A biaxially stretched cellulose film prepared from ionic liquid solution

Structuring restricted amorphous molecular chains in the reinforced cellulose film by uniaxial stretching

The construction of the preferred orientation structure by stretching is an efficient strategy to fabricate high-performance cellulose film and it is still an open issue whether crystalline structure or amorphous molecular chain is the key factor in determining the enhanced mechanical performance. Herein, uniaxial stretching with constant width followed by drying in a stretching state was carried out to cellulose hydrogels with physical and chemical double cross-linking networks, achieving high-performance regenerated cellulose films (RCFs) with an impressive tensile strength of 154.5 MPa and an elastic modulus of 5.4 GPa. The hierarchical structure of RCFs during uniaxial stretching and drying was systematically characterized from micro- to nanoscale, including microscopic morphology, crystalline structure as well as relaxation behavior at a molecular level. The two-dimensional correlation spectra of dynamic mechanical analysis and Havriliak-Negami fitting results verified that the enhanced mechanical properties of RCFs were mainly attributed to the stretch-induced tight packing and restricted relaxation of amorphous molecular chains. The new insight concerning the contribution of molecular chains in the amorphous region to the enhancement of mechanical performance for RCFs is expected to provide valuable guidance for designing and fabricating high-performance eco-friendly cellulose-based films.

A regenerated cellulose fiber with high mechanical properties for temperature-adaptive thermal management

The escalating global population has led to a surge in waste textiles, posing a significant challenge in landfill management worldwide. In this work, ionic liquid 1-butyl-3-methylimidazole acetate ([Bmim]OAc) and DMF (N, n-dimethylformamide) were used as solvents to dissolve waste denim fabric, then vanadium dioxide (VO2) nanoparticles were introduced into the spinning solution, and cellulose fibers were regenerated by dry-wet spinning process, to promote the recycling of waste cotton fabric. Finally, regenerated cellulose fibers with high added value were prepared by dry-wet spinning. Through this innovative strategy, on the one hand, because VO2 can form a large number of hydrogen bonds between the regenerated cellulose molecules, and realize the cross-networking structure of the molecular chains inside the fiber, the mechanical properties of the regenerated cellulose fibers are enhanced. On the other hand, due to the thermal phase transformation characteristics of VO2, it also endows the regenerated cellulose fiber unique intelligent temperature control function. Compared with the pristine regenerated fiber, the tensile stress of the regenerated fiber after adding VO2 nanoparticles (F-VO2) increased by 25.6 %, reaching 158.68 MPa. In addition, the F-VO2 fibric provides excellent intelligent temperature control, reducing temperatures by up to 6.7 °C.

Dissolving-co-catalytic strategy for the preparation of flexible and wet-stable cellulose membrane towards biodegradable packaging

In the realization of the goal of circular economy, cellulose as one of sustainable biomass resources, have attracted much attention because of their abundant sources, biodegradability and renewability. However, the mechanical and waterproof performance of cellulose-based materials are usually not satisfying, which limits their high-value utilization. In this study, cellulose membrane with high-performance from the aspects of mechanical properties, water-resistance ability, oxygen barrier capacity and biodegradability, was prepared from bleached hardwood pulp (HBKP) in a AlCl3/ZnCl2/H2O solution. The AlCl3/ZnCl2/H2O acted as both solvent and catalyst to dissolve cellulose and facilitate the chemical crosslinking of epichlorohydrin (EPI) with cellulose, thus improved the overall performance of the obtained cellulose membrane. The addition sequence, amount and crosslinking time of EPI during chemical crosslinking had important effects on the properties of the membranes. When 7 wt% EPI was crosslinked for 24 h, the tensile stress reached 133 MPa and the strain reached 17 %. Moreover, the membrane had excellent oxygen insulation down to (1.1 ± 0.31) × 10-4 cm3/m2·d·Pa, and good water-resistance ability, no obvious swelling behavior after 450 days of immersion in distilled water. Furthermore, the membrane could be degraded by microorganisms in about 20 days. This cellulose-based membrane offers a sustainable and biodegradable packaging material.

