index (HI) of all THMs were <1, except Cd, while carcer risk (CR) and total cancer risk index (TCRI) were decreased through all BCs. The overall results depicted that CB at 3% application rate showed higher efficacy to reduce significantly (p < 0.001) the THMs uptake and reduced health risk. Hence, the present study suggests that the composite of BCs prepared from agro-wastes is eco-friendly amendment to reduce THMs in ICS and minimize its subsequent uptake in vegetables.

Immature persimmon residue as a novel biosorbent for efficient removal of Pb(II) and Cr(VI) from wastewater: Performance and mechanisms

Owing to the powerful affinity of tannin toward heavy metal ions, it is frequently immobilized on adsorbents to enhance their adsorption properties. However, natural adsorbents containing tannin have been overlooked owing to its water solubility. Herein, a novel natural adsorbent based on the immature persimmon residue (IPR) with soluble tannin removed was fabricated to eliminate Pb(II) and Cr(VI) in aquatic environments. The insoluble tannin in IPR endowed it with prosperous properties for eliminating Pb(II) and Cr(VI), and the IPR achieved maximum Pb(II) and Cr(VI) adsorption quantities of 68.79 mg/g and 139.40 mg/g, respectively. Kinetics and isothermal adsorption analysis demonstrated that the removal behavior was controlled by monolayer chemical adsorption. Moreover, the IPR exhibited satisfactory Pb(II) and Cr(VI) removal efficiencies even in the presence of multiple coexisting ions and showed promising regeneration potential after undergoing five consecutive cycles. Additionally, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) analysis unveiled that the elimination mechanisms were primarily electrostatic attraction, chelation and reduction. Overall, the IPR, as a tannin-containing biosorbent, was verified to possess substantial potential for heavy metal removal, which can provide new insights into the development of novel natural adsorbents from the perspective of waste resource utilization.

In Situ Synthesis of NH2-MIL-53-Al/PAN Nanofibers for Removal Co(II) through an Electrospinning Process

In this study, researchers developed a novel composite material called NH2-MIL-53-Al/PAN, which consists of metal-organic frameworks (MOFs) grown on electrospun PAN nanofibers (NFs). The successful formation of the composite was confirmed by X-ray diffraction (XRD) and Fourier transform infrared (FTIR), and the hydrophilicity of NH2-MIL-53-Al/PAN was demonstrated by the water contact angle (WCA). Batch experiments were conducted to investigate the adsorption performance of Co(II) under different conditions. The maximum adsorption capacity reached 58.72 mg/g, and almost 95% of the adsorption was achieved within the first 6 h. The adsorption process was found to be spontaneous and endothermic and followed the pseudo-second-order kinetics and Langmuir models. Chemisorption and molecular layer adsorption are the main mechanisms of adsorption, and X-ray photoelectron spectroscopy (XPS) analysis further reveals that the interaction between the adsorbent and cobalt is a coordination interaction. In this study, NH2-MIL-53-Al was grown in situ on PAN to ensure effective loading of MOFs and prevent agglomeration during the NF mixing process. This approach successfully addressed the challenge of exposing active sites within the embedded MOF crystals. Additionally, it overcame the difficulty of recycling traditional MOF adsorbents. As a result, the exceptional performance of MOF NFs offers a promising solution for the efficient removal of cobalt-containing wastewater.

Removal of chromium from water using manganese (II, III) oxides coated sand: adsorption and transformation of Cr(VI) and Cr(III)

A manganese coated sand (MCS) sorbent containing manganese (II,III) oxides was developed for adsorption and transformation of chromium [Cr(VI) and Cr(III)] with potential application in flow-through permeable media adsorption filters. Characterization of the MCS sorbent using XRD and XPS showed that the oxides of manganese (II) and manganese (III) were present on the MCS sorbent surface. Adsorption of both Cr(VI) and Cr(III) onto the MCS sorbent occurred over a broad pH range from 3 to 10. Surface charge analysis of the MCS sorbent determined a pHPZC of 7.8, which may facilitate the uptake of both oxy-anionic Cr(VI) species and cationic Cr(III) species. Favorable adsorption of Cr(VI) and Cr(III) onto the MCS sorbent occurred according to the Langmuir and the Freundlich adsorption equations, with a higher adsorption capacity for Cr(III) than Cr(VI). Adsorption parameters from the Langmuir, the Freundlich and the Temkin adsorption equations showed a stronger binding of Cr(VI) than Cr(III). Adsorption of Cr(III) decreased with increasing calcium concentration while adsorption of Cr(VI) decreased with increasing concentration of common anions found in natural water in the following order: phosphate > sulfate> bicarbonate. Transformation of chromium occurred on the surface of the MCS sorbent due to the partial reduction of Cr(VI) and the partial oxidation of Cr(III), which may be attributed to the role of surface manganese (II,III) oxides as either reducing or oxidizing agents. The MCS sorbent is a recyclable and sustainable adsorbent for removal of chromium from water with an environmental impact comparable to ion-exchange technology.

