Super-assembled highly compressible and flexible cellulose aerogels for methylene blue removal from water

Iron‑calcium dual crosslinked graphene oxide/alginate aerogel microspheres for extraordinary elimination of tetracycline in complex wastewater: Performance, mechanism, and applications

Antibiotics have been considered as a group of emerging contaminants for their stable chemical structure, significant pseudo-persistence, and biological toxicity. Tetracycline (TC), as one of the typical antibiotics frequently detected in environmental media, can cause the dissemination and accumulation of antibiotic resistance gene (ARG), ultimately threatening human health and environmental safety. Herein, a novel iron‑calcium di-crosslinked graphene oxide/alginate (GO/SA-Fe3+-Ca2+) aerogel was facilely synthesized for TC uptake. It was found that the introduction of GO nanosheets and Fe3+ sites into composite enormously enhanced TC removal. Specifically, TC can be stably and efficiently eliminated over the wide pH range of 5-8. The fitted maximum qe with Liu isotherm model at 308 K reached 1664.05 mg/g, surpassing almost all reported sorbents. The pseudo-second-order kinetic model with chemical sorption characteristics better fitted TC adsorption process, which was endothermic and spontaneous in nature. Multifarious adsorptive sites of GO/SA-Fe3+-Ca2+ synergically participated in TC uptake through multi-mechanisms (e.g., π-π EDA, cation-π bonding, H-bonding, Fe3+-coordination, and electrostatic attraction, etc.). The as-prepared composite showed satisfactory TC removal in several runs of adsorption-desorption operations, high salinity, and model aquaculture wastewater. Moreover, the packed-column could continuously run for >200 h until adsorption saturation was achieved with a dynamic adsorption capacity of 216.69 mg/g, manifesting its scale-up engineering applications. All above merits make as-constructed composite an alternative sorbent for eliminating TC from complex wastewater.

Eco-friendly regeneration of lignin with acidic deep eutectic solvent for adsorption of pollutant dyes for water cleanup

In this study, a simple and eco-friendly method was used to treat alkaline lignin with an acidic deep eutectic solvent (DES) to obtain regenerated lignin for the efficient adsorption of pollutant dyes from aqueous environment. Based on the yield and adsorption capacity of the sorbent for these dyes, conditions such as the type and concentration of DES component, solid-to-liquid ratio, reaction time, and temperature were optimized. By characterizing and comparing alkali lignin with regenerated lignin, a series of reactions were demonstrated to occur during the DES treatment process. The performance and mechanism of methylene blue and rhodamine B adsorption on regenerated lignin were studied systematically, and the maximum adsorbed amounts were 348.29 and 551.05 mg/g at 323 K, respectively. This study provides a new strategy for the green preparation of functionalized lignin and its use in the water pollutant treatment.

Hierarchical Porous Aerogels With Multiple Adsorptive Interactions for Dye Wastewater Purification

Aerogels present a huge potential for removing organic dyes from printing and dyeing wastewater (PDW). However, the preparation of aerogels with multiple dye adsorption capabilities remains a challenge, as many existing aerogels are limited to adsorbing only a single type of dye. Herein, a composite aerogel (CG/T-rGO) with the addition of carboxymethyl chitosan, gelatin and tannic acid reduced graphene oxide (T-rGO) was synthesized by freeze-drying technology. The electrostatic interactions between dye molecular and GEL/CMCS (CG) networks, as well as the supramolecular interactions (H-bonds, electrostatic interactions and π-π stacks) between T-rGO, have endowed the aerogel with the ability to adsorb multiple types of dye, such as methylene blue (MB) and methyl orange (MO). Results exhibited that the prepared CG/T-rGO aerogel possessed strong mechanical strength and a porous 3D network structure with a porosity of 96.33 %. Using MB and MO as adsorbates, the adsorption capacity (88.2 mg/g and 66.6 mg/g, respectively) and the mechanism of the CG/T-rGO aerogel were investigated. The adsorption processes of aerogel for MB and MO were shown to follow the pseudo-second-order kinetic model and Langmuir isotherm model, indicating the chemical adsorption of a monolayer. The proposed aerogel in this work has promising prospects for dye removal from PDW.

