Enhanced ethanol sensing performance of N-doped ZnO derived from ZIF-8

Enhanced sorption and fluorescent detection of bisphenol A by using sodium alginate/cellulose nanofibrils/ZIF-8 composite hydrogel

To address the issue of bisphenol A (BPA) contamination in wastewater, a novel hydrogel, sodium alginate/cellulose nanofibrils/ZIF-8 composite hydrogel (SCZC), was synthesized for efficient BPA removal. The SCZC exhibited an exceptional adsorption capacity of 1696 mg/g, aligning well with both Langmuir and pseudo-second-order models. Furthermore, it exhibited remarkable regeneration properties, maintaining 89.1 % of its adsorption capacity even after undergoing five adsorption-desorption cycles. The synthesized SCZC also acted as a fluorescent sensor for detecting BPA, employing dynamic quenching and offering linear detection ranges of 10-100 mg/L and 0.2-1.0 μg/L, with a low detection limit of 0.06 μg/L. Analysis of adsorption and detection mechanisms revealed that SCZC's exceptional performance could be attributed to the three-dimensional (3D) porous structure formed by sodium alginate and cellulose nanofibrils. Economic analysis indicated that SCZC, in comparison to commercially activated carbon, was relatively inexpensive. This study introduces a novel approach for designing and preparing a sodium alginate-based hydrogel incorporating metal-organic frameworks, offering simultaneous BPA detection and removal capabilities.

Full-Spectrum Utilization of ZIF-67/Ag NPs/NaYF4:Yb,Er Photocatalysts for Efficient Degradation of Sulfadiazine: Upconversion Mechanism and DFT Calculation

In this work, novel ternary composite ZIF-67/Ag NPs/NaYF4:Yb,Er is synthesized by solvothermal method. The photocatalytic activity of the composite is evaluated by sulfadiazine (SDZ) degradation under simulated sunlight. High elimination efficiency of the composite is 95.4% in 180 min with good reusability and stability. The active species (h+, ·O2 - and ·OH) are identified. The attack sites and degradation process of SDZ are deeply investigated based on theoretical calculation and liquid chromatography-mass spectrometry analysis. The upconversion mechanism study shows that favorable photocatalytic effectiveness is attributed to the full utilization of sunlight through the energy transfer upconversion process and fluorescence resonance energy transfer. Additionally, the composite is endowed with outstanding light-absorbing qualities and effective photogenerated electron-hole pair separation thanks to the localized surface plasmon resonance effect of Ag nanoparticles. This work can motivate further design of novel photocatalysts with upconversion luminescence performance, which are applied to the removal of sulphonamide antibiotics in the environment.

In Situ-Derived N-Doped ZnO from ZIF-8 for Enhanced Ethanol Sensing in ZnO/MEMS Devices

Microelectromechanical systems (MEMS) gas sensors have numerous advantages such as compact size, low power consumption, ease of integration, etc., while encountering challenges in sensitivity and high resistance because of their low sintering temperature. This work utilizes the in situ growth of Zeolitic Imidazolate Framework-8 (ZIF-8) followed by its conversion to N-doped ZnO. The results obtained from scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicate that the in situ derivation of ZIF-8 facilitates the adhesion of ZnO particles, forming an island-like structure and significantly reducing the interfaces between these particles. Furthermore, powder X-ray diffraction (XRD) analysis, elemental mapping, and X-ray photoelectron spectroscopy (XPS) analysis confirm the conversion of ZIF-8 to ZnO, the successful incorporation of N atoms into the ZnO lattice, and the creation of more oxygen vacancies. The ZIF-8-derived N-doped ZnO/MEMS sensor (ZIF (3)-ZnO/MEMS) exhibits remarkable gas sensitivity for ethanol detection. At an operating temperature of 290 °C, it delivers a substantial response value of 80 towards 25 ppm ethanol, a 13-fold enhancement compared with pristine ZnO/MEMS sensors. The sensor also exhibits an ultra-low theoretical detection limit of 11.5 ppb to ethanol, showcasing its excellent selectivity. The enhanced performance is attributed to the incorporation of N-doped ZnO, which generates abundant oxygen vacancies on the sensor's surface, leading to enhanced interaction with ethanol molecules. Additionally, a substantial two-order-of-magnitude decrease in the resistance of the gas-sensitive film is observed. Overall, this study provides valuable insights into the design and fabrication strategies applicable to high-performance MEMS gas sensors in a broader range of gas sensing.

