Chemical reactivity of oxygen vacancies on the MgO surface: Reactions with CO2, NO2 and metals

CO adsorption on MgO thin-films: formation and interaction of surface charged defects

Two-dimensional (2D) materials formed by thin-films of metal oxides that grow on metal supports are commonly used in heterogeneous catalysis and multilayer electronic devices. Despite extensive research on these systems, the effects of charged defects at supported oxides on surface processes are still not clear. In this work, we perform spin-polarized density-functional theory (DFT) calculations to investigate formation and interaction of charged magnesium and oxygen vacancies, and Al dopants on MgO(001)/Ag(001) surface. The results show a sizable interface compressive effect that decreases the metal work function as electrons are added on the MgO surface with a magnesium vacancy. This surface displays a larger formation energy in a water environment (O-rich condition) even with additional Al-doping. Under these conditions, we found that a polar molecule such as CO is more strongly adsorbed on the low-coordination oxygen sites due to a larger contribution of the channeled electronic transport with the silver interface regardless of the surface charge. Therefore, these findings elucidate how surface intrinsic vacancies can influence or contribute to charge transfer, which allows one to explore more specific reactions at different surface topologies for more efficient catalysts for CO2 conversion.

Epitaxial growth of aligned MgO nanowire arrays on a single crystalline substrate

MgO nanostructures with different morphologies were fabricated by regulating the composition of raw materials, using the chemical vapor deposition method with gold as a catalyst. Polycrystalline MgO nanopillars were prepared using only Mg₃N₂ as the raw material. Single crystalline nanowire arrays can be obtained by adding carbon powder into the raw material. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for the detailed characterization of (100) nanowire arrays. Besides the vertical growth direction [100], the nanowires change into two kinds of orientations after growing to a certain length: 〈111〉 and 〈001〉. The epitaxial growth was attributed to the lattice match and regulation of the concentration of the Mg source. The variation of growth orientations was probably caused by the difference in surface energy and reaction temperature.

Electron beam analysis induces Cl vacancy defects in a NaCl thin film

This work reports on the electron-induced modification of NaCl thin film grown on Ag(110). We show using low energy electron diffraction that electron beam bombardment leads to desorption and formation of Cl vacancy defects on NaCl surface. The topographic structure of these defects is studied using scanning tunneling microscopy (STM) showing the Cl defects as depressions on the NaCl surface. Most of the observed defects are mono-atomic vacancies and are located on flat NaCl terraces. Auger electron spectroscopy confirms the effect of electron exposure on NaCl thin films showing Cl atoms desorption from the surface. Using density functional theory taken into account the van der Waals dispersion interactions, we confirm the observed experimental STM measurements with STM simulation. Furthermore, comparing the adsorption of defect free NaCl and defective NaCl monolayer on Ag(110) surfaces, we found an increase of the adhesion energy and the charge transfer between the NaCl film and the substrate due to the Cl vacancy. In details, the adhesion energy increases between the NaCl film and the metallic Ag substrate from 30.4 meV Å^-2for the NaCl film without Cl vacancy and from 39.5 meV Å^-2for NaCl film with a single Cl vacancy. The charge transfer from the NaCl film to the Ag substrate is enhanced when the vacancy is created, from 0.63e^-to 1.25e^-.

Invisible Surface Oxygen Vacancies in a Thin MgO Film: Impacts on the Chemical Activity and Secondary Electron Emission

Today, Fs defects in MgO as isolated surface neutral oxygen vacancies are in the focus of surface science, catalysis research, and emission coating of microchannel plates. With the 10^-4 atom % content at 750 K and under p_O2 = 10^-9 Torr, estimated by us from the known equilibrium T-x and p-T-x diagrams of MgO, Fs defects remain invisible or difficult-to-detect objects. The MgO(100) → MgO(100) + Fs + ¹/₂O₂ phase transition was studied in MgO films deposited by the metal-organic chemical vapor deposition (MOCVD) procedure from the mixed-ligand Mg precursor on Si substrates at 725 K in the O₂ flow where the nonstoichiometric phase (MgO/Fs) is formed in the gas medium containing simultaneous H₂, CO, H₂O, CO, and O₂ species in unbalanced concentrations. Realization of the above transition was proven theoretically and experimentally through kinetic-thermodynamic analysis of the nonequilibrium system with revealing thermodynamic motive forces, i.e., the positive enthalpy and entropy, as well as through a new combination of diagnostic methods including the original differential dissolution method, due to which separate determination of the point and morphological defects was achieved. It was found that Fs defects occur when oxygen in the immediate vicinity to the substrate surface is replaced practically completely by the oxidized products of the precursor and the resulting oxygen pressure becomes enough for this process. The 90 mass % of the as-deposited MgO-film-involved (MgO/Fs) phase; its chemical activity is demonstrated through dissolution in hot water, while the electron donor activity is through 9 at 750 eV secondary electron yield. A good understanding of gas-phase reactions between the precursors and oxygen provides the fundamental basis of the MOCVD process to deposit MgO films that are dense, free from carbon, and of homogeneous texture. This makes the MOCVD process suitable also for use as coatings of microchannel plates.

The catalytic destruction of antibiotic tetracycline by sulfur-doped manganese oxide (S-MgO) nanoparticles

The present study evaluates the efficacy of S-doped MgO (S-MgO) as compared with the plain MgO as a catalyst for destructive removal of tetracycline (TTC) in aqueous solutions. The S-MgO had around 6% S in its structure. Doping MgO with S caused increase in surface oxygen vacancy defects. Adding S-MgO (12 g/L) to a TTC aqueous solution (50 mg/L) caused removal of around 99% TTC at the neutral pH (ca. 5.1) and a short reaction time of 10 min. In comparison, plain MgO could remove only around 15% of TTC under similar experimental conditions. Diffusing O₂ into the TTC solution under the reaction with S-MgO resulted in a considerable improvement of TTC removal as compared to diffusing N₂. Complete removal of TTC and 86.4% removal of its TOC could be obtained using 2 g/L S-MgO nanoparticles. The removal of TTC increased with the increase in solution temperature. The presence of nitrate, sulfate and chloride did not considerably affect the removal of TTC using S-MgO while TTC removal significantly decreased at the presence of bicarbonate and phosphate. The S-MgO was a stable and reusable catalyst exhibiting much higher catalytic activity than plain MgO for the TTC destruction. Accordingly, S-MgO is an emerging and efficient catalyst for catalytic decomposition and mineralization of such pharmaceutical compounds as TTC under atmospheric temperature and pressure.

The effect of fluorine doping on the photocatalytic properties of hematite for water splitting

Fluorine-doped hematite samples with different concentrations were successfully synthesized through a hydrothermal method to improve the water splitting properties.

Facile synthesis of defect-induced highly-luminescent pristine MgO nanostructures for promising solid-state lighting applications

Successful demonstration of the facile synthesis of defect-induced highly-luminescent pristine MgO nanostructures for white-light generation and proposed WLED application.

Modelling the chemistry of Mn-doped MgO for bulk and (100) surfaces

We have investigated the energetic properties of Mn-doped MgO bulk and (100) surfaces using a QM/MM embedding computational method, calculating the formation energy for doped systems, as well as for surface defects, and the subsequent effect on chemical reactivity.