Advances in green solvents for production of polysaccharide-based packaging films: Insights of ionic liquids and deep eutectic solvents

The problems with plastic materials and the good film-forming properties of polysaccharides motivated research in the development of polysaccharide-based films. In the last 5 years, there has been an explosion of publications on using green solvents, including ionic liquids (ILs), and deep eutectic solvents (DESs) as candidates to substitute the conventional solvents/plasticizers for preparations of desired polysaccharide-based films. This review summarizes related properties and recovery of ILs and DESs, a series of green preparation strategies (including pretreatment solvents/reaction media, ILs/DESs as components, extraction solvents of bioactive compounds added into films), and inherent properties of polysaccharide-based films with/without ILs and DESs. Major reported advantages of these new solvents are high dissolving capacity of certain ILs/DESs for polysaccharides (i.e., up to 30 wt% for cellulose) and better plasticizing ability than traditional plasticizers. In addition, they frequently display intrinsic antioxidant and antibacterial activities that facilitate ILs/DESs applications in the processing of polysaccharide-based films (especially active food packaging films). ILs/DESs in the film could also be further recycled by water or ethanol/methanol treatment followed by drying/evaporation. One particularly promising approach is to use bioactive cholinium-based ILs and DESs with good safety and plasticizing ability to improve the functional properties of prepared films. Whole extracts by ILs/DESs from various byproducts can also be directly used in films without separation/polishing of compounds from the extracting agents. Scaling-up, including costs and environmental footprint, as well as the safety and applications in real foods of polysaccharide-based film with ILs/DESs (extracts) deserves more studies.

Progress, Challenge and Perspective of Fabricating Cellulose

Cellulose as the most abundant biopolymers on Earth, presents appealing performance in mechanical properties, thermal management, and versatile functionalization. The development of fabrication methods closely relates to enrich its functionality and reduce manufacture cost. However, cellulose is hard to be dissolved by most common solvents or melt due to its recalcitrant property. Herein, the recent progress of fabricating cellulose is summarized. First, the unique hierarchical structure of cellulose is fully investigated and the resulted processability is highlighted in directions of down to nanocellulose, dissolution, and thermoplastic processing. Then, the reported fabrication methods are summarized in three aspects: (1) self-assembly from nano/micro cellulose suspensions, especially the self-assembly of cellulose nanocrystals; (2) dissolution-regeneration-drying, covering spinning and solvent infusion processing; and (3) thermoplastic processing, focusing on analysis of the setup and the morphology changes of the prepared products. In each aspect, the flowchart of the fabrication process, the behind mechanism, fabricated products, and effects of processing parameters are explored. Finally, this review provides a perspective on the further direction of fabricating cellulose, especially the challenges toward mass production of cellulose. This article is protected by copyright. All rights reserved.

A Systematic Review of New Trends in Ionic Liquids Applied to Electrolytes on Polysaccharides

Polysaccharides are formed by a long chain of monosaccharides, with the main function of promoting energetic and structural reserves for plants and animals. They can be applied as a base of electrolytes, using ionic liquids (ILs) as a solvent base. The study of electrolytes is an emerging field, as they are applied as secondary batteries, fuel cells, solar cells, supercapacitors and chemical sensors. They operate stably under extreme conditions, maintaining their high thermal stability. Furthermore, their low cost and environmentally safe character, compared to conventional electrolytes, have attracted considerable attention in the scientific field. ILs are composed entirely of ions and could be potentially applied as solvents. As electrolytes, ILs are environmentally friendly, and their use in combination with polysaccharides leads to a synergic effect. In the present study, a systematic review was performed of all papers published from 2014 to 2022 regarding ILs and polysaccharides through a search of three databases. Due to the large number of results found, only papers about electrolytes were considered and the main findings described. This study allows for easy identification of the most relevant fields of study with respect to ILs and polysaccharides, as well as the main gaps to be explored in the literature.

