Compositional analysis of the gas phase for the CO2+N2+tetra-n-butylammonium bromide aqueous solution systems under hydrate stability conditions

Hydrates for Cold Storage: Formation Characteristics, Stability, and Promoters

The potential of hydrates formed from R141b (CH3CCl2F), trimethylolethane (TME), and tetra-n-butylammonium bromide/tetra-n-butylammonium chloride (TBAB/TBAC) to be used as working substances for cold storage was investigated to provide a solution for unbalanced energy grids. In this study, the characteristics of hydrate formation, crystal morphology of hydrates, and the stability of hydrate in cyclic formation under 0.1 MPa and at 5 °C were carried out. It found that the ice had a positive effect on the hydrate formation under same conditions. Upon the addition of the ice cube, the induction time of R141b, TME, and TBAB/TBAC hydrates decreased markedly, and significantly high formation rates were obtained. Under magnetic stirring, the rate at which TBAB/TBAC formed hydrates was significantly lower than that when ice was used. In microscopic experiments, it was observed that the TBAB/TBAC mixture formed hydrates with more nucleation sites and compact structures, which may increase the hydrate formation rate. In the multiple cycle formation of TBAB/TBAC hydrates, the induction time gradually decreased with the increasing number of formation cycles and finally stabilized, which indicated the potential of the TBAB/TBAC hydrates for application in cold storage owing to their good durability and short process time for heat absorption and release.

Thermodynamic and kinetic verification of tetra-n-butyl ammonium nitrate (TBANO3) as a promoter for the clathrate process applicable to precombustion carbon dioxide capture

In this study, tetra-n-butyl ammonium nitrate (TBANO3) is evaluated as a promoter for precombustion capture of CO2 via hydrate formation. New hydrate phase equilibrium data for fuel gas (CO2/H2) mixture in presence of TBANO3 of various concentrations of 0.5, 1.0, 2.0, 3.0, and 3.7 mol % was determined and presented. Heat of hydrate dissociation was calculated using Clausius-Clapeyron equation and as the concentration of TBANO3 increases, the heat of hydrate dissociation also increases. Kinetic performance of TBANO3 as a promoter at different concentrations was evaluated at 6.0 MPa and 274.2 K. Based on induction time, gas uptake, separation factor, hydrate phase CO2 composition, and rate of hydrate growth, 1.0 mol % TBANO3 solution was found to be the optimum concentration at the experimental conditions of 6.0 MPa and 274.2 K for gas hydrate formation. A 93.0 mol % CO2 rich stream can be produced with a gas uptake of 0.0132 mol of gas/mol of water after one stage of hydrate formation in the presence of 1.0 mol % TBANO3 solution. Solubility measurements and microscopic images of kinetic measurements provide further insights to understand the reason for 1.0 mol % TBANO3 to be the optimum concentration.

CO2 hydrate formation and dissociation in cooled porous media: a potential technology for CO2 capture and storage

The purpose of this study was to investigate the hydrate formation and dissociation with CO2 flowing through cooled porous media at different flow rates, pressures, temperatures, and flow directions. CO2 hydrate saturation was quantified using the mean intensity of water. The experimental results showed that the hydrate block appeared frequently, and it could be avoided by stopping CO2 flooding early. Hydrate formed rapidly as the temperature was set to 274.15 or 275.15 K, but the hydrate formation delayed when it was 276.15 K. The flow rate was an important parameter for hydrate formation; a too high or too low rate was not suitable for CO2 hydration formation. A low operating pressure was also unacceptable. The gravity made hydrate form easily in the vertically upward flow direction. The pore water of the second cycle converted to hydrate more completely than that of the first cycle, which was a proof of the hydrate "memory effect". When the pressure was equal to atmospheric pressure, hydrate did not dissociate rapidly and abundantly, and a long time or reduplicate depressurization should be used in industrial application.

CO2 capture from simulated fuel gas mixtures using semiclathrate hydrates formed by quaternary ammonium salts

In order to investigate the feasibility of semiclathrate hydrate-based precombustion CO2 capture, thermodynamic, kinetic, and spectroscopic studies were undertaken on the semiclathrate hydrates formed from a fuel gas mixture of H2 (60%) + CO2 (40%) in the presence of quaternary ammonium salts (QASs) such as tetra-n-butylammonium bromide (TBAB) and fluoride (TBAF). The inclusion of QASs demonstrated significantly stabilized hydrate dissociation conditions. This effect was greater for TBAF than TBAB. However, due to the presence of dodecahedral cages that are partially filled with water molecules, TBAF showed a relatively lower gas uptake than TBAB. From the stability condition measurements and compositional analyses, it was found that with only one step of semiclathrate hydrate formation with the fuel gas mixture from the IGCC plants, 95% CO2 can be enriched in the semiclathrate hydrate phase at room temperature. The enclathration of both CO2 and H2 in the cages of the QAS semiclathrate hydrates and the structural transition that results from the inclusion of QASs were confirmed through Raman and (1)H NMR measurements. The experimental results obtained in this study provide the physicochemical background required for understanding selective partitioning and distributions of guest gases in the QAS semiclathrate hydrates and for investigating the feasibility of a semiclathrate hydrate-based precombustion CO2 capture process.