Methane dry reforming with CO2 on CeZr-oxide supported Ni, NiRh and NiCo catalysts prepared by sol–gel technique: Relationship between activity and coke formation

Catalytic Upgrading of Clean Biogas to Synthesis Gas

Clean biogas, produced by anaerobic digestion of biomasses or organic wastes, is one of the most promising substitutes for natural gas. After its purification, it can be valorized through different reforming processes that convert CH4 and CO2 into synthesis gas (a mixture of CO and H2). However, these processes have many issues related to the harsh conditions of reaction used, the high carbon formation rate and the remarkable endothermicity of the reforming reactions. In this context, the use of the appropriate catalyst is of paramount importance to avoid deactivation, to deal with heat issues and mild reaction conditions and to attain an exploitable syngas composition. The development of a catalyst with high activity and stability can be achieved using different active phases, catalytic supports, promoters, preparation methods and catalyst configurations. In this paper, a review of the recent findings in biogas reforming is presented. The different elements that compose the catalytic system are systematically reviewed with particular attention on the new findings that allow to obtain catalysts with high activity, stability, and resistance towards carbon formation.

Kinetic Regularities of Methane Dry Reforming Reaction on Nickel-Containing Modified Ceria–Zirconia

The Ni-containing catalysts based on ceria–zirconia doped with Ti and Ti+Nb were prepared by the solvothermal method in supercritical fluids. Ni deposition was carried out by incipient wetness impregnation and the one-pot technique. All materials were investigated by a complex of physicochemical methods (XRD, BET, TEM, H2-TPR). Samples catalytic properties were studied in methane dry reforming in the plug-flow reactor. Conversions of CH4 and CO2, H2/CO ratio, and CO and H2 yields were measured, and detailed kinetics analysis was carried out. The influence of Ni loading method and support modification on the catalytic behavior in the methane dry reforming process was studied. The preparation method of catalysts affects the textural characteristics. For one-pot samples, pore volume and surface area are lower than for impregnated samples. For catalysts on modified supports, strong metal–support interaction was shown to increase catalytic activity. A reduction pretreatment of samples was shown to have significant influence on their catalytic properties. The kinetic parameters such as reaction rate constant at 700 °C, effective activation energy, and TOF were estimated and analyzed.

Hydrogen Yield from CO2 Reforming of Methane: Impact of La2O3 Doping on Supported Ni Catalysts

Development of a transition metal based catalyst aiming at concomitant high activity and stability attributed to distinguished catalytic characteristics is considered as the bottleneck for dry reforming of methane (DRM). This work highlights the role of modifying zirconia (ZrO2) and alumina (Al2O3) supported nickel based catalysts using lanthanum oxide (La2O3) varying from 0 to 20 wt% during dry reforming of methane. The mesoporous catalysts with improved BET surface areas, improved dispersion, relatively lower reduction temperatures and enhanced surface basicity are identified after La2O3 doping. These factors have influenced the catalytic activity and higher hydrogen yields are found for La2O3 modified catalysts as compared to base catalysts (5 wt% Ni-ZrO2 and 5 wt% Ni-Al2O3). Post-reaction characterizations such as TGA have showed less coke formation over La2O3 modified samples. Raman spectra indicates decreased graphitization for La2O3 catalysts. The 5Ni-10La2O3-ZrO2 catalyst produced 80% hydrogen yields, 25% more than that of 5Ni-ZrO2. 5Ni-15La2O3-Al2O3 gave 84% hydrogen yields, 8% higher than that of 5Ni-Al2O3. Higher CO2 activity improved the surface carbon oxidation rate. From the study, the extent of La2O3 loading is dependent on the type of oxide support.

Smart Designs of Anti-Coking and Anti-Sintering Ni-Based Catalysts for Dry Reforming of Methane: A Recent Review

Dry reforming of methane (DRM) reaction has drawn much interest due to the reduction of greenhouse gases and production of syngas. Coking and sintering have hindered the large-scale operations of Ni-based catalysts in DRM reactions at high temperatures. Smart designs of Ni-based catalysts are comprehensively summarized in fourth aspects: surface regulation, oxygen defects, interfacial engineering, and structural optimization. In each part, details of the designs and anti-deactivation mechanisms are elucidated, followed by a summary of the main points and the recommended strategies to improve the catalytic performance, energy efficiency, and utilization rate.

