Selective adsorption of phenanthrene dissolved in Tween 80 solution using activated carbon derived from walnut shells

Sustainable application of surfactants in soil remediation: Selective pollutants adsorption and hydrogen peroxide-driven adsorbent regeneration

The uncontrolled disposal of the liquid lindane wastes have led to the formation of dense non-aqueous phase liquids (DNAPL), consisting of 28 chlorinated organic compounds (COCs), contaminating soil and groundwater. Surfactant-enhanced aquifer remediation is proposed as technology to treat these sites. However, the polluted emulsion generated must be manged on-site. In this work a two-step process is applied to treat emulsion composed of E-Mulse® 3 (4 g·L-1) as surfactant and a DNAPL (2 gCOCs·L-1). In the first, the COCs were selectively adsorbed in a granular activated carbon (GAC) column with Fe (II) previously adsorbed (10-20mg·g-1) onto the carbon surface, recovering an aqueous phase with surfactant for their reuse. In the second step, the spent GAC was regenerated with a 40 g·L-1 solution of hydrogen peroxide fed to the column at 2 mL·min-1 to promote the oxidation of the COCs adsorbed in the GAC. The kinetic and adsorption model in a multisolute (surfactant and DNAPL) system has been proposed. Five successive cycles of regeneration/adsorption have been successfully applied in the column process. About 50 % of the COCs were retained from the emulsion, and more than 70 % of the surfactant was recovered. The consumption of unproductive oxidants decreased with the number of regeneration cycles. The water effluent obtained after regeneration of GAC did not present chlorinated compounds desorbed and nontoxic by-products generated, such as short-chain acids.

Reuse of polymeric waste for the treatment of marine water polluted by diesel

Accidental diesel spills can occur in marine environments such as harbors, leading to adverse effects on the environmental compartment and humans. This study proposes the surgical mask as an affordable and sustainable adsorbent for the remediation of diesel-contaminated seawater to cope with the polymeric waste generated monthly in hospital facilities. This approach can also be helpful considering a possible future pandemic, alleviating the pressure on the waste management system by avoiding improper mask incineration and landfilling, as instead occurred during the previous COVID-19. Batch adsorption-desorption experiments revealed a complete diesel removal from seawater after 120 min with the intact laceless mask, which showed an adsorption capacity of up to 3.43 g/g. The adsorption curve was better predicted via Weber and Morris's kinetic (R2 = 0.876) and, in general, with Temkin isotherm (R2 = 0.965-0.996) probably due to the occurrence of chemisorption with intraparticle diffusion as one of the rates-determining steps. A hysteresis index of 0.23-0.36 was obtained from the desorption isotherms, suggesting that diesel adsorption onto surgical masks was faster than the desorption mechanism. Also, the effect of pH, ionic strength and temperature on diesel adsorption was examined. The results from the reusability tests indicated that the surgical mask can be regenerated for 5 consecutive cycles while decreasing the adsorption capacity by only approximately 11%.

Efficient removal of polybrominated diphenyl ethers from soil washing effluent by dummy molecular imprinted adsorbents: Selectivity and mechanisms

Surfactant enhanced elution is an effective method for removing hydrophobic organic pollutants from soils. The key to the development of leaching technology is selective removal of targeted pollutants in soil washing effluent and recycling of surfactant solutions. In this study, a molecular imprinting technique was applied to selectively sorb polybrominated diphenyl ethers (PBDEs) in soil washing effluent. The novel molecular imprinted polymers (MIPs) using different template molecules were synthesized by precipitation polymerization. Adsorption behaviors and mechanisms of MIPs were studied through experiments and theoretical calculations. The results show that 4-bromo-4'-hydroxybiphenyl and toluene can be effective imprinting molecule for MIPs synthesis. The maximal adsorption capacity of selected dummy molecular imprinted polymer (D₁-MIP) was 1032.36 µmol/g, and that of part molecular imprinted polymer (P-MIP) was 981.13 µmol/g. Their imprinting factors in 5 PBDEs adsorption ranged from 2.13 to 5.88, the recovery percentage of Triton X-100 can reach 99.09%, confirming the feasibility of reusing surfactant. Various PBDEs could be removed by MIPs, and Quantitative Structure Property Relationship analysis revealed that PBDEs' molecular volume, planarity, polarity, and hydrophobicity have major influences on their adsorption performance. DFT calculation revealed that Van der Waals force and hydrogen bonding played important roles during selective adsorption. These results can provide effective theoretical guidance for surfactant enhanced soil elution in practical engineering applications.

