Screening of hydrogen bonds in modified cellulose acetates with alkyl chain substitutions

Acid insoluble lignin material production by chemical activation of olive endocarps for an efficient furfural adsorption-removal from aqueous solutions

The present work describes a protocol of chemical activation, with acid catalyst, of olive endocarps to obtain acid insoluble lignin-rich materials with high capacities for the adsorption of furfural present in aqueous media. During biomass activation, factors such as acid concentration, reaction time and temperature, solid/liquid ratio and the presence of water extractives strongly affected both the surface characteristics of the treated bioadsorbents and their capacities for furfural retention (percentage increase close to 600% with respect to the crude biomass). Once a treated solid with good adsorbent properties was obtained, the optimal conditions for adsorption were found: stirring speed 80 rpm, temperature 303 K and adsorbent load 7.5 g solid/50 cm3. Kinetic study indicated the pseudo-second order model provided the best fit of the experimental data. At 303 K, the equilibrium adsorption capacities values ranged from 2.27 mg g-1 to 29.29 mg g-1, for initial furfural concentrations between 0.49 g dm-3 and 12.88 g dm-3. Freundlich model presented the best isotherm (R2 = 0.996 and SE = 4.7%) providing KF and n values of 0.115 (mg g-1) (mg dm-3)-n and 0.610, respectively. Since physical interactions predominate in the adsorption of furfural on chemically activated olive endocarps, the furfural removal process could have occurred reversibly on the heterogeneous surface of the bioadsorbents.

Cellulose esters: Synthesis for further formation of films with magnetite nanoparticles incorporated

This study investigated the homogeneous synthesis of cellulose acetate (CA) and propionate (CP) with varying degrees of substitution (DS) from sisal cellulose in a N, N-dimethylacetamide/lithium chloride (DMAc/LiCl) solvent system. These esters were used to prepare neat (CADSF/CPDSF) and nanocomposite films (CADSFFe/CPDSFFe) from prior synthesized magnetite nanoparticles (NPs, Fe3O4, 5.1 ± 0.5 nm). Among the CA and CP series, the composite CA0.7FFe and the neat CP0.7F films exhibited the highest modulus of elasticity, 2105 MPa and 2768 MPa, respectively, probably a consequence of the continuous fibrous structures present on the surface of these films. Microsphere formation on the film's surface was observed in scanning electron microscopy micrographs. This points to applications in the controlled release of targeted substances. The VSM analysis showed that the cellulosic matrices preserved the superparamagnetic characteristics of the NPs. This study suggested a reduced coupling effect between nanoparticles inside polymeric films due to magnetic saturation at low fields. CA0.7FFe and CA1.3FFe composite films reached a saturation magnetization (MSAT) of 46 emu/g around 7 kOe field. Hosting magnetite nanoparticles in cellulose ester matrices may be an interesting way to develop new functional cellulose-based materials, which have the potential for diverse applications, including microelectromechanical systems and microsensors.

Fabrication of carvacrol loaded cellulose acetate phthalate/shellac composite film and its application to mackerel fillets preservation

In this research, the carvacrol (CAR) loaded cellulose acetate phthalate (CAP) /shellac (SH) films were prepared via electrostatic repulsion strategy and casting method. The CAP/SH-CAR films demonstrated excellent tensile strength, while also exhibiting good UV light barrier and thermal stability. The results showed that the addition of CAR significantly improved the barrier of the CAP film to water vapor and oxygen permeability. When the addition amount of CAR was 0.9 % (w/w) with respect to CAP content, the CAP/SH-CAR films exhibited good antibacterial activity and effectively reduced the growth of S. aureus and E. coli by approximately 47.9 % and 50.9 %, respectively. The presence of SH improved the retention rate of CAR in CAP/SH-CAR films, with the retention rate ranging from 45.2 to 56.8 %. Finally, the CAP/SH-CAR films were applied to preserve the mackerel fillets, indicating that the rate of freshness deterioration had been delayed and showing a good freshness preservation effect. Therefore, the CAP/SH-CAR films have the potential to be used as food packaging materials.

