Superhydrophobic graphene-based sponge as a novel sorbent for crude oil removal under various environmental conditions

An immobilized composite microbial material combined with slow release agents enhances oil-contaminated groundwater remediation

Microbial remediation of oil-contaminated groundwater is often limited by the low temperature and lack of nutrients in the groundwater environment, resulting in low degradation efficiency and a short duration of effectiveness. In order to overcome this problem, an immobilized composite microbial material and two types of slow release agents (SRA) were creatively prepared. Three oil-degrading bacteria, Serratia marcescens X, Serratia sp. BZ-L I1 and Klebsiella pneumoniae M3, were isolated from oil-contaminated groundwater, enriched and compounded, after which the biodegradation rate of the Venezuelan crude oil and diesel in groundwater at 15 °C reached 63 % and 79 %, respectively. The composite microbial agent was immobilized on a mixed material of silver nitrate-modified zeolite and activated carbon with a mass ratio of 1:5, which achieved excellent oil adsorption and water permeability performance. The slow release processes of spherical and tablet SRAs (SSRA, TSRA) all fit well with the Korsmeyer-Peppas kinetic model, and the nitrogen release mechanism of SSRA N2 followed Fick's law of diffusion. The highest oil removal rates by the immobilized microbial material combined with SSRA N2 and oxygen SRA reached 94.9 % (sand column experiment) and 75.1 % (sand tank experiment) during the 45 days of remediation. Moreover, the addition of SRAs promoted the growth of oil-degrading bacteria based on microbial community analysis. This study demonstrates the effectiveness of using immobilized microbial material combined with SRAs to achieve a high efficiency and long-term microbial remediation of oil contaminated shallow groundwater.

3D Oleophilic Sorbent Films Based on Recycled Low-Density Polyethylene

Recycling low-end, one-time-use plastics-such as low-density polyethylene (LDPE)-is of paramount importance to combat plastic pollution and promote sustainability in the modern green economy. This study valorizes LDPE waste by transforming it into 3D oleophilic swellable thin films through a process involving dissolution, phase separation, and extraction. These films are subsequently layered using a customized polypropylene (PP) based nonwoven fabric separator and securely sealed in a zigzag pattern. The zigzag-shaped seal enhances the adhesion of pollutants to the sorbent by providing wire curvatures that increase retention time and uptake capacity. As a result, the sorbent exhibits impressive oil uptake capacities, with immediate and equilibrium values of 120 g/g and 85 g/g, respectively. Notably, the as-prepared sorbent demonstrates low water retention and high selectivity for oil, outperforming commercially available oil sorbents. The unique design involving a 3D-film structure, superposed films, and a zigzag-shaped seal offers a sustainable and value-added solution to the issues of LDPE waste and oil spills on water surfaces.

Oil Adsorption Kinetics of Calcium Stearate-Coated Kapok Fibers

This study used a simple and efficient dipping method to prepare oleophilic calcium stearate-coated kapok fibers (CaSt₂-KF) with improved hydrophobicity. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) confirmed the deposition of calcium stearate particles on the surface of the kapok fibers. This led to higher surface roughness and improved static water contact angle of 137.4°. The calcium stearate-coated kapok fibers exhibited comparable sorption capacities for kerosene, diesel, and palm oil. However, the highest sorption capacity of 59.69 g/g was observed for motor oil at static conditions. For motor oil in water, the coated fibers exhibited fast initial sorption and a 65% removal efficiency after 30 s. At equilibrium, CaSt₂-KF attained a sorption capacity of 33.9 g/g and 92.5% removal efficiency for motor oil in water. The sorption kinetics of pure motor oil and motor oil in water follows the pseudo-second-order kinetic model, and the Elovich model further described chemisorption. Intraparticle diffusion and liquid film diffusion were both present, with the latter being the predominant diffusion mechanism during motor oil sorption.

3D graphene-based adsorbents: Synthesis, proportional analysis and potential applications in oil elimination

The suitability and efficacy of three-dimensional (3D) graphene, including its derivatives, have garnered widespread attention towards the development of novel, sustainable materials with ecological amenability. This is especially relevant towards its utilization as adsorbents of wastewater contaminants, such as heavy metals, dyes, and oil, which could be majorly attributed to its noteworthy physicochemical features, particularly elevated chemical and mechanical robustness, advanced permeability, as well as large specific surface area. In this review, we emphasize on the adsorptive elimination of oil particles from contaminated water. Specifically, we assess and collate recent literature on the conceptualization and designing stages of 3D graphene-based adsorbents (3DGBAs) towards oil adsorption, including their applications in either batch or continuous modes. In addition, we analytically evaluate the adsorption mechanism, including sorption sites, physical properties, surface chemistry of 3DGBA and interactions between the adsorbent and adsorbate involving the adsorptive removal of oil, as well as numerous effects of adsorption conditions on the adsorption performance, i.e. pH, temperature, initial concentration of oil contaminants and adsorbent dosage. Furthermore, we focus on the equilibrium isotherms and kinetic studies, in order to comprehend the oil elimination procedures. Lastly, we designate encouraging avenues and recommendations for a perpetual research thrust, and outline the associated future prospects and perspectives.