Adsorption of Phenanthrene on Multi-Walled Carbon Nanotubes in the Presence of Nonionic Surfactants

The bioavailability and mobility of phenanthrene (Phe) adsorbed by multi-walled carbon nanotubes (MWCNTs) may be substantially influenced by nonionic surfactants used both in the synthesis and dispersion of MWCNTs. The adsorption mechanisms of Phe adsorbed onto MWCNTs under the different nonionic surfactants Tween 80 (TW-80) and Triton X-100 (TX-100) in the aqueous phase were investigated in terms of changes in the MWCNTs' compositions and structures. The results showed that TW-80 and TX-100 were easily adsorbed onto MWCNTs. Phe adsorption data onto MWCNTs were better suited to the Langmuir equation than the Freundlich equation. Both TW-80 and TX-100 reduced the adsorption capacity of Phe onto MWCNTs. When TW-80 and TX-100 were added in the adsorption system, the saturated adsorption mass of Phe decreased from 35.97 mg/g to 27.10 and 29.79 mg/g, respectively, which can be attributed to the following three reasons. Firstly, the hydrophobic interactions between MWCNTs and Phe became weakened in the presence of nonionic surfactants. Secondly, the nonionic surfactants covered the adsorption sites of MWCNTs, which caused Phe adsorption to be reduced. Finally, nonionic surfactants can also promote the desorption of Phe from MWCNTs.

Surfactant recovery and efficient separation of PAHs from surfactant solutions by low-cost waste activated sludge and two-stage design optimization

The treatment and surfactant recovery of soil washing/flushing effluent containing high levels of surfactants and organic pollutants are critical for the surfactant-assisted remediation of soils and waste management due to their complexity and high-potential risks. Combination of waste activated sludge material (WASM) and a kinetic-based two-stage system design was introduced in this study as a novel strategy for the separation of phenanthrene and pyrene from Tween 80 solutions. The results showed that WASM can effectively sorb phenanthrene and pyrene with high affinities (K_d) of 2325.5 L·kg^-1 and 9911.2 L·kg^-1, respectively. This allowed a high-level recovery of Tween 80 of 90.47 ± 1.86%, with selectivity of up to 69.7. In addition, a two-stage design was constructed, and the results showed an improved reaction time (approximately 5% of equilibrium time in conventional single-stage process) and increased the separation levels of phenanthrene or pyrene from Tween 80 solutions. For instance, the minimal total operating time for the sorption of 99% pyrene from 1.0 g·L^-1 Tween 80 was only 23.0 min in the two-stage process compared to that of 480 min with a 71.9% removal level in the single-stage system. Results indicated that the combination of low-cost waste WASH and two-stage design was a high-efficiency and time-saving way to recover surfactants from soil washing effluents.

Adsorption and Removal of Antibiotic Pollutants using CuO-Co3 O4 Co-modified Porous Boron Nitride Fibers in Aqueous Solution

The presence of antibiotic contaminants in aqueous environment already poses significant risks to ecological sustainability, biodiversity and human public health and safety. Therefore, it is urgent to develop practical water pollution control technologies and new materials. Here, we prepared CuO-Co₃ O₄ co-modified porous boron nitride fibers (P-BNFs) for the adsorption and removal of tetracycline antibiotics (TCs) in aqueous environment. The prepared adsorbents were characterized by XRD, FTIR, XPS, SEM, TEM and BET, and the adsorption behavior was explored by batch experiments. The results show that the removal percentage for doxycycline (DC) reaches 98.68 %, which was much higher than that of P-BNFs, and the modification results of P-BNFs with CuO or Co₃ O₄ alone. After five regeneration cycles, the removal rate of DC by CuO-Co₃ O₄ /P-BNFs was still as high as 89.33 %. This is promising and indicates that the prepared CuO-Co₃ O₄ /P-BNFs adsorbent has good renewable recycling performance and practical application prospects.

