Photocatalytic activity of G-TiO2@Fe3O4 with persulfate for degradation of alizarin red S under visible light

Visible-light-driven TiO2@Fe2O3/Chitosan nanocomposite with promoted photodegradation of meropenem and imipenem antibiotics by peroxymonosulfate

This study assessed wastewater treatment by visible-light/Peroxymonosulfate process using its linking with TiO2@Fe3O4 nanoparticles coated on chitosan. Meropenem and Imipenem photodegradation was evaluated as a model-resistant contaminant by TiO2@Fe2O3/chitosan nanocomposite. The synthesised TiO2@Fe2O3/chitosan was characterised using various techniques. Fe2O3 and TiO2 nanoparticles on the chitosan surface were affirmed via XRD, EDX, and FTIR findings. The FESEM and TEM results verified the deposition of TiO2@Fe2O3 on the chitosan surface. Under optimum circumstances (pH = 4, catalyst dosage = 0.5 g/L, antibiotics concentration = 25 mg/L reaction time = 30 min, and PMS = 2 mM), maximum degradation efficiency was obtained at about 95.64 and 93.9% for Meropenem and Imipenem, respectively. Also, the experiments demonstrated that TiO2@Fe2O3/chitosan had a better performance than photolysis and adsorption by catalyst without visible light irradiation in degrading antibiotics. The scavenger tests confirmed that O 2 ⋅ - , SO 4 ⋅ - , HO ⋅ , and h+ are present simultaneously during the pollutant photodegradation process. After five recovery cycles, the system eliminated over 80 percent of antibiotics. It suggested that the catalyst's capacity to be reused may be cost-effective.

Boosting the performance of LaCoO3/MoS2 perovskite interface for sustainable decontaminants under visible light-driven photocatalysis

The novel composite LaCoO3/MoS2 hybrid nanostructure was synthesized via a combination of sol-gel, hydrothermal, and ultrasonication methods. Alizarin Red S (ARS) and Rhodamine B (RhB) were employed as a model pollutant, to assess the photodegradation efficiency of synthesized catalysts. The effect of MoS2 (2.5%, 5%, 7.5%, and 10%) on LaCoO3 (LCO) and its photocatalytic performance was studied. The properties of synthesized catalysts were assessed using various material characterization techniques. The photocatalytic dye degradation of ARS and RhB was investigated under visible light. Among the synthesized catalyst LM-5% composite (LaCoO3 with 5% MoS2) is determined to be the best photocatalyst as it degrades 96 % (ARS) and 90 % (RhB) in 40 min and 80 min, respectively. The photocatalyst is stable even after multiple runs and exhibits negligible loss in degradation efficiency during the cyclic test. Trapping experiments reveal the significance of superoxide anion and hydroxyl radicals against the photodegradation of ARS and RhB. The kinetics of photodegradation of ARS and RhB by LM-5% is found to be 5.70 × 10-2 and 2.25 × 10-2 min-1, respectively. Herein, we demonstrated a catalyst possessing excellent photodegradation activity which may ignite the possibilities of using efficient photocatalysts for environmental remediation.

Mesoporous Cu-Doped Manganese Oxide Nano Straws for Photocatalytic Degradation of Hazardous Alizarin Red Dye

The present work reports the photocatalytic degradation of alizarin red (AR) using Cu-doped manganese oxide (MH16-MH20) nanomaterials as catalysts under UV light irradiation. Cu-doped manganese oxides were synthesized by a very facile hydrothermal approach and characterized by energy dispersive X-ray spectroscopy, powder X-ray diffraction, scanning electron microscopy, Brunauer-Emmett-Teller analysis, UV-vis spectroscopy, and photoluminescence techniques. The structural, morphological, and optical characterization revealed that the synthesized compounds are nanoparticles (38.20-54.10 nm), grown in high mesoporous density (constant C > 100), possessing a tetragonal phase, and exhibiting 2.98-3.02 eV band gap energies. Synthesized materials were utilized for photocatalytic AR dye degradation under UV light which was monitored by UV-visible spectroscopy and % AR degradation was calculated at various time intervals from absorption spectra. More than 60% AR degradation at various time intervals was obtained for MH16-MH20 indicating their good catalytic efficiencies for AR removal. However, MH20 was found to be the most efficient catalyst showing more than 84% degradation, hence MH20 was used to investigate the effect of various catalytic doses, AR concentrations, and pH of the medium on degradation. More than 50% AR degradation was obtained for all studied parameters with MH20 whereas the pseudo-first-order kinetic model was found to be the best-fitted kinetic model for AR degradation with k = 0.0015 and R2 = 0.99 indicating a significant correlation between experimental data.

