Recycling supercapacitor activated carbons for adsorption of silver (I) and chromium (VI) ions from aqueous solutions

Influence of the iron-oxide mass fractions of magnetic powdered activated carbon on its hexavalent chromium adsorption performance in water

Magnetic powdered activated carbon (Mag-PAC) is an effective adsorbent to remove hexavalent chromium (Cr(VI)) from water and can be recovered for reuse. However, the tradeoff between the adsorption performance of Cr(VI) and magnetic properties of Mag-PAC remains unclear. Herein, we prepared a series of Mag-PAC adsorbents containing various iron-oxide mass fractions with FeSO4·7H2O as the precursor, using a facile wet-chemical precipitation route and conducted batch experiments to evaluate the Cr(VI) adsorption performance. Results revealed that Mag-PAC was functionalized by magnetic iron oxide comprising crystalline goethite and magnetite structures. Furthermore, its adsorption performance was highly dependent on pH and was most effective at an initial solution pH of 2. Both the sorption rate constant and Cr(VI) adsorption capacity were greatly influenced by magnetization, and they gradually decreased as the iron-oxide mass fraction increased. Among the prepared adsorbents, Mag-PAC-75 (∼32% wt iron) exhibited not only an excellent Cr(VI) adsorption performance (Langmuir adsorption capacity: 75.76 mg/g) but also effective magnetic properties (saturation magnetization: 9.66 emu/g). Coexisting anions had a negligible competitive effect on Cr(VI) removal by Mag-PAC-75 at an initial pH of 2, whereas the presence of tannic acid markedly improved the Cr(VI) elimination. The presence of trivalent chromium on the surface of Mag-PAC-75 confirmed via X-ray photoelectron spectroscopy indicated that some synergistic redox reactions may occur during the sorption process. After five regeneration cycles using NaOH, Mag-PAC-75 continued to exhibit a high Cr(VI) removal efficiency and magnetic stability. These findings indicate that optimizing the adsorption performance and magnetic properties is a key factor for realizing the practical application of Mag-PAC for Cr(VI) removal. Overall, Mag-PAC may have been a promising application prospect for Cr(VI) removal from water due to its high adsorption capacity and magnetic properties, coupled with its good reusability and magnetic stability after regeneration cycles.

Highly Selective Recovery of Gold by In Situ Magnetic Field-Assisted Fe/Co-MOF@PDA/NdFeB Double Network Gel

There are enormous economic benefits to conveniently increasing the selective recovery capacity of gold. Fe/Co-MOF@PDA/NdFeB double-network organogel (Fe/Co-MOF@PDA NH) is synthesized by aggregation assembly strategy. The package of PDA provides a large number of nitrogen-containing functional groups that can serve as adsorption sites for gold ions, resulting in a 21.8% increase in the ability of the material to recover gold. Fe/Co-MOF@PDA NH possesses high gold recovery capacity (1478.87 mg g-1) and excellent gold selectivity (Kd = 5.71 mL g-1). With the assistance of an in situ magnetic field, the gold recovery capacity of Fe/Co-MOF@PDA NH is increased from 1217.93 to 1478.87 mg g-1, and the recovery rate increased by 24.7%. The above excellent performance is attributed to the efficient reduction of gold by FDC/FC+, Co2+/Co3+ double reducing couple, and the optimization of the reduction reaction by the magnetic field. After the samples are calcined, high-purity gold (95.6%, 22K gold) is recovered by magnetic separation. This study proposes a forward-looking in situ energy field-assisted strategy to enhance precious metal recovery, which has a guiding role in the development of low-carbon industries.

