C2 yield enhancement during oxidative coupling of methane in a nonpermselective porous membrane reactor

Synthesis and Characterization of Silica-Tantala Microporous Membranes for Gas Separations Fabricated Using Chemical Vapor Deposition

Composite membranes consisting of microporous tantalum-doped silica layers supported on mesoporous alumina substrates were fabricated using chemical vapor deposition (CVD) in both thermal decomposition and counter-flow oxidative deposition modes. Tetraethyl orthosilicate (TEOS) was used as the silica precursor and tantalum (V) ethoxide (TaEO) as the tantalum source. Amounts of TaEO from 0 mol% to 40 mol% were used in the CVD gas mixture and high H₂ permeances above 10^-7 mol m^-2 s^-1 Pa^-1 were obtained for all conditions. Close examination was made of the H₂/CH₄ and O₂/CH₄ selectivities due to the potential use of these membranes in methane reforming or partial oxidation of methane applications. Increasing deposition temperature correlated with increasing H₂/CH₄ selectivity at the expense of O₂/CH₄ selectivity, suggesting a need to optimize membrane synthesis for a specific selectivity. Measured at 400 °C, the highest H₂/CH₄ selectivity of 530 resulted from thermal CVD at 650 °C, whereas the highest O₂/CH₄ selectivity of 6 resulted from thermal CVD at 600 °C. The analysis of the membranes attempted by elemental analysis, X-ray photoelectron spectroscopy, and X-ray absorption near-edge spectroscopy revealed that Ta was undetectable because of instrumental limitations. However, the physical properties of the membranes indicated that the Ta must have been present at least at dopant levels. It was found that the pore size of the resultant membranes increased from 0.35 nm for pure Si to 0.37 nm for a membrane prepared with 40 mol% Ta. Similarly, an increase in Ta in the feed resulted in an increase in O₂/CH₄ selectivity at the expense of H₂/CH₄ selectivity. Additionally, it resulted in a decrease in hydrothermal stability, with the membranes prepared with higher Ta suffering greater permeance and selectivity declines during 96 h of exposure to 16 mol% H₂O in Ar at 650 °C.

Oxidative Coupling of Methane for Ethylene Production: Reviewing Kinetic Modelling Approaches, Thermodynamics and Catalysts

Ethylene production via oxidative coupling of methane (OCM) represents an interesting route for natural gas upscaling, being the focus of intensive research worldwide. Here, OCM developments are analysed in terms of kinetic mechanisms and respective applications in chemical reactor models, discussing current challenges and directions for further developments. Furthermore, some thermodynamic aspects of the OCM reactions are also revised, providing achievable olefins yields in a wide range of operational reaction conditions. Finally, OCM catalysts are reviewed in terms of respective catalytic performances and thermal stability, providing an executive summary for future studies on OCM economic feasibility.

Experimental Investigation of the Oxidative Coupling of Methane in a Porous Membrane Reactor: Relevance of Back-Permeation

Novel reactor configurations for the oxidative coupling of methane (OCM), and in particular membrane reactors, contribute toward reaching the yield required to make the process competitive at the industrial scale. Therefore, in this work, the conventional OCM packed bed reactor using a Mn-Na₂WO₄/SiO₂ catalyst was experimentally compared with a membrane reactor, in which a symmetric MgO porous membrane was integrated. The beneficial effects of distributive feeding of oxygen along the membrane, which is the main advantage of the porous membrane reactor, were demonstrated, although no significant differences in terms of performance were observed because of the adverse effects of back-permeation prevailing in the experiments. A sensitivity analysis carried out on the effective diffusion coefficient also indicated the necessity of properly tuning the membrane properties to achieve the expected promising results, highlighting how this tuning could be addressed.

Lower olefins from methane: recent advances

Modern methods for methane conversion to lower olefins having from 2 to 4 carbon atoms per molecule are generalized. Multistage processing of methane into ethylene and propylene via syngas or methyl chloride and methods for direct conversion of CH4 to ethylene are described. Direct conversion of syngas to olefins as well as indirect routes of the process via methanol or dimethyl ether are considered. Particular attention is paid to innovative methods of olefin synthesis. Recent achievements in the design of catalysts and development of new techniques for efficient implementation of oxidative coupling of methane and methanol conversion to olefins are analyzed and systematized. Advances in commercializing these processes are pointed out. Novel catalysts for Fischer – Tropsch synthesis of lower olefins from syngas and for innovative technique using oxide – zeolite hybrid catalytic systems are described. The promise of a new route to lower olefins by methane conversion via dimethyl ether is shown. Prospects for the synthesis of lower olefins via methyl chloride and using non-oxidative coupling of methane are discussed. The most efficient processes used for processing of methane to lower olefins are compared on the basis of degree of conversion of carbonaceous feed, possibility to integrate with available full-scale production, number of reaction stages and thermal load distribution.

The bibliography includes 346 references.