Preparation of a Novel Lignocellulose-Based Aerogel by Partially Dissolving Medulla Tetrapanacis via Ionic Liquid

A novel lignocellulosic aerogel, MT-LCA, was successfully prepared from MT by undergoing partial dissolution in an ionic liquid, coagulation in water, freezing in liquid nitrogen, and subsequent freeze-drying. The MT-LCA preserves its original honeycomb-like porous structure, and the newly formed micropores contribute to increased porosity and specific surface area. FT-IR analysis reveals that MT, after dissolution and coagulation, experiences no chemical reactions. However, a change in the crystalline structure of cellulose is observed, transitioning from cellulose I to cellulose II. Both MT and MT-LCA demonstrate a quasi-second-order kinetic process during methylene blue adsorption, indicative of chemical adsorption. The Langmuir model proves to be more appropriate for characterizing the methylene blue adsorption process. Both adsorbents exhibit monolayer adsorption, and their effective adsorption sites are uniformly distributed. The higher porosity, nanoscale micropores, and larger pore size in MT-LCA enhance its capillary force, providing efficient directional transport performance. Consequently, the prepared MT-LCA displays exceptional compressive performance and efficient directional transport capabilities, making it well-suited for applications requiring high compressive performance and selective directional transport.

Superadsorbent aerogel based on sunflower stem pith cellulose and layered double hydroxides modified montmorillonite for methylene blue removal from water solution

Sunflower stem pith, an agricultural residue, was used as a starting material for the preparation of bio-based products. Sunflower stem pith nanocellulose (SSP-C) was prepared by sodium hydroxide/urea from the SSP cellulose. The prepared SSP-C was typical of cellulose II. To improve the adsorption capacity of the SSP-C, a bio-based aerogel (SSP-MH) with adsorbed methylene blue (MB) was prepared by compounding layered double hydroxides modified montmorillonite (MH) with SSP-C-based adsorbent, and the chemical characteristics and topology of the adsorbent were determined. The removal performance of SSP-MH in different MB concentrations was examined. Adsorption tests showed that hydrogels containing the same content of MH had higher removal efficiency. The removal rate of MB by SSP-MH was >87.5 % in MB solution (1 g/L), and its maximum adsorption capacity was 263.3 mg/g. The kinetics studies of MB removal were well by quasi-secondary adsorption kinetic model and Langmuir isotherm model. Moreover, the standard free Gibbs energy change of adsorption (ΔG0) was <0, which was favorable for adsorption of MB. The adsorption efficiency of SSP-MH on MB was still above 95 % by the five cycles of the adsorption/desorption experiment. The prepared samples were conducive to the high-value utilization of SSP.

Recent advances and future perspective on lignocellulose-based materials as adsorbents in diverse water treatment applications

The growing shortage of non-renewable resources and the burden of toxic pollutants in water have gradually become stumbling blocks in the path of sustainable human development. To this end, there has been great interest in finding renewable and environmentally friendly materials to promote environmental sustainability and combat harmful pollutants in wastewater. Of the many options, lignocellulose, as an abundant, biocompatible and renewable material, is the most attractive candidate for water remediation due to the unique physical and chemical properties of its constituents. Herein, we review the latest research advances in lignocellulose-based adsorbents, focusing on lignocellulosic composition, material modification, application of adsorbents. The modification and preparation methods of lignin, cellulose and hemicellulose and their applications in the treatment of diverse contaminated water are systematically and comprehensively presented. Also, the detailed description of the adsorption model, the adsorption mechanism and the adsorbent regeneration technique provides an excellent reference for understanding the underlying adsorption mechanism and the adsorbent recycling. Finally, the challenges and limitations of lignocellulosic adsorbents are evaluated from a practical application perspective, and future developments in the related field are discussed. In summary, this review offers rational insights to develop lignocellulose-based environmentally-friendly reactive materials for the removal of hazardous aquatic contaminants.