Enhanced Cr(VI) elimination from water by goethite-impregnated activated carbon coupled with weak electric field

A weak electric field (WEF, 2 mA cm-2) was employed to promote Fe(III)/Fe(II) cycle on goethite-impregnated activated carbon (FeOOH@AC) filled in a continuous-flow column for enhanced Cr(VI) elimination from water. Surficial analysis and Cr species distribution showed that α-FeOOH of 0.2-1 μm was successfully synthesized and evenly loaded onto AC. Electron transfer from WEF to α-FeOOH was facilitated with AC as electron shuttles, thereby boosting Fe(III) reduction in the α-FeOOH. The generated Fe(II) reduced Cr(VI) and the resultant Cr(III) subsequently precipitated with OH- and Fe(III) to form Cr(OH)3 and (CrχFe1-χ)(OH)3. Therefore, the WEF-FeOOH@AC column exhibited a much lower Cr(VI) migration rate of 0.0018 cm PV-1 in comparison with 0.0037 cm PV-1 of the FeOOH@AC column, equal to 104 % higher Cr(VI) elimination capacity and 90 % longer column service life-span. Additionally, under different Cr(VI) loadings by varying either seepage velocities or influent Cr(VI) concentrations, the WEF-FeOOH@AC column maintained 1.0-1.5 folds higher Cr(VI) elimination and 0.9-1.4 folds longer longevity than those of the FeOOH@AC column owing to the interaction between FeOOH@AC and WEF. Our research demonstrated that WEF-FeOOH@AC was a potential method to promote Cr(VI) elimination from water and offer an effective strategy to facilitate Fe(III)/Fe(II) cycle in iron oxides.

Sustainable energy and waste management: How to transform plastic waste into carbon nanostructures for electrochemical supercapacitors

Plastic waste consumption increases exponentially every year, mainly in the last three years due to the COVID-19 pandemic. The rapid growth of plastic products has exceeded the world's capacity to deal with this type of trash. Thus, it has become a substantial environmental concern in modern society. Another dire concern is the improper disposal of used supercapacitors, leading to serious environmental impacts. Consequently, critical action to tackle this issue is to transform trash into high-valued materials, such as carbon nanomaterial supercapacitors. Considering several methodologies of recycling, pyrolysis stands out due to its simplicity and easy handling of mixed plastic waste to produce carbonaceous materials with different dimensions (0, 1, 2, and 3D). Thus, from this technology, it is possible to create new opportunities for using plastic waste and other types of waste to produce cheaper carbon-based materials for supercapacitors. This review aims to provide readers with a sustainability-driven view regarding the reutilization of plastic trash, discusses the environmental consequences of not doing so, and shows plastic waste solutions. Despite the broad scope of the topic, this review focuses on identifying the currently studied strategies to convert plastic waste into carbon-based electrodes, using less expensive and more efficient competitive protocols, besides emphasizing the diverse types (0, 1, 2, and 3D) of nanostructures. This review also proposes promising options for a sustainable cycle of plastic waste and supercapacitor.

Agricultural waste to real worth biochar as a sustainable material for supercapacitor

Biochar made from agricultural waste is gaining more attention in energy field due to its sustainability, low cost, apart from having high supercapacitance performance. Also, it has a wide range of environmental applications, including wastewater treatment, upgrading soil fertility, contaminant immobilization, and in situ carbon sequestration. The existing thermo-chemical methodologies for converting agricultural waste into a sustainable material i.e. biochar and the role of activation agents in enhancing the performance of these materials were critically analyzed and discussed. An overview of recent trends in agricultural waste-derived biochar for supercapacitor electrodes is highlighted in this review that emphasizes green circular economy for encouraging net-zero utility of agriculture waste biomass. The roles of various newly prepared "green" electrolytes in reducing the negative consequences of supercapacitor is also reviewed. The trashing of agricultural waste and the depletion of energy supplies has become a global concern, hurting the world's ecosystem and economy through pollution and a fuel crisis and hence the concept of a green circular economic model is also highlighted.