Remediation of environmentally persistent organic pollutants (POPs) by persulfates oxidation system (PS): A review

Over the past few years, persistent organic pollutants (POPs) exhibiting high ecotoxicity have been widely detected in the environment. Persulfate-oxidation hybrid system is one of the most widely used novel advanced oxidation techniques and is based on the persulfate generation of SO₄^-∙ and ∙OH from persulfate to degrade POPs. The overarching aim of this work is to provide a critical review of the variety of methods of peroxide activation (e.g., light activated persulfate, heat-activated persulfate, ultrasound-activated persulfate, electrochemically-activated persulfate, base-activated persulfate, transition metal activated persulfate, as well as Carbon based material activated persulfate). Specifically, through this article we make an attempt to provide the important characteristics and uses of main activated PS methods, as well as the prevailing mechanisms of activated PS to degrade organic pollutants in water. Finally, the advantages and disadvantages of each activation method are analyzed. This work clearly illustrates the benefits of different persulfate activation technologies, and explores persulfate activation in terms of Sustainable Development Goals, technical feasibility, toxicity assessment, and economics to facilitate the large-scale application of persulfate technologies. It also discusses how to choose the most suitable activation method to degrade different types of POPs, filling the research gap in this area and providing better guidance for future research and engineering applications of persulfates.

Photocatalytic mechanism conversion of titanium dioxide induced via surface interface coordination

Photocatalytic removal of organic pollutants is a promising pollution treatment technology from the aspect of carbon neutrality. The complex diversity of actual wastewater components, as opposed to single-component systems, can significantly affect photocatalytic mechanisms. In this study, complex pollutant systems were created using various coordinating agents, and the effects of P25 on the photocatalytic removal of methyl orange (MO) in these systems and corresponding photocatalytic mechanism were investigated. The results show that photocatalytic removal of MO by P25 using ligands is significantly more efficient, especial removal of MO by the EDTA-P25 (P-E_2.5) coordination system resulted dramatically improved MO removal (97.4% versus 12.3% achieved by pure P25 after 15 min), with the reaction rate improved 23.8-fold. Theoretical calculations show that the effective coordination bonds formed by the coordinating agent and Ti atoms reduce the adsorption energy of P25 for MO. In addition, introduction of the coordinating agent EDTA reduces the transition state energy during the MO degradation process and greatly accelerates the reaction rate, and the conduction band position of the EDTA-P25 coordination system shifts to a more negative potential, which induces to the generation of •O₂^- for effective MO degradation.

State-of-the-Art on the Sulfate Radical-Advanced Oxidation Coupled with Nanomaterials: Biological and Environmental Applications

Sulfate radicals (SO₄^-·) play important biological roles in biomedical and environmental engineering, such as antimicrobial, antitumor, and disinfection. Compared with other common free radicals, it has the advantages of a longer half-life and higher oxidation potential, which could bring unexpected effects. These properties have prompted researchers to make great contributions to biology and environmental engineering by exploiting their properties. Peroxymonosulfate (PMS) and peroxydisulfate (PDS) are the main raw materials for SO₄^-· formation. Due to the remarkable progress in nanotechnology, a large number of nanomaterials have been explored that can efficiently activate PMS/PDS, which have been used to generate SO₄^-· for biological applications. Based on the superior properties and application potential of SO₄^-·, it is of great significance to review its chemical mechanism, biological effect, and application field. Therefore, in this review, we summarize the latest design of nanomaterials that can effectually activate PMS/PDS to create SO₄^-·, including metal-based nanomaterials, metal-free nanomaterials, and nanocomposites. Furthermore, we discuss the underlying mechanism of the activation of PMS/PDS using these nanomaterials and the application of SO₄^-· in the fields of environmental remediation and biomedicine, liberating the application potential of SO₄^-·. Finally, this review provides the existing problems and prospects of nanomaterials being used to generate SO₄^-· in the future, providing new ideas and possibilities for the development of biomedicine and environmental remediation.

