Polymeric catalytic membrane for ozone treatment of DEET in water

Continuous operation of nano-catalytic ozonation using membrane separation coupling system: Influence factors and mechanism

The application of nano-catalysts in improving the ozonation removal efficiency for refractory organic compounds has been extensively investigated. However, cost-effective nano-catalysts separation remains a challenge. In this study, membrane separation processes were employed to separate nano-MgO catalysts from an ozonation system. A continuous nano-catalytic ozonation membrane separation (nCOMS) coupling system was successfully constructed for treating quinoline. The results showed that long hydraulic retention time (HRT) and high nano-MgO dosage could improve the quinolone removal efficiency but shorten operation cycles. At the optimal operation conditions of HRT = 4 h and nano-MgO dosage = 0.2 g/L, the nCOMS system achieved a stable quinoline removal efficiency of 85.2% for 240 min running with a transmembrane pressure lower than 10 kPa. The quinoline removal efficiency contribution for ozonation, catalysis and membrane separation was 57.1%, 24.9% and 18.0%, respectively. Compared to ozonation membrane separation system, the fouling rate index of the nCOMS system increased by 60% under optimal conditions, but the irreversible fouling was reduced to 28%. In addition, the nCOMS system exhibited reduced adverse effects of coexisting natural organic matter (NOM) on quinoline removal and membrane fouling. In conclusion, the nCOMS system demonstrated higher quinoline removal efficiency, lower irreversible fouling, and reduced adverse effect of coexisting NOM, thereby signifying its potential for practical applications in advanced treatment of industrial wastewater.

Construction of WO3 nanocubes@Loess for rapid photocatalytic degradation of organics in wastewater under sunlight

In nowadays, environmental pollution has been greatly improved, but the development of low-cost and environmentally friendly materials are still challenge in the field of water treatment. Herein, a cheap and eco-friendly natural loess particle (LoP) was used for in situ growth of tungsten trioxide nanocubes (WO3NCs) on its surface via a simple one-pot hydrothermal method, which afforded a stable loess-based photocatalyst (WO3NCs@LoP). It was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) analysis, UV-Vis diffuse reflectance spectra (UV-Vis DRS), and X-ray photoelectron spectroscopy (XPS). The photocatalytic performances of WO3NCs@LoP were applied to photodegradation of organics under visible-light illumination. It was found that the removal rate of methylene blue (MB) got to 99% within 20 min, which was higher than that of materials, such as pure LoP and WO3NCs. Moreover, the photocatalytic activity of WO3NCs@LoP remained 85% after 9 cycling times, indicating its high stability and reusability. It was suggested that the synergy of the well narrowed band gap and effectual control of e--h+ recombination in WO3NCs@LoP improve its photodegradation efficiency. In summary, using natural minerals (LoP) as carrier, a novel eco-friendly photocatalyst could be explored for photodegradation of organic pollutions in wastewater treatment.

Fabrication of nitrogen-doped graphene nanosheets anchored with carbon nanotubes for the degradation of tetracycline in saline water

The treatment of wastewater with high salinity is still a challenge because of the quenching effect of various anions on radical processes. The nonradical process may be a more promising pathway. Herein, a 3D structured nitrogen-doped graphene nanosheet anchored with carbon nanotubes (N-GS-CNTs) was prepared by direct pyrolysis of K₃Fe(CN)₆. The as-prepared catalyst can effectively activate peroxymonosulfate (PMS) for mineralization of tetracycline (TC) over a wide pH range (from 3 to 11) and even in high saline water (500 mM Cl^-, HCO₃^-, etc.). The degradation mechanism was elucidated by both experimental characterizations and DFT calculations. The high catalytic efficiency was attributed to accelerated electron transfer from donor (TC) to acceptor (PMS) in the presence of the catalyst, which acts as electron shuttle mediators to promote a nonradical process. At the same time, the catalyst also enhances the production of singlet oxygen (¹O₂), hence further increasing the degradation rate. This study not only provides a simple method for synthesizing N-GS-CNT catalysts but also provides new insights into the electron transfer pathway for the removal of organic pollutants under high salinity conditions.