Insights into the Applications of Natural Fibers to Metal Separation from Aqueous Solutions

There is a wide range of renewable materials with attractive prospects for the development of green technologies for the removal and recovery of metals from aqueous streams. A special category among them are natural fibers of biological origin, which combine remarkable biosorption properties with the adaptability of useful forms for cleanup and recycling purposes. To support the efficient exploitation of these advantages, this article reviews the current state of research on the potential and real applications of natural cellulosic and protein fibers as biosorbents for the sequestration of metals from aqueous solutions. The discussion on the scientific literature reports is made in sections that consider the classification and characterization of natural fibers and the analysis of performances of lignocellulosic biofibers and wool, silk, and human hair waste fibers to the metal uptake from diluted aqueous solutions. Finally, future research directions are recommended. Compared to other reviews, this work debates, systematizes, and correlates the available data on the metal biosorption on plant and protein biofibers, under non-competitive and competitive conditions, from synthetic, simulated, and real solutions, providing a deep insight into the biosorbents based on both types of eco-friendly fibers.

Photodynamic activity enhanced by in situ biosynthetic BC/CQDs@PCN-224 membranes through FRET strategy

Porphyrin-based metal organic frameworks (MOFs) with efficient bactericidal performance have increasingly attracted attention in photodynamic inactivation materials. However, low reactive oxygen species (ROS) yield and drug residue hazards of current porphyrin-MOFs materials lead to unsatisfactory clinical therapeutic effects. In this paper, carbon quantum dots (CQDs) were encapsulated into PCN-224, which enhanced the photodynamic activity of the MOFs through fluorescence resonance energy transfer (FRET) process. Singlet oxygen (¹O₂) detection confirmed that the photodynamic activity of CQDs-doped PCN-224 (CQDs@PCN-224) was enhanced than that of pristine PCN-224 under illumination. Furthermore, the CQDs@PCN-224 were firmly embedded into bacterial cellulose (BC) nanofibrous membranes by using an eco-friendly biosynthetic approach, efficiently preventing MOFs leakage during use. The results of bactericidal assays demonstrated that BC/CQDs@PCN-224 membrane with higher photodynamic activity causes more severe disruption to bacterial structure and possesses better antibacterial efficiency (>99.99 % reduction of both Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli O157:H7 within 30 min) than BC/PCN-224 membrane under visible light illumination (500 W, 15 cm height, λ ≥ 420 nm). In addition, the biosynthesized BC/CQDs@PCN-224 membrane showed good hemocompatibility and low cytotoxicity, revealing that the BC- and MOFs-based material with enhanced PDI efficiency and satisfying safety has great potential in medical fields.

Heavy metal stabilization remediation in polluted soils with stabilizing materials: a review

The remediation of soil contaminated by heavy metals has long been a concern of academics. This is due to the fact that heavy metals discharged into the environment as a result of natural and anthropogenic activities may have detrimental consequences for human health, the ecological environment, the economy, and society. Metal stabilization has received considerable attention and has shown to be a promising soil remediation option among the several techniques for the remediation of heavy metal-contaminated soils. This review discusses various stabilizing materials, including inorganic materials like clay minerals, phosphorus-containing materials, calcium silicon materials, metals, and metal oxides, as well as organic materials like manure, municipal solid waste, and biochar, for the remediation of heavy metal-contaminated soils. Through diverse remediation processes such as adsorption, complexation, precipitation, and redox reactions, these additives efficiently limit the biological effectiveness of heavy metals in soils. It should also be emphasized that the effectiveness of metal stabilization is influenced by soil pH, organic matter content, amendment type and dosage, heavy metal species and contamination level, and plant variety. Furthermore, a comprehensive overview of the methods for evaluating the effectiveness of heavy metal stabilization based on soil physicochemical properties, heavy metal morphology, and bioactivity has also been provided. At the same time, it is critical to assess the stability and timeliness of the heavy metals' long-term remedial effect. Finally, the priority should be on developing novel, efficient, environmentally friendly, and economically feasible stabilizing agents, as well as establishing a systematic assessment method and criteria for analyzing their long-term effects.