Optimization of Cr (VI) removal from aqueous solution with activated carbon derived from Eichhornia crassipes under response surface methodology

Tannery industries' effluent contains a high concentration of Cr (VI) which has the potential to affect the environment and public health. Therefore, this study aimed to investigate the optimization of Cr (VI) adsorption by activated carbon (AC) derived from Eichhornia crassipes from an aqueous solution. The adsorbent was activated with dilute sulfuric acid followed by thermal activation. AC was characterized using proximate analysis, SEM, FTIR, X-ray diffraction, and the BET method. The Cr (VI) removal optimization process was performed using a central composite design under the response surface methodology. The proximate analysis showed that the moisture content, volatile matter, ash content, and fixed carbon of the activated carbon were 5.6%, 18.2%, 14.4%, and 61.8% respectively. The surface areas of the Eichhornia crassipes before activation, after activation, and after adsorption were 60.6 g/m², 794.2 g/m², and 412.6 g/m² respectively. A highly porous structure with heterogeneous and irregular shapes was observed in the SEM micrograph. In the FTIR analysis, different peaks are indicated with various functional groups. The intensity of XRD peaks decreased as 2 theta values increased, which indicates the presence of an amorphous carbon arrangement. The point of zero charge (pH_pzc) of the activated carbon was found to be 5.20. A maximum Cr (VI) removal of 98.4% was achieved at pH 5, contact time 90 min, adsorbent dose 2 g, and initial Cr (VI) concentration of 2.25 mg/L. Statistically significant interactions (P < 0.05) were observed between the initial Cr (VI) concentration and adsorbent dose as well as the initial Cr (VI) concentration and contact time. Langmuir adsorption isotherm fitted the experimental data best, with an R² value of 0.99. The separation constant (RL) indicates that the adsorption process is favorable. The kinetic experimental data were best fitted with the pseudo-second-order model with an R² value of 0.99 whereas the adsorption rate is controlled by intraparticle and extragranular diffusion processes. Generally, the AC has the potential to be a strong adsorbent candidate for wastewater treatment at the industrial level.

Development and Characterization of Bioadsorbents Derived from Different Agricultural Wastes for Water Reclamation: A Review

The presence of dangerous pollutants in different water sources has restricted the availability of this natural resource. Thus, the development of new low-cost and environmentally-friendly technologies is currently required to ensure access to clean water. Various approaches to the recovery of contaminated water have been considered, including the generation of biomaterials with adsorption capacity for dangerous compounds. Research on bioadsorbents has boomed in recent years, as they constitute one of the most sustainable options for water treatment thanks to their abundance and high cellulose content. Thanks to the vast amount of information published to date, the present review addresses the current status of different biosorbents and the principal processes and characterization methods involved, focusing on base biomaterials such as fruits and vegetables, grains and seeds, and herbage and forage. In comparison to other reviews, this work reports more than 60 adsorbents obtained from agricultural wastes. The removal efficiencies and/or maximum adsorption capacities for heavy metals, industrial contaminants, nutrients and pharmaceuticals are presented as well. In addition to the valuable information provided in the literature investigation, challenges and perspectives concerning the implementation of bioadsorbents are discussed in order to comprehensively guide selection of the most suitable biomaterials according to the target contaminant and the available biowastes.

Indium sulfide deposited MIL-53(Fe) microrods: Efficient visible-light-driven photocatalytic reduction of hexavalent chromium

The ecosystems and human health were seriously threatened by hexavalent chromium (Cr(VI)) in wastewater. In this article, using the idea of the highly matched energy band structure between indium sulfide (In₂S₃) and MIL-53(Fe), a Type-II heterojunction has been constructed by loading In₂S₃ on MIL-53(Fe) microrod to overcome the fault like high recombination rates of photogenerated electron-holes of In₂S₃. The composite with 20:1 mass ratio of In₂S₃ to MIL-53(Fe) (IM-2) was adopted as an optimal sample for efficient photocatalytic Cr(VI) reduction under visible light. Various characterization techniques were used to verify the characteristics of composites and delved into the structure-effect relationship between this heterojunction and its activity. Results showed that the reaction rate constants of the photoreduction process over IM-2 was ~ 4 and 26 times higher than those of pure In₂S₃ and MIL-53(Fe), respectively, and the catalyst could maintain superior removal efficiency (88.6%) and steady crystal structure after four cycles. First-principles calculations further illustrated that the heterostructure formed between In₂S₃ and MIL-53(Fe) could effectively accelerate the separation of photogenerated electrons and holes, thus improving the photocatalytic reduction performance. Moreover, the active species analyses revealed that the superoxide radicals and electrons were mainly involved in the reduction of Cr(VI).