Recent Developments and Advancements in Graphene-Based Technologies for Oil Spill Cleanup and Oil-Water Separation Processes

The vast demand for petroleum industry products led to the increased production of oily wastewaters and has led to many possible separation technologies. In addition to production-related oily wastewater, direct oil spills are associated with detrimental effects on the local ecosystems. Accordingly, this review paper aims to tackle the oil spill cleanup issue as well as water separation by providing a wide range of graphene-based technologies. These include graphene-based membranes; graphene sponges; graphene-decorated meshes; graphene hydrogels; graphene aerogels; graphene foam; and graphene-coated cotton. Sponges and aerogels modified by graphene and reduced graphene oxide demonstrated effective oil water separation owing to their superhydrophobic/superoleophilic properties. In addition, oil particles are intercepted while allowing water molecules to penetrate the graphene-oxide-coated metal meshes and membranes thanks to their superhydrophilic/underwater superoleophobic properties. Finally, we offer future perspectives on oil water separation that are hindering the advancements of such technologies and their large-scale applications.

Carrageenan-based nano-hybrid materials for the mitigation of hazardous environmental pollutants

Fast industrialization and population growth are associated with the increased release of hazardous contaminants in the environment. These hazardous substances, including pharmaceutical, biomedical, personal-care products, heavy metals, endocrine-disrupters, and colorants, pollute the ecosystem by disturbing nature's balance. Nanotechnology has paved new horizons in biochemical engineering by designing novel approaches of integrating nanoscale science with biotechnology to construct improved quality materials for target uptake of pollutants. Recently, nanostructured materials have emerged as research and development frontiers owing to their excellent properties. The tailored designing of nanohybrids constructs with physicochemical alteration enables the nano-bioadsorbent with high target specificity and efficiency. The development of eco-friendly, biodegradable, cost-efficient, and biopolymer-based nanohybrid constructs is gaining attention to remove hazardous environmental pollutants. κ-carrageenan biopolymer is frequently used with different nanomaterials to design nanohybrid bio-adsorbents to remove various contaminants. Herein, the potentialities of carrageenan-based nanohybrid constructs in environmental remediation have been summarized. Different nanostructures, e.g., silica, non-magnetic/magnetic, carbon nanotubes/nanorods, nanoclay/nanomembrane, metal organic frameworks, graphene oxide, and other nanomaterials have been described in combination with carrageenan biopolymers focusing on environmental remediation.

Effective multi-functional biosorbent derived from corn stalk pith for dyes and oils removal

In this study, malic acid-modified corn stalk pith (MA-CSP) was prepared as an environmentally friendly multi-functional bio-sorbent for adsorbing of dyes and oils. The sorption capacity of the MA-CSP for single and binary dyes is 328.46 mg/g - 566.27 mg/g. In addition, the MA-CSP also had good sorption for lubricating oil, soybean oil, diesel oil, and isopropyl alcohol, which were 37.2 g/g, 44.1 g/g, 33.8 g/g, and 29.3 g/g, respectively. Physical and statistical models were used to analyze the adsorption behavior of methylene blue (MB) and crystal violet (CV). And its sorption behavior for dyes was also affected by the co-existing salts in water. The sorption mechanism of the dye was mainly electrostatic attraction and hydrogen bonding action. The sorption of oil was primarily via the role of van der Waals force and hydrophobic interaction. The MA-CSP, as an eco-friendly, economical and efficient multi-functional sorbent, holds promise for effective dyes and oil removal from contaminated water, and its application in other fields is also highly anticipated.

