Recent advances in energy chemistry of precious-metal-free catalysts for oxygen electrocatalysis

ZIF-Co3O4@ZIF-Derived Urchin-Like Hierarchically Porous Carbon as Efficient Bifunctional Oxygen Electrocatalysts

Co3O4 nanoparticles were sandwiched into interlayers between ZIF-8 and ZIF-67 to form ZIF-Co3O4@ZIF precursors. Pyrolysis of ZIF-Co3O4@ZIF yielded an urchin-like hierarchically porous carbon (Co@CNT/NC), the thorns of which were carbon nanotubes embedded Co nanoparticles. With large specific surface area and hierarchically porous structure, as-prepared Co@CNT/NC exhibited excellent bifunctional oxygen electrocatalytic performances. It has good ORR performance with E1/2 of 0.85 V, which exceeds the Pt/C half-wave potential (E1/2=0.83 V). In addition, Co@CNT/NC has an OER performance close to that of RuO2. To further demonstrate the effect of Co modifying on the properties, the samples were subjected to acid washing treatment. Co-based nanoparticles were proved to After acid washing, there was obvious loss of Co particles in Co@CNT/NC, resulting in poor oxygen electrocatalysis. So, the pyrolysis products of ZIF-8-Co3O4@ZIF-67 retained large specific surface area and porous structure can be retained, and on the other hand, the carbon tube structure and original polyhedron framework. Besides, existence of Co nanoparticle@carbon nanotube provided more active sites and improved the ORR and OER performances.

Recent Advances of Electrocatalyst and Cell Design for Hydrogen Peroxide Production

Electrochemical synthesis of H2O2 via a selective two-electron oxygen reduction reaction has emerged as an attractive alternative to the current energy-consuming anthraquinone process. Herein, the progress on electrocatalysts for H2O2 generation, including noble metal, transition metal-based, and carbon-based materials, is summarized. At first, the design strategies employed to obtain electrocatalysts with high electroactivity and high selectivity are highlighted. Then, the critical roles of the geometry of the electrodes and the type of reactor in striking a balance to boost the H2O2 selectivity and reaction rate are systematically discussed. After that, a potential strategy to combine the complementary properties of the catalysts and the reactor for optimal selectivity and overall yield is illustrated. Finally, the remaining challenges and promising opportunities for high-efficient H2O2 electrochemical production are highlighted for future studies.

Tunable dual cationic redox couples boost bifunctional oxygen electrocatalysis for long-term rechargeable Zn-air batteries

Efficient nonprecious bifunctional electrocatalysts toward oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are essential for improving the electrochemical performance of Zinc-air (Zn-air) batteries. Herein, we report a cobalt-doped Mn₂(OH)₃VO₃ catalyst prepared by facile hydrothermal method, and the ratios of cationic redox couples of catalysts were tuned with different Co doping amounts. The as-prepared Mn_1.8Co_0.2(OH)₃VO₃ (MnCoVO-1) catalyst achieves the highest ratio of (Mn³⁺Mn⁴⁺)/Mn²⁺ and Co³⁺/Co²⁺ redox couples which serve as ORR and OER active sites respectively, and exhibits the enhanced electrocatalytic performance. Furthermore, when employed as air-cathode catalyst for rechargeable Zn-air batteries, the MnCoVO-1 catalyst reveals a high power density (278 mW cm^-2), enhanced rate performance and outstanding long-term stability of over 270 h. This work demonstrates the Co-doped Mn₂(OH)₃VO₃ with optimized electronic structure by rational doping engineering can serve as a promising bifunctional catalyst for oxygen electrocatalysis and rechargeable Zn-air batteries.

Highly Selective Electrocatalytic Oxidation of Amines to Nitriles Assisted by Water Oxidation on Metal-Doped α-Ni(OH)2

Selective oxidation to synthesize nitriles is critical for feedstock manufacturing in the chemical industry. Current strategies typically involve substitutions of alkyl halides with toxic cyanides or the use of strong oxidation reagents (oxygen or peroxide) under ammoxidation/oxidation conditions, setting considerable challenges in energy efficiency, sustainability, and production safety. Herein, we demonstrate a facile, green, and safe electrocatalytic route for selective oxidation of amines to nitriles under ambient conditions, assisted by the anodic water oxidation on metal-doped α-Ni(OH)₂ (a typical oxygen evolution reaction catalyst). By controlling the balance between co-adsorption of the amine molecule and hydroxyls on the catalyst surface, we demonstrate that Mn doping significantly promotes the subsequent chemical oxidation of amines, resulting in Faradaic efficiencies of 96% for nitriles under ≥99% conversion. This anodic oxidation is further coupled with cathodic hydrogen evolution for overall atomic economy and additional green energy production.