Facile Fabrication of Novel NiFe2O4@Carbon Composites for Enhanced Adsorption of Emergent Antibiotics

Water purification is becoming one of the most pertinent environmental issues throughout the world. Among common types of water pollution involving heavy metals, pharmaceutical drugs, textile dyes, personal care products, and other persistent organic pollutants, the pollution of antibiotic drugs is increasingly emerging due to their adverse effects on microorganisms, aquatic animals, and human health. Therefore, the treatment of such contaminants is very necessary to reduce the concentration of antibiotic pollutants to permissible levels prior to discharge. Herein, we report the use of NiFe₂O₄@C composites from a bimetallic-based metal-organic framework Ni-MIL-88B(Fe) for removal of ciprofloxacin (CFX) and tetracycline (TCC). The effect of production temperatures (600–900 °C), solution pH (2–10), NiFe₂O₄@C dose (0.05–0.2 g/L), concentration of antibiotics (10–60 mg/L), and uptake time (0–480 min) was investigated systematically. Response surface methodology and central composite design were applied for quadratic models to discover optimum conditions of antibiotic adsorption. With high coefficients of determination (R² = 0.9640–0.9713), the proposed models were significant statistically. Under proposed optimum conditions, the adsorption capacity for CFX and TCC were found at 256.244, and 105.38 mg/g, respectively. Recyclability study was employed and found that NiFe₂O₄@C-900 could be reused for up to three cycles, offering the potential of this composite as a good adsorbent for removal of emergent antibiotics.

A new insight into the restriction of Cr(VI) removal performance of activated carbon under neutral pH condition

Activated carbon has been widely used to remove hazardous Cr(VI); however, the impact of Cr₂O₃ precipitate on gradually declining removal ability as pH increases has received little attention. Herein, to investigate the effect of Cr₂O₃, SEM-EDX (scanning electron microscope-energy dispersive X-ray analysis) coupling elements mapping of chromium-loaded powdered activated carbon (PAC) revealed that a chromium layer was formed on the PAC exterior after being treated with Cr(VI) at pH 7. XPS (X-ray photoelectron spectroscopy) study confirmed that 69.93% and 39.91% Cr₂O₃ precipitated on the PAC surface at pH 7 and pH 3, respectively, corresponding to 17.77 mg/g and 20 mg/g removal capacity. Exhausted PAC had a removal efficiency of 92.43% after Cr₂O₃ being washed by H₂SO₄ solution, which was much higher than the removal efficiency of 51.27 % after NaOH washing. This further verified that the intrinsically developed Cr₂O₃ precipitate on PAC under neutral conditions limited the durability of PAC as an adsorbent. Consecutive elution assessments confirmed that adsorption and reduction ability both declined as pH increased. Raman spectroscopy and C 1s spectra of materials demonstrated two distinct Cr(VI) removal mechanisms under pH 3 and pH 7. In conclusion, the exhausted AC after Cr(VI) adsorption can be rejuvenated after the surface coated Cr₂O₃ is washed by the acid solution, which can expand the longevity of AC and recover Cr(III).

Efficient and selective removal of Ag+ as nano silver particles by the composite of SiO2 supported nano ferrous oxalate

Developing novel environmentally materials with high capacity and selectivity for Ag⁺ adsorption by transforming Ag⁺ to nano silver is important for the recovery of precious metals from Ag-containing solution. The present study systematically studied the Ag ⁺ adsorption process from solution by the composite of SiO₂ supported nano ferrous oxalate (SNFO) synthesized from biotite-containing minerals. Batch experiments, dynamics and isothermal adsorption fitting results showed that Ag⁺ removal behaviours were in accordance with the pseudo-first-order kinetic model and Langmuir model, and the maximal Ag⁺ removal capacity was 223.68 mg/g. Thermodynamic fitting results suggested that Ag ⁺ removal by the composite was a spontaneous and endothermic reaction process. XRD and TEM revealed that the reaction products were consisted of SiO₂ and nano silver particles, and FTIR and XPS results indicated that the Ag⁺ removal mechanisms were attributed to the synergistic reduction interaction between ferrous and the anions of oxalate. Meanwhile, the composite possesses high selectivity for Ag⁺ removal even at low Ag⁺ concentration. Moreover, the size of nano silver particles could be adjusted by different pH values. All above results demonstrated that the composite was an ideal material for selective recovery of Ag⁺ from Ag⁺ containing effluents in the form of nano silver.