Review on carbon-based adsorbents from organic feedstocks for removal of organic contaminants from oil and gas industry process water: Production, adsorption performance and research gaps

Large amounts of process water with considerable concentrations of recalcitrant organic contaminants, such as polycyclic aromatic hydrocarbon (PAHs), phenolic compounds (PCs), and benzene, toluene, ethylbenzene, and xylene (BTEX), are generated by several segments of oil and gas industries. These segments include refineries, hydraulic fracturing (HF), and produced waters from the extraction of shale gas (SGPW), coalbed methane (CBMPW) and oil sands (OSPW). In fact, the concentration of PCs and PAHs in process water from refinery can reach 855 and 742 mg L^-1, respectively. SGPW can contain BTEX at concentrations as high as 778 mg L^-1. Adsorption can effectively target those organic compounds for the remediation of the process water by applying carbon-based adsorbents generated from organic feedstocks. Such organic feedstocks usually come from organic waste materials that would otherwise be conventionally disposed of. The objective of this review paper is to cover the scientific progress in the studies of carbon-based adsorbents from organic feedstocks that were successfully applied for the removal of organic contaminants PAHs, PCs, and BTEX. The contributions of this review paper include the important aspects of (i) production and characterization of carbon-based adsorbents to enhance the efficiency of organic contaminant adsorption, (ii) adsorption properties and mechanisms associated with the engineered adsorbent and expected for certain pollutants, and (iii) research gaps in the field, which could be a guidance for future studies. In terms of production and characterization of materials, standalone pyrolysis or hybrid procedures (pyrolysis associated with chemical activation methods) are the most applied techniques, yielding high surface area and other surface properties that are crucial to the adsorption of organic contaminants. The adsorption of organic compounds on carbonaceous materials performed well at wide range of pH and temperatures and this is desirable considering the pH of process waters. The mechanisms are frequently pore filling, hydrogen bonding, π-π, hydrophobic and electrostatic interactions, and same precursor material can present more than one adsorption mechanism, which can be beneficial to target more than one organic contaminant. Research gaps include the evaluation of engineered adsorbents in terms of competitive adsorption, application of adsorbents in oil and gas industry process water, adsorbent regeneration and reuse studies, and pilot or full-scale applications.

Treatment of PBDEs from Soil-Washing Effluent by Granular-Activated Carbon: Adsorption Behavior, Influencing Factors and Density Functional Theory Calculation

Soil-washing is a potential technology for the disposal of soil contaminated by e-waste; however, the produced soil-washing effluent will contain polybrominated diphenyl ethers (PBDEs) and a large number of surfactants, which are harmful to the environment, so the treatment of PBDEs and the recycling of surfactants are the key to the application of soil-washing technology. In this study, coconut shell granular-activated carbon (GAC) was applied to remove PBDEs from Triton X-100 (TX-100) surfactant which simulates soil-washing effluent. The adsorption results show that, GAC can simultaneously achieve effective removal of 4,4′-dibromodiphenyl ether (BDE-15) and efficient recovery of TX-100. Under optimal conditions, the maximum adsorption capacity of BDE-15 could reach 623.19 μmol/g, and the recovery rate of TX-100 was always higher than 83%. The adsorption process of 4,4′-dibromodiphenyl ether (BDE-15) by GAC could best be described using the pseudo-second-order kinetic model and Freundlich isothermal adsorption model. The coexistence ions had almost no effect on the removal of BDE-15 and the recovery rate of TX-100, and the solution pH had little effect on the recovery rate of TX-100; BDE-15 had the best removal effect under the condition of weak acid to weak base, indicating that GAC has good environmental adaptability. After adsorption, GAC could be regenerated with methanol and the adsorption effect of BDE-15 could still reach more than 81%. Density functional theory (DFT) calculation and characterization results showed that, Van der Waals interaction and π–π interaction are dominant between BDE-15 and GAC, and hydrogen bond interactions also exist. The existence of oxygen-containing functional groups is conducive to the adsorption of BDE-15, and the carboxyl group (-COOH) has the strongest promoting effect. The study proved the feasibility of GAC to effectively remove PBDEs and recover surfactants from the soil-washing effluent, and revealed the interaction mechanism between PBDEs and GAC, which can provide reference for the application of soil-washing technology.