Nanocellulose-based composite aerogels toward the environmental protection: Preparation, modification and applications

Nanocellulose aerogel has the advantages of porosity, low density and high specific surface area, which can effectively realize the adsorption and treatment of wastewater waste gas. The methods of preparing nanocellulose mainly include mechanical, chemical and biological methods. Nanocellulose is formed into nanocellulose aerogel after gelation, solvent replacement and drying processes. Based on the advantages of easy modification of nanocellulose aerogels, nanocellulose aerogels can be functionalized with conductive fillers, reinforcing fillers and other materials to give nanocellulose aerogels in electrical, mechanical and other properties. Through functionalization, the properties of nanocellulose composite aerogel such as hydrophobicity and adsorption are improved, and the aerogel is endowed with the ability of electrical conductivity and electromagnetic shielding. Through functionalization, the applicability and general applicability of nanocellulose composite aerogel in the field of environmental protection are improved. In this paper, the preparation and functional modification methods of nanocellulose aerogels are reviewed, and the application prospects of nanocellulose composite aerogels in common environmental protection fields such as dye adsorption, heavy metal ion adsorption, gas adsorption, electromagnetic shielding, and oil-water separation are specifically reviewed, and new solutions are proposed.

Bacterial Cellulose Aerogels Derived from Pineapple Peel Waste for the Adsorption of Dyes

Valorization of pineapple peel waste is an attractive research topic because of the huge quantities of this byproduct generated from pineapple processing industries. In this study, the extract from pineapple waste was collected to produce a hydrogel-like form containing bacterial cellulose fibers with a three-dimensional structure and nanoscale diameter by the Acetobacter xylinum fermentation process. The bacterial cellulose suspension was subsequently activated by freeze-drying, affording lightweight aerogels as potential adsorbents in wastewater treatment, in particular the adsorptive removal of organic dyes. Intensive tests were carried out with the adsorption of methylene blue, a typical cationic dye, to investigate the influence of adsorption conditions (temperature, pH, initial dye concentration, time, and experiment scale) and aerogel-preparation parameters (grinding time and bacterial cellulose concentration). The bacterial cellulose-based aerogels exhibited high adsorption capacity not only for methylene blue but also for other cationic dyes, including malachite green, rhodamine B, and crystal violet (28-49 mg/g). However, its activity was limited for most of the anionic dyes, such as methyl orange, sunset yellow, and quinoline yellow, due to the repulsion of these anionic dyes with the aerogel surface, except for the case of congo red. It is also an anionic dye but has two amine groups providing a strong interaction with the hydroxyl group of the aerogel via hydrogen bonding. Indeed, the aerogel has a substantially large congo red-trapping capacity of 101 mg/g. Notably, the adsorption process exhibited similar performances, upscaling the solution volume to 50 times. The utilization of abundant agricultural waste in the simple aerogel preparation to produce a highly efficient and biodegradable adsorbent is the highlight of this work.

An ultralight and flexible nanofibrillated cellulose/chitosan aerogel for efficient chromium removal: Adsorption-reduction process and mechanism

Heavy metals in water are critical global environmental problems. In particular, the anionic heavy metal chromium (Cr) has carcinogenic and genotoxic risks on human health. To this end, an ultralight and flexible nanofibrillated cellulose (NFC)/chitosan (CS) aerogel was developed only by freeze-drying combined with physical thermal cross-linking for efficient one step co-removal of Cr(VI) and Cr(III). The maximum adsorption capacity of Cr(VI) and total Cr calculated according to the Langmuir model was 197.33 and 134.12 mg/g, respectively. Even in the presence of competing soluble organics, anions and oil contaminants, the resulting NFC/CS-5 aerogels showed excellent selectivity. The aerogel exhibited outstanding mechanical integrity, remaining intact after 17 compressions in air and underwater. Meanwhile, after 5 adsorption-desorption cycles, the aerogel was easy to regenerate and maintained a high regeneration efficiency of 80.25%. Importantly, self-assembled NFC/CS-5 aerogel filter connected with the peristaltic pump could purify 752 mL of industrial wastewater with Cr(VI) pre-concentration capacity of 49.71 mg/g. XPS and FT-IR verified that electrostatic interactions, reduction and complexation acted as the main driving forces for the adsorption process. Moreover, such aerogel possessed broad application prospects for alleviating heavy metal pollution in agriculture.

