Colored titania nanocrystals and excellent photocatalysis for water cleaning

Green Synthesis of ZnO and Black TiO2 Materials and Their Application in Photodegradation of Organic Pollutants

ZnO and black TiO2 have been selected as the most efficient materials for organic pollution abatement due to their increased efficiency when compared to other materials. However, the concept of green chemistry makes it desirable to design green synthesis approaches for their production. In this study, black TiO2 was synthesized using an environmentally safe synthetic technique with glycerol as a reductant. ZnO was prepared by using ionic-liquid-based microwave-assisted extracts of Polygonum minus. To investigate the materials' potential to photodegrade organic pollutants, methylene blue (MB) and phenol were chosen as model organic pollutants. Both materials were found to exhibit spherical morphologies and a mesoporous structure and were efficient absorbers of visible light. ZnO exhibited electron-hole pair recombination lower than that of black TiO2. Black TiO2 was discovered to be an anatase phase, whereas ZnO was found to have a hexagonal wurtzite structure. In contrast to black TiO2, which had a surface area of 239.99 m2/g and a particle size of 28 nm, ZnO had a surface area of 353.11 m2/g and a particle size of 32 nm. With a degradation time of 60 min, ZnO was able to eliminate 97.50% of the 40 mg/L MB. Black TiO2, on the other hand, could reduce 90.0% of the same amount of MB in 60 min. When tested for phenol degradation, ZnO and black TiO2 activities were reduced by nearly 15 and 25%, respectively. A detailed examination of both ZnO and black TiO2 materials revealed that ZnO has more potential and versatility for the degradation of organic pollutants under visible light irradiation.

Electronic Structure, Optical and Magnetic Properties of Oxygen-Deficient Gray TiO2–δ(B)

The gray-colored oxygen-deficient TiO2–δ(B) nanobelts have been synthesized through a combination of the hydrothermal method followed by an ion exchange process and vacuum annealing. Electron paramagnetic resonance reveals an existence of F-centers in the form of electron-trapped oxygen vacancies within the anionic sublattice of the gray bronze TiO2 that induces its colouration. The diffuse reflectance spectroscopy showed that the formation of oxygen vacancies into TiO2(B) significantly increases its absorption intensity in both visible and near infrared ranges. The band gap of TiO2(B) with anionic defects is equal to 3.03 eV (against 3.24 eV for white TiO2(B) treated in air). Room temperature ferromagnetism associated with the defects was detected in gray TiO2–δ(B), thus indicating it belongs it to the class of dilute magnetic oxide semiconductors. It was found that in the low-temperature range (4 K), the magnetic properties of vacuum annealed TiO2(B) do not differ from those for TiO2(B) treated in air. We hope that the findings are defined here make a contribution to further progress in fabrication and manufacturing of defective TiO2-based nanomaterials for catalysis, magnetic applications, batteries, etc.

Preparation and modification methods of defective titanium dioxide-based nanoparticles for photocatalytic wastewater treatment-a comprehensive review

The rapid population growth and industrial expansion worldwide have created serious water contamination concerns. To curb the pollution issue, it has become imperative to use a versatile material for the treatment. Titanium dioxide (TiO₂) has been recognized as the most-studied nanoparticle in various fields of science and engineering due to its availability, low cost, efficiency, and other fascinating properties with a wide range of applications in modern technology. Recent studies revealed the photocatalytic activity of the material for the treatment of industrial effluents to promote environmental sustainability. With the wide band gap energy of 3.2 eV, TiO₂ can be activated under UV light; thus, many strategies have been proposed to extend its photoabsorption to the visible light region. In what follows, this has generated increasing attention to study its characteristics and structural modifications in different forms for photocatalytic applications. The present review provides an insight into the understanding of the synthesis methods of TiO₂, the current progress in the treatment techniques for the degradation of wide environmental pollutants employing modified TiO₂ nanoparticles, and the factors affecting its photocatalytic activities. Further, recent developments in using titania for practical applications, the approach for designing novel nanomaterials, and the prospects and opportunities in this exciting area have been discussed.