Coupling of desorption of phenanthrene from marine sediments and biodegradation of the sediment washing solution in a novel biochar immobilized-cell reactor

The recurrent dredging of marine sediments needs the use of ex-situ technologies such as sediment washing (SW) to effectively remove polycyclic aromatic hydrocarbons. Notwithstanding, the large volumes of generated spent SW effluents require adequate treatment by employing highly-efficient, inexpensive and environmentally-friendly solutions. This study proposes the phenanthrene (PHE) desorption from sediments using Tween® 80 (TW80) as extracting agent and the treatment of the resulting spent SW solution in a biochar (BC) immobilized-cell bioreactor. The SW process reached the highest PHE removal of about 91% using a surfactant solution containing 10,800 mg L^-1 of TW80. The generated amount of spent PHE-polluted SW solution can be controlled by keeping a solid to liquid ratio of 1:4. A PHE degradation of up to 96% was subsequently achieved after 43 days of continuous reactor operation, aerobically treating the TW80 solution in the BC immobilized-cell bioreactor with a hydraulic retention time of 3.5 days. Brevundimonas, Chryseobacterium, Dysgonomonas, Nubsella, and both uncultured Weeksellaceae and Xanthobacteraceae genera were mainly involved in PHE biodegradation. A rough economic study showed a total cost of 342.60 € ton^-1 of sediment, including the SW operations, TW80 and BC supply and the biological treatment of the SW solution.

Influence of carbon-containing and mineral sorbents on the toxicity of soil contaminated with benzo[a]pyrene during phytotesting

Benzo[a]pyrene (BaP) is a member of polycyclic aromatic hydrocarbons known for high persistency and toxicity. Technologies of BaP sorption through solid matrixes have received relatively more attention. The present study was devoted to the phytotesting investigations of two different groups of sorbents, such as carbonaceous, including biochar and granulated activated carbon (GAC), and mineral, including tripoli and diatomite. Evaluation of the BaP removing efficiency was carried out using the phytotesting method with spring barley in Haplic Chernozem contaminated with different levels of contamination (200 and 400 μg kg^-1 BaP). The sorbents' efficiency for BaP remediation was estimated in the sorbents doses from 0.5 to 2.5% per kg of soil. It was shown that biochar and GAC decreased the soil toxicity class to a greater extent than mineral sorbents ones. The effect intensified with an increase in applying sorbents doses. The optimal dose of carbonaceous sorbents into the soil contaminated with 200 µg kg^-1 was 1%, decreasing the BaP content up 57-59% in the soil. Simultaneously, the optimal dose of the mineral sorbents was found to be 1.5%, which decreased the BaP content in the soil up 41-48%. Increasing the BaP contamination level up to 400 µg kg^-1 showed the necessity of a sorbent dose increasing. In these conditions, among all applied sorbents, only 2% GAC could reduce the soil toxicity class to the normal level up to 0.91-1.10. It was shown that BaP tended to migrate from the soil to the roots and further into the vegetative part of barley.

Selective sorption of PAHs from TX100 solution by resin SP850: effects of TX100 concentrations and PAHs solubility