Sorption as a rapidly response for oil spill accidents: A material and mechanistic approach

Accidents involving oil transportation has increase due to directly connection with the elevation of global energy demand. The environmental losses are tremendous and brings huge economic issues to remediate the spilled oil. This report presents an up-to-date review on an overall aspects of oil spill remediation techniques, the fundamentals and advantages of sorption, the most applied materials through diverse types of oil spill sites and oils with variety features, highlight to natural materials and future prospective. As the environment preservation progressively becomes a major social concern issue, the achievement of a worldwide distribution process aligned with environmental legislation and economic viability is crucial to the oil industry. For this, a specific preparation considering several scenarios must be carried out regarding minimization of oil spillages. Since the sorbent materials are decisive for sorption, it was approached the main sorbents: natural, graphenic, nano, polymeric and waste materials, and future trends.

Crude oil and S500 diesel removal from seawater by polyurethane composites reinforced with palm fiber residues

In this work, we prepared PU-composites with Australian palm residues (PR) in different contents (5, 10, 15, and 20 wt%) and granulometry (28 and 35 mesh) to improve the oil (crude oil and S500 Diesel) sorption capacity. The foams were characterized by life cycle assessment (LCA), scanning electron microscopy, oil sorption, desorption, and Langmuir, Freundlich, and Temkin sorption isotherms. LCA indicated that higher PR contents decreased the foam environmental impacts than the classical residue handling, indicating that 20 wt% PR is the better environmental option, independent of the residues granulometry. The PR incorporation into PU foams resulted in smaller pore sizes, with a higher number of homogeneous open-cells. The PU composites exhibited higher oil adsorption capacity than the pristine foam. The PU sample showed maximum absorption capability of 6.1 and 6.7 g g^-1 for diesel S500 and crude oil, and the composites showed increased values of ∼18 g g^-1 and ∼24 g g^-1. The Langmuir model presented the best fit and predicted a maximum adsorption capacity of 30.39 and 25.57 g g^-1 for PU-20% PR 28 and 35 mesh, respectively. The composites presented excellent reusability with PU-20% PR (28 mesh) and PU-20% PR (35 mesh), showing removal efficiency after 16 and 9 cycles, respectively. The results classify the developed foams as excellent materials to sorb spilled crude oil in marine accidents.

Fabrication of three bio-adsorbents from different parts of rape straw

Three kinds of bio-adsorbents are fabricated from the different parts of rape straw, which are adsorbent core, adsorbent hull, and adsorbent stalk, respectively. As the adsorbates, kerosene, paraffin, rapeseed oil, and dibutyl phthalate are employed to evaluate the adsorption performance of the three kinds of bio-adsorbents. The results suggest that adsorbent core has much higher adsorption quantity to all the four adsorbates (27.37, 32.23, 33.37, and 39.28 g/g, respectively) than adsorbent hull (7.39, 8.37, 8.85, and 10.30 g/g) and adsorbent stalk (6.75, 7.25, 7.92, and 9.32 g/g). The adsorption mechanism of the three bio-adsorbents is investigated. The results illustrate that different bio-adsorbents own different micromorphologies. The special microchamber structure is found in the bio-adsorbent of the adsorbent core, which is seen as the main reason for its excellent adsorption performance. The adsorption volume of unit mass (Va) was proposed to evaluate the intrinsic adsorption properties of the bio-adsorbents. The recovery performance of the bio-adsorbents is investigated by using of two different treatment methods. The effect of treatment on recovery rate is discussed.

Adsorptive removal of oil spill from sea water surface using magnetic wood sawdust as a novel nano-composite synthesized via microwave approach

Water pollution by oil is a serious environmental problem. Developing new generation of benign adsorbents satisfying several criteria required for real practical application is of great need. This work introduces an effort in this direction, by utilizing a facile synthesis of wood sawdust coated magnetite nanoparticles functionalized stearic acid (WSD@Fe₃O₄NPs/SA) as a novel nano composite along with its precursor WSD@Fe₃O₄NPs. SA was covalently bonded to the precursor by amide bond formation via the interaction with the silylating agent 3-aminopropyltrimethoxysilane (3-APTS). This mode of binding is more stronger than the conventional ester bond. Fourier transform infrared (FT-IR), X- ray powder diffraction (XRD), Scanning electron microscope (SEM) and Transmittance electron microscope (TEM) were employed for characterization and follow up the synthesis process. Application of the newly synthesized magnetic nano composite adsorbent under optimized parameters of contact time (min) and composite dosage (g) reveal high removal capacity values (g/g) evaluated to be 28.32 g/g, 5 min and 0.1 g for used motor oil removal and 41.22 g/g, 10 min and 0.1 g for crude oil. The high removal efficiency exhibited by WSD@Fe₃O₄NPs/SA was mainly argued to the long hydrocarbon chain of SA moiety and additional ـــ (CH₂)₃ ـــ groups incorporated 3-ATPS. Moreover, Analysis of the oil adsorption experimental equilibrium data were well fitted with Freundlish model with correlation coefficients r² = 0.9788 and 0.9896 for used motor oil and crude oil, respectively. The kinetic data were correlated using two kinetic models and the results were in harmony with pseudo-second order.