ZIF-67 based CoS2 self-assembled on graphitic carbon nitride microtubular for sensitive electrochemical detection of paraquat in fruits

Paraquat (PQ) is a widely used and harmful herbicide that must be detected in the environment. This study reports a novel composite (CoS2-GCN) prepared by assembling cobalt disulfide (CoS2) derived from metal-organic frameworks (MOFs) on graphitic carbon nitride (GCN). An electrochemical sensor (CoS2-GCN/ glassy carbon electrode (GCE)) was successfully prepared by modifying CoS2-GCN onto a GCE to sensitively detect PQ. Different concentrations of PQ were detected using square-wave voltammetry, and the CoS2-GCN/GCE electrochemical sensor showed remarkable response signals for PQ in the range of 20 - 1000 nM and 1 - 13 μM, with a detection limit of 4.13 nM (S/N = 3). The CoS2-GCN/GCE electrochemical sensor exhibited high stability, reproducibility, and immunity to interference, which were attributed to the synergistic effects of CoS2 and GCN. In addition, the CoS2-GCN/GCE electrochemical sensor showed high applicability for the analysis of fruit samples. Therefore, the proposed sensor has potential applications in PQ detection.

Study on the Photocatalytic Properties of Metal-Organic Framework-Derived C-, N-Co-Doped ZnO

In this study, C- and N-co-doped ZnO photocatalysts were prepared through pyrolysis using metal-organic frameworks (MOFs) as precursor materials. The crystal structure, morphology, and surface chemical composition of the samples were characterised via X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Their activities in photocatalytic reactions were also evaluated through photocatalytic experiments. The results show that C-, N-co-doped ZnO has a high specific surface area, which is favourable for a photocatalytic reaction. Meanwhile, C-, N-doping can effectively modulate the energy band structure of ZnO, broaden its light absorption range, and improve the separation efficiency of photogenerated electron-hole pairs. The photocatalytic experiments show that the C/N-ZnO-500 samples, which have the optimal photocatalytic performances, have improved performances of 50% and 35%, respectively, compared with those of the blank control group and the ZIF-8 samples. The preparation of ZnO materials with a morphology change and doping using metal frameworks as precursors provides a new idea for designing efficient photocatalysts.

Three-dimensional rose-like zinc oxide fiber coating for simultaneous extraction of polychlorinated biphenyls and polycyclic aromatic hydrocarbons by headspace solid phase microextraction

The three-dimensional (3D) rose-like zinc oxide (ZnO) material was prepared by a simple one-step CTAB-assisted hydrothermal strategy and used as a headspace solid-phase microextraction (HS-SPME) coating. Polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) were analyzed by gas chromatography with flame ionization detector (GC-FID), and conclusively applied to ultrasensitive detection in lake and river water. Compared with one-dimensional (1D) pencil-like ZnO, the layer-by-layer petal-like structure could fully expose mass adsorption sites on the surface, which could significantly improve the adsorption. The enrichment factors with 7535-8595 for PCBs and 3855-7320 for PAHs were achieved. The established method provided a satisfactory linear range (0.005-30 ng·mL-1), coefficient (R2 > 0.9978), ultra-low limit detection (1-3 pg·mL-1), and long service life (≥ 150 times). The recoveries of 83.42-120.86 % were obtained in the real detection application of lake and river water. This work demonstrated that 3D rose-like ZnO with low cost, simple synthesis, fast extraction ability and high enrichment performance was an ideal coating material, which was hoped to enrich other compounds with similar structures with PCBs and PAHs.

Delafossite CuCoO2/ZnO derived from ZIF-8 heterojunctions as efficient photoelectrodes for dye-sensitized solar cells

To achieve high-performance dye-sensitized solar cells (DSSCs), it is essential to establish new and effective photoelectrode materials. Herein, we report the successful synthesis of heterojunctions including Cu-based delafossite oxide CuCoO2 and ZnO derived from zeolitic imidazolate framework-8 (ZIF-8). The layered polyhedral nanocrystals of CuCoO2 produced through a feasible low temperature hydrothermal process and the faceted nanocrystals of ZnO were achieved by heat treatment of ZIF-8. The composite heterostructures were applied as photoelectrodes in DSSCs assembled using dye N719 and a Pt counter electrode. The physicochemical characteristics (XRD, FESEM, EDAX, mapping, BET, DRS), dye loading, and photovoltaic properties (J-V, EIS, IPCE) of the fabricated materials were studied and fully discussed. Results revealed that addition of CuCoO2 to ZnO significantly improved the Voc, Jsc, PCE, FF, and IPCE. Among all cells, CuCoO2/ZnO (0.1 : 1) showed the best performance (PCE = 6.27%, Jsc = 14.56 mA cm-2, Voc = 687.84 mV, FF = 62.67%, IPCE = 45.22%) and acted as a promising photoanode in DSSCs.