In-situ polymerized cross-linked binder for cathode in lithium-sulfur batteries

Ultrathin carbon film as ultrafast rechargeable cathode for hybrid sodium dual-ion capacitor

The development of electrochemical energy storage devices has a decisive impact on clean renewable energy. Herein, novel ultrafast rechargeable hybrid sodium dual-ion capacitors (HSDICs) were designed by using ultrathin carbon film (UCF) as the cathode material. The UCF is synthesized by a simple low temperature catalytic route followed by an acid leaching process. UCF owns a large adsorption interface and number of additional active sites, which is due to the nitrogen doping. In addition, there exists several short-range order carbons on the surface of UCF, which are beneficial for anionic storage. An ultrafast rechargeable remarkable performance, remarkable anion hybrid storage capability and outstanding structure stability is fully tapped employing UCF as cathode for HSDICs. The electrochemical performance of UCF in a half-cell system at the operating voltage between 1.0 and 4.8 V, achieving an admirable specific discharge capacity of 358.52 mAh·g-1at 500 mA·g-1, and a high capacity retention ratio of 98.42% after cycling 2500 times at 1000 mA·g-1, respectively. Besides, with the support ofex-situTEM and EDS mapping, the structural stability principle and anionic hybrid storage mechanism of UCF electrode are investigated in depth. In the full-cell system, HSDICs with the UCF as cathode and hard carbon as anode also presents a super-long cycle stability (80.62% capacity retention ratio after cycling 1300 times at 1000 mA·g-1).

Confinement of Zinc Salt in Ultrathin Heterogeneous Film to Stabilize Zinc Metal Anode

Aqueous zinc metal batteries (AZMBs) have drawn great attention due to the high theoretical capacity, low redox potential, and abundance reserves. However, the practical application of rechargeable AZMBs are hindered by the poor reversibility of Zn metal anode, owing to easy dendrite growth and serious side reactions. Herein, the preparation of heterogeneous interfacial film with highly dispersed and confined zinc salt in a 2D channel by coassembling polyamide 6, zinc trifluoromethanesulfonate, and layered double hydroxides, which significantly suppresses the dendrite formation, H₂ evolution reaction as well as O₂ corrosion is reported. The as-developed Zn anodes exhibit a long cycling life up to 1450 h with low reversible deposition potential. Moreover, the assembled Zn||Mn battery delivers a high initial capacity of 321 mAh g^-1 and a low capacity decay of ≈0.05% per cycle after 590 cycles, which is promising for high-performance AZMBs. A fluorescent film to realize the in situ observation of the Zn anode during cycling, which provides a new chance for visual observation of the working state of the Zn interface, is also assembled.

An interlayer composed of a porous carbon sheet embedded with TiO2 nanoparticles for stable and high rate lithium-sulfur batteries

The shuttling of lithium polysulfides (LiPSs) in lithium-sulfur (Li-S) batteries results in low sulfur utilization and fast capacity decay, hindering their practical applications. Constructing an interlayer is an efficient way to block the LiPS shuttling, but maintaining a low Li ion diffusion resistance with such an interlayer is hard to achieve. Herein, a thin porous carbon nanosheet embedded with TiO2 nanoparticles (denoted PCNS-TiO2) was used to fabricate an interlayer on the separator, which effectively solves the above problem. The PCNS-TiO2 was prepared by using the Ti3C2Tx MXene as the two-dimensional (2D) template directing the porous carbon sheet formation, and the Ti3C2Tx transformed into TiO2 nanoparticles embedded in the PCNS. The decomposition of the MXene eliminates the ion blocking effect by the 2D nanosheet structure. The thin and hierarchical porous structure allows fast Li ion diffusion across the interlayer, and at the same time, the porous structure and the strong adsorption ability of TiO2 effectively block the polysulfide diffusion. Thus, the Li-S battery with this interlayer shows good rate performance with a high capacity of 627 mA h g-1 at 2 C. Meanwhile, stable cycling performance is also achieved, showing a low capacity decay of 0.063% per cycle after 300 cycles at 0.5 C.