Enhanced synchronous photocatalytic 4-chlorophenol degradation and Cr(VI) reduction by novel magnetic separable visible-light-driven Z-scheme CoFe2O4/P-doped BiOBr heterojunction nanocomposites

The co-existence of organic contaminants and heavy metals including 4-chlorophenol (4-CP) and Cr(VI) in aquatic system have become a challenging task in the wastewater treatment. Herein, the synchronous photocatalytic decomposition of 4-CP and Cr(VI) over new Z-scheme CoFe₂O₄/P-BiOBr heterojunction nanocomposites were revealed. In this work, the nanocomposites were successfully developed via a surfactant-free hydrothermal method. The heterojunction interface was created by decorating magnetic CoFe₂O₄ nanoparticles onto P-BiOBr nanosheets. The as-fabricated CoFe₂O₄/P-BiOBr nanocomposites substantially improved the synchronous decomposition of 4-CP and Cr(VI) compared to the single-phase component samples under visible light irradiation. Particularly, the 30-CoFe₂O₄/P-BiOBr nanocomposite displayed the best photocatalytic performance, which decomposed 95.6% 4-CP and 100% Cr(VI) within 75 min. The photocatalytic improvement was assigned to the Z-scheme heterojunction assisted charge migration between CoFe₂O₄ and P-BiOBr, and the acceleration of charge carrier separation was validated by the findings of charge dynamics measurements. The harmful 4-CP was photodegraded into smaller organics whereas the Cr(VI) was photoreduced into Cr(III) after 30-CoFe₂O₄/P-BiOBr photocatalysis, and the good recyclability of fabricated nanocomposite in photocatalytic reaction also showed promising potential for practical applications in environmental remediation. Finally, the radical quenching tests confirmed that there existed the Z-scheme path of charge migration in CoFe₂O₄/P-BiOBr nanocomposite, which was the mechanism responsible for its high photoactivity.

A comprehensive review on persulfate activation treatment of wastewater

With increasingly serious environmental pollution and the production of various wastewater, water pollutants have posed a serious threat to human health and the ecological environment. The advanced oxidation process (AOP), represented by the persulfate (PS) oxidation process, has attracted increasing attention because of its economic, practical, safety and stability characteristics, opening up new ideas in the fields of wastewater treatment and environmental protection. However, PS does not easily react with organic pollutants and usually needs to be activated to produce oxidizing active substances such as sulfate radicals (SO₄^-) and hydroxyl radicals (OH) to degrade them. This paper summarizes the research progress of PS activation methods in the field of wastewater treatment, such as physical activation (e.g., thermal, ultrasonic, hydrodynamic cavitation, electromagnetic radiation activation and discharge plasma), chemical activation (e.g., alkaline, electrochemistry and catalyst) and the combination of the different methods, putting forward the advantages, disadvantages and influencing factors of various activation methods, discussing the possible activation mechanisms, and pointing out future development directions.

Photocatalytic activity of ZrO2/TiO2/Fe3O4 ternary nanocomposite for the degradation of naproxen: characterization and optimization using response surface methodology