Catalytic membrane-based oxidation-filtration systems for organic wastewater purification: A review

Catalytic membranes can simultaneously realize physical separation and chemical oxidation in one integrated system, which is the frontier technology for effective removal of organic containments in wastewater treatment. The catalytic membrane coupled with advanced oxidation processes (AOPs) not only significantly enhances the pollutant removal efficiency but also inhibits the fouling of the membrane via self-cleaning. In this review, the preparation approaches of catalytic membranes including blending, surface coating, and bottom-up synthesis are comprehensively summarized. The different integrated catalytic membrane systems coupled with photocatalysis, Fenton oxidation, persulfate activations, ozonation and electrocatalytic oxidation are discussed in terms of mechanisms and performance. Besides, the principles, influencing factors, advantages and issues of the different catalytic membrane/oxidation systems are outlined comparatively. Finally, the future challenges, and research directions are suggested, which is conducive to the design and development of catalytic membrane-oxidation systems for practical remediation of organic containing wastewater.

Photocatalysis for Organic Wastewater Treatment: From the Basis to Current Challenges for Society

Organic pollutants such as dyes, antibiotics, analgesics, herbicides, pesticides, and stimulants become major sources of water pollution. Several treatments such as absorptions, coagulation, filtration, and oxidations were introduced and experimentally carried out to overcome these problems. Nowadays, an advanced technique by photocatalytic degradation attracts the attention of most researchers due to its interesting and promising mechanism that allows spontaneous and non-spontaneous reactions as they utilized light energy to initiate the reaction. However, only a few numbers of photocatalysts reported were able to completely degrade organic pollutants. In the past decade, the number of preparation techniques of photocatalyst such as doping, morphology manipulation, metal loading, and coupling heterojunction were studied and tested. Thus, in this paper, we reviewed details on the fundamentals, common photocatalyst preparation for coupling heterojunction, morphological effect, and photocatalyst’s characterization techniques. The important variables such as catalyst dosage, pH, and initial concentration of sample pollution, irradiation time by light, temperature system, durability, and stability of the catalyst that potentially affect the efficiency of the process were also discussed. Overall, this paper offers an in-depth perspective of photocatalytic degradation of sample pollutions and its future direction.

Catalytic Ozonation and Membrane Contactors—A Review Concerning Fouling Occurrence and Pollutant Removal

Membrane filtration has been widely used in water and wastewater treatment. However, this process is not very effective for the removal of refractory organic compounds (e.g., of pharmaceutical origin). Coupling membrane filtration with ozonation (or other Advanced Oxidation Methods) can enhance the degradation of these compounds and, subsequently, the incidence of membrane fouling (i.e., the major problem of membrane uses) would be also limited. Ozonation is an efficient oxidative process, although ozone is considered to be a rather selective oxidant agent and sometimes it presents quite low mineralization rates. An improvement of this advanced oxidation process is catalytic ozonation, which can decrease the by-product formation via the acceleration of hydroxyl radicals production. The hydroxyl radicals are unselective oxidative species, presenting high reaction constants with organic compounds. An efficient way to couple membrane filtration with catalytic ozonation is the deposition of an appropriate solid catalyst onto the membrane surface. However, it must be noted that only metal oxides have been used as catalysts in this process, while the membrane material can be of either polymeric or ceramic origin. The relevant studies regarding the application of polymeric membranes are rather scarce, because only a few polymeric materials can be ozone-resistant and the deposition of metal oxides on their surface presents several difficulties (e.g., affinity etc.). The respective literature about catalytic membrane ozonation is quite limited; however, some studies have been performed concerning membrane fouling and the degradation of micropollutants, which will be presented in this review. From the relevant results it seems that this hybrid process can be an efficient technology both for the reduction of fouling occurrence as well as of enhancement of micropollutant removal, when compared to the application of single filtration or ozonation.

Flow-Through Catalytic Reactors Based on Metal Nanoparticles Immobilized within Porous Polymeric Gels and Surfaces/Hollows of Polymeric Membranes

State-of-the-art of flow-through catalytic reactors based on metal nanoparticles immobilized within the pores of nano-, micro- and macrosized polymeric gels and in the surface or hollow of polymeric membranes is discussed in this mini-review. The unique advantages of continuous flow-through nanocatalysis over the traditional batch-type analog are high activity, selectivity, productivity, recyclability, continuous operation, and purity of reaction products etc. The methods of fabrication of polymeric carriers and immobilization technique for metal nanoparticles on the surface of porous or hollow structures are considered. Several catalytic model reactions comprising of hydrolysis, decomposition, hydrogenation, oxidation, Suzuki coupling and enzymatic reactions in the flow system are exemplified. Realization of “on-off” switching mechanism for regulation of the rate of catalytic process through controlling the mass transfers of reactants in liquid media with the help of stimuli-responsive polymers is demonstrated. Comparative analysis of the efficiency of different flow-through catalytic reactors for various reactions is also surveyed.