FeNi LDH/V2CTx/NF as Self-Supported Bifunctional Electrocatalyst for Highly Effective Overall Water Splitting

The development of bifunctional electrocatalysts with efficient oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is still a key challenge at the current stage. Herein, FeNi LDH/V2CTx/nickel foam (NF) self-supported bifunctional electrode was prepared via deposition of FeNi LDH on V2CTx/NF substrate by hydrothermal method. Strong interfacial interaction between V2CTx/NF and FeNi LDH effectively prevented the aggregation of FeNi LDH, thus exposing more catalytic active sites, which improved electrical conductivity of the nanohybrids and structural stability. The results indicated that the prepared FeNi LDH/V2CTx/NF required 222 mV and 151 mV overpotential for OER and HER in 1 M KOH to provide 10 mA cm-2, respectively. Besides, the FeNi LDH/V2CTx/NF electrocatalysts were applied to overall water splitting, which achieved a current density of 10 mA cm-2 at 1.74 V. This work provides ideas for improving the electrocatalytic performance of electrocatalysts through simple synthesis strategies, structural adjustment, use of conductive substrates and formation of hierarchical structures.

Coupling Co-N-C with MXenes Yields Highly Efficient Catalysts for H2O2 Production in Acidic Media

The electrochemical oxygen reduction reaction (ORR) offers a promising method to replace the anthraquinone process for hydrogen peroxide (H₂O₂) production. However, the efficiency of this process suffers from sluggish kinetics, particularly in an acidic environment. Therefore, employing catalysts with high electroactivity is highly desirable for H₂O₂ synthesis. Here, an effective strategy for preparing Co-N-C/Ti₃C₂T_x with high H₂O₂ selectivity and ORR reactivity is proposed. The acquired Co-N-C/Ti₃C₂T_x shows excellent H₂O₂ electrosynthesis performance in acidic media with H₂O₂ productivity of up to 3200 ppm h^-1, superior to state-of-the-art catalysts. Interestingly, a H₂O₂ concentration of 6.0 wt % was obtained after the stability test, and the Co-N-C/Ti₃C₂T_x catalyst was found to effectively catalyze organic dye degradation. Further analysis reveals that the enhanced H₂O₂ electrosynthesis performance originates from the layered structure and the oxygen functional groups of Ti₃C₂T_x. The layered structure can effectively promote increased exposure of active sites, while the oxygen functional groups will fine-tune the electronic structure of Co atoms, allowing a selective ORR pathway to produce H₂O₂. This work provides a strategy to design and fabricate highly efficient catalysts for H₂O₂ production and degradation of organic pollutants.

Highly Active and Stable Fe/Co/N Co-doped Carbon-Anchored Pd Nanoparticles for Oxygen Reduction Reaction

A highly active and stable electrocatalyst based on Pd nanoparticles anchored on zeolitic imidazolate framework-derived Fe/Co/N co-doped carbon (Pd/FeCoNC) is prepared. FeCo alloy nanoparticles are uniformly dispersed and wrapped by graphene layers in Fe/Co/N co-doped carbon (FeCoNC). The influences of carbonization temperature on the structure and catalytic activity of FeCoNC toward oxygen reduction reaction (ORR) are investigated. The FeCoNC prepared at 800 °C (FeCoNC-800) has a favorable ORR catalytic activity as a consequence of the synergistic effect of Fe/Co/N co-doping and hierarchical pore structures of coexisting micropores and mesopores. Pyridinic N in FeCoNC is a preferential adsorption site for anchoring Pd nanoparticles. Pd/FeCoNC exhibits both superior activity and durability to 40 wt % Pt/C at the same level of metallic mass loading, which shows a 44 mV higher half-wave potential (0.88 V) than Pt/C and a 91% remaining current of the initial after 10,000 s. The Fe/Co/N co-doping and hierarchical pores of FeCoNC contribute a large diffusion current, and the introduction of Pd realizes more positive onset and half-wave potentials. This work provides an easy way for preparing low-cost and high-efficiency catalysts for ORR.

Defect and Doping Co-Engineered Non-Metal Nanocarbon ORR Electrocatalyst

Exploring low-cost and earth-abundant oxygen reduction reaction (ORR) electrocatalyst is essential for fuel cells and metal-air batteries. Among them, non-metal nanocarbon with multiple advantages of low cost, abundance, high conductivity, good durability, and competitive activity has attracted intense interest in recent years. The enhanced ORR activities of the nanocarbons are normally thought to originate from heteroatom (e.g., N, B, P, or S) doping or various induced defects. However, in practice, carbon-based materials usually contain both dopants and defects. In this regard, in terms of the co-engineering of heteroatom doping and defect inducing, we present an overview of recent advances in developing non-metal carbon-based electrocatalysts for the ORR. The characteristics, ORR performance, and the related mechanism of these functionalized nanocarbons by heteroatom doping, defect inducing, and in particular their synergistic promotion effect are emphatically analyzed and discussed. Finally, the current issues and perspectives in developing carbon-based electrocatalysts from both of heteroatom doping and defect engineering are proposed. This review will be beneficial for the rational design and manufacturing of highly efficient carbon-based materials for electrocatalysis.

In situ grown CoS on nickel foam pre-deposited with sulphur as an efficient OER electrocatalyst

The NiCo-150 composite electrode on the NF was prepared via a simple two-step electrodeposition method with outstanding OER performance with an overpotential of 145 mV at 10 mA cm⁻² and 337 mV at 50 mA cm⁻².