Recycling of washing effluent by selective sorption using resins is a feasible method to lower the operation costs of surfactant enhanced remediation (SER). In this study, correlations capable of predicting the selective sorption removal of polycyclic aromatic hydrocarbons (PAHs) by resin SP850 from TX100 solution to recycle washing effluent in SER were developed. A negative relationship of sorption coefficients (log K _f) of PAHs by resin SP850 with TX100 initial concentrations (log C _0,TX100) and water solubilities (log S _w) of PAHs was observed, which indicated that solubility enhancement of PAHs in TX100 micelles was responsible for the decreasing of the selective sorption. Freundlich exponential coefficients (1/n) of PAHs were relatively constant (0.775 ± 0.012), suggesting that the sorption of PAHs by SP850 in the presence of surfactant is a surface adsorption process. The modified selectivity parameter (S*), having a relationship with log C _0,TX100 and PAHs log S _w as well, could be employed to evaluate the efficiency of the selective sorption process and select the optimal TX100 concentration in washing effluents. For example, at the given SP850 dose of 1.0 g L^-1, the optimal TX100 concentrations (C _opTX100) for naphthalene, acenaphthene, phenanthrene, pyrene, anthracene and benzanthracene were about 4200, 7100, 8000, 10 000, 18 000 and 19 500 mg L^-1, respectively, having a negative relationship with their log S _w. Moreover, the C _opTX100 was independent of the solid-to-solution ratio of SP850 and TX100 solution containing PAHs. These correlations would be helpful for the application of SER in contaminated soils by giving a method to quantitatively predict the selective sorption behaviors of PAHs by SP850 from TX100 solution, especially for the C _opTX100, using the S _w of organic compounds and surfactant concentrations.

Remediation of soils contaminated by hydrophobic organic compounds: How to recover extracting agents from soil washing solutions?

A lot of soil (particularly, former industrial and military sites) has been contaminated by various highly toxic contaminants such as petroleum hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), polychlorobiphenyls (PCBs) or chlorinated solvents. Soil remediation is now required for their promotion into new industrial or real estate activities. Therefore, the soil washing (SW) process enhanced by the use of extracting agents (EAs) such as surfactants or cyclodextrins (CDs) has been developed for the removal of hydrophobic organic compounds (HOCs) from contaminated soils. The use of extracting agents allows improving the transfer of HOCs from the soil-sorbed fraction to the washing solution. However, using large amount of extracting agents is also a critical drawback for cost-effectiveness of the SW process. The aim of this review is to examine how extracting agents might be recovered from SW solutions for reuse. Various separation processes are able to recover large amounts of extracting agents according to the physicochemical characteristics of target pollutants and extracting agents. However, an additional treatment step is required for the degradation of recovered pollutants. SW solutions may also undergo degradation processes such as advanced oxidation processes (AOPs) with in situ production of oxidants. Partial recovery of extracting agents can be achieved according to operating conditions and reaction kinetics between organic compounds and oxidant species. The suitability of each process is discussed according to the various physicochemical characteristics of SW solutions. A particular attention is paid to the anodic oxidation process, which allows either a selective degradation of the target pollutants or a complete removal of the organic load depending on the operating conditions.

Remediation of Cu-phenanthrene co-contaminated soil by soil washing and subsequent photoelectrochemical process in presence of persulfate

A promising technology was proposed for the remediation of Cu and phenanthrene (PHE) co-contaminated soil. Firstly, Cu and PHE were simultaneously removed from soil using an extraction agent containing ethylenediaminetetraacetic acid (EDTA) and Tween 80 (TW80). Specifically, Cu was mobilized by the chelation of EDTA while PHE was desorpted from soil by TW80 micelles. At 20 mL g^-1 of liquid to soil ratio, 10 g L^-1 TW80 and 1 mM EDTA, 73.5% Cu and 68.1% PHE were removed by soil washing. The extraction agent was then recovered from effluent by photoelectro-persulfate (PE/PS) process after soil washing. Under the conditions of 10 mM PS, 4 mA cm^-2 current density, natural pH of 3.5 and 150 min treatment, 83.6% Cu was reduced to elemental copper but only 36.8% EDTA was recovered, while 99.6% PHE was eliminated and 94.0% TW80 was recovered. The result of quenching experiments indicated PHE was predominantly oxidized by sulfate radical, though hydroxyl radical and singlet oxygen were also identified by electron paramagnetic resonance technique. The recovered extracting agent could be reused for further three washing cycles. The results demonstrated that soil washing followed by PE/PS process could be a cost-effective remediation technology for heavy metal and organic co-contaminated soil.

