Fischer–Tropsch synthesis on the Al2O3-modified ordered mesoporous Co3O4 with an enhanced catalytic activity and stability

Reducibility of Al3+-Modified Co3O4: Influence of Aluminum Distribution

The reduction of Co-based oxides doped with Al3+ ions has been studied using in situ XRD and TPR techniques. Al3+-modified Co3O4 oxides with the Al mole fraction Al/(Co + Al) = 1/6; 1/7.5 were prepared via coprecipitation, with further calcination at 500 and 850 °C. Using XRD and HAADF-STEM combined with EDS element mapping, the Al3+ cations were dissolved in the Co3O4 lattice; however, the cation distribution differed and depended on the calcination temperature. Heating at 500 °C led to the formation of an inhomogeneous (Co,Al)3O4 solid solution; further treatment at 850 °C provoked the partial decomposition of mixed Co-Al oxides and the formation of particles with an Al-depleted interior and Al-enriched surface. It has been shown that the reduction of cobalt oxide by hydrogen occurs via the following transformations: (Co,Al)3O4 → (Co,Al)O → Co. Depending on the Al distribution, the course of reduction changes. In the case of the inhomogeneous (Co,Al)3O4 solid solution, Al stabilizes intermediate Co(II)-Al(III) oxides during reduction. When Al3+ ions are predominantly on the surface of the Co3O4 particles, the intermediate compound consists of Al-depleted and Al-enriched Co(II)-Al(III) oxides, which are reduced independently. Different distributions of elemental Co and Al in mixed oxides simulate different types of the interaction phase in Co3O4/γ-Al2O3-supported catalysts. These changes in the reduction properties can significantly affect the state of an active component of the Co-based catalysts.

Efficient and recyclable Ni-Ce-Mn-N modified ordered mesoporous carbon electrode during electrocatalytic ozonation process for the degradation of simulated high-salt phenol wastewater

In this study, an efficient and stable NiO/CeO₂/MnO₂-modified nitrogen-doped ordered mesoporous carbon (NOMC) particle electrode was developed, in which the metal oxides were mosaicked within the pore channels by one-pot skeleton hybridization, and the comodification of NiO/CeO₂/MnO₂/N was found to improve the electrocatalytic activity and stability of the particle electrode. The improved stability of the ordered mesoporous carbon towards pore collapse was applied to the degradation of simulated high-salt phenol wastewater by an electrocatalytic ozonation process using simple binder pelletization. The modified ordered mesoporous carbon shows a specific surface area of 269.7 m² g^-1 and a pore size of 3.17 nm, and SEM and TEM were used to show that the mesoporous structure is well maintained and the metal nanoparticles are well dispersed. The electrochemically active area of the Ni_2%/Ce_0.5%/Mn_2.5%-NOMC particle electrode reaches 224.65 mF cm^-2, which indicates that NiO improves the capacitance of the ordered mesoporous carbon and accelerates the electron transfer efficiency. Encouragingly, the phenol removal efficiency is found to reach up to 93.0% for 60 min over a wide range of pH values, with an initial phenol concentration of 150 mg L^-1, low current (0.03 A) and fast reaction rate (0.0895 min^-1), and the presence of CeO₂ ameliorates the low activity of the particle electrode under acidic conditions. These results indicate that the presence of pyridine-N and β-MnO₂ effectively mitigates carbon corrosion and improves electrode stability, as the accumulation of large amounts of ·OH at 20 min and the maintenance of a degradation efficiency of more than 90% after eight cycles provides a viable solution for the widespread practical application of ordered mesoporous carbon particle electrodes.

Effects of Sm on Fe-Mn catalysts for Fischer-Tropsch synthesis

Sm-promoted FeMn catalysts were prepared by the co-precipitation method and characterized by N₂ adsorption, XRD, CO-TPD, H₂-TPD, CO₂-TPD, H₂-TPR, XPS and MES. It was found that compared with the un-promoted catalyst, when Sm was added at a proper content, the catalyst showed a larger BET surface area and promoted the formation of iron particles with a smaller size. The presence of Sm could increase the surface charge density of iron, which enhanced the Fe–C bond and promoted the stability and amount of CO dissociated adsorption, as confirmed by XPS and CO-TPD. Furthermore, according to MES, Sm could promote the formation of Fe₅C₂, which was the active phase of FTS. In addition, Sm could also enhance the basicity of the catalysts and suppress the H₂ adsorption capacity, which inhibited the hydrogenation reaction and the conversion of olefins to paraffins, as verified by the results of CO₂-TPD and H₂-TPD. According to the FTS performance results, compared with the observations for the un-promoted catalysts, when the molar ratio of Sm to Fe was 1%, the CO conversion increased from 63.4% to 70.4%, the sum of light olefins in the product distribution increased from 26.6% to 32.6, and the ratio of olefins to paraffins increased to 4.18 from 4.09.

The effect of samarium on iron-based catalysts for Fischer–Tropsch synthesis was investigated.

Ordered mesoporous CoMOx (M = Al or Zr) mixed oxides for Fischer–Tropsch synthesis

A superior structural stability of the ordered mesoporous CoMO_x catalysts synthesized using the KIT-6 hard template was observed under the reductive Fischer–Tropsch reaction conditions due to the formation of strongly interacting stable Co₃O₄–ZrO₂ mixed oxides.