Adsorptive performance of activated carbon reused from household drinking water filter for hexavalent chromium-contaminated water

Powdered activated carbon blocks (PACBs) are waste products obtained from household drinking water purification systems. In this study, we demonstrate that they can be used as adsorbents for the cost-effective and environmentally benign removal of hexavalent chromium (Cr(VI)) from contaminated-water and rinse electroplating wastewater. To evaluate Cr(VI) sorption onto the PACB, studies on equilibrium, kinetics, and thermodynamics were performed using batch mode experiments. The experimental results indicated that Cr(VI) ions were efficiently adsorbed under acidic conditions (i.e., at initial pH below 3) and low initial Cr(VI) concentrations. The adsorptive behaviors of the PACB for Cr(VI) were well explained by the Langmuir isotherm, as well as pseudo-second-order kinetic models, suggesting that a Cr(VI) monolayer was adsorbed onto the PACB surface via chemisorption. The maximum adsorption capacity of Cr(VI) onto the PACB was determined to be 6.207 mg/g. The results of thermodynamic studies revealed that the adsorption process of Cr(VI) onto PACB was endothermic and non-spontaneous. Additionally, analysis of the PACB after Cr(VI) adsorption at an initial pH of 2 using scanning electron microscopy, energy dispersive spectrometry, Fourier transform infrared spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) revealed that the interaction between the surface oxygenic functional groups on the PACB and Cr(VI) was primarily responsible for Cr(VI) sorption via surface complexation and electrostatic interactions. Based on the result of XPS analysis, the presence of trivalent chromium on the PACB surfaces indicated that some synergistic redox reactions involving Cr(VI) could have occurred during the sorption process. Although a commercially available powdered activated carbon outperformed the PACB adsorbent with respect to Cr(VI) removal from wastewater, complete Cr(VI) adsorption could be achieved using relatively large quantities of the PACB. These findings indicate that the PACB adsorbent could be used as a cheap and efficient material for the removal of Cr(VI) from wastewater.

One-dimensional graphene for efficient aqueous heavy metal adsorption: Rapid removal of arsenic and mercury ions by graphene oxide nanoribbons (GONRs)

There is a knowledge gap for the application of one-dimensional graphene in the adsorption process. Our hypothesis was based on the fact that graphene oxide nanoribbons (GONRs) as one-dimensional graphene with more desired edges and specific surface area than other carbonaceous nanomaterials have more oxygen containing functional groups (active sites) on their edges and basal planes and therefore are more capable in adsorption of pollutants. In this regard, we synthesized GONRs by unzipping of multi-walled carbon nanotubes (MWCNTs) and investigated the adsorption behavior of GONRs by ultrasonic-assisted adsorptive removal of As(V) and Hg(II) ions from aqueous solution. The obtained results showed that As(V) ions are more favorably adsorbed onto the GONRs than Hg(II) ions and with increasing initial As(V) and Hg(II) ions concentration to 300 ppm, the equilibrium adsorption uptake of the synthesized GONRs increases to 155.61 and 33.02 mg/g for As(V) and Hg(II) ions, respectively through a rapid separation process in just 12 min. Also, three kinetic models and Freundlich and Langmuir adsorption isotherms were applied to evaluate the obtained experimental results. Our findings highlight the potential application of GONRs as one-dimensional graphene adsorbent with more desired edges than MWCNTs and graphene oxide (GO) and high adsorption capacity for selective removal of heavy metals.