Comprehensive understanding of SiO2-promoted Fe Fischer-Tropsch synthesis catalysts: Fe-SiO2 interaction and beyond

Sustainable Removal of BTEX Gas Using Regenerated Metal Containing SiO2

In the last decades, the removal of benzene, toluene, ethylbenzene, and xylene (BTEX) has been considered a major environmental crisis. In this study, two novel nanocomposite materials (Fe2O3/SiO2 and Fe2O3-Mn2O3/SiO2) that have regeneration ability by UV irradiation have been fabricated to remove BTEX at ambient temperature. This research revealed that both nanocomposites could remove more than 85% of the BTEX in the first cycle. The adsorption capacities followed the order of ethylbenzene > m-xylene > toluene > benzene as in the molecular weight order. The reusability test using UV irradiation showed that the performance of Fe2O3/SiO2 decreased drastically after the fifth cycle for benzene. On the other hand, when Mn is located in the nanocomposite structure, Fe2O3-Mn2O3/SiO2 could maintain its adsorption performance with more than 80% removal efficiency for all the BTEX for ten consecutive cycles. The difference in the reusability of the two nanocomposites is that the electron energy (from the valence band to the conduction band) for BTEX decomposition is changed due to the presence of manganese. This study provides a promising approach for designing an economical reusable nanomaterial, which can be used for VOC-contaminated indoor air.

Effects of Potassium Loading over Iron–Silica Interaction, Phase Evolution and Catalytic Behavior of Precipitated Iron-Based Catalysts for Fischer-Tropsch Synthesis

Potassium (K) promoter and its loading contents were shown to have remarkable effects on the Fe–O–Si interaction of precipitated Fe/Cu/K/SiO2 catalysts for low-temperature Fischer-Tropsch synthesis (FTS). With the increase in K content from 2.3% (100 g Fe based) up to 7% in the calcined precursors, Fe–O–Si interaction was weakened, as reflected by ATR/FTIR, H2-TPR and XPS investigations. XRD results confirmed that the diffraction peak intensity from (510) facet of χ-Fe5C2 phase strengthened with increasing K loading, which indicates the crystallite size of χ-Fe5C2 increased with the increase in K contents either during the syngas reduction/carburization procedure or after FTS reaction. H2-TPH results indicated that more reactive surface carbon (alpha-carbon) was obtained over the higher K samples pre-carburized by syngas. Raman spectra illustrated that a greater proportion of graphitic carbon was accumulated over the surface of spent samples with higher K loading. At the same time, ATR-FTIR, XRD and Mössbauer spectra (MES) characterization results showed that a relatively higher level of bulk phase Fayalite (Fe2SiO4) species was observed discernibly in the lowest K loading sample (2.3 K%) in this work. The catalytic evaluation results showed that the CO conversion, CO2 selectivity and O/P (C2–C4) ratio increased progressively with the increasing K loading, whereas a monotonic decline in both CO conversion and O/P (C2–C4) ratio was observed on the highest K loading sample during c.a. 280 h of TOS.

Production of Light Olefins via Fischer-Tropsch Process Using Iron-Based Catalysts: A Review

The production of light olefins, as the critical components in chemical industries, is possible via different technologies. The Fischer–Tropsch to olefin (FTO) process aims to convert syngas to light olefins with high selectivity over a proper catalyst, reduce methane formation, and avoid the production of excess CO2. This review describes the production of light olefins through the FTO process using both unsupported and supported iron-based catalysts. The catalytic properties and performances of both the promoted and bimetallic unsupported catalysts are reviewed. The effect of support and its physico-chemical properties on the catalyst activity are also described. The proper catalyst should have high stability to provide long-term performance without reducing the activity and selectivity towards the desired product. The good dispersion of active metals on the surface, proper porosity, optimized metal-support interaction, a high degree of reducibility, and providing a sufficient active phase for the reaction are important parameters affecting the reaction. The selection of the suitable catalyst with enhanced activity and the optimum process conditions can increase the possibility of the FTO reaction for light-olefins production. The production of light olefins via the FTO process over iron-based catalysts is a promising method, as iron is cheap, shows higher resistance to sulfur, and has a higher WGS activity which can be helpful for the feed gas with a low H2/CO ratio, and also has higher selectivity towards light olefins.

Development of an Iron-Based Fischer—Tropsch Catalyst with High Attrition Resistance and Stability for Industrial Application

In order to develop an iron-based catalyst with high attrition resistance and stability for Fischer–Tropsch synthesis (FTS), a series of experiments were carried out to investigate the effects of SiO2 and its hydroxyl content and a boron promoter on the attrition resistance and catalytic behavior of spray-dried precipitated Fe/Cu/K/SiO2 catalysts. The catalysts were characterized by means of N2 physisorption, nuclear magnetic resonance (NMR), X-ray diffraction (XRD), Raman spectrum, X-ray photoelectron spectroscopy (XPS), H2-thermogravimetric analysis (H2-TGA), temperature-programmed reduction and hydrogenation (TPR and TPH), and scanning and transmission electron microscopy (SEM and TEM). The FTS performance of the catalysts was tested in a slurry-phase continuously stirred tank reactor (CSTR), while the attrition resistance study included a physical test with the standard method and a chemical attrition test under simulated reaction conditions. The results indicated that the increase in SiO2 content enhances catalysts’ attrition resistance and FTS stability, but decreases activity due to the suppression of further reduction of the catalysts. Moreover, the attrition resistance of the catalysts with the same silica content was greatly improved with an increase in hydroxyl number within silica sources, as well as the FTS activity and stability to some degree. Furthermore, the boron element was found to show remarkable promotion of FTS stability, and the promotion mechanism was discussed with regard to probable interactions between Fe and B, K and B, and SiO2 and B, etc. An optimized catalyst based on the results of this study was finalized, scaled up, and successfully applied in a megaton industrial slurry bubble FTS unit, exhibiting excellent FTS performance.