Study on the preparation of the hierarchical porous CX-TiO2 composites and their selective degradation of PHE solubilized in soil washing eluent

A series of CX-TiO₂(Carbon Xerogel- TiO₂) composites with a hierarchical porous structure were obtained through the sol-gel method followed by drying and carbonization, and have been applied to treating solubilizing wastewater containing a high concentration of phenanthrene (PHE). The characterizations demonstrated that the CX-TiO₂ exhibits a hierarchical porous structure, with particles of carbon and P25 being uniformly in the matrix. Removal efficiency of CX-TiO₂ on PHE in soil washing eluent (SWE) were evaluated under ultraviolet (UV) irradiation or dark condition, and P25 was employed as the reference. The results revealed that CX-TiO₂(0.2) had the best removal effect on PHE, with the efficiency as high as 97.8% under UV illumination within 15 h. It demonstrated that in the process of PHE removal by CX-TiO₂ whether it was under UV illumination or not, the adsorption plays a dominant role in the early stage. The kinetic behavior of PHE adsorption was fitted using the pseudo-first-order and pseudo-second-order, and Langmuir model and Freundlich models were applied to describe the PHE adsorption isotherms. The results indicating that it was a chemical adsorption process, which was influenced by the interaction between PHE and CX-TiO₂, and PHE is adsorbed on the interface of CX-TiO₂(0.2) in a single layer form, instead of agglomerating in the admicelle. A possible mechanism of removal of solubilized PHE in SWE was speculated, in which both hierarchical porous structure and appropriate micropores size of CX-TiO₂ were indispensable to the selective adsorption and degradation of PHE. Recycling performance certificated that the selective removal efficiency of PHE could still reach 82.09% after five recycles. Thus the excellent performance testified that the CX-TiO₂ have great potential in treating SWE containing solubilized PAHs.

Adsorption of phenanthrene from aqueous solutions by biochar derived from an ammoniation-hydrothermal method

An innovative ammoniation-hydrothermal method of biochar production was developed for the adsorption of phenanthrene (PHE) from aqueous solutions in this paper. Phragmites australis (PA) was used to produce biochar in a hydrothermal kettle at 280 °C in muffle furnace using urea as an ammoniation reagent. Characterizations were executed by scanning electron microscope (SEM), N₂ adsorption/desorption isotherms, X-ray diffraction (XRD), elemental analysis, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FT-IR) to explore its morphological, physical, and chemical properties. Batch experiments of PHE adsorption were carried out to study the adsorption isotherms and kinetics. Quantum chemistry computational simulations were employed based on density functional theory (DFT) to establish and optimize adsorption configurations and analyze the biochar's structural effects on adsorption performance. Results showed that the ammoniation-hydrothermal method produced biochar with a higher surface area and a maximum equilibrium adsorption capacity of 1.97 mg/g. The adsorption fitted well with Freundlich isotherm model (R² > 0.96) and Pseudo-second-order kinetic model (R² > 0.82). Adsorption energy calculation revealed that the N functionalities, especially pyridine N in the N-doped biochar structure, exhibited stronger binding ability with PHE, which contributed most to the favorable adsorption ability of the ammoniation-hydrothermal biochar.

Competitive adsorption of naphthalene and phenanthrene on walnut shell based activated carbon and the verification via theoretical calculation

Walnut shell based activated carbon (WAC) was prepared via microwave-assisted KOH activation.

Wood-based biochar as an excellent activator of peroxydisulfate for Acid Orange 7 decolorization

Wood-based biochar, as a metal-free heterogeneous activator of peroxydisulfate (PDS), was successfully prepared by pyrolysis of polar sawdust for efficient removal of Acid Orange 7 (AO7). The results demonstrate PDS could be effectively activated by wood-based biochar, and AO7 was rapidly eliminated in a wide range of pH value (3.0-10.0) with AO7 removal achieved ≥ 99.3% after 14 min reaction. The dominant reactive species in the biochar/PDS system were verified via radical quenching tests and electron paramagnetic resonance (EPR) technique. It is speculated that sulfate radicals (SO₄^•-) and hydroxyl radicals (^•OH) were formed on the surface of biochar. Based on the results of X-ray photoelectron spectroscopy (XPS), π-electron density and oxygen-containing functional groups (especially C-OH) on biochar surface were active centers for the catalytic reaction. Recycle experiments of biochar for 4 runs were carried out and the regeneration method of the catalyst was also studied.