Intensification of thorium biosorption onto protonated orange peel using the response surface methodology

In this research work, intensifying the possibility of protonated orange peel to uptake thorium (IV) ions from aqueous solutions in a batch system was investigated and optimized using the response surface methodology. The effect of three independent process variables including thorium initial concentration, pH, and biosorbent dosage was assessed based on the central composite design. The validity of the quadratic model was verified by the coefficient of determination. The optimization results showed that the rate of thorium (IV) uptake under optimal conditions is 183.95 mg/g. The modeling results showed that the experimental data of thorium biosorption kinetics are fitted well by the pseudo-second-order model. According to the results, the biosorption process reached equilibrium after around 4 h of contact. The Langmuir isotherm describes the experimental biosorption equilibrium data well. The maximum absorption capacity of protonated orange peel for thorium adsorption was estimated by the Langmuir isotherm at 236.97 mg/g. Thermodynamic studies show that thorium adsorption on protonated orange peel is thermodynamically feasible, spontaneous, and endothermic.

Efficient adsorption of heavy metals from wastewater on nanocomposite beads prepared by chitosan and paper sludge

Chitosan was commonly used with inorganic salt and organic compounds to prepare adsorption material for water treatment. Different materials were mixed for the preparation, leading to a high cost for water treatment. Sludge from papermaking has abundant fiber and inorganic salt, which can reduce the addition of raw materials in preparing the adsorption material and thus lower the cost. This work used recycled industrial paper sludge to prepare adsorption material to remove heavy metals from wastewater. The adsorption properties of the prepared sludge-chitosan material for Cu²⁺ and Cr³⁺ in wastewater were investigated. The impacts of adsorption time, pH, and initial concentrations of Cu²⁺ and Cr³⁺ on adsorption amount were studied and optimized. The saturated adsorption capacity of sludge-chitosan material for Cu²⁺ and Cr³⁺ can reach 114.6 and 110.3 mg/g. The adsorption kinetics satisfied the pseudo-second-order model, indicating two modes, physical diffusion, and chem-sorption, in the heavy metal adsorption by the sludge-chitosan materials. Physical distribution has little Effect on chemical adsorption. The materials can be applied to treating Cu²⁺ and Cr³⁺ containing wastewater with the proposed cheap and readily available sludge-chitosan material. The results confirmed that sludge-chitosan material possessed good regeneration performance and was an ideal adsorbent.

Aerogel Assembled by Two Types of Carbon Nanoparticles for Efficient Removal of Heavy Metal Ions

Both sodium alginate and polyethyleneimine (PEI) have a good ability to adsorb heavy metal ions. PEI and sodium alginate were used as important precursors to synthesize positively charged carbon nanoparticles (p-CNDs) with hydroxyl and carboxyl, and negatively charged carbon nanoparticles (n-CNDs) with amino, respectively. The carbon nanoparticles (CNDs) aerogel with a large specific surface area and rich functional groups were constructed by self-assembled p-CNDs and n-CNDs via electrostatic attraction for adsorption of heavy metal ions in water. The results show that CNDs aerogel has good adsorption properties for Pb²⁺ (96%), Cu²⁺ (91%), Co²⁺ (86%), Ni²⁺ (82%), and Cd²⁺ (78%). Furthermore, the fluorescence emission intensity of CNDs aerogel will gradually decrease with the increase in the adsorption rate, indicating that it can detect the adsorption process synchronously. In addition, the cytotoxicity test reveals that CNDs have good biocompatibility and will not cause secondary damage to biological cells.