Synthesis and Characterization of Manganese-Modified Black TiO2 Nanoparticles and Their Performance Evaluation for the Photodegradation of Phenolic Compounds from Wastewater

The release of phenolic-contaminated treated palm oil mill effluent (TPOME) poses a severe threat to human and environmental health. In this work, manganese-modified black TiO₂ (Mn-B-TiO₂) was produced for the photodegradation of high concentrations of total phenolic compounds from TPOME. A modified glycerol-assisted technique was used to synthesize visible-light-sensitive black TiO₂ nanoparticles (NPs), which were then calcined at 300 °C for 60 min for conversion to anatase crystalline phase. The black TiO₂ was further modified with manganese by utilizing a wet impregnation technique. Visible light absorption, charge carrier separation, and electron–hole pair recombination suppression were all improved when the band structure of TiO₂ was tuned by producing Ti³⁺ defect states. As a result of the enhanced optical and electrical characteristics of black TiO₂ NPs, phenolic compounds were removed from TPOME at a rate of 48.17%, which is 2.6 times higher than P25 (18%). When Mn was added to black TiO₂ NPs, the Ti ion in the TiO₂ lattice was replaced by Mn, causing a large redshift of the optical absorption edges and enhanced photodegradation of phenolic compounds from TPOME. The photodegradation efficiency of phenolic compounds by Mn-B-TiO₂ improved to 60.12% from 48.17% at 0.3 wt% Mn doping concentration. The removal efficiency of phenolic compounds from TPOME diminished when Mn doping exceeded the optimum threshold (0.3 wt%). According to the findings, Mn-modified black TiO₂ NPs are the most effective, as they combine the advantages of both black TiO₂ and Mn doping.

Probing the formation and optical properties of Ti3+–TiO2 with (001) exposed crystal facet by ethanol-assisted fluorination

(001)-faceted TiO₂ with Ti³⁺ defects that are exclusively embedded in the bulk lattice near the surface was synthesized.

Glycerol-Mediated Facile Synthesis of Colored Titania Nanoparticles for Visible Light Photodegradation of Phenolic Compounds

In this study, we developed a glycerol-mediated safe and facile method to synthesize colored titania nanoparticles (NPs) via solution route. Our method is considerably effective and greener than other options currently available. Colored titania NPs were produced by hydrolyzing TiCl₄ precursor in aqueous solution containing different concentrations of glycerol (0.0, 1.163, 3.834, and 5.815 mol/L) and subsequent calcination at 300 °C for 1 h. Our results highlight firstly that glycerol-mediated synthesis is unlikely to affect the anatase crystalline structure of TiO₂, and secondly, that it would lead to coloration, band gap narrowing, and a remarkable bathochromic redshift of the optical response of titania. More importantly, the synthesized colored titania have Ti³⁺ ions, which, at least in terms of our samples, is the major factor responsible for its coloration. These Ti³⁺ species could induce mid gap states in the band gap, which significantly improve the visible light absorption capability and photocatalytic performance of the colored titania. The photocatalytic experiments showed that the colored TiO₂ NPs prepared in 1.163 mol/L aqueous glycerol solution displayed the best photocatalytic performance. Almost 48.17% of phenolic compounds and 62.18% of color were removed from treated palm oil mill effluent (POME) within 180 min of visible light irradiation.

Solar light induced transformation mechanism of allyl alcohol to monocarbonyl and dicarbonyl compounds on different TiO2: A combined experimental and theoretical investigation

Enols are an important group of photochemical precursors of atmospheric carbonyl compounds. However, the transformation mechanism is not fully understood. In this study, the photo-induced transformation of a typical enol, allyl alcohol, to carbonyl compounds on TiO₂ (P25) and aluminum reduced TiO₂ (P25, rutile and anatase TiO₂) were investigated. Intermediate results confirmed that a total of seven carbonyl compounds, including four monocarbonyl compounds (acetone, glycolaldehyde, 1,3-dihydroxyacetone and acrolein) and three dicarbonyl compounds (glyoxal, methylglyoxal and dimethylglyoxal), were formed on studied TiO₂. This is the first time to report the transformation of allyl alcohol to dicarbonyl compounds on TiO₂. The same byproducts formation indicated negligible effects of reduction treatment and crystal phase to the composition of carbonyl intermediates. However, the relative content ratio of dicarbonyl compounds to monocarbonyl ones on reduced P25 is ca. 4.1 times higher than that on P25, suggesting reduction treatment significantly accelerated the transformation of allyl alcohol or monocarbonyl compounds to dicarbonyl ones. Furthermore, both rutile and anatase crystal phases were found beneficial for the dicarbonyl compounds generation within enough reaction time, especially for anatase. The enhanced ^•OH was responsible for all accelerations. Furthermore, the intermediate results together with quantum chemical calculations confirmed that ^•OH addition and O₂ oxidation preferred converting allyl alcohol to dicarbonyl compounds rather than monocarbonyl ones. The present work could provide a deep insight into the transformation of allyl alcohol to carbonyl compounds, and efficiently replenish atmospheric transformation fate of enols.

