Synthesis of magnetic-photo-Fenton catalyst for degradation of emerging pollutant

Magnetic TiO2/Fe3O4-Chitosan Beads: A Highly Efficient and Reusable Catalyst for Photo-Electro-Fenton Process

Heterogeneous photo-electro-Fenton process is an attractive technology for the removal of recalcitrant pollutants. To better exploit the presence of an irradiation source, a bifunctional catalyst with TiO2 nanoparticles embedded into an iron–chitosan matrix was developed. The catalytic activity of the catalyst was improved by the optimization of the loaded TiO2content. The prepared composite catalysts based on TiO2, Fe3O4 and chitosan were called TiO2/Fe3O4-CS beads. The best catalyst with an optimal ratio TiO2/Fe = 2 exhibited a high efficiency inthe degradation and mineralization of chlordimeform (CDM) insecticide. Under the optimum conditions (concentration of catalyst equal to 1 g L−1 and applied current intensity equal to 70 mA), a real effluent doped with 30 mg L−1 of CDM was efficiently treated, leading to 80.8 ± 1.9% TOC reduction after 6 h of treatment, with total removal of CDM after only 1 h.The generated carboxylic acids and minerals wereidentified and quantified. Furthermore, the stability and reusability of the developed catalyst was examined, and an insignificant reduction in catalytic activity was noticed forfour consecutive cycles of the photo-electro-Fenton process. Analyses using SEM, XRD and VSM showed a good stability of the physicochemical properties of the catalyst after use.

Photocatalytic-Fenton Process under Simulated Solar Radiation Promoted by a Suitable Catalyst Selection

Considering water scarcity, photo-based processes have been presented as a depollution technique, which should be optimized in order to be applied in the future. For that, the addition of an active photocatalyst and the usage of solar radiation are mandatory steps. Thus, Fe3O4–SiO2–TiO2 was synthesized, and its performance was evaluated using simulated solar radiation and methylene blue as a model pollutant. Under optimal conditions, 86% degradation was attained in 1 h. These results were compared to recent published data, and the better performance can be attributed to both the operational conditions selection and the higher photocatalyst activity. Indeed, Fe3O4–SiO2–TiO2 was physico-chemically characterized with techniques such as XRD, N2 isotherms, spectrophotometry, FTIR, electrochemical assays and TEM.

Low cost effective heterogeneous photo-Fenton catalyst from drinking water treatment residuals for reactive blue 19 degradation: Preparation and characterization

Four different catalysts from drinking water treatment residuals (DWTR) were prepared via impregnation in the iron nitrate, calcined at different temperatures ranged from 200°C to 500°C, and tested for the reactive blue 19 oxidation using the heterogeneous photo-Fenton, under UVA light source. XRD and XPS results revealed that iron nature was found under a ferric oxide form (Fe³⁺ ) similar to the magnetite. Calcination temperature results showed a significant effect on the activity of the catalysts. RB19 and TOC removals were 99% and 79%, respectively, with the best catalyst that calcined at 500°C in optimal conditions as follows: initial pH solution = 3, 10 mM of H₂ O₂ dosage, 0.5 g/L of catalyst loading, reaction temperature 35°C, and I_UVA  = 3.55 MW/cm² for 50 mg/L of RB19. The reusability of the catalyst after three cycles showed complete removal of RB19 and 65% TOC removal. PRACTITIONER POINTS: Synthetized heterogeneous photo-Fenton catalyst from drinking water treatment residuals for the photo Fenton oxidation. The calcination temperatures plays a crucial role in catalyst photocatalytic activity. Degradation of reactive blue 19 with Fe/DWTR-500 in presence of H₂ O₂ . The Fe/DWTR-500 catalyst exhibited the best photocatalytic activity. Reusability studies of Fe/DWTR-500 and the kinetics of reactive blue 19 degradation were investigated.

Catalytic activity comparison of natural ferrous minerals in photo-Fenton oxidation for tertiary treatment of dyeing wastewater

Natural ferrous minerals are readily available and recyclable catalysts in photo-Fenton-like oxidation for wastewater treatment. In this work, typical ferrous oxide and sulfide minerals including magnetite, chalcopyrite, and pyrrhotite were exploited as catalysts in heterogeneous photo-Fenton oxidation for purification of biological effluent of dyeing wastewater. In a wide initial pH range (3.0~7.5), ferrous mineral-based heterogeneous photo-Fenton-like reactions were proven to be effective on the oxidation of recalcitrant pollutants. COD removals achieved 60.57%, 58.83%, and 57.41% using pyrrhotite, chalcopyrite, and magnetite, respectively, as catalyst under ultraviolet irradiation of 220~275 nm at H₂O₂ concentration of 9.8 mM. The corresponding COD removals were 51.75% and 34.09% with or without ferrous sulfate additions in UV/H₂O₂ systems. Minerals exhibited excellent stability and reusability with photo-catalytic activity reduction of less than 10% in the reuse of 5 cycles. Dissolved iron concentrations were determined to be 1.86 mg L^-1, 4.62 mg L^-1, and 7.53 mg L^-1 for magnetite, chalcopyrite, and pyrrhotite, respectively, at pH 3 and decreased to zero in neutral pH environment, which were much lower than those required for homogenous Fenton reaction. It was deduced that oxidation of recalcitrant pollutants was mainly catalyzed by Fe(II) on the mineral surface. The more reactive oxygen species such as hydroxyl radicals were resulted from the reaction of surface Fe (II) with H₂O₂, H₂O₂ photolysis, and charge separation of minerals under UV irradiation.

Magnetic field assisted preparation of PES-Ni@MWCNTs membrane with enhanced permeability and antifouling performance

Multiple wall carbon nanotubes (MWCNTs), as an excellent material, have been used in various applications including preparation of polymer-MWCNTs composite membranes. However, few reports have combined the magnetic Ni@MWCNTs with polyether sulfone (PES) membrane to improve its antifouling performance to humic acid (HA), sodium alginate (SA), bovine serum albumin (BSA) and yeast (YE) solutions. In this study, the Ni@MWCNTs was generated by immersing MWCNTs into Ni²⁺ solution where in-situ reduction reaction was launched by the adsorbed Ag⁺ on MWCNTs. Since the loaded Ni endowed magnetism to MWCNTs, the Ni@MWCNTs can be easily attracted onto the membrane surface by an external magnetic field during the phase inversion process. The morphology measurements confirmed that the Ni@MWCNTs headed out of the PES-Ni@MWCNTs membrane surface. Because the MWCNTs played a role of free channels for water molecules, the composite membrane water flux reached to threefold flux of the pristine membrane. Moreover, the PES-Ni@MWCNTs membranes displayed the obviously enhanced antifouling ability during all the three alternative filtration cycles of water and BSA, SA, YE and HA solutions. In addition, the optimal PES-Ni@MWCNTs membrane demonstrated a flux recovery rate (FRR) of 67.89%, 85.53%, 60.28 and 90.12% for BSA, SA, YE and HA, respectively, which were not only much higher than that of the pristine membrane, but also exhibited significant improvements comparing with the previous studies. Further results of extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory indicated that the modified membrane possessed advantageous interaction energies with contaminant molecules over the pristine membrane.