Functionalized cotton charcoal/chitosan biomass-based hydrogel for capturing Pb2+, Cu2+ and MB

In this work, a porous multi-functional biomass carbon was prepared by acid-base modification method, which realized the reuse of waste cotton material. Then, the modified biochar was combined with the acrylic-based hydrogel by radical polymerization, and the biochar acrylic-based hydrogel (CS/EDTA/CBC) composite with chitosan and ethylenediamine tetraacetic acid was successfully prepared. This not only increases the adsorption performance of the adsorbent but also improves the stability of hydrogel. These characteristics provide high-efficiency adsorption capacity for pollutants (1105.78 mg g^-1 for Pb²⁺, 678.04 mg g^-1 for Cu²⁺, and 590.72 mg g^-1 for methylene blue (MB)), which is far superior to most reported adsorbents. Meanwhile, the adsorbent would have a strong chemical interaction with Pb²⁺ and Cu²⁺, can form a stable chelating structure, and showed stronger selective adsorption. The adsorption process is more suitable for the Langmuir isotherm and follows a pseudo-second-order kinetic model, which indicates that the adsorption is a single-layer adsorption, and the rate-limiting step is a chemical chelation reaction. XPS results confirmed that surface complexation and electrostatic attraction are the main mechanisms of the adsorption reaction. After five cycles, the adsorption capacity of the adsorbent and the recovery of heavy metal ions remained at a high level.

Functionalized Activated Carbon Fibers by Hydrogen Peroxide and Polydopamine for Efficient Trace Lead Removal from Drinking Water

To achieve efficient and selective trace heavy metals removal from drinking water, a low-cost purification material polydopamine/activated carbon fibers (PDA/H-ACF) was successfully prepared by polymerizing dopamine on the surface of activated carbon fibers pretreated with hydrogen peroxide. The morphology, phase, surface functional groups, specific surface, and pore size distribution of the as-prepared sample were analyzed using FESEM, XPS, BET and pore size distribution test (PST), and FTIR, and orthogonal experiments were used to investigate the influences of concentration of H₂O₂, pretreatment time, and reflux temperature on trace lead removal. The results showed that the sample pretreated under optimized conditions could produce different pore structures, and the content of functional group -COOH obviously increased. After further modification by polydopamine, the contents of -NH-, -NH₂, and -OH functional groups on the surface obviously enhanced, which were beneficial to increase adsorption site and promote trace lead removal. The effluent lead concentration decreased from initial 150 to 3.18 ppb within 5 min, meeting the requirement of NSF International Standard/American National Standard for Drinking Water Treatment Units (NSF/ANSI 53-2020) (5 ppb). The isothermal adsorption process and adsorption kinetics could be well-fitted by the Langmuir isotherm and pseudo-second-order kinetics model, indicating that the adsorption process of trace lead by PDA/H-ACF belonged to monolayer and chemical adsorption. Moreover, the as-prepared PDA/H-ACF also showed superior trace lead adsorption performance in the presence of high concentration competitive metal ions, in a wide pH range and in tap water, and therefore had good application prospect in the field of drinking water purification.

A novel surface imprinted resin for the selective removal of metal-complexed dyes from aqueous solution in batch experiments: ACB GGN as a representative contaminant

Metal-complexed dyes are harmful to the environment and human health because they contain heavy metals and complex organic ligands. It is difficult to separate and recover these dyes from wastewater owing to their complex components and poor selectivity of common adsorbents. In this study, a novel surface molecularly imprinted polymer (SMIP) was prepared using 4-vinyl pyridine as the functional monomer and polystyrene resin as the carrier. SMIP showed better adsorption performance than non-imprinted polymer (SNIP) in the whole pH range with the best adsorption capacity at pH 1.5. The correlation coefficients (R²) fitted by Langmuir and Temkin models were greater than 0.97, and the adsorption was a spontaneous exothermic process. The pseudo-second-order and Elovich models fitted the adsorption kinetic curves well. The adsorption capacity of SMIP was approximately 20% higher than that of SNIP in the salt concentration ranging from 2 to 80 mg/L. In selective adsorption experiments, the relative selectivity coefficients (I) of SMIP for competitors were all greater than 2.41, and the Cr (Ⅲ) components of ACB GGN played a more important role in the recognition performance of SMIP than the sulfonic groups. Adsorption mechanism tests revealed that although the adsorption of ACB GGN by SMIP mainly relied on electrostatic attraction, hydrophobic interactions, π-π conjugation, and Cr (Ⅲ) coordination were also involved. These results show that SMIP has excellent selective adsorption properties for ACB GGN and a promising application potential in the treatment of metal-complexed dye wastewater.