Nanoarchitecture of TiO2 microspheres with expanded lattice interlayers and its heterojunction to the laser modified black TiO2 using pulsed laser ablation in liquid with improved photocatalytic performance under visible light irradiation

Different morphologies and crystal phases of black titanium dioxide (TiO₂) were synthesized using Pulsed Laser Ablation in Liquid (PLAL). The synthesized laser modified black TiO₂ (LMB-TiO₂) structures included hydrogenated anatase TiO₂ nanoparticles, as the core shell structures, and TiO₂ microspheres. TiO₂ core-shell nanoparticles, which had crystalline-disordered structures, demonstrated the laser ablation pulse duration-dependence growth of amorphous shells and hence formation of disordered TiO₂ nanoparticles with different thickness of hydrogen-doped amorphous shells were shown. TiO₂ microspheres with the yolk-shell like structures (YSHL-TiO₂ microspheres), on the other hand, showed the formation of rutile phases in the shell which encapsulate Lattice Expanded Planes (LEPs) in the core. The microspheres demonstrated phase transitions from anatase to rutile and size-dependent lattice interlayers expansion from 0.35 nm to 0.94 nm. The maximum particle size growth occurred when the samples were subjected to the laser ablation for 120 min. The crystal phase transition, consequently, led to the formation of heterostructured photocatalysts through construction of hydrogenated anatase TiO₂ nanoparticles junctions with rutile TiO₂ microspheres. The photocatalytic degradation of methylene blue (MB) using LMB-TiO₂ heterostructure was tested under visible light irradiation Results showed approximately 99% of MB was degraded after 60 min. Enhanced visible light absorption and increased charge carrier lifetime due to formation of different types of heterojunctions may explain the higher photocatalytic performance of LM-TiO₂ samples. Moreover, the Photoluminescence analysis indicated that hydroxyl radicals were the main active species involved in the photocatalytic degradation tests and therefore the photocatalysis mechanism was accordingly suggested.

Switchable Intrinsic Defect Chemistry of Titania for Catalytic Applications

The energy crisis is one of the most serious issue that we confront today. Among different strategies to gain access to reliable fuel, the production of hydrogen fuel through the water-splitting reaction has emerged as the most viable alternative. Specifically, the studies on defect-rich TiO2 materials have been proved that it can perform as an efficient catalyst for electrocatalytic and photocatalytic water-splitting reactions. In this invited review, we have included a general and critical discussion on the background of titanium sub-oxides structure, defect chemistries and the consequent disorder arising in defect-rich Titania and their applications towards water-splitting reactions. We have particularly emphasized the origin of the catalytic activity in Titania-based material and its effects on the structural, optical and electronic behavior. This review article also summarizes studies on challenging issues on defect-rich Titania and new possible directions for the development of an efficient catalyst with improved catalytic performance.

Synthesis and enhanced microwave absorption properties: a strongly hydrogenated TiO2 nanomaterial

Due to its improved physical and chemical performances, a strongly hydrogenated TiO₂ was designed and produced successfully by using a sealing-transfer reduction method at a relatively low temperature (425 °C). The microstructures, electromagnetic and microwave absorbing properties were investigated in detail. Experimental results revealed that: (1) the minimum reflection loss (RL) value of the hydrogenated TiO₂ up to -53.8 dB (99.999 99% of EM wave attenuation) was reached at 11.2 GHz, and the RL values below -20 dB (99%) were obtained in a frequency range of 7.3-16.8 GHz. (2) Compared to pristine TiO₂ and black TiO₂ in other reports, the present hydrogenated TiO₂ exhibited greatly improved microwave absorption performance. Moreover, the mechanism was also discussed. It was demonstrated that the excellent microwave absorption performance of the black TiO₂ arose from the strong dielectric loss, excellent impedance matching and attention loss due to associated relaxation and interfacial polarization. It is expected that the hydrogenated TiO₂ exhibits great potential applications in the area of high performance microwave absorbing materials. In addition, it is believed that the black TiO₂ @ magnetic metals composites will display an excellent microwave absorbing property.

Controllable reduced black titania with enhanced photoelectrochemical water splitting performance

Black titania prepared by metal-reduction methods is systematically studied and the controllable reduced black titania shows a five times higher H₂ production rate in photoelectrochemical water splitting.