In this study, ZrO₂, TiO₂, and Fe₃O₄ components were synthesized by co-precipitation, sol–gel, and co-precipitation methods, respectively. In addition, solid-state dispersion method was used for synthesizing of ZrO₂/TiO₂/Fe₃O₄ ternary nanocomposite. The ZrO₂/TiO₂/Fe₃O₄ nanocomposite was characterized by different techniques including XRD, EDX, SEM, BET, FTIR, XPS, EELS, and Photoluminescence (PL). The FTIR analysis of ZrO₂/TiO₂/Fe₃O₄ photocatalyst showed strong peaks in the range of 450 to 700 cm⁻¹, which represent stretching vibrations of Zr–O, Ti–O, and Fe–O. The results of FTIR and XRD, XPS analyses and PL spectra confirmed that the solid-state dispersion method produced ZrO₂/TiO₂/Fe₃O₄ nanocomposites. The EELS analysis confirmed the pure samples of Fe₃O₄, TiO₂ and ZrO₂. The EDAX analysis showed that the Zr:Ti:Fe atomic ratio was 0.42:2.08:1.00. The specific surface area, pores volume and average pores size of the photocatalyst were obtained 280 m²/g, 0.92 cm³/g, and 42 nm respectively. Furthermore, the performance of ZrO₂/TiO₂/Fe₃O₄ nanocomposite was evaluated for naproxen removal using the response surface method (RSM). The four parameters such as NPX concentration, time, pH and catalyst concentration was investigated. The point of zero charge of the photocatalyst was 6. The maximum and minimum degradation of naproxen using photocatalyst were 100% (under conditions: NPX concentration = 10 mg/L, time = 90 min, pH = 3 and catalyst concentration = 0.5 g/L) and 66.10% respectively. The stability experiment revealed that the ternary nanocatalyst demonstrates a relatively higher photocatalytic activity after 7 recycles.

Synergistic degradation of fluorene in soil by dielectric barrier discharge plasma combined with P25/NH2-MIL-125(Ti)

Plasma techniques to degrade pollutants are generally more efficient than conventional methods, but exist some problems such as high energy consumption, incomplete degradation of pollutants, and secondary pollution caused by highly toxic intermediates. In this study, the dielectric barrier discharge plasma (DBDP) combined with the Ti-based metal organic frameworks (MOFs) catalysts (P25/NH₂-MIL-125(Ti)) was used to degrade fluorene in the soil. The synergistic treatment technique used in soil remediation can realize a green and promising treatment efficiency with relatively low energy consumption. Compared with DBDP system alone, the synergetic treatment system of DBDP and P25/NH₂-MIL-125(Ti) considerably increased the degradation efficiency of fluorene in the soil to above 90% at 10 min, even with a relatively low discharge voltage (5 kV). The synergistic treatment system achieved 88.8% of fluorene mineralization at 60 min. Optical emission spectroscopy and electron paramagnetic resonance spectroscopy both showed that •OH and •O₂^- played an important role in the synergetic treatment system. Nine main intermediates were identified using gas chromatography-mass spectrometry and Fourier transform infrared analysis. The main degradation of fluorine in soil was caused by the electronic transition of the catalytic material excited by DBDP, and finally mineralized into CO₂ and H₂O. The fluorene and its toxic intermediates were effectively removed. This study provides an insight for achieving high efficiency and environmentally friendly application perspective in soil remediation.

Study of Influence Factors in the Evaluation of the Performance of a Photocatalytic Fibre Reactor (TiO2/SiO2) for the Removal of Organic Pollutants from Water

The performance of a photocatalytic fibre reactor (UBE Chemical Europe), made of cartridges of fine particles of TiO2 dispersed within silicon fibres and irradiated by ultraviolet light, for the removal of organic pollutants from synthetic waters was evaluated. In the sensitivity analysis carried out, the factors catalytic surface area, fibre state, temperature and initial substrate concentration were studied using 4-chlorophenol as a test compound. The percentage of titanium in the fibre remained practically invariable after a series of experiments and cleaning procedures. Furthermore, the kinetics of removal of pyrene, phenol, 4-chlorophenol and bisphenol A (BPA) from water were evaluated by means of HPLC, UV-absorption and fluorescence techniques. Kinetic operational parameters were determined from a mathematical model proposed by Langmuir–Hinshelwood. Results show that catalytic surface, initial substrate concentration and temperature directly affect the degradation rate of organic compounds, whereas fibre state does not have a significant effect on that. It is proposed that removal of organic compounds from water mainly depends on the adsorption of the specific pollutant on the photocatalytic fibre and on the physical diffusion of the substrate towards the photocatalytic TiO2 active sites on the fibre, with the heterogeneous phase reaction prevailing over the homogeneous phase reaction.