Light-driven self-disinfecting textiles functionalized by PCN-224 and Ag nanoparticles

Toward the goal of preventing microbial infections in hospitals or other healthcare institutions, here we developed a self-disinfecting textile with synergistic photodynamic/photothermal antibacterial property. Porphyrinic Metal-organic frameworks (PCN-224) and Ag nanoparticles (NPs) were in situ grown on knitted cotton textile (KCT) successively to achieve rapid photodynamic antibacterial and durable bacteriostatic effect. Light-driven singlet oxygen (¹O₂) generated from PCN-224 and heat generated from Ag could function synergistically to realize rapid bacterial inactivation. Interestingly, ¹O₂ could promote Ag NPs to be degraded to release more Ag⁺ ions, achieving durable bacteriostatic effect. Antibacterial assay demonstrated 6 and 4.49 log unit inactivation toward two typical bacterial strains (E. coli and S. aureus) under Xe arc lamp in 30 min, respectively. Even after ten washes, the textile still maintained 6 log unit bacterial inactivation. Mechanism study proved light-driven ¹O₂ and heat are main factors causing bacterial inactivation, they could work synergistically to enhance bacterial inactivation efficiency. Photothermal study revealed that the textile could reach to 69 ℃ under visible light and 79.1 ℃ under 780-nm light-laser, which showed much potential in photothermal material applications. Taken together, our findings demonstrated a synergistic self-disinfecting cotton textile that exhibited constructive significance for preventing microbial infections and transmissions.

P. S. AK, Oyekanmi AA, Gideon ON, Abdullah CK, Yahya EB, Alfatah T, Sabaruddin FA, Rahman AA. Cotton Wastes Functionalized Biomaterials from Micro to Nano: A Cleaner Approach for a Sustainable Environmental Application

The exponential increase in textile cotton wastes generation and the ineffective processing mechanism to mitigate its environmental impact by developing functional materials with unique properties for geotechnical applications, wastewater, packaging, and biomedical engineering have become emerging global concerns among researchers. A comprehensive study of a processed cotton fibres isolation technique and their applications are highlighted in this review. Surface modification of cotton wastes fibre increases the adsorption of dyes and heavy metals removal from wastewater. Cotton wastes fibres have demonstrated high adsorption capacity for the removal of recalcitrant pollutants in wastewater. Cotton wastes fibres have found remarkable application in slope amendments, reinforcement of expansive soils and building materials, and a proven source for isolation of cellulose nanocrystals (CNCs). Several research work on the use of cotton waste for functional application rather than disposal has been done. However, no review study has discussed the potentials of cotton wastes from source (Micro-Nano) to application. This review critically analyses novel isolation techniques of CNC from cotton wastes with an in-depth study of a parameter variation effect on their yield. Different pretreatment techniques and efficiency were discussed. From the analysis, chemical pretreatment is considered the most efficient extraction of CNCs from cotton wastes. The pretreatment strategies can suffer variation in process conditions, resulting in distortion in the extracted cellulose's crystallinity. Acid hydrolysis using sulfuric acid is the most used extraction process for cotton wastes-based CNC. A combined pretreatment process, such as sonication and hydrolysis, increases the crystallinity of cotton-based CNCs. The improvement of the reinforced matrix interface of textile fibres is required for improved packaging and biomedical applications for the sustainability of cotton-based CNCs.

Molecular dissolved organic matter removal by cotton-based adsorbents and characterization using high-resolution mass spectrometry

This research investigates the characteristics of dissolved organic matter (DOM) removal by synthesized cotton-fiber adsorbents using unknown screening analysis with high resolution and accurate mass spectrometry. Molecular characteristics of DOM removed by adsorbents were investigated semiquantitatively and unknown disinfection byproduct (DBP) formation potentials were also investigated. Adsorbents were modified using ferric nitrate to increase the magnetic property. The XRD pattern showed Fe-containing crystalline structures in the modified adsorbent (M-CF). The M-CF possessed higher mesopore volume, which enhanced the dissolved organic carbon (DOC) removal efficiency to 74.50% (compared to 32.12% in the unmodified CF adsorbent). The kinetics experiment showed that both adsorbents were better fitted to pseudo-second orders than pseudo-first orders. The initial rate constant was higher in M-CF (1.40 mg/g min) than in CF (0.02 mg/g min) treatments due to the higher mesopore volume in M-CF. M-CF removed almost 700 carbon‑hydrogen‑oxygen based DOMs (CHO features), 300 more CHO features than CF. CF selectively adsorbed only higher-molecular-weight (MW) CHO features (more CH₂ groups), while the mesopores in M-CF removed DOM with lower MW (fewer CH₂ groups) that were refractory to CF. The low MW DOM removed only by M-CF mesopore exhibited more oxidized (positive carbon oxidation state, C_os) and saturated characters (negative oxygen-subtracted double bond equivalent per carbon, (DBE-O)/C). After chlorination, over 50 unknown DBPs were detected, 33 of which were commonly found in all samples. M-CF decreased unknown formation potential more than CF. However, adsorption of M-CF and CF before chlorination resulted in different remaining precursors to water chlorination and formed unique DBPs from those precursors.

