Electrochemical catalysis and stability of tetraamido macrocyclic ligands iron immobilized on modified pyrolytic graphite electrode

Enhanced Direct Electron Transfer Mediated Contaminant Degradation by Fe(IV) Using a Carbon Black-Supported Fe(III)-TAML Suspension Electrode System

Iron complexes of tetra-amido macrocyclic ligands (Fe-TAML) are recognized to be effective catalysts for the degradation of a wide range of organic contaminants in homogeneous conditions with the high valent Fe(IV) and Fe(V) species generated on activation of the Fe-TAML complex by hydrogen peroxide (H₂O₂) recognized to be powerful oxidants. Electrochemical activation of Fe-TAML would appear an attractive alternative to H₂O₂ activation, especially if the Fe-TAML complex could be attached to the anode, as this would enable formation of high valent iron species at the anode and, importantly, retention of the valuable Fe-TAML complex within the reaction system. In this work, we affix Fe-TAML to the surface of carbon black particles and apply this "suspension anode" process to oxidize selected target compounds via generation of high valent iron species. We show that the overpotential for Fe(IV) formation is 0.17 V lower than the potential required to generate Fe(IV) electrochemically in homogeneous solution and also show that the stability of the Fe(IV) species is enhanced considerably compared to the homogeneous Fe-TAML case. Application of the carbon black-supported Fe-TAML suspension anode reactor to degradation of oxalate and hydroquinone with an initial pH value of 3 resulted in oxidation rate constants that were up to three times higher than could be achieved by anodic oxidation in the absence of Fe-TAML and at energy consumptions per order of removal substantially lower than could be achieved by alternate technologies.

Redox- and EPR-Active Graphene Diiron Complex Nanocomposite

A mixed valence diiron(II/III) complex with the ligand 2,6-bis{bis[(2-pyridinylmethyl)amino]methyl}phenol (bppH) has been covalently anchored onto graphene using a mild in situ microwave-assisted diazonium coupling through an aryl amino precursor and isoamyl nitrite. A dinuclear iron complex is then formed by complexation of the grafted bppH-graphene material with iron(II) in the presence of dioxygen. X-ray photoelectron spectroscopy (XPS), atomic force microscopy, cyclic voltammetry, scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electron paramagnetic resonance (EPR) spectroscopy confirm the formation of the anchored ligand and derivative diiron complexes. Semiquantitative XPS analysis shows an average bppH ligand bulk loading of 0.33 mmol/g, corresponding to a significant 20.7 wt % of the functionalized material consisting of grafted moieties. EPR measurements reveal the existence of a strong isotropic S = 1/2 spin center associated with the graphene lattice, together with a much weaker S = 5/2 signal, associated with the iron(III) center of the grafted complex. The grafted complex is redox-active with surface-confined Fe^IIFe^II → Fe^IIFe^III (+0.56 V vs NHE), Fe^IIFe^III → Fe^IIIFe^III (+0.73 V), and Fe^IIIFe^III → Fe^IIIFe^IV (+0.95 V) redox processes accessible, with an estimated surface coverage of 58 pmol cm^-2 established from the electrochemical measurements.

Iron(III) diethylenetriaminepentaacetic acid complex on polyallylamine functionalized multiwalled carbon nanotubes: immobilization, direct electrochemistry and electrocatalysis

A nonenzymatic iron(III) diethylenetriaminepentaacetic acid (Fe(III)-DETPA) complex based amperometric sensor for the analytical determination of hydrogen peroxide was developed. By combining the electrostatic interaction between the Fe(III)-DETPA complex and polyallylamine (PAH) functionalized multiwalled carbon nanotubes (MWCNTs) as well as the ionotropic crosslinking interaction between PAH and ethylenediamine-tetramethylene phosphonic acid (EDTMP), the electroactive Fe(III)-DETPA complex was successfully incorporated within the MWCNT matrix, and firmly immobilized on the Au substrate electrode. The fabricated electrochemical sensor was characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical methods. The influences of solution pH and ionic strength on the electrochemical sensor were investigated. The prepared electrochemical sensor had a fast response to hydrogen peroxide (<3 s) and an excellent linear range of concentration from 1.25 × 10(-8) to 4.75 × 10(-3) M with a detection limit of 6.3 × 10(-9) M under the optimum conditions.