Effects of copper on biological treatment of NMF- and MDG-containing wastewater from TFT-LCD industry

Detection Method and Common Characteristics of Waste Solvent from Semiconductor Industry

The recycling of organic solvents is a widely discussed topic. The waste organic solvents from thin-film-transistor liquid-crystal display (TFT-LCD) production is characterized by large quantities, multiple types, and complex compositions. Thus, the unified and compatible component analysis method is important for studying the recovery of waste organic solvents. In our work, based on the study of existing analytical methods, we designed a compatible method for the analysis of moisture using Karl Fischer analysis, for the analysis of organic compounds using gas chromatography, and for the analysis of the photoresist and other solids by evaporation. These were specific methods for analyzing the components of near-total formulation thin-film-transistor liquid-crystal display waste organic solvent. The organic matter content was analyzed via gas chromatography with a CP-Sil8CB column and flame ionization detector. The initial temperature of the column was 90 °C and the holding time was 1 min. The heating rate was 30 °C/min. The temperature was raised to 270 °C for 7 min. The internal standard method and the external standard method were used to determine the content of the main components of organic compounds. The relative standard deviation of the analytical results was 1.14~2.93%, 1.21~4.74% and 0.61%, respectively. The analytical results had good accuracy, but the external standard method was better; the recoveries were 99.76~107.60%, 95.86~107.70%, and 95.23~96.88%, respectively. Based on the composition analysis, the composition rule of the waste organic solvent was summarized. Through the exploration of the effect of the waste solvent, the common characteristics of the waste solvent were obtained. This study provides a good strategy and an optimized method for improving the efficiency of organic solvent recovery.

PVDF Composite Membranes with Hydrophobically-Capped CuONPs for Direct-Contact Membrane Distillation

Water scarcity is an imminent problem that humanity is beginning to attempt to solve. Among the several technologies that have been developed to mitigate water scarcity, membrane distillation is of particular note. In the present work, CuO nanoparticles capped with 1-octanethiol (CuONPs@CH) or 1H,1H,2H,2H-perfluorodecanethiol (CuONPs@CF) are prepared. The nanoparticles are characterized by FT-IR and TGA methods. Two weight losses are observed in both cases, with the decomposition of the organic fragments beginning at 158 °C and 230 °C for CuONPs@CF and CuONPs@CH, respectively. Flat sheet PVDF composite membranes containing nanoparticles are prepared by the casting solution method using nanoparticle concentrations that ranged between 2-20% with a non-woven polyester fabric as support. The obtained membranes showed a thickness of 240 ± 40 μm. According to water contact angle (87° for CuONPs@CH and 95° for CuONPs@CF, both at 10% w.t) and roughness (12 pixel for CuONPs@CH and 14 pixels for CuONPs@CF, both at 10% w.t) determinations, the hydrophobicity of membranes changed due to a decrease in surface energy, while, for naked CuONPs, the roughness factor represents the main role. Membranes prepared with capped nanoparticles showed similar porosity (60-64%). SEM micrographs show asymmetric porous membranes with a 200-nm surface pore diameter. The largest finger-like pores in the membranes prepared with CuONPs, CuONPs@CH and CuONPs@CF had values of 63 ± 10 μm, 32 ± 8 μm, and 45 ± 10 μm, respectively. These membranes were submitted to a direct contact membrane distillation module and flux values of 1.8, 2.7, and 3.9 kg(m2·h)-1 at ΔT = 30 °C were obtained for the CuONPs, CuONPs@CH, and CuONPs@CF, respectively. The membranes showed 100% salt rejection during the testing time (240 min).