A novel effect of combining microorganisms and graphene oxide for solidifying simulated nuclides strontium

Inspired by microbial diagenesis and mounding, microbial mineralization technology has been widely used in the treatment of heavy metal and radionuclide contamination. S. pasteurii can decompose urea as a source of energy to produce CO₃^2- in the microbial mineralization system. Therefore, strontium-contaminated radioactive wastewater can be effectively treated by combining CO₃^2- with surrounding strontium ions (Sr²⁺) to form strontium carbonate (SrCO₃). Herein, we investigated how the concentration of graphene oxide (GO) and mineralization time influence the morphology of SrCO₃ and the mineralization efficiency. GO was used as a crystal regulator to solidify the radionuclide strontium in the microbial mineralization system to obtain large-scale rock-like SrCO₃ minerals. The results showed that GO can adsorb the surrounding Sr²⁺ with oxygen-containing functional groups on its surface to form SrCO₃ complexes, directly influencing the morphology and consolidation percentage of SrCO₃. Considering the leaching behaviour of nuclides, we further studied the stability of consolidated SrCO₃ minerals. The results indicated that the presence of GO improved the stability of the mineralized samples obtained in the microbial mineralization system.

Smart Textiles with Self-Disinfection and Photothermochromic Effects

Self-disinfecting textile materials employing combined photodynamic/photothermal effects enable the prevention of microbial infections, a property that has great potential in healthcare applications. However, smart textiles with stimulus responses to ambient temperature are marvelous materials for enhancing their photothermal applications with additional functions. It is still challenging to realize vivid and contrasting color changes as temperature indicators. Herein, through the in situ growth of PCN-224 metal-organic frameworks (MOFs), the electrospraying of a Ti₃C₂ MXene colloid, and the screen printing of a thermochromic dye, a smart photothermochromic self-disinfecting textile has been fabricated. An antibacterial inactivation study revealed 99.9999% inactivation toward gram-negative (Escherichia coli ATCC 8099) and gram-positive (Staphylococcus aureus ATCC 6538) bacteria in 30 min. A mechanism study revealed that light-driven singlet oxygen and heat are the main reasons for bacterial inactivation. Interestingly, the fabrics presented photothermal effects not only under a handheld 780 nm NIR laser but also under visible Xe lamp (λ ≥ 420 nm) illumination. The color of the fabrics (S-CF@PCN_0.08) changed completely from dark green to dark red when the temperature exceeded 45 °C under Xe lamp illumination. Furthermore, the photothermochromic effect occurred in just 1 s under a 780 nm laser. Taken together, this smart photothermochromic self-disinfecting textile permits a new way to feedback the timely signal of temperature by color change and provides novel insights into the development of self-disinfecting textiles.

Efficient removal of Pb(ii) and Cr(vi) from acidic wastewater using porous thiophosphoryl polyethyleneimine

A porous thiophosphoryl polyethyleneimine was synthesized to remove Pb(ii) and Cr(vi) from acidic wastewater.

Adsorption of Cu(ii) from solution by modified magnetic starch St/Fe3O4-g-p(AA-r-HEMA)

Magnetic starch was prepared, and then AA and HEMA were grafted on its surface to obtain St/Fe3O4-g-p(AA-r-HEMA) for the adsorption of Cu(ii).