Catalytic Performance of Lanthanum Promoted Ni/ZrO2 for Carbon Dioxide Reforming of Methane

Nickel catalysts supported on zirconium oxide and modified by various amounts of lanthanum with 10, 15, and 20 wt.% were synthesized for CO2 reforming of methane. The effect of La2O3 as a promoter on the stability of the catalyst, the amount of carbon formed, and the ratio of H2 to CO were investigated. In this study, we observed that promoting the catalyst with La2O3 enhanced catalyst activities. The conversions of the feed, i.e., methane and carbon dioxide, were in the order 10La2O3 > 15La2O3 > 20La2O3 > 0La2O3, with the highest conversions being about 60% and 70% for both CH4 and CO2 respectively. Brunauer–Emmett–Teller (BET) analysis showed that the surface area of the catalysts decreased slightly with increasing La2O3 doping. We observed that 10% La2O3 doping had the highest specific surface area (21.6 m2/g) and the least for the un-promoted sample. The higher surface areas of the promoted samples relative to the reference catalyst is an indication of the concentration of the metals at the mouths of the pores of the support. XRD analysis identified the different phases available, which ranged from NiO species to the monoclinic and tetragonal phases of ZrO2. Temperature programmed reduction (TPR) analysis showed that the addition of La2O3 lowered the activation temperature needed for the promoted catalysts. The structural changes in the morphology of the fresh catalyst were revealed by microscopic analysis. The elemental compositions of the catalyst, synthesized through energy dispersive X-ray analysis, were virtually the same as the calculated amount used for the synthesis. The thermogravimetric analysis (TGA) of spent catalysts showed that the La2O3 loading of 10 wt.% contributed to the gasification of carbon deposits and hence gave about 1% weight-loss after a reaction time of 7.5 h at 700 °C.

Well-Defined Materials for Heterogeneous Catalysis: From Nanoparticles to Isolated Single-Atom Sites

The use of well-defined materials in heterogeneous catalysis will open up numerous new opportunities for the development of advanced catalysts to address the global challenges in energy and the environment. This review surveys the roles of nanoparticles and isolated single atom sites in catalytic reactions. In the second section, the effects of size, shape, and metal-support interactions are discussed for nanostructured catalysts. Case studies are summarized to illustrate the dynamics of structure evolution of well-defined nanoparticles under certain reaction conditions. In the third section, we review the syntheses and catalytic applications of isolated single atomic sites anchored on different types of supports. In the final part, we conclude by highlighting the challenges and opportunities of well-defined materials for catalyst development and gaining a fundamental understanding of their active sites.

Methane dry reforming over Ni catalysts supported on Ce–Zr oxides prepared by a route involving supercritical fluids

Ce0.5Zr0.5O2mixed oxides were prepared in a flow reactor in supercritical isopropanol with acetylacetone as a complexing agent. Variation of the nature of the Zr salt and the temperature of synthesis affected the phase composition, morphology and specific surface area of oxides. X-ray diffraction and Raman spectroscopy studies revealed formation of metastable t” and t’ phases. Oxides are comprised of agglomerates with sizes depending on the synthesis parameters. Loading NiO decreases the specific surface area without affecting X-ray particle sizes of supports. Such sintering was the most pronounced for a support with the highest specific surface area, which resulted in the lowest surface content of Ni as estimated by X-ray photoelectron spectroscopy and in the formation of flattened NiO particles partially embedded into the support. The catalytic activity and stability of these samples in the dry reforming of methane were determined by the surface concentration of Ni and the morphology of its particle controlled by the metal-support interaction, which also depends on the type of catalyst pretreatment. Samples based on ceria-zirconia oxides prepared under these conditions provide a higher specific catalytic activity as compared with the traditional Pechini route, which makes them promising for the practical application.

A Review on Bimetallic Nickel-Based Catalysts for CO2 Reforming of Methane

In recent years, CO₂ reforming of methane (dry reforming of methane, DRM) has become an attractive research area because it converts two major greenhouse gasses into syngas (CO and H₂ ), which can be directly used as fuel or feedstock for the chemical industry. Ni-based catalysts have been extensively used for DRM because of its low cost and good activity. A major concern with Ni-based catalysts in DRM is severe carbon deposition leading to catalyst deactivation, and a lot of effort has been put into the design and synthesis of stable Ni catalysts with high carbon resistance. One effective and practical strategy is to introduce a second metal to obtain bimetallic Ni-based catalysts. The synergistic effect between Ni and the second metal has been shown to increase the carbon resistance of the catalyst significantly. In this review, a detailed discussion on the development of bimetallic Ni-based catalysts for DRM including nickel alloyed with noble metals (Pt, Ru, Ir etc.) and transition metals (Co, Fe, Cu) is presented. Special emphasis has been provided on the underlying principles that lead to synergistic effects and enhance catalyst performance. Finally, an outlook is presented for the future development of Ni-based bimetallic catalysts.