Naturally pre-designed biomaterials: Spider molting cuticle as a functional crude oil sorbent

Diverse fields of modern environmental technology are nowadays focused on the discovery and development of new sources for oil spill removal. An especially interesting type of sorbents is those of natural origin-biosorbents-as ready-to-use constructs with biodegradable, nontoxic, renewable and cost-efficient properties. Moreover, the growing problem of microplastic-related contamination in the oceans further encourages the use of biosorbents. Here, for the first time, naturally pre-designed molting cuticles of the Theraphosidae spider Avicularia sp. "Peru purple", as part of constituting a large-scale spider origin waste material, were used for efficient sorption of crude oil. Compared with currently used materials, the proposed biosorbent of spider cuticular origin demonstrates excellent ability to remain on the water surface for a long time. In this study the morphology and hydrophobic features of Theraphosidae cuticle are investigated for the first time. The unique surface morphology and very low surface free energy (4.47 ± 0.08 mN/m) give the cuticle-based, tube-like, porous biosorbent excellent oleophilic-hydrophobic properties. The crude oil sorption capacities of A. sp. "Peru purple" molt structures in sea water, distilled water and fresh water were measured at 12.6 g/g, 15.8 g/g and 16.6 g/g respectively. These results indicate that this biomaterial is more efficient than such currently used fibrous sorbents as human hairs or chicken feathers. Four cycles of desorption were performed and confirmed the reusability of the proposed biosorbent. We suggest that the oil adsorption mechanism is related to the brush-like and microporous structure of the tubular spider molting cuticles and may also involve interaction between the cuticular wax layers and crude oil.

Research Progress and Prospects of Marine Oily Wastewater Treatment: A Review

Oily wastewater from shipping waste and marine accidents have seriously polluted the marine environment and brought great harm to human production and health. With the increasing awareness of environmental protection, the treatment of marine oily wastewater has attracted extensive attention from the international community. Marine oily wastewater has various forms and complex components, so its treatment technology faces great challenges. Sources, types, supervision, and treatment of marine oily wastewater are introduced in this paper. The research progress of marine and ship’s oily wastewater treatment technologies in recent years are reviewed from the perspectives of physical treatment, chemical treatment, biological treatment, and combined treatment, respectively. Principles and characteristics of all kinds of technologies were analyzed. In addition, this paper shows that multiple processing technologies used in combination for the purpose of high efficiency, environmental protection, economy, and energy conservation are the future development trend.

Robust, Lightweight, Hydrophobic, and Fire-Retarded Polyimide/MXene Aerogels for Effective Oil/Water Separation

Polyimide (PI) aerogels have attracted great attention owing to their low density and excellent thermal stability. However, hydrophobic surface modification is required for PI aerogels to improve their ability in oil/water separation due to their amphiphilic characteristic. Two-dimensional MXenes (transition metal carbides/nitrides) can be utilized as nanofillers to enhance the properties of polymers because of their unique layered structure and versatile interface chemistry. Herein, the robust, lightweight, and hydrophobic PI/MXene three-dimensional architectures were fabricated via freeze-drying of polyamide acid/MXene suspensions and thermal imidization. Polyamide acid was synthesized using N-N-dimethylacetamide and 4,4'-oxydianiline. MXene (Ti₃C₂T_x) dispersion was obtained via the etching of Ti₃AlC₂ and ultrasonic exfoliation. Taking advantage of the strong interaction between PI chains and MXene nanosheets, the interconnected, highly porous, and hydrophobic PI/MXene aerogels with low density were fabricated, resulting in the improved compressive performance, remarkable oil absorption capacity, and efficient separation of oil and water. For the PI/MXene-3 aerogel (weight ratio, 5.2:1) without any surface modification, the water contact angle was 119° with a density of 23 mg/cm³. This aerogel can completely recover to its original height after 50 compression-release cycles, exhibiting superelasticity and exceptional fatigue-resistant ability. It also showed high absorption capacities to various organic liquids ranging from approximately 18 to 58 times of their own weight. This hybrid aerogel can rapidly separate the chloroform, soybean oil, and liquid paraffin from the water-oil system. The thermally stable hybrid aerogel also exhibited excellent fire safety properties and outstanding reusability under an extreme environment.