Covalent Crosslinking Cellulose/Graphene Aerogels with High Elasticity and Adsorbability for Heavy Metal Ions Adsorption

With the fast development of modern industry, heavy metal contaminant became more severe. How to remove heavy metal ions in water in a green and efficient way is a prominent problem in current environmental protection. The adsorption of cellulose aerogel as a novel heavy metal removal technology has many advantages, including abundant resources, environmental friendly, high specific surface, high porosities and without second pollution, which means it has a wide application prospect. Here, we reported a self-assembly and covalent crosslinking strategy to prepare elastic and porous cellulose aerogels using PVA and graphene and cellulose as precursor. The resulting cellulose aerogel had a low density of 12.31 mg cm^-3 and excellent mechanical properties, which can recover to its initial form at 80% compressive strain. Meanwhile, the cellulose aerogel had strong adsorption capacity of Cu²⁺ (80.12 mg g^-1), C_d²⁺ (102.23 mg g^-1), Cr³⁺ (123.02 mg g^-1), Co²⁺ (62.38 mg g^-1), Zn²⁺ (69.55 mg g^-1), and Pb²⁺ (57.16 mg g^-1). In addition, the adsorption mechanism of the cellulose aerogel was investigated using adsorption kinetics and adsorption isotherm, and the conclusion was that the adsorption process was mainly controlled by chemisorption mechanism. Therefore, cellulose aerogel, as a kind of green adsorption material, has a very high application potential in future water treatment applications.

Fibrous Aerogels with Tunable Superwettability for High-Performance Solar-Driven Interfacial Evaporation

Solar-driven interfacial evaporation is an emerging technology for water desalination. Generally, double-layered structure with separate surface wettability properties is usually employed for evaporator construction. However, creating materials with tunable properties is a great challenge because the wettability of existing materials is usually monotonous. Herein, we report vinyltrimethoxysilane as a single molecular unit to hybrid with bacterial cellulose (BC) fibrous network, which can be built into robust aerogel with entirely distinct wettability through controlling assembly pathways. Siloxane groups or carbon atoms are exposed on the surface of BC nanofibers, resulting in either superhydrophilic or superhydrophobic aerogels. With this special property, single component-modified aerogels could be integrated into a double-layered evaporator for water desalination. Under 1 sun, our evaporator achieves high water evaporation rates of 1.91 and 4.20 kg m-2 h-1 under laboratory and outdoor solar conditions, respectively. Moreover, this aerogel evaporator shows unprecedented lightweight, structural robustness, long-term stability under extreme conditions, and excellent salt-resistance, highlighting the advantages in synthesis of aerogel materials from the single molecular unit.

A facile approach to cellulose/multi-walled carbon nanotube gels-Structure, formation process and adsorption to methylene blue

In view of the deficiencies in the preparation of cellulose gels, such as, cumbersome process, harsh conditions, high consumption of chemicals, secondary pollution caused by side reactions, this work reports a facile approach to make cellulose/multi-walled carbon nanotube (MWCNTs) hydrogels and aerogels via mixing cellulose with N,N'-methylene bisacrylamide (MBA) and MWCNTs in NaOH/urea/H₂O aqueous solution. The gels were revealed to be formed by an addition reaction between the double bonds of MBA and the hydroxyl groups of cellulose and the intermolecular interactions between cellulose and MWCNTs. The preparation process can be realized at room temperature and atmospheric pressure without the intervention of ultrasonic dispersion, catalyst and initiator. The gelation time, puncture strength and water retention ability of the hydrogels were investigated. Results showed that, compared with pure cellulose hydrogel, cellulose/MWNCTs hydrogels have obviously shorter sol-gel transition time (124-129.2 min), higher puncture strength (29.6022-34.2854 KPa) and water retention ability (274.2619-301.7291 g/g). Cellulose/MWCNTs aerogels possessed three dimensional network with macroporous structure (about 500 μm), low density (0.00546-0.00557 g/cm³), high porosity (99.6360-99.6426 %), good thermal stability (242 °C) and certain absorbency to methylene blue (233.2901-242.1122 mg/g).