Anisotropic Alignment of Bacterial Nanocellulose Ionogels for Unconventionally High Combination of Stiffness and Damping

Ionogels are emerging materials for advanced electrochemical devices; however, their mechanical instability to external stresses has raised concerns about their safety. This study reports aligned bacterial nanocellulose (BC) ionogel films swelled with the model ionic liquid (IL) of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF₄) for an unprecedented combination of high stiffness and high energy dissipation without significant loss of ionic conductivity. The aligned BC ionogel films are prepared through wet-state stretching methods, followed by drying and swelling by ILs. The aligned ionogel films exhibit significantly improved dynamic mechanical properties, overcoming the mechanical conventional limit of traditional materials by 2.0 times at 25 °C and by a maximum of 4.0 times at 0 °C. Additionally, the same samples exhibit relatively high ionic conductivities of 0.16 mS cm^-1 at 20 °C and 0.45 mS cm^-1 at 60 °C with storage moduli over 10 GPa. The synergistic effect of the mechanical reinforcements by alignment of the BC nanofibers and the plasticizing effects by ILs could be attributed to the significant enhancement of dynamic mechanical properties and the retention of ionic conductivities. These results will lead to a deeper understanding of the material design for mechanically superior ionogel systems with increasing demands for advanced electronic and electrochemical devices.

Stretch-Induced Crystallization of Cellulose Spun from Ionic Liquid Solution

With the emergence of efficient green solvents, structural regulation of regenerated cellulose is highly desired in the solution process from an industrial perspective. Cellulose fiber and films are viewed as a "composite" comprising amorphous and crystalline fractions. The regulation of the crystalline structure is of great importance for the properties of cellulose materials. In this study, we found stretch-induced crystallization behavior during the transition from solution to gel via coagulation. The crystallinity index of the hydrogel fiber increases with the stretch ratio (SR). X-ray diffraction revealed that the cellulose II hydrate formed in the stretched hydrogel fibers. The mechanical properties and thermal stability of the dry fibers greatly improved against the SR. This crystallization behavior depends on the concentration of the solution and the type of ionic liquid. This stretch-induced crystallization provides an efficient method for structural regulation in cellulose solution processing.

High-tensile regenerated cellulose films enabled by unexpected enhancement of cellulose dissolution in cryogenic aqueous phosphoric acid

We have demonstrated, for the first time, high-efficient non-destructive and non-derivative dissolution of cellulose could be achieved in cryogenic aqueous phosphoric acid. Cellulose from different sources and of varying degree of polymerization from 200 (MCC) to 2200 (cotton fabric) could be dissolved completely to afford solutions containing 5 wt%-18 wt% cellulose, from which ultra-strong and tough cellulose films of tensile strength as high as 707 MPa could be obtained using water as the coagulant. These solutions can be stored at -18 °C for extended time without noticeable degradation while desired degree of polymerization is also attainable by tuning the storage conditions. The findings of this work call for renewal attention on phosphoric acid as a promising cellulose solvent for being non-toxic, non-volatile, easy to handle, and cost-effective.

Pyrolysis Kinetics of a Lignin-Modified Cellulose Composite Film

Cellulose is the most abundant natural biopolymer material, which has been widely used in film making and food packaging in recent years. However, lignin, a natural bioaromatic material, is always applied as a waste resource due to its low utilization efficiency. In this study, a ZnCl₂/CaCl₂/cellulose mixed system was used to prepare film materials via a regeneration method. The chemical structure and corresponding properties were characterized. The thermal decomposition process of film materials showed that with an increase of the heating rate, the maximum weight loss temperature gradually shifted to the higher-temperature region. Additionally, the combination of lignin with cellulose as composite films can effectively improve thermal stability. Furthermore, kinetics methods such as Kissing-Akahira-Sunose (KAS), Flynn-Wall-Ozawa (FWO), and Friedman were used to calculate the average activation energy (E). This study proposed a facile method for preparing biobased multifunctional composite films using two kinds of naturally renewable materials.