Characterisation of high surface area nanocomposites for glycerol transformation: Effect of the presence of silica on the structure and catalytic activity

Laser-power dependence effects on the structural stability of nanocomposite catalysts studied by Raman spectroscopy: On the structure-activity correlations in glycerol acetylation

Structural properties of binary CeAl, CeMn, NiAl, CeZr, SnTi and ZrMn nanocomposite oxide catalysts were monitored towards the Laser Raman spectroscopy investigations providing new insights to control catalytic applications upon temperature ranges at which the laser power was varied. The lattice vibrational properties were investigated by varying the incident laser power during Raman measurements from 0.017 mW to 4.0 mW. Structural changes in nanocomposites were achieved upon increasing laser power, which induced local heating disorder causing the sintering of CeMn, SnTi, and ZrMn nanocomposites. The laser-power dependence effects on the structural stability of CeAl, NiAl, and CeZr were observed with high amounts of oxygen vacancy defects over CeAl upon laser power heating. Both CeMn and ZrMn exhibited phase transitions from MnO₂ to α-Mn₂O₃ being the use of the latter nanocomposites limited to work at 1.1 mW. The structure-activity correlations for the nanocomposite oxide catalysts were evaluated through the acetylation of glycerol with acetic acid reaction to produce valuable acetins. Remarkable shifts in the Raman bands wavenumbers and other spectral changes in the lattice mode were caused by laser-induced phenomena accounting for the undesired phase formation and particle growths, as well. This resulted in a low catalytic performance of the NiAl, SnTi, CeMn and ZrMn owing to the thermal effects. Contrary, CeAl and CeZr were more active for acetins products avoiding the phase transformations due to their structural stability at high temperatures, which in turn avoided leaching of the active Ce sites during the reaction.

Continuous Flow Upgrading of Selected C2-C6 Platform Chemicals Derived from Biomass

The ever increasing industrial production of commodity and specialty chemicals inexorably depletes the finite primary fossil resources available on Earth. The forecast of population growth over the next 3 decades is a very strong incentive for the identification of alternative primary resources other than petro-based ones. In contrast with fossil resources, renewable biomass is a virtually inexhaustible reservoir of chemical building blocks. Shifting the current industrial paradigm from almost exclusively petro-based resources to alternative bio-based raw materials requires more than vibrant political messages; it requires a profound revision of the concepts and technologies on which industrial chemical processes rely. Only a small fraction of molecules extracted from biomass bears significant chemical and commercial potentials to be considered as ubiquitous chemical platforms upon which a new, bio-based industry can thrive. Owing to its inherent assets in terms of unique process experience, scalability, and reduced environmental footprint, flow chemistry arguably has a major role to play in this context. This review covers a selection of C₂ to C₆ bio-based chemical platforms with existing commercial markets including polyols (ethylene glycol, 1,2-propanediol, 1,3-propanediol, glycerol, 1,4-butanediol, xylitol, and sorbitol), furanoids (furfural and 5-hydroxymethylfurfural) and carboxylic acids (lactic acid, succinic acid, fumaric acid, malic acid, itaconic acid, and levulinic acid). The aim of this review is to illustrate the various aspects of upgrading bio-based platform molecules toward commodity or specialty chemicals using new process concepts that fall under the umbrella of continuous flow technology and that could change the future perspectives of biorefineries.

Temperature and high pressure effects on the structural features of catalytic nanocomposites oxides by Raman spectroscopy

Structural characterizations of nanostructured oxides were studied by X-ray diffraction (XRD), Raman and infrared spectroscopy. The oxides catalysts namely, SnO2, ZrO2, CeO2, MnOx, Al2O3 and TiO2 were prepared by a nanocasting route and the effect of the temperature and pressure on the stability of the solids was evaluated. Raman spectra showed that ZrO2 and TiO2 exhibited phase transitions at moderate temperatures whereas CeO2, SnO2 and MnOx had an effective creation of defects in their structures upon annealing at elevated temperatures. The results suggested also that the effect of the temperature on the particles growth is related to the type of oxide. In this regard, phase transition by up to 600°C accelerated the sintering of ZrO2 and CeO2 grains compared to TiO2, SnO2 and MnOx counterparts. Under hydrostatic pressures lower than 10GPa, rutile TiO2 and tetragonal ZrO2 exhibited pressure induced phase transition whereas CeO2 and SnO2 were stable at pressures close to 15GPa. The experiments revealed that the nanostructured SnO2 oxide exhibited stable performance at relatively high temperatures without phase transition or sintering, being suitable to be used as catalysts in the range of temperature and pressure studied.

Catalytic oxidation and adsorption of elemental mercury over nanostructured CeO2–MnOx catalyst

The presence of oxygen vacancies and synergetic interaction between Ce and Mn were responsible for superior Hg⁰ oxidation performance of CeO₂–MnO_x compared to pure CeO₂ and MnO_x.

MnO2/CeO2 for catalytic ultrasonic degradation of methyl orange

Catalytic ultrasonic degradation of aqueous methyl orange was studied in this paper. Heterogeneous catalyst MnO2/CeO2 was prepared by impregnation of manganese oxide on cerium oxide. Morphology and specific surface area of MnO2/CeO2 catalyst were characterized and its composition was determined. Results showed big differences between fresh and used catalyst. The removal efficiency of methyl orange by MnO2/CeO2 catalytic ultrasonic process was investigated. Results showed that ultrasonic process could remove 3.5% of methyl orange while catalytic ultrasonic process could remove 85% of methyl orange in 10 min. The effects of free radical scavengers were studied to determine the role of hydroxyl free radical in catalytic ultrasonic process. Results showed that methyl orange degradation efficiency declined after adding free radical scavengers, illustrating that hydroxyl free radical played an important role in degrading methyl orange. Theoretic analysis showed that the resonance size of cavitation bubbles was comparable with the size of catalyst particles. Thus, catalyst particles might act as cavitation nucleus and enhance ultrasonic cavitation effects. Measurement of H2O2 concentration in catalytic ultrasonic process confirmed this hypothesis. Effects of pre-adsorption on catalytic ultrasonic process were examined. Pre-adsorption significantly improved methyl orange removal. The potential explanation was that methyl orange molecules adsorbed on catalysts could enter cavitation bubbles and undergo stronger cavitation.