Polydopamine-Modified Cellulose Nanofibril Composite Aerogel: An Effective Dye Adsorbent

In this study, a new cellulose nanofibril (CNF) composite aerogel was fabricated using a green and facile mussel-inspired coating strategy. First, the CNF hydrogel was crosslinked by calcium ion followed by immersion in dopamine solution. Second, the surface of CNF was modified using polydopamine (PDA) to obtain PDA@CNF (PCNF) composite aerogel. The PCNF composite aerogels had large surface areas (368.15 m²/g) and low bulk density (27.2 mg/cm³). The composite aerogel exhibited improved mechanical properties, which were almost three times compared with those of CNF aerogel. Moreover, PCNF composite aerogel had good resilience under a wet state. The PDA functional layer remarkably enhanced the adsorption capacities of the composite aerogel for methylene blue (MB). The maximum adsorption of MB was 208 mg/g at an initial dye concentration of 50 mg/L. The adsorption isotherm and kinetic behaviors of the composite aerogel were consistent with Langmuir and pseudo-second-order models. In addition, the PCNF composite aerogels had a high adsorption capacity over a wide pH range. The reuse experiment showed that the removal efficiency of the composite aerogel remained higher than 85% after five cycles. Therefore, PCNF composite aerogels may have potential application in wastewater treatment due to its environmental sustainability and low energy consumption.

One-Step Fabrication of Novel Polyethersulfone-Based Composite Electrospun Nanofiber Membranes for Food Industry Wastewater Treatment

Using an environmentally friendly approach for eliminating methylene blue from an aqueous solution, the authors developed a unique electrospun nanofiber membrane made of a combination of polyethersulfone and hydroxypropyl cellulose (PES/HPC). SEM results confirmed the formation of a uniformly sized nanofiber membrane with an ultrathin diameter of 168.5 nm (for PES/HPC) and 261.5 nm (for pristine PES), which can be correlated by observing the absorption peaks in FTIR spectra and their amorphous/crystalline phases in the XRD pattern. Additionally, TGA analysis indicated that the addition of HPC plays a role in modulating their thermal stability. Moreover, the blended nanofiber membrane exhibited better mechanical strength and good hydrophilicity (measured by the contact angle). The highest adsorption capacity was achieved at a neutral pH under room temperature (259.74 mg/g), and the pseudo-second-order model was found to be accurate. In accordance with the Langmuir fitted model and MB adsorption data, it was revealed that the adsorption process occurred in a monolayer form on the membrane surface. The adsorption capacity of the MB was affected by the presence of various concentrations of NaCl (0.1–0.5 M). The satisfactory reusability of the PES/HPC nanofiber membrane was revealed for up to five cycles. According to the mechanism given for the adsorption process, the electrostatic attraction was shown to be the most dominant in increasing the adsorption capacity. Based on these findings, it can be concluded that this unique membrane may be used for wastewater treatment operations with high efficiency and performance.

Environment-friendly degradable zinc-ion battery based on guar gum-cellulose aerogel electrolyte

With the vigorous development of electronics and the increasingly prominent problem of environmental pollution, it is particularly important to exploit environmentally friendly electronic devices. Transient electronics represent a kind of device that once the specified functions have completed can completely or partially disappear through physical or chemical actions. In this work, we introduce a novel guar gum-cellulose aerogel (GCA) membrane based on natural biomaterials and successfully use it as an electrolyte film to fabricate a degradable zinc-ion battery (DZIB). All components of the prepared DZIBs can be successfully degraded or disintegrate in phosphate-buffered saline (PBS) containing a solution of proteinase K after approximately 40 days. This electrolyte film has a high ionic conductivity of approximately 4.73 × 10^-2 S cm^-1 and a good mechanical stress property. When applied to DZIB, the production of zinc dendrites can be restrained, leading to the battery showing excellent electrochemical performance. The battery exhibits a specific capacity of 309.1 mA h g^-1 at a current density of 308 mA g^-1 after 100 cycles and a steady cycling ability (100% capacity retention after 200 cycles). More importantly, the electrochemical performance of DZIB is better than that of transient batteries reported in the past, taking a solid step in the field of transient electronics in the initial stage.