Cooperativity and Dynamics Increase the Performance of NiFe Dry Reforming Catalysts

The dry reforming of methane (DRM), i.e., the reaction of methane and CO₂ to form a synthesis gas, converts two major greenhouse gases into a useful chemical feedstock. In this work, we probe the effect and role of Fe in bimetallic NiFe dry reforming catalysts. To this end, monometallic Ni, Fe, and bimetallic Ni-Fe catalysts supported on a Mg_xAl_yO_z matrix derived via a hydrotalcite-like precursor were synthesized. Importantly, the textural features of the catalysts, i.e., the specific surface area (172-178 m²/g_cat), pore volume (0.51-0.66 cm³/g_cat), and particle size (5.4-5.8 nm) were kept constant. Bimetallic, Ni₄Fe₁ with Ni/(Ni + Fe) = 0.8, showed the highest activity and stability, whereas rapid deactivation and a low catalytic activity were observed for monometallic Ni and Fe catalysts, respectively. XRD, Raman, TPO, and TEM analysis confirmed that the deactivation of monometallic Ni catalysts was in large due to the formation of graphitic carbon. The promoting effect of Fe in bimetallic Ni-Fe was elucidated by combining operando XRD and XAS analyses and energy-dispersive X-ray spectroscopy complemented with density functional theory calculations. Under dry reforming conditions, Fe is oxidized partially to FeO leading to a partial dealloying and formation of a Ni-richer NiFe alloy. Fe migrates leading to the formation of FeO preferentially at the surface. Experiments in an inert helium atmosphere confirm that FeO reacts via a redox mechanism with carbon deposits forming CO, whereby the reduced Fe restores the original Ni-Fe alloy. Owing to the high activity of the material and the absence of any XRD signature of FeO, it is very likely that FeO is formed as small domains of a few atom layer thickness covering a fraction of the surface of the Ni-rich particles, ensuring a close proximity of the carbon removal (FeO) and methane activation (Ni) sites.

Na-promoted Ni/ZrO2 dry reforming catalyst with high efficiency: details of Na2O–ZrO2–Ni interaction controlling activity and coke formation

Balanced, strong interaction of Ni–Na₂O–ZrO₂ catalyst components under CO₂ reforming of methane is a criterion of good catalytic activity and stability.

Surface Spectroscopy on UHV-Grown and Technological Ni-ZrO2 Reforming Catalysts: From UHV to Operando Conditions

Ni nanoparticles supported on ZrO₂ are a prototypical system for reforming catalysis converting methane to synthesis gas. Herein, we examine this catalyst on a fundamental level using a 2-fold approach employing industrial-grade catalysts as well as surface science based model catalysts. In both cases we examine the atomic (HRTEM/XRD/LEED) and electronic (XPS) structure, as well as the adsorption properties (FTIR/PM-IRAS), with emphasis on in situ/operando studies under atmospheric pressure conditions. For technological Ni–ZrO₂ the rather large Ni nanoparticles (about 20 nm diameter) were evenly distributed over the monoclinic zirconia support. In situ FTIR spectroscopy and ex situ XRD revealed that even upon H₂ exposure at 673 K no full reduction of the nickel surface was achieved. CO adsorbed reversibly on metallic and oxidic Ni sites but no CO dissociation was observed at room temperature, most likely because the Ni particle edges/steps comprised Ni oxide. CO desorption temperatures were in line with single crystal data, due to the large size of the nanoparticles. During methane dry reforming at 873 K carbon species were deposited on the Ni surface within the first 3 h but the CH₄ and CO₂ conversion hardly changed even during 24 h. Post reaction TEM and TPO suggest the formation of graphitic and whisker-type carbon that do not significantly block the Ni surface but rather physically block the tube reactor. Reverse water gas shift decreased the H₂/CO ratio. Operando studies of methane steam reforming, simultaneously recording FTIR and MS data, detected activated CH₄ (CH₃ and CH₂), activated water (OH), as well as different bidentate (bi)carbonate species, with the latter being involved in the water gas shift side reaction. Surface science Ni–ZrO₂ model catalysts were prepared by first growing an ultrathin “trilayer” (O–Zr–O) ZrO₂ support on an Pd₃Zr alloy substrate, and subsequently depositing Ni, with the process being monitored by XPS and LEED. Apart from the trilayer oxide, there is a small fraction of ZrO₂ clusters with more bulk-like properties. When CO was adsorbed on the (fully metallic) Ni particles at pressures up to 100 mbar, both PM-IRAS and XPS indicated CO dissociation around room temperature and blocking of the Ni surface by carbon (note that on the partially oxidized technological Ni particles, CO dissociation was absent). The Ni nanoparticles were stable up to 550 K but annealing to higher temperatures induced Ni migration through the ultrathin ZrO₂ support into the Pd₃Zr alloy. Both approaches have their benefits and limitations but enable us to address specific questions on a molecular level.