The mechanism of degradation of alizarin red by a white-rot fungus Trametes gibbosa

Background

Alizarin red (AR) is a typical anthraquinone dye, and the resulting wastewater is toxic and difficult to remove. A study showed that the white rot fungus Trametes gibbosa (T. gibbosa) can degrade dye wastewater by decolorization and has its own enzyme-producing traits.

Methods

In this study, transcriptome sequencing was performed after alizarin red treatment for 0, 3, 7, 10, and 14 h. The key pathways and key enzymes involved in alizarin red degradation were found to be through the analysis of KEGG and GO. The Glutathione S-transferase (GST), manganese peroxidase (MnP) and laccase activities of T. gibbosa treated with alizarin red for 0–14 h were detected. LC–MS and GC–MS analyses of alizarin red decomposition products after 7 h and 14 h were performed.

Results

The glutathione metabolic pathway ko00480, and the key enzymes GST, MnP, laccase and CYP450 were selected. Most of the genes encoding these enzymes were upregulated under alizarin red conditions. The GST activity increased 1.8 times from 117.55 U/mg prot at 0 h to 217.03 U/mg prot at 14 h. The MnP activity increased 2.9 times from 6.45 to 18.55 U/L. The laccase activity increased 3.7 times from 7.22 to 27.28 U/L. Analysis of the alizarin red decolourization rate showed that the decolourization rate at 14 h reached 20.21%. The main degradation intermediates were found to be 1,4-butene diacid, phthalic acid, 1,1-diphenylethylene, 9,10-dihydroanthracene, 1,2-naphthalene dicarboxylic acid, bisphenol, benzophenol-5,2-butene, acrylaldehyde, and 1-butylene, and the degradation process of AR was inferred. Overall, 1,4-butene diacid is the most important intermediate product produced by AR degradation.

Conclusions

The glutathione metabolic pathway was the key pathway for AR degradation. GST, MnP, laccase and CYP450 were the key enzymes for AR degradation. 1,4-butene diacid is the most important intermediate product. This study explored the process of AR biodegradation at the molecular and biochemical levels and provided a theoretical basis for its application in practical production.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12896-021-00720-8.

Evaluation of the Photocatalytic Activity and Anticorrosion Performance of Electrospun Fibers Doped with Metallic Oxides

This paper reports the development and characterization of a multifunctional coating that combines anticorrosion and photocatalytic properties, deposited by means of the electrospinning technique. In the first step, a functional electrospun fiber mat composed of poly(acrylic acid) (PAA) and β-cyclodextrin (β-CD) was obtained, showing high water insolubility and great adhesion increased by means of a thermal crosslinking process (denoted as PAA + β-CD). In the second step, the fibers were doped with particles of titanium dioxide (denoted as PAA + β-CD/TiO₂) and titanium dioxide plus iron oxide (denoted as PAA + β-CD/TiO₂/Fe₂O₃). The morphology and fiber diameter of the electrospun mats were evaluated by using confocal microscopy, whereas the presence of the metal oxides in the electrospun fibers was corroborated by scanning electron microscopy (SEM) and X-ray fluorescence (XRF), respectively. In addition, electrochemical tests in saline solution revealed that the sample composed of PAA + β-CD/TiO₂/Fe₂O₃ showed the highest corrosion protection efficiency of all the samples, which was directly associated to lower corrosion current density and higher corrosion potential. Furthermore, the paper reports a novel approach to in situ determination of methylene blue (MB) degradation onto the coating. The results revealed complete degradation of MB, which is perfectly appreciated by total discoloration of the film in the irradiated zone (from bluish to a white spot). The main conclusions of this research are the efficiency of the electrospun system PAA + β-CD/TiO₂/Fe₂O₃ for developing photocatalytic activity and corrosion protection and the utility of the dry MB discoloration tests to evaluate photocatalytic activity.