Cellulose Nanofiber-Based Aerogels from Wheat Straw: Influence of Surface Load and Lignin Content on Their Properties and Dye Removal Capacity

Water pollution is one of the most serious problems worldwide. Nanocellulose-based aerogels usually show excellent adsorption capacities due to their high aspect ratio, specific surface area and surface charge, making them ideal for water purification. In this work, (ligno)cellulose nanofibers (LCNFs/CNFs) from wheat straw residues were obtained using two types of pre-treatments: mechanical (Mec) and TEMPO-mediated oxidization (TO), to obtain different consistency (0.2, 0.4, 0.6 and 0.8) bioaerogels, and their adsorption capacities as dye removers were further studied. The materials were characterized in terms of density, porosity and mechanical properties. An inversely proportional relationship was observed between the consistencies of the aerogels and their achieved densities. Despite the increase in density, all samples showed porosities above 99%. In terms of mechanical properties, the best results were obtained for the 0.8% consistency LCNF and CNF-Mec aerogels, reaching 67.87 kPa and 64.6 kPa for tensile strength and Young’s modulus, respectively. In contrast, the adsorption capacity of the aerogels was better for TEMPO-oxidized aerogels, reaching removal rates of almost 100% for the CNF-TO5 samples. Furthermore, the residual lignin content in LCNF-Mec aerogels showed a great improvement in the removal capacity, reaching rates higher than 80%, further improving the cost efficiency of the samples due to the reduction in chemical treatments.

Nanocellulose and Graphene Oxide Aerogels for Adsorption and Removal Methylene Blue from an Aqueous Environment

The characteristics of aerogel materials such as the low density and large surface area enable them to adsorb large amounts of substances, so they show great potential for application in industrial wastewater treatment. Herein, using a combination of completely environmentally friendly materials such as cellulose nanofibers (CNFs) extracted from the petioles of the nipa palm tree and graphene oxide (GO) fabricated by simple solvent evaporation, a composite aerogel was prepared by a freeze-drying method. The obtained aerogel possessed a light density of 0.0264 g/cm3 and a porosity of more than 98.2%. It was able to withstand a weight as much as 2500 times with the maximum force (1479.5 N) to break up 0.2 g of an aerogel by compression strength testing and was stable in the aquatic environment, enabling it to be reused five times with an adsorption capacity over 90%. The CNF/GO aerogel can recover higher than 85% after 30 consecutive compression recovery cycles, which is convenient for the reusability of this material in wastewater treatments. The obtained aerogel also showed a good interaction between the component phases, a high thermal stability, a 3D network structure combined with thin walls and pores with a large specific surface area. In addition, the aerogel also exhibited a fast adsorption rate for methylene blue (MB) adsorption, a type of waste from the textile industry that pollutes water sources, and it can adsorb more than 99% MB in water in less than 20 min. The excellent adsorption of MB onto the CNF/GO aerogel was driven by electrostatic interactions, which agreed with the pseudo-second-order kinetic model with a correlation coefficient R 2 = 0.9978. The initial results show that the CNF/GO aerogel is a highly durable "green" light material that might be applied in the treatment of domestic organic waste water and is completely recoverable and reusable.

Liquid Transport and Real-Time Dye Purification via Lotus Petiole-Inspired Long-Range-Ordered Anisotropic Cellulose Nanofibril Aerogels

Nowadays, large-scale oriented functional porous materials have been sought after by researchers. However, regulation of the long-range uniform and oriented structures of the material remains a challenge. Herein, ultralong anisotropic cellulose nanofibril (CNF) aerogels with uniformly ordered structures of pore walls inspired by lotus petioles were constructed by applying external speeds to counterbalance the growth driving forces of ice crystals. Based on the growth law of ice crystals, the ice crystals grew at a stable rate when the applied external speed was 0.04 mm/s, ensuring the consistent orientation of the large-scale CNF aerogel. The aerogel exhibited a rapid long-range directional transport ability to different liquid solvents, delivering ethanol up to 40 mm from bottom to top within 50 s. Moreover, by introducing rectorites with good cation-exchange properties, the resulting long-range composite possessed an enhanced adsorption capacity for methylene blue. Furthermore, aerogel successfully achieved real-time dye purification at a long distance, such as fast dye adsorption or selective adsorption. This flexible and straightforward strategy of fabricating ultralong oriented CNF aerogel materials is expected to promote the development of functional aerogels in directional liquid transport and sewage treatment.