Aminophosphonic Acid Functionalized Cellulose Nanofibers for Efficient Extraction of Trace Metal Ions

Cellulose nanofibers were covalently functionalized using diethylenetriamine penta (methylene phosphonic acid) and studied for the extraction of heavy metal ions. The surface-functionalized nanofibers showed a high adsorption capacity towards heavy metal ions as compared to bare nanofibers. The elemental composition and surface morphology of the prepared bio-adsorbent was characterized by X-ray photoelectron spectroscopy, attenuated total reflectance infrared spectroscopy, field emission scanning electron microscopy, and energy dispersive spectroscopy. The prepared material was studied to develop a column-based solid phase extraction method for the preconcentration of trace metal ions and their determination by inductively coupled plasma optical emission spectroscopy. The batch experimental data was well fitted to Langmuir adsorption isotherms (R2 > 0.99) and follows pseudo-second-order kinetics. The experimental variables such as sample pH, equilibrium time, column breakthrough, sorption flow rate, the effect of coexisting ions, and eluent type were systematically studied and optimized accordingly. The detection limit of the proposed method was found to be 0.03, 0.05, and 0.04 µg L-1 for Cu(II), Pb(II), and Cd(II), respectively. Certified Reference Materials were analyzed to validate the proposed method against systematic and constant errors. At a 95% confidence level, the Student's t-test values were less than the critical Student's t value (4.302). The developed method was successfully employed for the preconcentration and determination of trace metal ions from real water samples such as river water and industrial effluent.

Application of waste cotton yarn as adsorbent of heavy metal ions from single and mixed solutions

In this study, waste cotton yarn was used for the removal of Pb (II), Cd (II), Cr (III), and As (V) from aqueous solution. Adsorption of heavy metal ions was tested from single ion solutions, while competitive studies were performed using two- and four-ion mixtures. In order to change the structure of the material, cotton yarn was modified by sodium hydroxide solution. The surface of raw and modified cotton yarn were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, and streaming potential method for determination of an isoelectric point. Sorption studies were performed on the basis of pH, kinetics, isotherms, and desorption results. It has been shown that waste cotton yarn modification, typically, does not improve the sorption capacity of the material and that the unmodified material could be used for the removal of examined heavy metal ions. Selectivity was in order Pb > Cd > Cr > As. Desorption studies have indicated to the possible reusability of the sorbent only in the case of Pb removal. A potential application of spent waste sorbent for the soil quality improvement has been considered.

A stiff ZnO/carbon foam composite with second-level macroporous structure filled ZnO particles for heavy metal ions removal

A stiff zinc oxide/carbon foam (ZnO/CF) composite as a desirable adsorbent for heavy metal ions was innovatively designed and fabricated by loading ZnO particles into a carbon foam with capsule-like second-level macropores. The features of the resulting composite were characterized by FESEM, XRD, BET, FTIR, and XPS. The effects of adsorption parameters on the Pb(II), Cr(III), and Cu(II) ions removal were studied through batch experiments. Results show that the ZnO/CF composite possesses a second-level macroporous structure filled ZnO particles, which has both mesoporous structure and Zn-O-C bond with the strongly synergistic effect. And meanwhile, it has a relatively high compression strength of 2.18 MPa at a density of 0.18 g cm^-3. The experimental maximum adsorption capacities for Pb(II), Cr(III), and Cu(II) ions reach 170.85 mg g^-1, 168.74 mg g^-1, and 104.61 mg g^-1 with relatively high partition coefficients of 5.803 mg g^-1 μM^-1, 1.169 mg g^-1 μM^-1, and 0.648 mg g^-1 μM^-1, respectively. The experimental data are in accordance with Langmuir isotherm and pseudo-second-order kinetic model. Moreover, the composite still exhibits a good adsorption performance even after five cycles.

Reusable Magnetic Nanoparticle Immobilized Nitrogen-Containing Ligand for Classified and Easy Recovery of Heavy Metal Ions

Functionalized Tris[2-(dimethylamino) ethyl] amine (Me₆TREN) ligands tethered-Fe₃O₄@Me₆TREN nanoparticles (NPs) with a size of 150 nm were prepared to achieve classified and easy recovery of heavy metal ions in wastewater. The preparation of such NPs related to sequential silane ligand exchange and a following cure and Schiff base reactions for Fe₃O₄ NPs. Fe₃O₄@Me₆TREN NPs as an effective nano-adsorbent of heavy metals exhibited significant differences in maximum adsorption capacity for Cr(III) (61.4 mg/g), Cu(II) (245.0 mg/g), Pb(II) (5.3 mg/g), and Cd(II) (1136.2 mg/g), in favor of classified removal of heavy metals from wastewater. Furthermore, Fe₃O₄@Me₆TREN NPs can be regenerated by desorbing metal ions from NP surfaces eluted with ethylenediaminetetraacetic acid disodium salt (EDTA-Na₂) aqueous, which endows such NPs promising potency as new nano-vectors for the removal of heavy metals.