Kinetic model of wet oxidation of phenol at basic pH using a copper catalyst

Synthesis, Characterization of Magnetic Composites and Testing of Their Activity in Liquid-Phase Oxidation of Phenol with Oxygen

The development and improvement of methods for the synthesis of environmentally friendly catalysts based on base metals is currently an urgent and promising task of modern catalysis. Catalysts based on nanoscale magnetite and maghemite have fast adsorption–desorption kinetics and high chemical activity. The purpose of this work is to obtain magnetic composites, determine their physicochemical characteristics and verify their activity in the process of liquid-phase oxidation of phenol with oxygen. Magnetic nanocomposites were obtained by chemical co-deposition of salts of ferrous and trivalent iron. The synthesized magnetic composites were studied by X-ray diffractometry, energy dispersive X-ray fluorescence and Mössbauer spectroscopy, IR-Fourier spectroscopy and elemental analysis. To increase the catalytic activity in oxidative processes, the magnetite surfaces were modified using cobalt nitrate salt. Further, CoFe2O4 was stabilized by adding polyethylenimine (PEI) as a surfactant. Preliminary studies of the oxidation of phenol with oxygen, as the most typical environmental pollutant were carried out on the obtained Fe3O4, CoFe2O4, CoFe2O4/PEI catalysts. The spectrum of the reaction product shows the presence of CH in the aromatic ring and double C=C bonds, stretching vibrations of the C=O groups of carbonyl compounds; the band at 3059 cm−1 corresponds to the presence of double C=C bonds and the band at 3424 cm−1 to hydroquinone compounds. The band at 1678 cm−1 and the intense band at 1646 cm−1 refer to vibrations of the C=O bonds of the carbonyl group of benzoquinone. Peaks at 1366 cm−1 and 1310 cm−1 can be related to the vibrations of C–H and C–C bonds of the quinone ring. Thus, it was demonstrated that produced magnetic composites based on iron oxide are quite effective in the oxidation of phenol with oxygen.

Origin and Perspectives of the Photochemical Activity of Nanoporous Carbons

Even though, owing to the complexity of nanoporous carbons' structure and chemistry, the origin of their photoactivity is not yet fully understood, the recent works addressed here clearly show the ability of these materials to absorb light and convert the photogenerated charge carriers into chemical reactions. In many aspects, nanoporous carbons are similar to graphene; their pores are built of distorted graphene layers and defects that arise from their amorphicity and reactivity. As in graphene, the photoactivity of nanoporous carbons is linked to their semiconducting, optical, and electronic properties, defined by the composition and structural defects in the distorted graphene layers that facilitate the exciton splitting and charge separation, minimizing surface recombination. The tight confinement in the nanopores is critical to avoid surface charge recombination and to obtain high photochemical quantum yields. The results obtained so far, although the field is still in its infancy, leave no doubts on the possibilities of applying photochemistry in the confined space of carbon pores in various strategic disciplines such as degradation of pollutants, solar water splitting, or CO2 mitigation. Perhaps the future of photovoltaics and smart-self-cleaning or photocorrosion coatings is in exploring the use of nanoporous carbons.

Recent advances in nanomaterials for water protection and monitoring

Nanomaterials (NMs) for adsorption, catalysis, separation, and disinfection are scrutinized. NMs-based sensor technologies and environmental transformations of NMs are highlighted.

Carbon foams as catalyst supports for phenol photodegradation

A carbon foam using coal tar pitch as precursor was prepared and investigated as support for titanium oxide for the photocatalytic degradation of phenol. The performance of the carbon foam/titania composite was compared to those of unsupported titania and other activated carbon composites from the literature. The photodegradation rate of phenol over the catalysts under UV illumination was fitted to the Langmuir-Hinshelwood model; data showed that the apparent rate constant of the carbon foam supported titania was almost three times larger than that of bare titania, and comparable to that of other carbon supported composites. Considering the low porous features of the carbon foam, this suggests that large surface area supports are not essential to achieve high degradation rates and efficiencies. Moreover, when titania is supported on the carbon foam large amounts of catechol are detected in solution after UV irradiation, indicating a better degradation efficiency.

Electrochemically enhanced adsorption of phenol on activated carbon fibers in basic aqueous solution

Electrosorption isotherms and thermodynamics of phenol on activated carbon fibers (ACFs) in basic solution, as well as the factors (bias potential, initial concentration, and electrolyte) affecting adsorption/electrosorption kinetics, were investigated. The kinetics, which followed the Lagergren adsorption rate law, exhibited a variety of responses depending on bias potential, initial concentration, and electrolyte. The electrosorption isotherms were in agreement with the classical models of Langmuir and Freundlich, but the former gave more satisfactory correlation coefficients. With electrosorption at a bias potential of 700 mV from the basic solution, a nearly 10-fold enhancement of maximum adsorption capacity was achievable. The electrosorption free energy (DeltaG(ads)), enthalpy (DeltaH(ads)), and entropy (DeltaS(ads)) of phenol on the ACFs were calculated from adsorption isotherms at different temperatures. The results indicated that electrosorption of phenol in basic solution was spontaneous and exothermic. Furthermore, it was assessed that electrosorption occurred by dipole-dipole interaction with DeltaH(ads) of -20.14 kJ mol(-1) besides suppositional electrostatic interaction.