Catalytic nanoliths

Subnanometer cobalt oxide clusters as selective low temperature oxidative dehydrogenation catalysts

The discovery of more efficient, economical, and selective catalysts for oxidative dehydrogenation is of immense economic importance. However, the temperatures required for this reaction are typically high, often exceeding 400 °C. Herein, we report the discovery of subnanometer sized cobalt oxide clusters for oxidative dehydrogenation of cyclohexane that are active at lower temperatures than reported catalysts, while they can also eliminate the combustion channel. These results found for the two cluster sizes suggest other subnanometer size (CoO)_x clusters will also be active at low temperatures. The high activity of the cobalt clusters can be understood on the basis of density functional studies that reveal highly active under-coordinated cobalt atoms in the clusters and show that the oxidized nature of the clusters substantially decreases the binding energy of the cyclohexene species which desorb from the cluster at low temperature.

Current oxidative dehydrogenation processes are based on petroleum cracking that is indirect, environmentally unfriendly, and energy intensive. Here, the authors discover that subnanometer sized cobalt oxide clusters are active for oxidative dehydrogenation of cyclohexane at lower temperatures than reported catalysts.

Preparation and morphology-dependent wettability of porous alumina membranes

This article presents the preparation and study of the wetting properties of porous alumina membranes (PAMs) with a thickness of 25 to 75 μm and with a different pore sizes. The fabrication process features, scanning electron microscopy and atomic force microscopy characterization results are presented. The comparative analysis of PAM surfaces (outer and inner) and the effect of morphology of these surfaces on the wetting properties are discussed. Both alumina surfaces show significant morphology-dependent wettability. Measurements of the interfacial contact angle were made on the as-fabricated amorphous membrane and after pore widening with a range of pore diameters from 25 to 100 nm. The possible applications of PAMs for various membrane technologies is shown.

ZnO modified ZSM-5 and Y zeolites fabricated by atomic layer deposition for propane conversion

Zeolite supported highly dispersed ZnO fabricated by ALD is an effective catalyst for conversion of propane to propylene and aromatics.

Parallel array of nanochannels grafted with polymer-brushes-stabilized Au nanoparticles for flow-through catalysis

Smart systems on the nanometer scale for continuous flow-through reaction present fascinating advantages in heterogeneous catalysis, in which a parallel array of straight nanochannels offers a platform with high surface area for assembling and stabilizing metallic nanoparticles working as catalysts. Herein we demonstrate a method for finely modifying the nanoporous anodic aluminum oxide (AAO), and further integration of nanoreactors. By using atomic transfer radical polymerization (ATRP), polymer brushes were successfully grafted on the inner wall of the nanochannels of the AAO membrane, followed by exchanging counter ions with a precursor for nanoparticles (NPs), and used as the template for deposition of well-defined Au NPs. The membrane was used as a functional nanochannel for novel flow-through catalysis. High catalytic performance and instantaneous separation of products from the reaction system was achieved in reduction of 4-nitrophenol.

Nanostraws for direct fluidic intracellular access

Nanomaterials are promising candidates to improve the delivery efficiency and control of active agents such as DNA or drugs directly into cells. Here we demonstrate cell-culture platforms of nanotemplated "nanostraws" that pierce the cell membrane, providing a permanent fluidic pipeline into the cell for direct cytosolic access. Conventional polymeric track-etch cell culture membranes are alumina coated and etched to produce fields of nanostraws with controllable diameter, thickness, and height. Small molecules and ions were successfully transported into the cytosol with 40 and 70% efficiency, respectively, while GFP plasmids were successfully delivered and expressed. These platforms open the way for active, reproducible delivery of a wide variety of species into cells without endocytosis.

In situ monitoring of atomic layer deposition in nanoporous thin films using ellipsometric porosimetry

Ellipsometric porosimetry (EP) is a handy technique to characterize the porosity and pore size distribution of porous thin films with pore diameters in the range from below 1 nm up to 50 nm and for the characterization of porous low-k films especially. Atomic layer deposition (ALD) can be used to functionalize porous films and membranes, e.g., for the development of filtration and sensor devices and catalytic surfaces. In this work we report on the implementation of the EP technique onto an ALD reactor. This combination allowed us to employ EP for monitoring the modification of a porous thin film through ALD without removing the sample from the deposition setup. The potential of in situ EP for providing information about the effect of ALD coating on the accessible porosity, the pore radius distribution, the thickness, and mechanical properties of a porous film is demonstrated in the ALD of TiO(2) in a mesoporous silica film.

Biomimetic synthesis of hierarchically porous nanostructured metal oxide microparticles--potential scaffolds for drug delivery and catalysis

Hierarchically porous hybrid microparticles, strikingly reminiscent in their structure of the silica skeletons of single-cell algae, diatoms, but composed of titanium dioxide, and the chemically bound amphiphilic amino acids or small proteins can be prepared by a simple one-step biomimetic procedure, using hydrolysis of titanium alkoxides modified by these ligands. The growth of the hierarchical structure results from the conditions mimicking the growth of skeletons in real diatoms--the self-assembly of hydrolysis-generated titanium dioxide nanoparticles, templated by the microemulsion, originating from mixing the hydrocarbon solvent and water on action of amino acids as surfactants. The obtained microsize nanoparticle aggregates possess remarkable chemical and thermal stability and are promising substrates for applications in drug delivery and catalysis. They can be provided with pronounced surface chirality through application of chiral modifying ligands. They display also high selectivity in sorption of phosphorylated biomolecules or medicines as demonstrated by (1)H and (31)P NMR studies and by in vitro modeling using (32)P-marked ATP as a substrate. The release of the adsorbed model compounds in an inert medium is a very slow process directed by desorption kinetics. It is enhanced, however, noticeably in contact with biological fluids modeling those of the tissues suffering inflammation, which makes the produced material highly attractive for application in medical implants. The developed synthetic approach has been applied successfully also for the preparation of analogous hybrid microparticles based on zirconium dioxide or aluminum sesquioxide.

Electrical transport through single-wall carbon nanotube-anodic aluminum oxide-aluminum heterostructures

Aluminum foils were anodized in sulfuric acid solution to form thick porous anodic aluminum oxide (AAO) films of thickness approximately 6 microm. Electrodes of carboxyl-functionalized single-wall carbon nanotube (SWCNT) thin films were inkjet printed on the anodic oxide layer and the electrical characteristics of the as-obtained SWCNT-AAO-Al structures were studied. Nonlinear current-voltage transport and strong temperature dependence of conduction through the structure was measured. The microstructure and chemical composition of the anodic oxide layer was analyzed using transmission and scanning electron microscopy as well as x-ray photoelectron spectroscopy. Schottky emission at the SWCNT-AAO and AAO-Al interfaces allowed by impurity states in the anodic aluminum oxide film together with ionic surface conduction on the pore walls of AAO gives a reasonable explanation for the measured electrical conduction. Calcined AAO is proposed as a dielectric material for SWCNT-field effect transistors.