Upcycling of the Used Cigarette Butt Filters through Pyrolysis Process: Detailed Kinetic Mechanism with Bio-Char Characterization

Thermo-chemical conversion via the pyrolysis of cigarette butt (CB) filters was successfully valorized and upcycled in the pre-carbonization and carbonization stages. The pre-carbonization stage (devolatilization) of the precursor material (cellulose acetate filter, r-CAcF) was analyzed by micro-scale experiments under non-isothermal conditions using TG-DTG-DTA and DSC techniques. The results of a detailed kinetic study showed that the decomposition of r-CAcF takes place via complex mechanisms, including consecutive reaction steps and two single-step reactions. Consecutive stages include the α-transition referred to as a cellulose polymorphic transformation (cellulose I → II) through crystallization mechanism changes, where a more thermodynamically ordered system was obtained. It was found that the transformation rate of cellulose I → II ('cellulose regeneration') is strongly affected by the presence of alkali metals and the deacetylation process. Two single-step reactions showed significant overlapping behavior, which involves a nucleation-controlled scission mechanism (producing levoglucosan, gaseous products, and abundant radicals) and hydrolytic decomposition of cellulose by catalytic cleavage of glycosidic bonds with the presence of an acidic catalyst. A macro-scale experiment showed that the operating temperature and heating rate had the most notable effects on the total surface area of the manufactured carbon. A substantial degree of mesoporosity with a median pore radius of 3.1695 nm was identified. The presence of macroporosity on the carbon surface and acidic surface functional groups was observed.

Developing strong and tough cellulose acetate/ZIF67 intelligent active films for shrimp freshness monitoring

There is a growing demand for the development of intelligent active packaging films to maintain and monitor the freshness of meat food. Herein, nano Co-based MOF (ZIF67) with ammonia-sensitive and antimicrobial functions was successfully synthesized and then integrated into cellulose acetate (CA) matrix to prepare intelligent active films. The impacts of ZIF67 incorporation on the structure, physical and functional characteristics of CA film were fully investigated. The results demonstrated that the ZIF67 nanofillers were evenly dispersed in CA matrix, resulting in remarkable improvement on tensile strength, toughness, thermal stability, UV barrier, hydrophobicity and water vapor barrier ability of CA film. Furthermore, the prepared CA/ZIF67 films exhibited superb antimicrobial and ammonia-sensitive functions. The CA/ZIF67 intelligent films turned their color from blue at beginning to brown during progressive spoilage of shrimp. These results revealed that the CA/ZIF67 films with excellent antimicrobial and ammonia-sensitive functions could be applied in intelligent active food packaging.

Cellulose Acetate Film Containing Bonechar for Removal of Metribuzin from Contaminated Drinking Water

Bonechar presents high sorption capacity for mobile herbicides retained in soil and water. However, its use in a granulated and/or powder form makes it difficult to remove water. The objective of this study was to produce a cellulose acetate film with bonechar as a viable alternative to remove metribuzin from water. The treatments were composed of 2 and 3 g of bonechar fixed on a cellulose acetate film, pure bonechar, and a control (no bonechar). The sorption and desorption study was carried out in the equilibrium batch mode with five concentrations of metribuzin (0.25, 0.33, 0.5, 1, and 2 mg L−1). The water used in the experiment was potable water. Herbicide analysis was performed by High-Performance Liquid Chromatography (HPLC). The addition of 2 and 3 g of the bonechar fixed on the acetate film sorbed 40% and 60%, respectively, of the metribuzin at the lowest concentrations (0.25, 0.33, and 0.5 mg L−1). For both additions, desorption was low, being 7% and 2.5% at 24 and 120 h, respectively. There are still no reports of the production of cellulose acetate film with bonechar for herbicide removal in water, considered an alternative of easy handling and indicated for water treatment plants.