An investigation on the influence of catalyst composition, calcination and reduction temperatures on Ni/MgO catalyst for dry reforming of methane

Catalytic activity of Ni/MgO catalyst investigated at different Ni content (20, 40 and 80 wt%), calcination (450, 600 and 800 °C) and reduction temperatures (550 and 800 °C) for dry reforming reaction at very high space velocity.

Progress in Synthesis of Highly Active and Stable Nickel-Based Catalysts for Carbon Dioxide Reforming of Methane

In recent decades, rising anthropogenic greenhouse gas emissions (mainly CO2 and CH4 ) have increased alarm due to escalating effects of global warming. The dry carbon dioxide reforming of methane (DRM) reaction is a sustainable way to utilize these notorious greenhouse gases. This paper presents a review of recent progress in the development of nickel-based catalysts for the DRM reaction. The enviable low cost and wide availability of nickel compared with noble metals is the main reason for persistent research efforts in optimizing the synthesis of nickel-based catalysts. Important catalyst features for the rational design of a coke-resistant nickel-based nanocatalyst for the DRM reaction are also discussed. In addition, several innovative developments based on salient features for the stabilization of nickel nanocatalysts through various means (which include functionalization with precursors, synthesis by plasma treatment, stabilization/confinement on mesoporous/microporous/carbon supports, and the formation of metal oxides) are highlighted. The final part of this review covers major issues and proposed improvement strategies pertaining to the rational design of nickel-based catalysts with high activity and stability for the DRM reaction.

A review of dry (CO2) reforming of methane over noble metal catalysts

Dry (CO2) reforming of methane (DRM) is a well-studied reaction that is of both scientific and industrial importance. This reaction produces syngas that can be used to produce a wide range of products, such as higher alkanes and oxygenates by means of Fischer-Tropsch synthesis. DRM is inevitably accompanied by deactivation due to carbon deposition. DRM is also a highly endothermic reaction and requires operating temperatures of 800-1000 °C to attain high equilibrium conversion of CH4 and CO2 to H2 and CO and to minimize the thermodynamic driving force for carbon deposition. The most widely used catalysts for DRM are based on Ni. However, many of these catalysts undergo severe deactivation due to carbon deposition. Noble metals have also been studied and are typically found to be much more resistant to carbon deposition than Ni catalysts, but are generally uneconomical. Noble metals can also be used to promote the Ni catalysts in order to increase their resistance to deactivation. In order to design catalysts that minimize deactivation, it is necessary to understand the elementary steps involved in the activation and conversion of CH4 and CO2. This review will cover DRM literature for catalysts based on Rh, Ru, Pt, and Pd metals. This includes the effect of these noble metals on the kinetics, mechanism and deactivation of these catalysts.

Highly coke-resistant ni nanoparticle catalysts with minimal sintering in dry reforming of methane

Nickel catalysts are typically used for hydrogen production by reforming reactions. Reforming methane with carbon dioxide, called dry reforming of methane (DRM), is a good way to produce hydrogen or syngas (a mixture of hydrogen and carbon monoxide) from two notable greenhouse gases. However, Ni catalysts used for DRM suffer from severe coke deposition. It has been known that small Ni nanoparticles are advantageous to reduce coke formation, but the high reaction temperature of DRM (800 °C) inevitably induces aggregation of the nanoparticles, leading to severe coke formation and degraded activity. Here, we develop highly coke-resistant Ni catalysts by immobilizing premade Ni nanoparticles of 5.2 nm in size onto functionalized silica supports, and then coating the Ni/SiO2 catalyst with silica overlayers. The silica overlayers enable the transfer of reactants and products while preventing aggregation of the Ni nanoparticles. The silica-coated Ni catalysts operate stably for 170 h without any degradation in activity. No carbon deposition was observed by temperature programmed oxidation (TPO), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Raman spectroscopy. The Ni catalysts without silica coating show severe sintering after DRM reaction, and the formation of filamentous carbon was observed. The coke-resistant Ni catalyst is potentially useful in various hydrocarbon transformations.

The role of carbonaceous deposits in the activity and stability of Ni-based catalysts applied in the dry reforming of methane

Highly stable Ni catalysts with varying Ni contents up to 50 mol% originating from hydrotalcite-like precursors were applied in the dry reforming of methane at 800 and 900 °C.