Natural rubber/reduced-graphene oxide composite materials: Morphological and oil adsorption properties for treatment of oil spills

•

Natural rubber/rGO composite foam was used as an oil sorbent.

•

Addition of rGO enhanced the oil adsorption capacity and strength of NR sorbent foam.

•

Inclusion of 0.5 phr rGO into NR increased the crude oil adsorption capacity to 17.04 g g⁻¹.

•

Oil adsorption mechanism of the sorbent materials was proposed.

•

Reusability of the NR/rGO sorbent was greater than 70% oil adsorption for 30 cycles.

A green sorbent material was fabricated through the simple addition of reduced graphene oxide (rGO) to natural rubber (NR) latex. The effect of rGO content in the NR foam on petroleum oil adsorption was investigated. The addition of rGO in NR increased the petroleum oil adsorption capacity of the resulting NR/rGO (NRG) composite foam (12–21 g g⁻¹) with respect to those of the pure NR foam (8–15 g g⁻¹) and a commercial sorbent (6–7 g g⁻¹). The adsorption capacity was optimal for 0.5 phr rGO (NRG-0.5). Further, the environmental conditions (temperature and waves) affected the oil adsorption capacity of the sorbent materials. The adsorption kinetics of the sorbent materials for crude AXL oil was best described with pseudo-second-order kinetics. The interparticle diffusion model revealed three steps whereas the adsorption isotherms approximated the Langmuir isotherms. Moreover, the oil adsorption mechanisms of the NR and NRG sorbent materials were compared to that of a commercial sorbent. The high elasticity of the NRG-0.5 composite foam improved not only the oil adsorption capacity but also the reusability of the sorbent material. The presence of rGO increased the strength of the NRG-0.5 compared to that of pure NR, which resulted in a high-performance and reusable material with an oil removal efficiency higher than 70% after 30 uses.

Burning rate, flame geometry and temperature of convection-controlled circular diesel oil pool fire under air crossflow conditions

Hazardous fires in fuel storage tanks may result in casualties of great impact. Efforts are being done to master the physics of the phenomena, aiming both avoidance and damage minimization. Flame characterization is an important approach studied by many researchers. This article presents the results of an experimental investigation of diesel oil (S500 type) pool fires under air crossflow conditions. A reduced scale model properly instrumented was tested in an aerodynamic channel. Measurement techniques include analysis of infrared images of pool fires, mass burning rates and flame geometry as a function of air crossflow velocity (which ranged from 0 m/s - quiescent air - to 4.0 m/s). Mass burning rates showed an oscillatory behavior as the crossflow velocity was raised. Regarding flame geometry, for an increasing air crossflow, firstly flame tilt angle increased, flame length decreased and flame height decreased until about 1.5-2.0 m/s, while after that velocity, flame geometry became nearly steady. Geometry results were also compared with thirteen correlations from literature for geometric parameters obtaining good agreement for some of them. The IR-measured temperatures showed that the flame region (reacting region) became hotter and the plume region (non-reacting region) became colder as the air crossflow velocity was increased.

Mechanochemically Synthesised Coal-Based Magnetic Carbon Composites for Removing As(V) and Cd(II) from Aqueous Solutions

The continued decrease in water quality requires new advances in the treatment of wastewater, including the preparation of novel, effective, environmentally friendly, and affordable sorbents of toxic pollutants. We introduce a simple non-conventional mechanochemical synthesis of magnetically responsive materials. Magnetic lignite and magnetic char were prepared by high-energy ball co-milling from either raw Slovak lignite or coal-based char together with a ferrofluid. The products were characterised by X-ray diffraction, electron microscopy, ⁵⁷Fe Mössbauer spectroscopy, X-ray photoelectron spectroscopy (XPS), volumetric magnetic susceptibility, and low-temperature nitrogen adsorption, and both magnetic carbons were comparatively tested as potential sorbents of As(V) oxyanions and Cd(II) cations in aqueous solutions. The magnetic char was an excellent sorbent of As(V) oxyanions (Q_m = 19.9 mg/g at pH 3.9), whereas the magnetic lignite was less effective. The different sorption properties towards arsenic anions may have been due to different oxidation states of iron on the surfaces of the two magnetic composites (determined by XPS), although the overall state of iron monitored by Mössbauer spectroscopy was similar for both samples. Both magnetic composites were effective sorbents for removing Cd(II) cations (Q_m (magnetic lignite) = 70.4 mg/g at pH 6.5; Q_m (magnetic char) = 58.8 mg/g at pH 6.8).